Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Gawryluk, Jaroslaw" wg kryterium: Autor


Wyświetlanie 1-5 z 5
Tytuł:
The Effect of Fiber Arrangement in the Bio-Laminate and Geometric Parameters on the Stability of Thin-Walled Angle Column Under Axial Compression
Autorzy:
Gawryluk, Jarosław
Powiązania:
https://bibliotekanauki.pl/articles/2201861.pdf
Data publikacji:
2023
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
bio-laminates
flax
buckling analysis
L-profile
numerical case
Opis:
The aim of this study is to check how the change fiber configuration and geometric parameters affect the stability of a thin-walled angle column under compression. Buckling analysis of thin-walled structures made of bio-laminates was presented. Short angles with different configurations of reinforcing fibers and geometric parameters were studied. The laminate under analysis had a matrix made of epoxy resin reinforced with unidirectional flax fibers. The axially compressed structures were simply supported on both ends. Detailed numerical analyses were conducted by the finite element method using Abaqus software. The lowest two bifurcation loads and their corresponding eigenmodes were determined. Several configurations of unidirectional fiber arrangement with different width and length were tested. Results showed that the bio-laminate fiber configuration had a significant effect on the behavior of the compressed structure. Moreover, the change of geometrical parameters significantly influences the stability of the structure. In general, it was found that the bifurcation load decreased with the increase of the length of the L-profile column. However, increasing the flange width of the column resulted in a reduction of the bifurcation load (applies to a column with a length of 300 mm and longer). In paper the first stage of research is presented, which will be experimentally verified in subsequent studies.
Źródło:
Advances in Science and Technology. Research Journal; 2023, 17, 1; 150--159
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Stability of the thin-walled angle column made of bio-laminate versus glass-laminate under axial compression – numerical study
Autorzy:
Gawryluk, Jarosław
Powiązania:
https://bibliotekanauki.pl/articles/27309877.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czasopisma i Monografie PAN
Tematy:
bio-laminates
buckling
thin-walled structures
FEM
eigenproblem
biolaminat
wyboczenie
konstrukcje cienkościenne
MES
problem własny
Opis:
The aim of this study was to determine how the change of glass laminate fibres to flax fibres will affect the stability of thin-walled angle columns. Numerical analyses were conducted by the finite element method. Short L-shaped columns with different configurations of reinforcing fibres and geometric parameters were tested. The axially compressed structures were simply supported on both ends. The lowest two bifurcation loads and their corresponding eigenmodes were determined. Several configurations of unidirectional fibre arrangement were tested. Moreover, the influence of a flange width change by ±100% and a column length change by ±33% on the bifurcation load of the compressed structure was determined. It was found that glass laminate could be successfully replaced with a bio-laminate with flax fibres. Similar results were obtained for both materials. For the same configuration of fibre arrangement, the flax laminate showed a lower sensitivity to the change in flange width than the glass material. However, the flax laminate column showed a greater sensitivity to changes in length than the glass laminate one. In a follow-up study, selected configurations will be tested experimentally.
Źródło:
Archive of Mechanical Engineering; 2023, LXX, 1; 43--61
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental and finite element analysis of PPF controller effectiveness in composite beam vibration suppression
Autorzy:
Mitura, Andrzej
Gawryluk, Jaroslaw
Powiązania:
https://bibliotekanauki.pl/articles/2172029.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
finite element method
positive position feedback control
composite structures
hysteresis
phenomenon
macro-fiber composite
Opis:
In this paper the problem of vibration reduction is considered. Generally, mechanical vibrations occurring during the operation of a system are undesirable and may have a negative effect on its reliability. A finite element model of a single active blade is developed using the Abaqus software. This structure consists of a multi-layer glass-epoxy composite beam with an embedded macro fiber composite (MFC) piezoelectric actuator. For vibration control the use of a positive position feedback (PPF) controller is proposed. To include the PPF controller in the Abaqus software, a special subroutine is created. The developed control algorithm code makes it possible to solve an additional differential equation by the fourth order RungeKutta method. A numerical dynamic analysis is performed by the implicit procedure. The beam responses with and without controller activation are compared. The control subsystem model also includes the hysteresis phenomenon of the piezoelectric actuator. Numerical findings regarding the PPF controller’s effectiveness are verified experimentally.
Źródło:
Eksploatacja i Niezawodność; 2022, 24, 3; 468--477
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Use of an active element for dynamic control of a thin-walled laminated beam with kinematic excitation
Autorzy:
Gawryluk, Jarosław
Mitura, Andrzej
Teter, Andrzej
Powiązania:
https://bibliotekanauki.pl/articles/140174.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
proportional control
composite beam
MFC
dynamics
FEM
Opis:
The paper describes the dynamics of a composite cantilever beam with an active element. The vibrations of the kinematically excited beam are controlled with the use of a Macro Fiber Composite actuator. A proportional control algorithm is considered. During the analysis, actuator is powered by a time-varying voltage signal that is changed proportionally to the beam deflection. The MFC element control system with the implemented algorithm allowed for changing the stiffness of the tested structure. This is confirmed by the numerical and experimental results. Resonance curves for the beam with and without control are determined. The results show a very good agreement in qualitative terms.
Źródło:
Archive of Mechanical Engineering; 2019, LXVI, 3; 379-387
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-5 z 5

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies