Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "TDC determination" wg kryterium: Wszystkie pola


Wyświetlanie 1-8 z 8
Tytuł:
Analysis of application of chosen methods for tdc determination in marine diesel engines
Autorzy:
Łutowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/245396.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
transport
marine diesel engine
indication
TDC
Opis:
In the operating marine diesel engines the indication diagnostics tests are usually performed through a 0.5-1.0 me ter long indication channel which delays and disfigures the pressure signal being measured. the delay depends on the engine 's speed and load. the pressure sensor itself together with an amplifler is an additional source of delay and disfigurements, so the registered pressure curve is displaced even if theTDC piston's position hadbeen estimated with the highest accuracy. when the over exploited engine is being tested the angle of delay can achieve several degrees and differ for each cylinder. in that case cylinders' load is unequal and torsional vibrations occur in the engine operation. in case when some simplifying assumptions have been adopted the part of diagnostic information is lost what could lead to a false diagnosis. in the paper the attention is focused on the mistakes which could be made in the marine diesel engine diagnostics when different TDC assessment methods are used. TDC corrections with compression pressure analysis are possible only in case when crankshaft angle position is precise. in case of measurement with constant frequency such corrections are possible only when the engine is good balanced.
Źródło:
Journal of KONES; 2009, 16, 4; 301-306
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of top dead centre location based on the marine diesel engine indicator diagram analysis
Autorzy:
Varbanets, Roman
Zalozh, Vitalii
Shakhov, Anatoliy
Savelieva, Iryna
Piterska, Varvara
Powiązania:
https://bibliotekanauki.pl/articles/328708.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
diesel engine
top dead center
TDC pickup sensor
cylinder pressure monitoring
mean indicated pressure
indicated power
ship energy efficiency coefficient
silnik okrętowy
silnik spalinowy
czujnik ciśnienia
monitorowanie
średnie ciśnienie indykowane
moc indykowana
współczynnik efektywności energetycznej
Opis:
The article discusses methods for determining top dead center, based on the analysis of pressure diagrams of a marine engine. The advantages and disadvantages of different methods are shown. Diagnostics of marine engines during operation and the selection of optimal operating conditions is based on the analysis of gas pressure diagrams, as well as fuel supply and gas distribution diagrams. As a result of the analysis of the pressure diagrams, the indicator engine power is calculated, which is further used in the management of engine operation modes, in the calculation of specific indicators, as well as in the calculation of energy efficiency coefficients of marine vessels according to International Maritime Organization recommendations. The influence of the accuracy of determining the position of the top dead center on the calculation of the mean indicated pressure and indicator power is shown. The authors considered a method for determining top dead center, based on the solution of the equation P’= 0, which provides the required accuracy in calculating the mean indicated pressure and indicator power of the engine during operation. It is shown that the method can be applicable in marine engine working process monitoring systems as an alternative to hardware methods for determining the top dead center.
Źródło:
Diagnostyka; 2020, 21, 1; 51-60
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Increasing the accuracy of the mean indicated pressure determination by appointment of the TDC cylinder position
Autorzy:
Pawletko, R.
Powiązania:
https://bibliotekanauki.pl/articles/243489.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
Top Dead Centre determination
Mean Indicated Pressure accuracy
indicator diagram analysis
Opis:
The paper describes the problems of mean indicated pressure determination and the piston TDC (Top Dead Centre) position impact on this parameter in marine diesel engines. Mean indicated pressure Pi is one of the most important diagnostic parameters of marine engines. On the basis of its parameter, the assessment of the technical condition of each cylinder as well as the regulation of injection equipment can be made. Most of the available electronic indicators enable automatic calculation of mean indicated pressure on the basis of progress indicator diagram. As the research shows the greatest impact on the accuracy of the designation mean indicated pressure has errors of piston TDC position. These errors can be significant and therefore this may lead to engine misdiagnosis. The actual piston TDC correction methods were discussed, and they justified the need of their use in marine engines, despite the wide use of methods of determining the angular position of the crankshaft. The original method of TDC correction based on the model of curve of the compression with the exponent of a polynomial was introduced. The proposed method of TDC correction has been verified for a different types of marine engines.
Źródło:
Journal of KONES; 2014, 21, 2; 251-258
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Increasing the accuracy of the mean indicated pressure determination by appointment of the TDC cylinder position
Autorzy:
Pawletko, R.
Powiązania:
https://bibliotekanauki.pl/articles/245110.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
Top Dead Centre determination
Mean Indicated Pressure accuracy
indicator diagram analysis
Opis:
The paper describes the problems of mean indicated pressure determination and the piston TDC (Top Dead Centre) position impact on this parameter in marine diesel engines. Mean indicated pressure Pi is one of the most important diagnostic parameters of marine engines. On the basis of his parameter, the assessment of the technical condition of each cylinder as well as the regulation of injection equipment can be made. Most of the available electronic indicators enable automatic calculation of mean indicated pressure on the basis of progress indicator diagram. As the research shows the greatest impact on the accuracy of the designation mean indicated pressure has errors of piston TDC position. These errors can be significant and therefore this may lead to engine misdiagnosis. The actual TDC piston correction methods were discussed, and were justified the need of their use in marine engines, despite the wide use of methods of determining the angular position of the crankshaft. The original method of TDC correction based on the model of curve of the compression with the exponent of a polynomial was introduced. The proposed method of TDC correction has been verified for different types of marine engines.
Źródło:
Journal of KONES; 2014, 21, 4; 397-404
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of TDC determination methods on mean indicated pressure errors in marine diesel engines
Autorzy:
Pawletko, R.
Polanowski, S.
Powiązania:
https://bibliotekanauki.pl/articles/242218.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
TDC determination
coordinate of zero value of second derivative
TDC position influence on MIP errors
Opis:
The paper presents the results of comparative analysis of influence of different methods of TDC determination for the calculation errors of mean indicated pressure (MP). Lemag method based on zero point of first order derivative, used in PREMET pressure analyzers, was compared to the method based on a polynomial model of the compression process. Comparisons were made on the operating measurement data obtained on the low speed marine engine RTA96C which forms the main propulsion of the vessel and the medium speed engine MAN L28/32A. Measurements were made with onboard combustion PREMET analyzer. It was found that the method based on zero point of first order derivative can give the deviations of position of TDC in excess of 2°CA which is caused by disturbances associated with the measurement of pressure and interference associated with the generation of the angular axis. These errors are related to the accuracy of the methods of determining of the first derivative and the availability of a sufficient range of pure compression after TDC. The best results of determining the TDC position was obtained from the original method based on a polynomial model of the compression process. It should be emphasized that the proposed method enables individual adjustment of TDC for each cylinder and can be used even when the combustion begins before TDC. The conducted research proved the existence of significant influence of indicator graph TDC location on the mean indicated pressure calculation errors.
Źródło:
Journal of KONES; 2011, 18, 2; 355-363
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Marine diesel engine pistons instantaneous position experimental determination
Eksperymentalne wyznaczanie chwilowego położenia tłoka silnika okrętowego
Autorzy:
Kowalak, P.
Powiązania:
https://bibliotekanauki.pl/articles/258342.pdf
Data publikacji:
2007
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Technologii Eksploatacji - Państwowy Instytut Badawczy
Tematy:
okrętowy silnik spalinowy
szacowanie położenia
tłok TDC
marine diesel engine
diesel engines indication
piston TDC determination
Opis:
Przedstawiono eksperymentalne możliwości obserwacji ruchu tłoka poprzez skrzynię korbową silnika okrętowego. Wyznaczono charakterystyczne punkty położenia tłoka w czasie. opracowano metodę estymacji wystąpienia GMP tłoka na podstawie jego obserwowanych położeń. Zaproponowano model matematyczny umożliwiający szacowanie położenia dynamicznego GMP tłoka na podstawie obserwacji jego ruchu. Wykazano występowanie różnicy pomiędzy wystąpieniem GMP termodynamicznym, a GMP dynamicznym.
The experimental possibility of piston movement observation through the crankcase has been presented. The characteristic piston positioning points in the time domain have been determined. The piston TDC estimation methodology based on observed positioning points has been developed. A mathematic model for piston TDC estimation has been proposed. The difference between thermodynamic and dynamic TDC has been detected and presented.
Źródło:
Problemy Eksploatacji; 2007, 3; 113-120
1232-9312
Pojawia się w:
Problemy Eksploatacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research of the influence of marine diesel engine Sulzer AL 25/30 load on theTDC position on the indication graph
Autorzy:
Pawletko, R.
Polanowski, S.
Powiązania:
https://bibliotekanauki.pl/articles/247411.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
kinematic TDC determination
load influence on TDC position
Opis:
The article presents the research results of load influence on errors of the piston Top Dead Centre (TDC) position determined on indication graph with combustion. For TDC determination the method proposed by Polanowski is applied. This method is based on least-squares approximation with model of thermodynamic compression using apolynomial exponent. So, designated TDC are kinematics. This method make possible determination the TDC on the indicator diagram with combustion, as well as the total compression ratio and the dynamic error of pressure (offset). Research were done on the laboratory engine Sulzer 3AL25/30 for load range of 50-250 kW and rotational speed 750 rpm, which corresponds to 15-90% nominal load. Cylinder pressures were recorded with a resolution ofn O.5 OWK by means of multichannel recorder UNITEST 205. For pressure measurements were applied strain gauge pressure sensors Spais Company. For the analysis of indicator diagrams used its own specially developed algorithm and program for the automatic determination of TDC, based on the model of the compression process with the exponent of the polynomial. Simultaneously three parameters were determined: the position of TDC, the total compression ratio and offset the pressure. Additionally set the position of the zeros of the second order derivatives, which are sometimes considered as reference points to TDC of pistons. For smoothing of indicator diagrams their own algorithms and programs of moving approximation by polynomials of 3rd degree was used. The results of research have shown the essential load influence on the errors of TDC positions on indicator diagrams.
Źródło:
Journal of KONES; 2010, 17, 3; 361-368
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The dynamic TDC assigning on the marine four stroke engines indication diagram
Autorzy:
Kowalak, P.
Powiązania:
https://bibliotekanauki.pl/articles/243233.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
marine diesel engines
combustion processes
power estimation
determination of piston's TDC
Opis:
Determination of the internal combustion piston engine 's indicated power is a complex task. A number of difficulties lead to lots of solutions utilized to increase the accuracy of the result. This paper reports on the experiments concerned with a four stroke engine's piston dynamic position determination. Although the paper is mostly concerned with the piston's TDC definition, the experimental methodology can be utilized in the entire piston movement determination. A specially developed measuring assembly and its working principle utilized in the experiment have been presented too. It allows the acquiring of a set of time-position coordinates. Based on the coordinates, the mathematical algorithm for dynamic piston positioning can be developed. As the piston movement was being observed from the crankcase side, the methodology proved to be relatively cheap and easier for installation, compared to proximity sensors installed in the cylinder head. The advantage of optical sensors and light pipes being used was reduction of the explosion risk in oil mist environment inside the crank case.
Źródło:
Journal of KONES; 2007, 14, 2; 259-266
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-8 z 8

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies