Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "dynamometer" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
Investigation of the integrated powertrain on the dynamometer stand
Autorzy:
Karczewski, M.
Szczęch, L.
Walentynowicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/243951.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
dynamometer stand
integrated powertrain
Opis:
Description of the test stand for investigation of the integrated powertrain (powerpack) for armoured modular vehicle (AMV), disassembled from vehicle, is presented in this paper. The powerpack unit consist of a diesel engine, a gearbox and a cooling unit with a hydraulic fan drive. The stand is equipped with measuring devices for torque measure, fuel consumption, exhaust smoke and exhaust gas components emission analysers. The powerpack has been loaded by a hydraulic dynamometer of power range up to 1250 kW. It is dynabar water dynamometer with high dynamics of load changes. For control the motor and drive, system the original control panels from the vehicle was used. The original start-up unit, mid fuel tank and air filters were used too. Research on the powerpack unit was made in the steady state versus the engine load and speed. The parameters of the engine and exhaust components were measured and compared with the catalogue values. Two modes of engine work were compared – economic and dynamic modes. Those differences between two modes are result of maximum fuel consumption decreasing. The parameters of engine work were comparable in middle and low range of engine load. On the stand investigation in transient states during free engine acceleration were made. It was found that additional load of engine is too high and this problem should be clarified.
Źródło:
Journal of KONES; 2013, 20, 4; 147-153
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation of the vapour cooling system on the dynamometer stand
Badania wyparkowego układu chłodzenia na stanowisku dynamometrycznym
Autorzy:
Walentynowicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/950143.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
spalinowe silniki tłokowe
układy chłodzenia
wyparkowy układ chłodzenia
stanowisko dynamometryczne
badania eksperymentalne
combustion engines
cooling systems
vapour cooling system
dynamometer test stand
experimental investigations
Opis:
Possibility of improvement of work parameters of the turbocharged diesel engine through increasing of the liquid cooling temperature was the aim of presented investigations. Diesel engine was equipped in the closed vapour cooling system with metal separator made by using tubes and copper pipe fitting. The water was used as a cooing liquid. Investigations were realised at pressure in cooling system less then 0,1 mpa what limited the range of torque and the engine speed considerably. It was got increasing the temperature of cooling liquid flown out from the engine to approx. 110 centigrade. The growth of the liquid temperature caused decreasing of the carbon oxide parts (to 50%) and hydrocarbons (to 50%) in the range of the low engine torque. However the parts of the oxides of nitrogen grew up near this (approx. 50ppm) and the temperature of exhaust gas was higher also (about 50 centigrade). The temperature of lubrication oil was higher 40...60°C also. The fuel consumption of the engine was comparable. Increasing of the flow intensity of the cooling liquid through additional cooling of the compensation tank and the using the bigger water pump is purposeful during future investigations. It is necessary to use control system for regulation of cooling intensity.
Celem prezentowanych badań było sprawdzenie możliwości poprawienia parametrów pracy turbodoładowanego silnika o zapłonie samoczynnym poprzez zwiększenie temperatury cieczy chłodzącej. Silnik ten wyposażono w zamknięty układ chłodzenia z metalowym separatorem wykonanym z rurek i kształtek miedzianych. Cieczą chłodzącą była woda. Badania przeprowadzono przy nadciśnieniu nieprzekraczającym 0,lmpa, co znacznie ograniczyło zakres obciążenia i prędkości obrotowej silnika. Uzyskano zwiększenie temperatury cieczy chłodzącej na wypłynie z silnika do ok. 110oc. Wzrost temperatury cieczy chłodzącej spowodował zmniejszenie udziałów tlenku węgla (do 50%) i węglowodorów (do 50%) w zakresie małego obciążenia silnika, jednak wzrosły przy tym udziały tlenków azotu (ok. 50ppm) oraz wyższa była temperatura spalin (ok.50 stopni Celsjusza). Wyższa była także temperatura oleju smarującego silnik o około 40...60 stopni Celsjusza. Ekonomiczność pracy silnika była porównywalna. Podczas dalszych badań celowe jest zwiększenie intensywności przepływu cieczy chłodzącej poprzez dodatkowe chłodzenie zbiornika wyrównawczego i zastosowanie większej pompy wodnej. Celowe jest zastosowanie systemu automatycznego sterowania intensywnością chłodzenia.
Źródło:
Journal of KONES; 2007, 14, 3; 597-602
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Diagnozowanie zintegrowanego zespołu napędowego KTO Rosomak
Diagnosing power pack of AMV Rosomak
Autorzy:
Karczewski, M.
Szczęch, L.
Walentynowicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/347078.pdf
Data publikacji:
2013
Wydawca:
Akademia Wojsk Lądowych imienia generała Tadeusza Kościuszki
Tematy:
silnik spalinowy
zintegrowany zespół napędowy
KTO Rosomak (wóz bojowy)
diagnostyka techniczna
stanowisko dynamometryczne
combustion engine
integrated propulsion system
AMV Rosomak (combat vehicle)
technical diagnostics
dynamometer test stand
Opis:
W referacie przedstawiono stanowisko dynamometryczne do badania zintegrowanego zespołu napędowego KTO Rosomak. Stanowisko to umożliwia badanie parametrów pracy układu napędowego oraz prowadzenie szerokiej diagnostyki w przypadku wystąpienia awarii. Wyniki pomiarów prowadzonych na silniku remontowanym po wybuchu miny pod pojazdem są przedstawione w końcowej części referatu.
The dynamometer test stand for investigating the AMV Rosomak integrated propulsion system is discussed in the paper. The stand enables the measurement of propulsion system parameters and extended diagnostics in case of damage. The investigation results of an engine overhaul after an IED explosion are shown at the end of the paper.
Źródło:
Zeszyty Naukowe / Wyższa Szkoła Oficerska Wojsk Lądowych im. gen. T. Kościuszki; 2013, 2; 94-108
1731-8157
Pojawia się w:
Zeszyty Naukowe / Wyższa Szkoła Oficerska Wojsk Lądowych im. gen. T. Kościuszki
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies