Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Grabarczyk, M" wg kryterium: Autor


Tytuł:
Single-piece all-solid-state Co(II) ion-selective electrode for cobalt monitoring in real samples
Autorzy:
Wardak, C.
Grabarczyk, M.
Powiązania:
https://bibliotekanauki.pl/articles/2082867.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
cobalt(II) ion-selective electrode
ionic liquids
solid contact
potentiometry
Opis:
A novel single-piece all-solid-state ion-selective electrode for Co2+ determination has been prepared. The PVC membrane was modified by the addition of ionic liquid. The effect of various ionic liquids was studied in detail and improved performance was observed. The best performance exhibited by the electrode was achieved with a membrane containing 1-ethyl- 3-methyl imidazolium chloride, having a slope of 31.8 mV/ decade in a wide concentration range of 1×10-7 – 1×x10-1 mol L-1. The limit of detection was 5.6×10-8 mol L-1. The response time of the proposed sensor was less than 10 s and the lifetime was at least three months. The proposed sensor showed good selectivity towards the Co2+ ion in comparison with some alkali, alkaline earth, transition and heavy metal ions. It was successfully applied for the direct determination of cobalt ions in real sample solution.
Źródło:
International Agrophysics; 2020, 34, 1; 17-24
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Selection of Hardening Technology of Moulding Sand with Hydrated Sodium Silicate Binder Devoted to Aluminum Alloys Ablation Casting
Autorzy:
Major-Gabryś, K.
Hosadyna-Kondracka, M.
Grabarczyk, A.
Kamińska, J.
Powiązania:
https://bibliotekanauki.pl/articles/354196.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
foundry engineering
ablation casting
moulding sands
hydrated sodium silicate
hot-box technology
Opis:
The ablation casting technology consists in pouring castings in single-use moulds made from the mixture of sand and watersoluble binder. After pouring the mould with liquid metal, while the casting is still solidifying, the mould destruction (washing out, erosion) takes place using a stream of cooling medium, which in this case is water. The following paper focuses on the selection of moulding sands with hydrated sodium silicate technologies for moulds devoted to the ablation casting of aluminum alloys. It has been proposed to use different types of moulding sands with a water-soluble binder, which is hydrated sodium silicate. The authors showed that the best kind of moulding sands for moulds for Al alloy casting will be moulding sands hardened with physical factors – through dehydration. The use of microwave hardened moulding sands and moulding sands made in hot-box technology has been proposed. The tests were carried out on moulding sands with different types of modified binder and various inorganic additives. The paper compares viscosity of different binders used in the research and thermal degradation of moulding sands with tested binders. The paper analyzes the influence of hardening time periods on bending strength of moulding sands with hydrated sodium silicate prepared in hot-box technology. The analysis of literature data and own research have shown that molding sand with hydrated sodium silicate hardened by dehydration is characterized by sufficient strength properties for the ablation foundry of Al alloys.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 1; 359-364
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Simple, responsive and cost effective simultaneous quantification of Ga(III) and In(III) in environmental water samples
Autorzy:
Grabarczyk, M.
Adamczyk, M.
Powiązania:
https://bibliotekanauki.pl/articles/2082480.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
gallium(III)
indium(III)
trace analysis
environmental
water samples
Opis:
The simultaneous determination of Ga(III) and In(III) in environmental water samples was described. The procedure was based on adsorptive stripping voltammetry using an in situ plated bismuth film electrode as a working electrode. In order to obtain low detection limits and satisfactory separations of gallium and indium peaks on the voltammogram, cupferron was used as a complexing agent. The optimum composition of the supporting electrolyte was found to be: 0.1 mol l-1 acetate buffer (pH=5.0), 2 × 10-4 mol l-1 cupferron, 2 × 10-4 mol l-1 Bi(III), optimal voltammetric parameters were found to be: accumulation potential -0.9 V, accumulation time 60 s. The linear range of Ga(III) as well as In(III) was observed over a concentration range from 2.5 × 10-8 mol l-1 to 1.5 × 10-6 mol l-1. The method was satisfactorily applied to the simultaneous quantification of gallium and indium in environmental water samples. This facilitated a promising application of the recommended procedure for monitoring the environment, which is necessary to evaluate the soil-plant system.
Źródło:
International Agrophysics; 2019, 33, 2; 161-166
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Moulding Sand Type on Mechanical and Thermal Deformation
Autorzy:
Grabarczyk, A.
Major-Gabryś, K.
Dobosz, S. M.
Jakubski, J.
Bolibruchová, D.
Brůna, M.
Pastirčák, R.
Powiązania:
https://bibliotekanauki.pl/articles/353843.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
foundry engineering
moulding sand
core sand
organic binder
inorganic binder
mechanical deformation
thermal deformation
Opis:
Casting industry has been enriched with the processes of mechanization and automation in production. They offer both better working standards, faster and more accurate production, but also have begun to generate new opportunities for new foundry defects. This work discusses the disadvantages of processes that can occur, to a limited extend, in the technologies associated with mould assembly and during the initial stages of pouring. These defects will be described in detail in the further part of the paper and are mainly related to the quality of foundry cores, therefore the discussion of these issues will mainly concern core moulding sands. Four different types of moulding mixtures were used in the research, representing the most popular chemically bonded moulding sands used in foundry practise. The main focus of this article is the analysis of the influence of the binder type on mechanical and thermal deformation in moulding sands.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 1; 347-351
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
3D bioprinting – determination of hydrogel bioinks properties for a printer with dedicated construction
Autorzy:
Bociąga, D.
Grabarczyk, J.
Sobczyk-Guzenda, A.
Bartniak, M.
Przybyszewska, K.
Powiązania:
https://bibliotekanauki.pl/articles/285589.pdf
Data publikacji:
2018
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Polskie Towarzystwo Biominerałów
Tematy:
hydrogels
biofabrication technology
bioinks
Źródło:
Engineering of Biomaterials; 2018, 21, 148; 90
1429-7248
Pojawia się w:
Engineering of Biomaterials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Assessment of mechanical and biological properties of sodium alginate/gelatine hydrogels dedicated for bioprinting prepared with the use of various solvents
Autorzy:
Przybyszewska, K.
Bartniak, M.
Sobczyk-Guzenda, A.
Grabarczyk, J.
Bociąga, D.
Powiązania:
https://bibliotekanauki.pl/articles/286245.pdf
Data publikacji:
2018
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Polskie Towarzystwo Biominerałów
Tematy:
hydrogels
bioprinting
biological properties
Źródło:
Engineering of Biomaterials; 2018, 21, 148; 91
1429-7248
Pojawia się w:
Engineering of Biomaterials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Measurement of Molding Sand Elasticity
Autorzy:
Major-Gabryś, K.
Grabarczyk, A.
Dobosz, S.M.
Jakubski, J.
Morek, J.
Beňo, J.
Powiązania:
https://bibliotekanauki.pl/articles/106977.pdf
Data publikacji:
2018
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
molding sands
mechanical deformation
elasticity
hot-distortion
Opis:
The progressive mechanization and automation of industrial equipment is the driving force of progress, not only in the field of production but also in the measuring and control equipment. In mold production, the automation of processes such as forming molds and cores along with their assembly has led to increases in serial production, reductions in defects, and the shortening of molding times, among others. Thanks to automation in mold and core departments and the use of all sorts of manipulators, mold production in foundries has gained momentum. Unfortunately, in addition to the mentioned advantages, there are also new challenges as to the quality and properties of the molding and core sands used in highly automated foundries.This article presents recent research on molding sand elasticity. The topic was introduced as an attempt to answer the new needs of highly mechanized foundries. The article discusses a new method of measuring the resistance of molding materials to undergoing mechanical deformation (molding sand elasticity), with an additional analysis of the bending strengths of the tested samples. Precise measurements, test sample preparation, and interpretation of the received results are presented in the article.
Źródło:
Journal of Casting & Materials Engineering; 2018, 2, 2; 38-44
2543-9901
Pojawia się w:
Journal of Casting & Materials Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Mechanical and Thermal Deformation of Hot-box Moulding Sands
Autorzy:
Grabarczyk, A.
Major-Gabryś, K.
Dobosz, S. M.
Jakubski, J.
Powiązania:
https://bibliotekanauki.pl/articles/381390.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry material
innovative foundry technology
mechanical properties
moulding sand deformation
hot distortion
innowacyjny materiał odlewniczy
innowacyjna technologia odlewnicza
właściwości mechaniczne
odkształcenie masy formierskiej
deformacja cieplna
Opis:
The constantly developing and the broadly understood automation of production processes in foundry industry, creates both new working conditions - better working standards, faster and more accurate production - and new demands for previously used materials as well as opportunities to generate new foundry defects. Those high requirements create the need to develop further the existing elements of the casting production process. This work focuses on mechanical and thermal deformation of moulding sands prepared in hot-box technology. Moulding sands hardened in different time periods were tested immediately after hardening and after cooling. The obtained results showed that hardening time period in the range 30-120 sec does not influence the mechanical deformation of tested moulding sands significantly. Hot distortion tests proved that moulding sands prepared in hot-box technology can be characterized with stable thermal deformation up to the temperature of circa 320 °C.
Źródło:
Archives of Foundry Engineering; 2018, 18, 4; 55-58
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modification of Foundry Binders by Biodegradable Material
Autorzy:
Major-Gabryś, K.
Grabarczyk, A.
Dobosz, S. M.
Powiązania:
https://bibliotekanauki.pl/articles/380402.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
environmental protection
innovative foundry material
phenol-furfuryl resin
hydrated sodium silicate
biodegradable material
ochrona środowiska
innowacyjny materiał odlewniczy
uwodniony krzemian sodu
materiał biodegradowalny
Opis:
The paper presents the impact of biodegradable material - polycaprolactone (PCL) on selected properties of moulding sands. A self-hardening moulding sands with phenol-furfuryl resin, which is widely used in foundry practice, and an environmentally friendly self-hardening moulding sand with hydrated sodium silicate where chosen for testing. The purpose of the new additive in the case of synthetic resin moulding sands is to reduce their harmfulness to the environment and to increase their “elasticity” at ambient temperature. In the case of moulding sands with environmentally friendly hydrated sodium silicate binder, the task of the new additive is to increase the elasticity of the tested samples while preserving their ecological character. Studies have shown that the use of 5% PCL in moulding sand increases their flexibility at ambient temperature, both with organic and inorganic binders. The influence of the new additive on the deformation of the moulding sands at elevated temperatures has also been demonstrated.
Źródło:
Archives of Foundry Engineering; 2018, 18, 2; 31-34
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Moulding Sand with Inorganic Cordis Binder for Ablation Casting
Autorzy:
Hosadyna-Kondracka, M.
Major-Gabryś, K.
Kamińska, J.
Grabarczyk, A.
Angrecki, M.
Powiązania:
https://bibliotekanauki.pl/articles/382039.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technology
innovative foundry material
ablation casting
moulding sand
inorganic binder
thermal curing
innowacyjna technologia odlewnicza
innowacyjny materiał odlewniczy
odlewanie ablacyjne
masa formierska
spoiwo nieorganiczne
utwardzanie termiczne
Opis:
The essence of ablation casting technology consists in pouring castings in single-use moulds made from the mixture of sand and a water-soluble binder. After pouring the mould with liquid metal, while the casting is still solidifying, the mould destruction (washing out, erosion) takes place using a stream of cooling medium, which in this case is water. This paper focuses on the selection of moulding sands with hydrated sodium silicate for moulds used in the ablation casting. The research is based on the use of Cordis binder produced by the Hüttenes-Albertus Company. It is a new-generation inorganic binder based on hydrated sodium silicate. Its hardening takes place under the effect of high temperature. As part of the research, loose moulding mixtures based on the silica sand with different content of Cordis binder and special Anorgit additive were prepared. The reference material was sand mixture without the additive. The review of literature data and the results of own studies have shown that moulding sand with hydrated sodium silicate hardened by dehydration is characterized by sufficient strength properties to be used in the ablation casting process. Additionally, at the Foundry Research Institute in Krakow, preliminary semi-industrial tests were carried out on the use of Cordis sand technology in the manufacture of moulds for ablation casting. The possibility to use these sand mixtures has been confirmed in terms of both casting surface quality and sand reclamation.
Źródło:
Archives of Foundry Engineering; 2018, 18, 4; 110-115
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Tendency of Moulding Sands to Generate Core Cracks
Autorzy:
Grabarczyk, A.
Dobosz, S. M.
Kusiński, J.
Major-Gabryś, K.
Powiązania:
https://bibliotekanauki.pl/articles/380432.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technologies
innovative foundry materials
moulding sand
binder
elasticity
cracking
innowacyjne technologie odlewnicze
innowacyjne materiały odlewnicze
masa formierska
spoiwo
Opis:
The constant growth of foundry modernization, mechanization and automation is followed with growing requirements for the quality and parameters of both moulding and core sands. Due to this changes it is necessary to widen the requirements for the parameters used for their quality evaluation by widening the testing of the moulding and core sands with the measurement of their resistance to mechanical deformation (further called elasticity). Following article covers measurements of this parameter in chosen moulding and core sands with different types of binders. It focuses on the differences in elasticity, bending strength and type of bond destruction (adhesive/cohesive) between different mixtures, and its connection to the applied bonding agent. Moulding and cores sands on which the most focus is placed on are primarily the self-hardening moulding sands with organic and inorganic binders, belonging to the group of universal applications (used as both moulding and core sands) and mixtures used in cold-box technology.
Źródło:
Archives of Foundry Engineering; 2018, 18, 1; 157-161
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermally Hardened Moulding and Core Sands with Hydrated Sodium Silicate Designed for Al Alloy Castings
Autorzy:
Major-Gabryś, K. A.
Grabarczyk, A. P.
Dobosz, S. M.
Powiązania:
https://bibliotekanauki.pl/articles/379661.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technologies
innovative foundry materials
moulding sand
hydrated sodium silicate
thermal hardening
innowacyjne technologie odlewnicze
innowacyjne materiały odlewnicze
masa formierskia
krzemian sodu
hartowanie termiczne
Opis:
The necessity of obtaining high quality castings forces both researchers and producers to undertake research in the field of moulding sands. The key is to obtain moulding and core sands which will ensure relevant technological parameters along with high environmental standards. The most important group in this research constitutes of moulding sands with hydrated sodium silicate. The aim of the article is to propose optimized parameters of hardening process of moulding sands with hydrated sodium silicate prepared in warm-box technology. This work focuses on mechanical and thermal deformation of moulding sands with hydrated sodium silicate and inorganic additives prepared in warm-box technology. Tested moulding sands were hardened in the temperature of 140ºC for different time periods. Bending strength, thermal deformation and thermal degradation was tested. Chosen parameters were tested immediately after hardening and after 1h of cooling. Conducted research proved that it is possible to eliminate inorganic additives from moulding sands compositions. Moulding sands without additives have good enough strength properties and their economic and ecological character is improved.
Źródło:
Archives of Foundry Engineering; 2018, 18, 3; 132-137
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Elasticity of cores manufactured in cold box technology
Autorzy:
Dobosz, S. M.
Grabarczyk, A.
Major-Gabryś, K.
Bolibruchova, D.
Powiązania:
https://bibliotekanauki.pl/articles/355352.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
moulding sands
cold-box technology
elasticity of moulding sands
Opis:
In the foundry industry, as in many other fields we seek to achieve the best quality with the least losses and the lowest cost. To meet these demands numerous plants increased automatization of their manufacturing processes. However, with changes in the production process it is necessary to change also the materials used. Not only casting alloys that are used in production, but also applied moulding and core sands are important. Proper selection and evaluation of the properties of used moulding mixtures is crucial in order to achieve a highly efficient production. In this article a new issue concerning the use of flexibility in foundry molding and core was mentioned. It explains the principles of measurement and interpretation of the obtained results for the cold-box moulding sands.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 1; 351-354
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Elasticity of Moulding Sands – a Method of Reducing Core Cracking
Autorzy:
Dobosz, S. M.
Grabarczyk, A.
Major-Gabryś, K.
Powiązania:
https://bibliotekanauki.pl/articles/380966.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technologies
innovative foundry materials
moulding sand
binder
elasticity
cracking
innowacyjne technologie odlewnicze
innowacyjne materiały
piasek formierski
spoiwo
elastyczność
Opis:
This paper focuses on mechanical properties of self hardening moulding sands with furfuryl and alkyd binders. Elasticity as a new parameter of moulding sands is investigated. With the use of presented testing equipment it is possible to determine force kinetics and deformation of moulding sand in real time. The need for this kind of study comes from the modern casting industry. New foundries can be characterized with high intensity of production which is correlated with high level of mechanization and automatization of foundry processes. The increasingly common use of manipulators in production of moulds and cores can lead to generation of new types of flaws, caused by breakage in moulds and cores which could occur during mould assembly. Hence it is required that moulds and cores have high resistance to those kinds of factors, attributing it with the phenomenon of elasticity. The article describes the theoretical basis of this property, presents methods of measuring and continues earlier research.
Źródło:
Archives of Foundry Engineering; 2017, 17, 1; 31-36
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The thermal and structural analysis of new bicomponent binders for moulding sands consisting of furfuryl resin and polycaprolactone (PCL)
Autorzy:
Major-Gabryś, K.
Bobrowski, A.
Grabarczyk, A.
Dobosz, S. M.
Powiązania:
https://bibliotekanauki.pl/articles/355246.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technologies and materials
moulding sands
furfuryl resin
polycaprolactone
spectroscopic studies
PCL
FTIR
Opis:
The aim of the article is thermal and structural analysis of new two-component binders for foundry moulding sands. The previous research showed the possibility of using biodegradable materials as binders or parts of binders’ compositions for foundry moulding and core sands. This paper is concentrated on estimating the influence of PCL on phenol-furfuryl resin thermal destruction (measured by derivatographic research) and its structure (measured by FTiR technology). The research proved that addition of new biodegradable additive PCL in the amount of 5-15% to the phenol-furfuryl resin doesn’t change the resin thermal destruction course but it results in appearance of a new band in two-component binder structure. What’s more there has been noticed a growth of intensity for band at wavenumber 1730 cm-1 (C = O) with the increasing addition of PCL.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 1; 369-372
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies