Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Kim, B." wg kryterium: Autor


Tytuł:
Effect of Ergonomic Design Changes in Hand Tools on Physiological Cost and Subjective Ratings
Autorzy:
Kim, B. B. J.
Powiązania:
https://bibliotekanauki.pl/articles/90669.pdf
Data publikacji:
2012
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
ergonomic design
hand tools
electromyographic activity
subjective assessments
Cronbach’s α
Opis:
Users of hand tools expect that tools after ergonomic changes in design will require less muscular activity and cause fewer musculoskeletal disorders than conventional tools. Reports on evaluation of ergonomic design changes in hand tools are controversial. In this study, we measured the effect of changes in tool design with physiological cost of performance and subjective ratings in a simulated setting. We determined physiological cost of performance by measuring muscle activity of the right and left forearm (flexor carpi ulnaris) with electromyography. We collected a questionnaire with subjective ratings before and after each experimental task. Before the tests, ergonomically reconfigured hacksaws received better rating scores than original hacksaws. However, we found no differences in subjective ratings of the hacksaws after the tests. In addition, electromyographic activity did not show any significant differences between the original and modified tools.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2012, 18, 2; 267-277
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of Diabetic Neuropathy on Body Sway and Slip Perturbation Detection in Older Population
Autorzy:
Kim, B. J.
Robinson, C. J.
Powiązania:
https://bibliotekanauki.pl/articles/90072.pdf
Data publikacji:
2006
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
sway
slip
perturbation detection
center of pressure
zagrożenia zdrowia
starsi pracownicy
śliska podłoga
upadek
poślizgnięcie
zaburzenia postawy
neuropatia diabetyczna
diabetyk
Opis:
Postural control is a common mechanism to compensate for unexpected displacements of the body. In the older population, a slip or fall due to a failure of postural control is a common cause of morbidity and mortality. The ability of postural control decreases with aging or neuropathy. In this study, 2 groups, diabetics and non-diabetics in the older population, were compared to determine how patterns of postural sway during quiet standing were related to the detection of perturbation. The SLIP-FALLS system was applied to the measurement of sway and detection of perturbation. In phase 1 of the development of the predictive model, neural network algorithms were applied to find determinant variables for perturbation detection. In phase 2, a fuzzy logic inference system was developed to investigate the relationship between sway and perturbation detection. Results of this study may be applied to the design of floor mats or shoe insoles for preventing fatigue in workplaces.
Źródło:
International Journal of Occupational Safety and Ergonomics; 2006, 12, 3; 241-254
1080-3548
Pojawia się w:
International Journal of Occupational Safety and Ergonomics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Surface Property of Indium Tin Oxide (ITO) After Various Methods of Cleaning
Autorzy:
Kim, K.
Ihm, K.
Kim, B.
Powiązania:
https://bibliotekanauki.pl/articles/1401317.pdf
Data publikacji:
2015-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
73.20.-r
Opis:
We investigated the surface property change of indium tin oxide (ITO) with the various cleaning methods, using photoemission spectroscopy (PES), work function change and near-edge X-ray adsorption fine structure (NEXAFS). The detergent treatments of ITO with acetone (C₃H₆O), methanol (CH₄O), 2-propanol (C₃H₈O), and deionized (D) water yielded work function shifts as high as 0.99 eV compared to the no-treatment ITO. In contrast, work function shifts of 0.10-0.35 eV were measured after other treatments. The lowest C 1s concentration was obtained after O2 plasma treatment of ITO. There was no big change in the peak position and the shape of $In 3d^{5//2}$, and $Sn 3d^{5//2}$ after each treatment. But C 1s and O 1s spectra shows a peak shift and shape change. Presence of carbon can be minimized by NaOH treatment combined with oxygen plasma. In NEXAFS spectra of C K-edge on each sample, we found two π-binding states whose positions are 284.5 and 287.9 eV, C=C and C=O, respectively.
Źródło:
Acta Physica Polonica A; 2015, 127, 4; 1176-1179
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication of Fe-TiB2 Nanocomposites by Spark-Plasma Sintering of a (FeB, TiH2) Powder Mixture
Autorzy:
Huynh, X.-K.
Kim, B.-W.
Kim, J.-S.
Powiązania:
https://bibliotekanauki.pl/articles/351368.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-TiB2 nanocomposite
mechanical activation
spark plasma sintering
self-propagating high-temperature synthesis reaction
Opis:
Fe-40wt% TiB2 nanocomposites were fabricated by mechanical activation and spark-plasma sintering of a powder mixture of iron boride (FeB) and titanium hydride (TiH2). The powder mixture of (FeB, TiH2) was prepared by high-energy ball milling in a planetary ball mill at 700 rpm for 3 h followed by spark-plasma sintering (SPS) at various conditions. Analysis of the change in relative sintered density and densification rate during sintering showed that a self-propagating high-temperature synthesis reaction occurs to form TiB2 from FeB and Ti. A sintered body with relative density higher than 98% was obtained after sintering at 1150°C for 5 and 15 min. The microstructural observation of sintered compacts with the use of FE-SEM and TEM revealed that ultrafine particulates with approximately 5 nm were evenly distributed in an Fe-matrix. A hardness value of 83 HRC was obtained, which is equivalent to that of conventional WC-20 Co systems.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1043-1047
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Mechanical Activation on the in situ Formation of TiB2 Particulates in the Powder Mixture of TiH2 and FeB
Autorzy:
Huynh, X.-K.
Kim, B.-W.
Kim, J. S.
Powiązania:
https://bibliotekanauki.pl/articles/355844.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mechanical activation
in situ formation
TiB2 particulate
Fe-matrix
specific ball-milling energy
Opis:
The in situ formation of TiB2 particulates via an interface reaction between Ti and FeB powders was studied. The effects of mechanical activation by high-energy milling on the decomposition of TiH2 and the interface reactions between Ti and FeB powders to form TiB2 were investigated. Powder mixtures were fabricated using planetary ball-milling under various milling conditions. The specific ball-milling energy was calculated from the measured electrical power consumption during milling process. High specific milling energy (152.6 kJ/g) resulted in a size reduction and homogeneous dispersion of constituent powders. This resulted in a decrease in the decomposition temperature of TiH2 and an increase in the formation reaction of TiB2 particulates in the Fe matrix, resulting in a homogeneous microstructure of nanoscale TiB2 evenly distributed within the Fe matrix. In contrast, the powder mixture milled with low specific milling energy (36.5 kJ/g) showed an inhomogeneous microstructure composed of relatively large Fe-Fe2 B particles surrounded by a thin layer of Fe-TiB2 within a finely dispersed Fe-TiB2 matrix region.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1393-1398
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
CO Oxidation Properties Of Selective Dissoluted Metallic Glass Composites
Utlenianie wybranych rozcieńczonych kompozytów szkieł metalicznych
Autorzy:
Kim, S. Y.
Lee, M. H.
Kim, T. S.
Kim, B. S.
Powiązania:
https://bibliotekanauki.pl/articles/355092.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
CO oxidation
metallic glasses
porous metal
catalyst materials
utlenianie
szkło metaliczne
metale porowate
materiał katalityczny
Opis:
Porous metallic materials have been widely used in many fields including aerospace, atomic energy, electro chemistry and environmental protection. Their unique structures make them very useful as lightweight structural materials, fluid filters, porous electrodes and catalyst supports. In this study, we fabricated Ni-based porous metallic glasses having uniformly dispersed micro meter pores by the sequential processes of ball-milling and chemical dissolution method. We investigated the application of our porous metal supported for Pt catalyst. The oxidation test was performed in an atmosphere of 1% CO and 3% O2. Microstructure observation was performed by using a scanning electron microscope. Oxidation properties and BET (Brunauer, Emmett, and Teller) were analyzed to understand porous structure developments. The results indicated that CO Oxidation reaction was dependent on the specific surface area.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1227-1229
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Manufacturing And High Temperature Oxidation Properties Of Electro-Sprayed Fe-24.5% Cr-5%Al Powder Porous Metal
Wytwarzanie i wysokotemperaturowe utlenianie elektro-rozpylanego porowatego proszku Fe-24.5% Cr-5%Al
Autorzy:
Lee, K-A.
Oh, J-S.
Kong, Y-M.
Kim, B-K.
Powiązania:
https://bibliotekanauki.pl/articles/350912.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
powder porous metal
electro-spray process
electric wire explosion
Fe-24Cr-5Al
high temperature oxidation
porowaty proszek metalu
elektrorozpylanie
utlenianie wysokotemperaturowe
Opis:
Fe-Cr-Al based Powder porous metals were manufactured using a new electro-spray process, and the microstructures and high-temperature oxidation properties were examined. The porous materials were obtained at different sintering temperatures (1350°C, 1400°C, 1450°C, and 1500°C and with different pore sizes (500 μm, 450 μm, and 200 μm). High-temperature oxidation experiments (TGA, Thermal Gravimetry Analysis) were conducted for 24 hours at 1000°C in a 79% N2+ 21% O2, 100 mL/min. atmosphere. The Fe-Cr-Al powder porous metals manufactured through the electro-spray process showed more-excellent oxidation resistance as sintering temperature and pore size increased. In addition, the fact that the densities and surface areas of the abovementioned powder porous metals had the largest effects on the metal’s oxidation properties could be identified.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1169-1173
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Preparation Of Fine Grained SiC At Reduced Temperature By Two-Step Sintering
Wytwarzanie drobnoziarnistego SiC w obniżonej temperaturze przez dwuetapowe spiekanie
Autorzy:
Kim, K.-W.
Oh, K.-S.
Lee, H.
Kim, B. S.
Chung, T.-J.
Powiązania:
https://bibliotekanauki.pl/articles/353772.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
SiC
liquid phase
two step sintering
coarsening
hardness
faza ciekła
spiekanie dwuetapowe
odporność
twardość
Opis:
Two-step sintering route was applied for the densification SiC by promoting the role of liquid phase. The specimen contained 8 vol% of liquid phase composed of Al2O3 and Y2O3. The heating schedule consisted with initial rapid heating to 2000°C and immediate quenching to 1700 or 1750°C. By heating at elevated temperature, even distribution of the liquid phase was intended. The heat treatment at reduced temperature was to suppress the evaporative loss of the liquid and to secure the time for densification. The two-step sintering effectively suppressed loss of mass and coarsening. The resultant SiC was thus dense and was composed of fine grains exhibiting hardness of 2321 kgf/mm2.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1539-1542
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Combined Effect of Zr and Si on Isothermal Oxidation of Ti
Autorzy:
Ha, S.-H.
Kim, B.-H.
Yoon, Y.-O.
Lim, H.-K.
Kim, S. K.
Powiązania:
https://bibliotekanauki.pl/articles/353260.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ti
Zr
Si
silicide
oxidation
Opis:
In this study, the combined effect of Zr and Si on isothermal oxidation of Ti for 25 and 50h at 820°C, which is the temperature related to exhaust valves operation, was investigated. Si addition into Ti-5mass%Zr alloy led to a distribution of silicide Ti5Si3 phase formed by a eutectic reaction. The Ti sample containing only Zr showed more retarded oxidation rate than Ti-6Al-4V, the most prevalent Ti alloy, at the same condition. However, while a simultaneous addition of Zr and Si resulted in greater increase of oxidation resistance. The oxide layer formed after the addition of Zr and Si comprised TiO2, ZrO2, and SiO2.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1493-1495
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics Of The Porous Body Sintered By Nano-Sized Fe-Cr-Al Alloy Powder
Charakterystyka porowatego korpusu spiekanego z nanometrycznego proszku stopu Fe-Cr-Al
Autorzy:
Lee, S.-I.
Lee, S.-H.
Gu, B.-U.
Lee, D.-W.
Kim, B.-K.
Powiązania:
https://bibliotekanauki.pl/articles/356635.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Fe-Cr-Al powder
metallic sponges
sintering temperature
oxidation resistance
proszek Fe-Cr-Al
proszek nanometryczny
temperatura spiekania
odporność na utlenianie
Opis:
Porous metal with uniform honeycomb structure was successfully produced by sintering using Fe-Cr-Al nano powder, which was prepared by the pulsed wire evaporation (PWE) in ethanol. Its process consisted of the several steps; 1) coating on the surface of polyurethane sponge with the liquid droplets generated from the ethanol-based slurry where the Fe-Cr-Al nano powders were uniformly dispersed, 2) heat treatment of debinding to remove the polyurethane sponge and 3) sintering of the porous green body formed by Fe-Cr-Al nano powders. The strut thickness of porous Fe-Cr-Al was increased by the increase of spraying times in ESP step. Also, The shrinkages and the oxidation resistance of the sintered porous body was increased with increase of sintering temperature. The optimal sintering temperature was shown to 1450°C in views to maximize the oxidation resistance and sinterability.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1275-1279
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Studies on the effect of coal particle size on biodepyritization of high sulfur coal in batch bioreactor
Autorzy:
Singh, S.
Srichandan, H.
Pathak, A.
Gahan, Ch. S.
Lee, S.
Kim, D. J.
Kim, B. G.
Powiązania:
https://bibliotekanauki.pl/articles/778523.pdf
Data publikacji:
2015
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
biodepyritization
coal
pyrite
stirred tank bioreactor
Opis:
The moderate thermophilic mix culture bacteria were used to depyritize the Illinois coal of varying particle sizes (-100 μm, 100-200 μm, +200 μm). Mineral libration analysis showed the presence of pyrite along with other minerals in coal. Microbial depyritization of coal was carried out in stirred tank batch reactors in presence of an iron-free 9K medium. The results indicate that microbial depyritization of coal using moderate thermophiles is an efficient process. Moreover, particle size of coal is an important parameter which affects the efficiency of microbial depyritization process. At the end of the experiment, a maximum of 75% pyrite and 66% of pyritic sulphur were removed from the median particle size. The XRD analysis showed the absence of pyrite mineral in the treated coal sample. A good mass balance was also obtained with net loss of mass ranging from 5-9% showing the feasibility of the process for large scale applications.
Źródło:
Polish Journal of Chemical Technology; 2015, 17, 1; 97-102
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Ga2O3 Nanoparticles Dispersion on Microstructure and Thermoelectric Properties of p-Type BiSbTe Based Alloys
Autorzy:
Kim, E.-B.
Koo, J.-M.
Hong, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/351366.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
thermoelectric properties
Bi0.5Sb1.5Te3 alloys
Seebeck coefficient
mechanical alloying
spark plasma sintering
Opis:
In this study, p-type Bi0.5Sb1.5Te3 based nanocomposites with addition of different weight percentages of Ga2O3 nanoparticles are fabricated by mechanical milling and spark plasma sintering. The fracture surfaces of all Bi0.5Sb1.5Te3 nanocomposites exhibited similar grain distribution on the entire fracture surface. The Vickers hardness is improved for the Bi0.5Sb1.5Te3 nanocomposites with 6 wt% added Ga2O3 due to exhibiting fine microstructure, and dispersion strengthening mechanism. The Seebeck coefficient of Bi0.5Sb1.5Te3 nanocomposites are significantly improved owing to the decrease in carrier concentration. The electrical conductivity is decreased rapidly upon the addition of Ga2O3 nanoparticle due to increasing carrier scattering at newly formed interfaces. The peak power factor of 3.24 W/mK2 is achieved for the base Bi0.5Sb1.5Te3 sintered bulk. TheBi0.5Sb1.5Te3 nanocomposites show low power factor than base sample due to low electrical conductivity.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 993-997
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure Development of Spark Plasma Sintered Ti-Nb Alloy by Heat Treatment
Autorzy:
Haq, M. A.
Abbas, S. F.
Eom, N. S. A.
Kim, T. S.
Lee, B.
Park, K.-T.
Kim, B. S.
Powiązania:
https://bibliotekanauki.pl/articles/355593.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
TiNb alloy
Spark plasma sintering
Heat treatment
Microstructure
β-phase titanium
Opis:
The β-phase Titanium (β-Ti) alloys have been under the spotlight in the recent past for their use as biomedical prosthetic materials owing to their excellent properties such as low elastic modulus, high corrosion resistance and tensile strength. Recently, Niobium (Nb) has gained a lot of attention as a β-phase stabilizing element in Ti alloys to replace Vanadium (V) due to its excellent solubility in Ti, low elastic modulus and biocompatibility. In this work, low cost Ti-20Nb binary alloy has been fabricated via powder metallurgy procedures. The blended powder mixtures of Ti and Nb were sintered at 900°C for 20 mins by the Spark Plasma Sintering (SPS) with an applied uniaxial pressure of 40 MPa. The heating rate was fixed at 50°C/min. The sintered alloy was subject to heat treatments at 1200°C in vacuum condition for various time durations. The characterizations of microstructure obtained during this process were done using FE-SEM, EDS and XRD. By increasing heat treatment time, as understood, the volume of residual Nb particles was decreased resulting in accelerated diffusion of Nb into Ti. Micro hardness of the alloy increased from 340 to 355 HV with the increase in β phase content from 30 to 45%. The resultant alloys had relatively high densities and homogenized microstructures of dispersed lamellar β grains in α matrix.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1429-1432
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication and Characterization of CoCrFeNiMn High Entropy Alloy Powder Processed by Gas Atomization
Autorzy:
Park, T. G.
Lee, S. H.
Lee, B.
Cho, H. M.
Choi, W. J.
Kim, B. S.
Shin, K. S.
Kim, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353649.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high entropy alloy
gas atomization
spark plasma sintering
CoCrFeNiMn
Opis:
In this study, precisely controlled large scale gas atomization process was applied to produce spherical and uniform shaped high entropy alloy powder. The gas atomization process was carried out to fabricate CoCrFeNiMn alloy, which was studied for high ductility and mechanical properties at low temperatures. It was confirmed that the mass scale, single phase, equiatomic, and high purity spherical high entropy alloy powder was produced by gas atomization process. The powder was sintered by spark plasma sintering process with various sintering conditions, and mechanical properties were characterized. Through this research, we have developed a mass production process of high quality and spherical high entropy alloy powder, and it is expected to expand applications of this high entropy alloy into fields such as powder injection molding and 3D printing for complex shaped components.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 2; 1055-1059
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Multistep Heat-Treatment Effects on Electrospun Nd-Fe-B-O Nanofibers
Autorzy:
Jeon, E. J.
Eom, N. S. A.
Lee, J.
Lee, B.
Cho, H. M.
On, J. S.
Choa, Y.-H
Kim, B. S.
Powiązania:
https://bibliotekanauki.pl/articles/354311.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B
nanofibers
electrospinning
heat treatment
Opis:
Neodymium-Iron-Boron (Nd-Fe-B) magnets are considered to have the highest energy density, and their applications include electric motors, generators, hard disc drives, and MRI. It is well known that a fiber structure with a high aspect ratio and the large specific surface area has the potential to overcome the limitations, such as inhomogeneous structures and the difficulty in alignment of easy axis, associated with such magnets obtained by conventional methods. I n this work, a suitable heat-treatment procedure based on single-step and multistep treatments to synthesize sound electrospun Nd-Fe-B-O nanofibers of Φ572 nm was investigated. The single-step heat-treated (directly heat-treated at 800°C for 2 h in air) samples disintegrated along with the residual organic compounds, whereas the multistep heat-treated (sequential three-step heat-treated including three steps;: dehydration (250°C for 30 min in an inert atmosphere), debinding (650°C for 30 min in air), and calcination (800°C for 1 h in air)) fibers maintained sound fibrous morphology without any organic impurities. They could maintain such fibrous morphologies during the dehydration and debinding steps because of the relatively low internal pressures of water vapor and polymer, respectively. In addition, the NdFeO3 alloying phase was dominant in the multistep heat-treated fibers due to the removal of barriers to mass transfer in the interparticles.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1433-1437
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies