Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Muneer, M." wg kryterium: Wszystkie pola


Wyświetlanie 1-2 z 2
Tytuł:
Degradation and detoxifi cation of 2-chlorophenol aqueous solutions using ionizing gamma radiation
Autorzy:
Basfar, A. A.
Muneer, M.
Alsager, O. A.
Powiązania:
https://bibliotekanauki.pl/articles/148378.pdf
Data publikacji:
2017
Wydawca:
Instytut Chemii i Techniki Jądrowej
Tematy:
2-chlorophenol
degradation
detoxification
gamma irradiation
aqueous solution
Opis:
Chlorophenols are compounds with high toxicity, poor biodegradability, and carcinogenic and recalcitrant properties. This work studies, for the first time, the destruction and detoxification of 2-chlorophenol (2-CP) in water using 60Co gamma radiation under different conditions including varied radiation doses, addition of hydrogen peroxide (H2O2), and varied pH values. High-performance liquid chromatography (HPLC) and ion chromatography (IC) confirmed a successful degradation of 2-CP to primarily yield phenol molecules and chloride anions. A radiation dose as low as 25 kGy achieved approximately 90% removal of 50–150 ppm of 2-CP in neutral water. However, the addition of a strong oxidizer such as H2O2 to 2-CP solutions reduced the required dose to achieve 90% removal to at least 1.3-fold. The reduction in radiation doses was also observed in acidic and alkaline media, reducing the required doses of 90% removal to at least 0.4-fold. It was imperative to study the toxicity levels of the oxidation by-products to provide directions for the potential applicability of this technology in water treatment. Toxicology Microtox® bioassay indicated a significant reduction in the toxicity of the degradation by-products and the detoxification was further enhanced by the addition of H2O2 and changing the pH to more acidic or alkaline conditions. These findings will contribute to the knowledge of the removal and detoxification of such challenging environmental contaminant and could be potentially applied to other biologically resistant compounds.
Źródło:
Nukleonika; 2017, 62, 1; 61-68
0029-5922
1508-5791
Pojawia się w:
Nukleonika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of changing injection temperature on some mechanical and morphological properties for polypropylene material (PP)
Autorzy:
Al-Zubiedy, Ali
Muneer, Ruaa M.
Powiązania:
https://bibliotekanauki.pl/articles/111895.pdf
Data publikacji:
2019
Wydawca:
Stowarzyszenie Menedżerów Jakości i Produkcji
Tematy:
polypropylene PP
injection molding
mechanical properties of polymers
polipropylen PP
formowanie wtryskowe
właściwości mechaniczne
Opis:
This is a study of a medical injection factory-Babylon carried out in order to achieve proper mechanical and morphological properties, PP has been injection molded by using cold runner injection molding machine with temperature variation (198, 200, 203……2200C) for ten samples. The physical and mechanical properties of PP product were examined. It has been found that the Shore hardness decreases linearly with injection molding temperature increasing. The tensile strength has a similar behavior to the hardness. However, it has been found that the MIF (Melt Index Flow) rates increases with the increase of injection molding temperature. The density of PP has been found for both virgin PP and the samples, it has been found that the density decreases with increasing operation temperature. FTIR (Fourier Transmission Infrared) spectra were taken for both samples with high and low operation temperature. Besides the SEM (Scanning Electronic Microscopy) test shows the difference in the morphology of the product surface and the PP product at high and low operation temperature. Moreover, for all these properties, the PP product exhibits good mechanical properties (hardness, tensile strength, density) for the samples produced at temperature lower than 2070C. While the physical properties such as MIF improved with injection temperature increasing, additionally, the SEM images show that the sample produced in low temperature have surface damage.
Źródło:
Production Engineering Archives; 2019, 24; 20-24
2353-5156
2353-7779
Pojawia się w:
Production Engineering Archives
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies