Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Jakubiuk, P." wg kryterium: Autor


Wyświetlanie 1-11 z 11
Tytuł:
Skaryfikacja a wartość siewna nasion rutwicy wschodniej (Galega orientalis Lam.)
Autorzy:
Tworkowski, J.
Szczukowski, S.
Jakubiuk, P.
Powiązania:
https://bibliotekanauki.pl/articles/810579.pdf
Data publikacji:
1999
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Opis:
Nasiona rutwicy wschodniej Galega orientalis Lam. zebrane ręcznie z plantacji poddano skaryfikacji kilkoma sposobami i oceniono ich wartość siewną. Próby nasion bez skaryfikacji zawierały około 85% nasion twardych, kiełkowały i wschodziły w polu zdecydowanie słabiej od nasion skaryfikowanych. Najwyższą laboratoryjną szybkością i zdolnością kiełkowania oraz najliczniejszymi wschodami w polu wykazały się nasiona traktowane przez 15 minut stężonym kwasem siarkowym. Przedłużenie czasu działania kwasu na nasiona do 30, 45 i 60 minut powodowało ograniczenie liczby wschodzących roślin w polu. Nasiona zanurzane na 30, 60 i 90 sekund w ciekłym azocie charakteryzowały się słabszą szybkością kiełkowania i mniej licznymi wschodami w polu od nasion skaryfikowanych w kwasie siarkowym. Dwukrotna skaryfikacja mechaniczna zwiększała szybkość i zdolność kiełkowania nasion w laboratorium, jednak po wysiewie w polu wschody z tych nasion nie byty liczniejsze od otrzymanych z nasion skaryfikowanych jeden raz. Wszystkie sposoby skaryfikacji obniżały masę 1000 nasion. Elektroprzewodnictwo wód nastoinowych oraz ilość pobranej wody przez nasiona w czasie 24 godzin były wprost proporcjonalne do wartości siewnej ocenianych nasion.
The seeds of Galega orientalis Lam. harvested by hands were subjected to clipping by several methods and their sowing value was determined. Seed samples without clipping contained ca. 85% hard non-germinating seeds, germinated less intensively and their field emergence rate was lower than that for treated seeds. The highest energy and capacity of germination in the laboratory as well as the best field emergence were found in seeds treated for 15 min with concentrated sulfuric acid: treatment prolonged to 30, 45 and 60 min reduced the number of emerged seedlings in the field. Seeds submerged for 30, 60 or 90 seconds in liquid nitrogen showed lower germination energy and lower field emergence rate as compared to seeds treated with sulfuric acid. Doubled mechanical clipping resulted in increase of germination capacity and energy under laboratory conditions whereas the same emergence rate as for single treatment was found in the field. All methods of seed treatment reduced 1000 seed weight. Electroconductivity of excudates and amount of water imbibed during 24 hours were proportional to seed sowing value.
Źródło:
Zeszyty Problemowe Postępów Nauk Rolniczych; 1999, 468
0084-5477
Pojawia się w:
Zeszyty Problemowe Postępów Nauk Rolniczych
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Koaksjalny magnetokumulacyjny generator prądu
Coaxial magnetocumulative power generator
Autorzy:
Wołoszyn, M.
Jakubiuk, K.
Zimny, P.
Powiązania:
https://bibliotekanauki.pl/articles/378119.pdf
Data publikacji:
2016
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
magnetokumulacja
generator prądu
detonacja
Opis:
W pracy przedstawiono wyniki symulacji komputerowej koaksjalnego magnetokumulacyjnego generatora prądu (MGP). Badania symulacyjne przeprowadzono dla różnych wartości średnicy wewnętrznej, długości i prędkości odkształcania elementu MGP.
The results of computer simulation of the coaxial magnetocumulative current generator (MGP) were presented in this paper. The simulation tests were carried out for different values of internal diameter, length and speed of the deformation of an MGP element.
Źródło:
Poznan University of Technology Academic Journals. Electrical Engineering; 2016, 85; 53-59
1897-0737
Pojawia się w:
Poznan University of Technology Academic Journals. Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Masking of ferromagnetic ellipsoidal shell in Earth’s magnetic field
Autorzy:
Jakubiuk, K.
Wołoszyn, M.
Zimny, P.
Powiązania:
https://bibliotekanauki.pl/articles/97594.pdf
Data publikacji:
2013
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
mathematical models of magnetic field
magnetization of ferromagnetic object
masking of ferromagnetic object
windings for demagnetization of the ship
Opis:
A ferromagnetic object, located in the Earth’s magnetic field, changes the distribution of that field. By measuring such disturbances it is possible to detect the object and destroy it. To conceal the object, a special winding is placed inside its ferromagnetic shell, which function is to eliminate the disturbances in the distribution of the Earth’s magnetic field. A thin walled ellipsoidal shell made of ferromagnetic material are examined as the object model. Coils are placed inside the shell and their function is to generate a magnetic field, which eliminates the effect the shell makes on the distribution of the Earth’s magnetic field in the surrounding area. Such a procedure is called magnetic masking and the winding used for this purpose is called the masking winding. The possibility of building the masking windings for the ferromagnetic ellipsoidal shell, situated in a magnetic field transverse in relation to its major axis, is also examined. Masking of a thin-walled ellipsoidal ferromagnetic object located in the longitudinal magnetic field is described in the article [1]. Investigating the possibility of masking of objects in a transverse magnetic field presented in this article will allow for a comprehensive assessment of a possibility of masking thin walled ferromagnetic objects of elongated ellipsoidal shape. The solution of Maxwell’s equations, which describe the magnetic field distribution caused by the ferromagnetic shell presence in the Earth’s magnetic field, are applied. Furthermore, the ability of selecting coils, which fully eliminate the perturbations of the magnetic field outside the shell are proven.
Źródło:
Computer Applications in Electrical Engineering; 2013, 11; 92-99
1508-4248
Pojawia się w:
Computer Applications in Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Multisource model of ship electric field
Autorzy:
Jakubiuk, K.
Zimny, P.
Wołoszyn, M.
Powiązania:
https://bibliotekanauki.pl/articles/97439.pdf
Data publikacji:
2011
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
magnetic field of the ship
mine protection
BEM
Opis:
A steel-hulled ship in sea water produces an electric field around itself. The source of this field are electrochemical processes and ship’s cathodic protection. The analysis of the electric field around the ship is important by the reason of the ship’s identification and counter-mine protection. The paper presents a simplified model of the ship’s multisource electric field, which allows to calculate the electric field distribution in the so-called distant zone around the ship in an approximate way using a PC, during time lasting from few up to several dozen of minutes.
Źródło:
Computer Applications in Electrical Engineering; 2011, 9; 78-84
1508-4248
Pojawia się w:
Computer Applications in Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania nad technologią wytwarzania materiałów podsadzkowych (propantów) stosowanych przy wydobyciu gazu łupkowego. Cz.3 – Otrzymywanie propantów poprzez suszenie zawiesiny w suszarni rozpyłowej
Research on production technology of proppants used in shale gas extraction. Part 3 – Preparation of proppants by suspension drying in spray dryer
Autorzy:
Jakubiuk, T.
Łosiewicz, A.
Taźbierski, P.
Powiązania:
https://bibliotekanauki.pl/articles/392211.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Ceramiki i Materiałów Budowlanych
Tematy:
gaz łupkowy
wydobycie
materiał podsadzkowy
technologia wytwarzania
suszarnia rozpyłowa
granulat
shale gas
extraction
proppant
production technology
spray dryer
granulate
Opis:
Do prób otrzymywania materiału podsadzkowego poprzez suszenie zawiesiny wodnej ujednorodnionych surowców mineralnych wykorzystano suszarnię rozpyłową D 20. Skład surowcowy zawiesiny ustalono po przeprowadzeniu badań właściwości fizykochemicznych wypalonych zestawów surowcowych wykonanych w skali mikro. Badano temperaturę spiekania, gęstość, porowatość, wytrzymałość mechaniczną i odporność chemiczną. Do sporządzenia zestawów jako surowiec podstawowy wykorzystano odpady powstające w elektrociepłowniach warszawskich, które domieszkowano glinami „Janina” i „Zapniów”. Badania poszczególnych właściwości prowadzono na beleczkach prasowanych pod niskim ciśnieniem w laboratoryjnej prasie hydraulicznej i wypalanych w piecu elektrycznym. Do prasowania próbek badawczych wykorzystywano granulat otrzymywany ręcznie poprzez posługiwanie się sitem. W oparciu o recepturę zestawu, który charakteryzował się niską temperaturą spiekania, dużą wytrzymałością i odpornością chemiczną, sporządzono zawiesinę do suszenia rozpyłowego. Podczas suszenia tak dobierano reologię zawiesiny i parametry suszenia, aby otrzymać maksymalną ilość granulatu w przedziale 0,2–0,7 mm. Otrzymany granulat wypalono w piecu rurowym w ustalonej wcześniej temperaturze spiekania i przekazano do Instytutu Nafty i Gazu w celu zbadania przydatności do wykorzystania go jako materiał podsadzkowy.
The proppants were prepared by drying aqueous suspension of homogenous mineral material in spray dryer-D 20. The composition of raw materials was determined by conducting physicochemical test of fired specimen in a laboratory scale. Sintering temperature, density, porosity, mechanical strength and chemical resistance were investigated. Waste from Warsaw Power Plants with addition of „Janina” and „Zapniów” clays were used for preparation of specimen sets. Individual properties were determined on specimens pressed at law pressure in a laboratory hydraulic press and fired in an electric furnace. Test specimens were prepared from granulate sieved manually and pressed. Based on row materials composition, which showed low sintering temperature, high strength and high chemical resistance, a suspension for spray drying was prepared. During the drying process, both the rheology of the suspension and drying parameters, were being chosen so as to obtain the maximum amount of granulate in the range of 0,2–0,7 mm grain size. The final granulate was fired in a tube furnace at a predetermined sintering temperature and delivered to the Institute of Oil and Gas in order to investigate the suitability for use as a proppants.
Źródło:
Prace Instytutu Ceramiki i Materiałów Budowlanych; 2015, R. 8, nr 23, 23; 39-48
1899-3230
Pojawia się w:
Prace Instytutu Ceramiki i Materiałów Budowlanych
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wykorzystanie odpadów komunalnych do wytwarzania katalizatorów ceramicznych
Utilization of communal waste for ceramic catalyst production
Autorzy:
Jakubiuk, T.
Łosiewicz, A.
Taźbierski, P.
Powiązania:
https://bibliotekanauki.pl/articles/392304.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Ceramiki i Materiałów Budowlanych
Tematy:
odpad komunalny
wykorzystanie odpadów
katalizator ceramiczny
odpad poliolefinowy
kraking
municipal waste
waste recycling
ceramic catalyst
polyolephin wastes
cracking
Opis:
W artykule przedstawiono prace prowadzone w Instytucie Ceramiki i Materiałów Budowlanych nad wykorzystaniem odpadów powstających w Zakładach Utylizacji Stałych Odpadów Komunalnych w Warszawie do wytworzenia katalizatora termicznego krakingu odpadów z tworzyw sztucznych do produktów ciekłych w temperaturze otoczenia. Opisano sposób prowadzenia prac nad wytworzeniem i badaniem właściwości katalitycznych otrzymanego materiału ceramicznego. Właściwości fizykochemiczne i katalityczne tworzywa ceramicznego porównywano z katalizatorem kordierytowym wytworzonym w Instytucie dla firmy Altris i z powodzeniem użytkowanym w urządzeniach przemysłowych katalitycznego rozkładu odpadów polietylenowych i polipropylenowych.
Article presents research conducted in Institute of Ceramics and Building Materials concerning waste utilization produced in Warsaw Solid Communal Waste Utilisation Plant to make thermal cracking waste catalyst from plastics to liquid products in ambient temperature. The procedure methods of making and testing catalytic properties of obtained ceramic material has been described. The physical-chemical and catalytic properties of ceramic material have been compared with cordierite catalytic made in Institute for Altric company and with success used in industrial machines for catalytic decomposition polythene and polypropylene waste.
Źródło:
Prace Instytutu Ceramiki i Materiałów Budowlanych; 2012, R. 5, nr 9, 9; 78-88
1899-3230
Pojawia się w:
Prace Instytutu Ceramiki i Materiałów Budowlanych
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Perturbation analysis of electric field around objects in sea water
Autorzy:
Jakubiuk, K.
Zimny, P.
Wołoszyn, M.
Powiązania:
https://bibliotekanauki.pl/articles/377479.pdf
Data publikacji:
2012
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
electric field
object in sea water
location methods
electric perturbations
Opis:
In marine environment there are different types of objects, such as ships or naval mines, which should be located and identified. One of the location methods is based on the electric potential distribution measurement [1, 2], The object with an insulating or conductive casing, placed in an electric field, causes some field perturbations. For the purpose of the object location the dimensions of the area, where it is possible to determine electric field perturbations by measurement, are important. In this way one can pre-determine the extent of the system for locating and identifying objects placed in the seawater. This paper presents an analytical approach to the perturbation analysis of electric field distribution caused by a sphere and an ellipsoid placed in a uniform electric field. The distance, beyond which the uniform electric perturbations can be neglected, is determined.
Źródło:
Poznan University of Technology Academic Journals. Electrical Engineering; 2012, 69; 81-88
1897-0737
Pojawia się w:
Poznan University of Technology Academic Journals. Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Making of ferromagnetic elliptical shell in transverse magnetic field
Autorzy:
Jakubiuk, K.
Wołoszyn, M.
Zimny, P.
Powiązania:
https://bibliotekanauki.pl/articles/377889.pdf
Data publikacji:
2013
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
ferromagnetic object
magnetic field
ferromagnetic shell
Opis:
A ferromagnetic object, located in the Earth’s magnetic field, changes its distribution. Through measuring such disturbances, one can locate the object and destroy it. To conceal the object, a special winding is placed inside its ferromagnetic shell, and its task is to eliminate the disturbances in the distribution of the Earth’s magnetic field. A thin walled elliptical shell, made of ferromagnetic material, is examined as the object model. There are coils, placed inside the shell, and their task is to generate a magnetic field, which is eliminating the effect, the shell is making on the distribution of the Earth’s magnetic field in the surrounding area. Such a procedure is called magnetic masking and the winding used for this purpose is called the masking winding. The possibility of building the masking windings for the ferromagnetic elliptical shell, situated in a transverse magnetic field respectively to its major axis, is also examined. The solution of Maxwell’s equations, which are describing the magnetic field distribution caused by the ferromagnetic shell presence in the Earth’s magnetic field, is found. Furthermore, the ability of selecting coils, which are eliminating the perturbations of the magnetic field outside the shell completely, is proven.
Źródło:
Poznan University of Technology Academic Journals. Electrical Engineering; 2013, 73; 131-136
1897-0737
Pojawia się w:
Poznan University of Technology Academic Journals. Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The method of location and identification of weak electric field source in seawater
Autorzy:
Jakubiuk, K.
Zimny, P.
Wołoszyn, M.
Powiązania:
https://bibliotekanauki.pl/articles/376626.pdf
Data publikacji:
2012
Wydawca:
Politechnika Poznańska. Wydawnictwo Politechniki Poznańskiej
Tematy:
electric field
object location
object identification
seawater
Opis:
There are electrochemical processes occurring on a metal object surface in seawater. As the result of these processes, one can observe an electric field in the object vicinity. The paper presents the method and measurement system that allows to locate the detected object and to identify parameters of its simplified model in form of a current dipole. The identify method is based on the matrix norm minimization. The matrix contains results of measurements and parameters of the object in request taken as the current dipole. The results of simulation and experimental detection of sea mines are given. The research results confirmed the effectiveness of the developed method.
Źródło:
Poznan University of Technology Academic Journals. Electrical Engineering; 2012, 69; 103-109
1897-0737
Pojawia się w:
Poznan University of Technology Academic Journals. Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Metoda obniżenia temperatury spiekania tworzyw alundowych zawierających powyżej 90% Al2O3
Method of lowering the sintering temperature of the alumina materials containing more than 90% Al2O3
Autorzy:
Jakubiuk, T.
Łosiewicz, A.
Taźbierski, P.
Powiązania:
https://bibliotekanauki.pl/articles/168117.pdf
Data publikacji:
2014
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Ceramiki i Materiałów Budowlanych
Tematy:
tworzywa alundowe
temperatura spiekania
modyfikatory
corundum material
sintering temperature
modifiers
Opis:
W artykule przedstawiono prace prowadzone w Instytucie Ceramiki i Materiałów Budowlanych nad obniżeniem temperatury spiekania tworzywa alundowego zawierającego 93% wagowych Al2O3, wykorzystywanego do produkcji mielników ceramicznych i wykładzin odpornych na ścieranie stosowanych w młynach kulowych i liniach przesyłowych transportu pneumatycznego. Przedstawiono sposób prowadzenia prac nad wytworzeniem, ustaleniem temperatury spiekania i badaniem właściwości otrzymanych materiałów ceramicznych. Właściwości te odnoszono do próbek formowanych z tworzywa wzorcowego Al93.
The paper describes work carried out at the Institute of Ceramics and Building Materials on lowering the sintering temperature alumina material containing 93 wt% Al2O3, used for the production of ceramic grinding media and wear resistant linings used in ball mills and transmission lines of pneumatic transport systems. The way of conducting work on developing, fixing and testing the sintering temperature properties of the ceramic materials were presented. Obtained properties were compared to samples made of referenced material Al93.
Źródło:
Szkło i Ceramika; 2014, R. 65, nr 2, 2; 10-12
0039-8144
Pojawia się w:
Szkło i Ceramika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparative analysis of coaxial magnetocumulative generators
Autorzy:
Wołoszyn, M.
Jakubiuk, K.
Zimny, P.
Kowalak, D.
Powiązania:
https://bibliotekanauki.pl/articles/141467.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
coaxial generator
magnetic field
magnetocumulative generator
Opis:
This paper presents the results of a computer simulation of coaxial magnetocumulative current generators (MCGs). The simulation tests were carried out for different values of the internal diameter, length and speed of the deformation of the MGP element.
Źródło:
Archives of Electrical Engineering; 2017, 66, 4; 681-692
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-11 z 11

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies