Temat: engine chamber - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: The effect of location on the combustion chamber for the toxicity exhaust in self-ignition engine Ursus 4390
Autorzy:: Kalina, P.
Powiązania:: https://bibliotekanauki.pl/articles/247388.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: piston engine
diesel
combustion chamber
Opis:: As a part of the research work done on the engine URSUS 4390 which aimed at increasing power while reducing exhaust gas emissions, intake channels in the head, shape of the combustion chamber and compression ratio were modified. Proper injection equipment was selected and atomizer nozzles were constructed. In the first phase of the research, toroidal combustion chamber was located in factory design location. In the article there are presented results of exhaust gas emissions in selected operating points of engine URSUS 4390 for various positions of experimental combustion chamber. An innovative method of changing the position of the combustion chamber related to the piston axis was developed. A rotating insert with eccentrically extruded combustion chamber was mounted in piston axis. Rotation of the insert by a given angle resulted in displacement of combustion chamber around the axis of rotation. For each particular position of combustion chamber, concentration of toxic flue gas components and smoke index was measured at full load with rotational speed of 1400 and 2000 rpm. Proposed piston construction with rotating insert allowed to significantly decreasing duration of the research, which aimed at verification of combustion chamber relative location to injector and inlet nozzle. This way the necessity of construction of new sets of pistons and lapping them each time was avoided. As a result of the work, 11 locations of combustion chamber were tested. The study allowed picking the position of combustion chamber, which guarantees lowest emissions of toxic flue gas components.
Źródło:: Journal of KONES; 2015, 22, 2; 97-102
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Internal combustion micro-chambers and micro-engines
Autorzy:: Kraszewska, H.
Rusin, M.
Powiązania:: https://bibliotekanauki.pl/articles/244746.pdf
Data publikacji:: 2008
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engine
microengine
shaft less engine
combustion chamber
Opis:: Technological progress caused miniaturization of internal-combustion engines. They found application in many areas. The acquaintance of the ignition and combustion processes in the small volumes, the solution of the problem of piston movement under the influence of a pulse combustion in chambers, the choice of materials and problems related with the mixtures and exhaust creation, all these issues require a exact acquaintance for the purpose of optimization of the micro engine performance. In the paper, some issues are talked over on the base of investigations performed on the small volume chambers in single compression machines and in the shaftless two-cycle engine. Researched was the influence of the micro chamber size and of the area/volume ratio value on the processes of combustion occurring in the very small volumes and with the large values of area/volume ratio. Together with raise of the area/volume ratio, the value of the combustion pressure impulse becomes lower. The influence of the chamber material type on the combustion processes was defined, both in the single compression machine as in the micro engine. The existence of micro chamber size influence on the combustion limits of the fuel/air mixtures was designated. It has been determined that the range of the combustion limit is decreased with diminishing of the combustion chamber diameter, at the same time these changes are not the function of the area/volume ratio value changes. The maximum values of the combustion pressure appeared when chamber was supplied with stoichiometric mixture, irrespective of the chamber dimensions.
Źródło:: Journal of KONES; 2008, 15, 4; 283-288
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: The influence of the shape of the combustion chamber on exhaust gases toxicity in T370 engine
Autorzy:: Kalina, P.
Kawalec, M.
Powiązania:: https://bibliotekanauki.pl/articles/243782.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: diesel engine
combustion chamber
geometry
toxicity
Opis:: An important issue in construction of combustion chamber in compression-ignition engines is proper selection of its shape and size. Both features are dependent on several factors such as fuel injector location and angle, spray atomizer selection (amount of holes, their diameter and angular position), location of inlet valve and air turbulence. By doing research on prototype engine T370, an analysis of influence of combustion chamber size and its modifications going towards lip construction on flue gas toxicity was done. The diameter and depth of combustion chamber was being changed while maintaining the same compression ratio. After that, a modification of tested combustion chambers was made by creating so called “lip”, which aim was to create a swirl of injected fuel in the vertical plane. To visualize the changes in swirl, a numerical analysis of fuel injection into combustion chamber was made. In discussed study, emission tests were performed according to ECE-R49. During the research six combustion chambers with diameters 60, 63 and 66 mm (and their modification) were investigated. Tests were performed for several types of injectors and different injection timing. However, for analysis of combustion chamber size the results are presented for the same injectors but with optimized injection timing.
Źródło:: Journal of KONES; 2015, 22, 2; 104-108
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: The rig stand for testing integrated rocket ramjet engine
Autorzy:: Rowiński, A.
Powiązania:: https://bibliotekanauki.pl/articles/246853.pdf
Data publikacji:: 2016
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turbine engine
combustion chamber
detonation combustion
rotating detonation engine
RDE
Opis:: Integrated rocket ramjet engine is adapted to aircraft propulsion and supersonic missiles moving at the speed of 8 Ma. The engine’s construction enables flexibly benefit from both types of drive depending on the conditions of the flight. The ejector mode of operation applicable to Mach numbers smaller than 2 cooperate with the rocket engine positioned in flow channel. Secondary air stream enters the engine through the convergent divergent nozzle and supplies the air to the ejector and booster. Rocket engine using the ejector effect would be used only in the phase of accelerating an object to the supersonic speed and then the drive would gradually shift to ramjet. The range of speed for the ramjet mode is 2-6 Mach. The prototype of the rocket ramjet engine of over 1300 N is equipped with annular combustion chamber in which phenomena of rotating detonation as well as the aero spike nozzle were used. Both the test stand as well as the engine is adapted to trials suitable to the conditions of a flight at the speed of 1.4 Ma. The test stand is powered by compress air coming from the instalment set up in the earth test bed and by oxygen and methane at a pressure of 10 bar. The rig is designed for functional tests of prototype, areas of the creation of mixture of firearms used to measuring and the range of stable functioning of the engine in the ramjet mode. Moreover, the measured parameters in gas supply installations as well as the temperature and pressure in the combustion chamber and thrust created by integrated rocket ramjet engine are measured.
Źródło:: Journal of KONES; 2016, 23, 4; 421-428
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Study on kerosene atomization process under a high speed air stream
Autorzy:: Perkowski, W.
Irzycki, A.
Snopkiewicz, K.
Grudzień, Ł.
Kawalec, M.
Powiązania:: https://bibliotekanauki.pl/articles/247137.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: transport
aircraft engine
combustion chamber
fuel atomization
Opis:: For the needs of fuel-injection system development for the experimental detonation combustion chamber with a rotating detonation (PoiG - Project: "Turbine engine with detonation combustion chamber") a series of experiments with injection of kerosene under a high speed air stream was performed at the Institute of Aviation. The proper preparation of combustible mixture is very important for the initiation and sustenance of a rotating detonation. The task in case of kerosene-air mixture is far more difficult than for mixtures of hydrogen-air or kerosene-oxygen. A simple stream injector has been tested as a base system, and the kerosene was injected perpendicular to the air stream vector directly from the plane wall of the constant cross-section channel. The process of injection and atomization of kerosene was observed in the special transparent visualization chamber, enabling the spray observation of two mutually perpendicular directions. In subsequent experiments air pressure, air temperature and air flow velocity as well as and injection pressure of kerosene were varied. The tested process was photographed and, in case of chosen experiments, filmed using a high-speed digital camera. The surveys were aimed at identifying and assessing of following parameters of fuel atomization process: the range of the fuel stream and filling grade of research channel with aerosol, aerosol homogeneity and the size of forming it droplets, the possible presence of fuel streams flowing down the walls of channel. The resulting photos allowed for more comprehensive, but only a qualitative assess of the spraying process, while the filmed small regions of visualization chamber allowed the counting down and dimensioning of droplets. This paper presents a test facility and measuring techniques applied during the research activity and selected results of carried out tests.
Źródło:: Journal of KONES; 2011, 18, 4; 341-347
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: Start-up and acceleration control of the turbine engine with the detonation combustion chamber
Autorzy:: Balicki, W.
Powiązania:: https://bibliotekanauki.pl/articles/247622.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: turbine engine
combustion chamber
rotating detonation engine (RDE)
start-up control
Opis:: This article presents the results of tests of helicopter turbine engine, where the classic combustion chamber was replaced with an innovative solution. In this chamber instead of the classic combustion deflagration, was generated a rotating detonation. Theoretical considerations expected to get a higher engine efficiency, because as the thermodynamic Fickett-Jacobs cycle, which can describe the working principle turbine engine detonation chamber, has a higher efficiency than a Brayton cycle, according to which the engines of conventional chamber are working. The appearance of detonation combustion was diagnosed basing on observation of the gas pressure flue in the chamber, using piezoelectric sensors. Before the detonation chamber was used in turbine engine, a series of problems on the various methods of initiation of detonation process and the procedures for controlling the flow rate into the chamber of air and fuel were solved. There was a test stand constructed, which used a helicopter turbine engine GTD-350, wherein the jugs combustion chamber was replaced with detonation chamber. A control system for the flow of fuel in the combustion chamber was developed: aviation kerosene Jet-A1 with addition of hydrogen. With its use obtained unfailing starts of chamber, also the engine running on the idle and on the flight range and accelerations at idle range to flight range. The possibility of the detonation combustion for a long time, especially in transient states - practically limited only by the capacity of fuel tanks – is the achievement of the research team.
Źródło:: Journal of KONES; 2015, 22, 4; 21-27
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: Study of combustion chamber with a rotating detonation
Autorzy:: Łukasik, B.
Rowiński, A.
Irzycki, A.
Snopkiewicz, K.
Powiązania:: https://bibliotekanauki.pl/articles/246882.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engine
turbine engines
combustion chamber
rotating detonation
Opis:: Institute of Aviation in Warsaw realizes the project concerning the application of the phenomenon of combustion with rotating detonation to the combustion chamber designed and destined for turbine engines. The test chamber is adapted for supplying both with liquid (aviation kerosene) and gaseous fuels in the form of mixture with compressed air. It is equipped with a probe for pressure and temperature measurements inside the flame tube as well as at its inlet and outlet sections. The measuring system allows measurement of physical phenomenon at low (1 kHz) and high (1 MHz) frequencies. Electric signals representing temperature and pressure sensor's measuring quantities, fuel and compressed air supply systems parameters and ignition-triggering values are collected using data acquisition system controlled by a computer. The prototype of the combustion chamber was examined at the especially designed test facility to determine at quasi-static operating conditions its following characteristics: speed of inside shock wave, exhaust gas thermodynamic parameters and ignition and going-out limits of gaseous fuel. In this article construction of test bench, schematic diagrams of measurement and power supply systems as well as the research process, the way of measurement data analysis recorded during the carried-out experiments and data validation manner are detailed described. The method of measurement data processing, the resulting graphs, and the conclusions of the study are presented as well.
Źródło:: Journal of KONES; 2012, 19, 2; 313-320
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Testing of initiation of rotating detonation process in hydrogen - air mixtures
Autorzy:: Balicki, W.
Irzycki, A.
Łukasik, B.
Snopkiewicz, K.
Powiązania:: https://bibliotekanauki.pl/articles/247318.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: internal combustion engine
turbine engines
combustion chamber
rotating detonation
Opis:: The paper presents results of some research work done in the project, which aims to apply of an innovative combustion chamber to the turbine engine. Expected benefits of using of a new chamber in which classical deflagration type combustion process would be replaced with a detonation combustion type, arise from greater efficiency of FickettJacobs cycle, which corresponds to rotating detonation combustion, in comparison to "classical" Brayton cycle, characteristic of deflagration combustion. The presented task concerned fundamental research carried out on test bench designed and built at the Institute of Aviation in Warsaw. To initiate the detonation combustion in the fuel-air mixtures the ignition device of appropriately high energy is necessary. The released energy should be directed to the area where the mixture has proper constitution - preferably close to stoichiometric one. Four different ignition manners were examined in the course of research: electrical ignition system adapted from turbine engine (semiconductor spark plug), powder charge ignition (handgun cartridges), detonation primer ignition using pentryt, and high voltage discharge (plasma jet). The appearance of detonation type combustion was identified on the basis of combustion gas pressure run, measured using piezoelectric sensors at a frequency of 1 MHz.
Źródło:: Journal of KONES; 2012, 19, 2; 25-34
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: Investigations of the working process in a dual-fuel low-emission combustion chamber for an FPSO gas turbine engine
Autorzy:: Serbin, Serhiy
Diasamidze, Badri
Dzida, Marek
Powiązania:: https://bibliotekanauki.pl/articles/1585065.pdf
Data publikacji:: 2020
Wydawca:: Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:: gas turbine engine
dual-fuel combustion
combustion chamber
liquid fuel
Opis:: This investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dualflow low-emission gas turbine combustion chamber, a generalized method is used, based on the numerical solution of the system of conservation and transport equations for a multi-component chemically reactive turbulent system, taking into consideration nitrogen oxides formation. The Eddy-Dissipation-Concept model, which incorporates Arrhenius chemical kinetics in a turbulent flame, and the Discrete Phase Model describing the interfacial interaction are used in the investigation. The obtained results confirmed the possibility of organizing efficient combustion of distillate liquid fuel in a low-emission gas turbine combustion chamber operating on the principle of partial preliminary formation of a fuel-air mixture. Comparison of four methods of liquid fuel supply to the channels of radial-axial swirlers (centrifugal, axial, combined, and radial) revealed the advantages of the radial supply method, which are manifested in a decrease in the overall temperature field non-uniformity at the outlet and a decrease in nitrogen oxides emissions. The calculated concentrations of nitrogen oxides and carbon monoxide at the flame tube outlet for the radial method of fuel supply are 32 and 9.1 ppm, respectively. The results can be useful for further modification and improvement of the characteristics of dual-fuel gas turbine combustion chambers operating with both gaseous and liquid fuels.
Źródło:: Polish Maritime Research; 2020, 3; 89-99
1233-2585
Pojawia się w:: Polish Maritime Research
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 10.

Tytuł:: Snizhenie intensivnosti pul'sacionnogo gorenija v kamere sgoranija GTD ispol'zovanijem plazmennykh stabilizatorov
Reduction in the intensity of the pulsation burning in gas turbine combustion chamber using plasma stabilizers
Autorzy:: Serbin, S.
Mostipanenko, A.
Kozlovskiy, A.
Powiązania:: https://bibliotekanauki.pl/articles/76712.pdf
Data publikacji:: 2015
Wydawca:: Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:: reduction
gas turbine engine
combustion chamber
pulsating combustion
mathematical modelling
Źródło:: Motrol. Motoryzacja i Energetyka Rolnictwa; 2015, 17, 2
1730-8658
Pojawia się w:: Motrol. Motoryzacja i Energetyka Rolnictwa
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 11.

Tytuł:: Analiza wybranych wskaźników pracy silnika dwuprzepływowego z dwiema komorami spalania
Analysis of chosen work parameters of two-comustor turbofan engine
Autorzy:: Jakubowski, R.
Kuźniar, M.
Powiązania:: https://bibliotekanauki.pl/articles/254334.pdf
Data publikacji:: 2016
Wydawca:: Instytut Naukowo-Wydawniczy TTS
Tematy:: silnik dwuprzepływowy
spalanie
komora spalania
turbofan engine
combustion
combustion chamber
Opis:: W artykule przedstawiono wyniki badań numerycznych porównujących efektywność pracy klasycznego silnika dwuprzepływowego oraz silnika dwuprzepływowego z dwiema komorami spalania. Na wstępie podano istotne informacje dotyczące konstrukcji silnika dwuprzepływowego z dodatkową komorą spalania usytuowaną pomiędzy turbiną wysokiego i niskiego ciśnienia i wynikające stąd korzyści eksploatacyjne silnika. Przedstawiono zasadnicze różnice w modelu silnika z dwiema komorami spalania oraz przeanalizowano ich wpływ na osiągi silnika. Wykonano symulacje komputerowe pracy silnika z dwiema komorami spalania i porównano je z wynikami dla klasycznego silnika dwuprzepływowego. Wskazano na istotne cech silnika dwukomorowego, które są związane z doborem parametrów obiegu silnika. Wykazano, że w odróżnieniu od klasycznego silnika dwuprzepływowego można wyznaczyć spręż całkowity silnika, dla którego spełnione będzie jednocześnie kryterium osiągnięcia minimum jednostkowego zużycia paliwa i maksimum ciągu jednostkowego. W wyniku obliczeń parametrów eksploatacyjnych wyznaczono przebiegi podstawowych parametrów pracy silnika dla różnych warunków lotu i wskazano występowanie zakresów konstrukcyjnych i eksploatacyjnych, w których silnik z dwiema komorami spalania będzie rozwiązaniem korzystniejszym niż klasyczny silnik dwuprzepływowy. Na podstawie wykonanych analiz sformułowano wnioski dotyczące porównania cech eksploatacyjnych obydwu typów silników.
The results of numerical investigation of perfor-mance of the classical turbofan engine and a two-combustor turbofan are presented in the paper. The basic information of the two-combustor turbofan are presented in the beginning. The differences in the model of two-combustor turbofan engine vs. classical turbofan were presented and their influence on engine performance was discussed. The numerical simulation of compared engine performance was done. By this way it was presented that it was possible to establish two-combustor engine parameters that specific thrust is maximum and specific fuel consumption is minimum. This is impossible to fulfillment for classical turbofan engine. The simulation of engine performance vs. altitude and flight velocity was done. By this way it was demonstrated that two-combustor turbofan engine performance are close to performance of classical turbofan and that there are some flight condition, for with two-combustor engine could be better than classical turbo-fan.
Źródło:: TTS Technika Transportu Szynowego; 2016, 12; 100-105
1232-3829
2543-5728
Pojawia się w:: TTS Technika Transportu Szynowego
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 12.

Tytuł:: Wpływ frakcji węglowodorowych benzyn silnikowych na czystość komory spalania silnika
Influence of petrol hydrocarbon fractions on engine combustion chamber purity
Autorzy:: Jakóbiec, J.
Wysopal, G.
Powiązania:: https://bibliotekanauki.pl/articles/314254.pdf
Data publikacji:: 2011
Wydawca:: Instytut Naukowo-Wydawniczy "SPATIUM"
Tematy:: silnik spalinowy
benzyna silnikowa
komora spalania
engine
motor spirits
combustion chamber
Opis:: W artykule zamieszczono informacje dotyczące osadów w samym paliwie i na elementach roboczych silnika powstałych w procesie spalania benzyn silnikowych. Podkreślono, że skłonność benzyn silnikowych do wytwarzania osadów w komorze spalania silnika jest ściśle związana z ich budową chemiczną, konstrukcją silnika i jego warunkami pracy. Postęp w dziedzinie pakietu dodatków uszlachetniających i poziom dozowania pozwala stopniowo rozwiązywać wiele problemów dotyczących tworzenia się osadów w silniku.
In this paper information about sediments in fuel and made during combustion process of petrol on working elements are presented. It is emphasized petrol tendency to produce sediments in combustion chamber, which is result of their chemical structure, engine construction and working conditions. Development in domain of refined additives and dosage level allow gradually solve many problems related with form of sediments in engine.
Źródło:: Autobusy : technika, eksploatacja, systemy transportowe; 2011, 12, 5; 167-174
1509-5878
2450-7725
Pojawia się w:: Autobusy : technika, eksploatacja, systemy transportowe
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 13.

Tytuł:: Wpływ warunków obciążenia silnika na temperaturę ścian komory spalania
An influence of load on temperature of combustion chamber walls in SI engine
Autorzy:: Kubica, G.
Powiązania:: https://bibliotekanauki.pl/articles/196839.pdf
Data publikacji:: 2010
Wydawca:: Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:: silnik spalinowy
silnik o zapłonie iskrowym
komora spalania
pomiar temperatury
engine
SI engine
combustion chamber
temperature measurement
Opis:: Celem prowadzonych badań było wyznaczenie temperatury ścian komory spalania, w zależności od warunków obciążenia silnika. Do realizacji tego celu zastosowano nową metodę, polegającą na określaniu rzeczywistej temperatury elementu komory spalania w czasie pracy silnika, na podstawie zarejestrowanej krzywej stygnięcia, po wyłączeniu silnika. Prezentowana metoda bazuje na standardowym systemie pomiaru i akwizycji danych bez konieczności wykonywania prac adaptacyjnych silnika. Wstępne pomiary wskazują na dużą uniwersalność jej zastosowania, co jest znaczącym atutem tego rozwiązania, ponieważ bezpośredni pomiar temperatury wewnątrz komory spalania, w czasie pracy silnika jest możliwy jedynie na przystosowanych silnikach badawczych, wyposażonych w zaawansowane, bezprzewodowe układy pomiarowe.
The determine of combustion chamber walls in depend of engine load was the main aim of the research leaded. To achieve that goal were used the new method of determining of real wall temperature during engine run, upon registered colling down curve after engine stop. The presented method is based on standard temperature measurement with thermocouple & DAQ. The engine adaptation is unnecessary. The preliminary measurements showing the application very universal. It is significent advantage, because the current control of combustion chamber walls temperature is possible only in examination engine well equipped with advanced wireless measurement systems.
Źródło:: Zeszyty Naukowe. Transport / Politechnika Śląska; 2010, 66; 57-64
0209-3324
2450-1549
Pojawia się w:: Zeszyty Naukowe. Transport / Politechnika Śląska
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 14.

Tytuł:: Investigations of the emission characteristics of a dual-fuel gas turbine combustion chamber operating simultaneously on liquid and gaseous fuels
Autorzy:: Serbin, Serhiy
Diasamidze, Badri
Gorbov, Viktor
Kowalski, Jerzy
Powiązania:: https://bibliotekanauki.pl/articles/1573591.pdf
Data publikacji:: 2021
Wydawca:: Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:: gas turbine engine
dual-fuel combustion
combustion chamber
liquid and gaseous fuels
Opis:: This study is dedicated to investigations of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. As the object of the research, a low-emission gas turbine combustion chamber with partial premixing of fuel and air inside the outer and inner radial-axial swirls was chosen. The method of the research is based on the numerical solution of the system of differential equations which represent the physical process of mass and energy conservation and transformations and species transport for a multi-component chemically reactive turbulent system, considering nitrogen oxides formation and a discrete ordinates model of radiation. The chemistry kinetics is presented by the 6-step mechanism of combustion. Seven fuel supply operating modes, varying from 100% gaseous fuel to 100% liquid fuel, have been analysed. This analysis has revealed the possibility of the application of computational fluid dynamics for problems of dual-fuel combustion chambers for the design of a floating vessel’s gas turbine. Moreover, the study has shown the possibility of working in different transitional gaseous and liquid fuel supply modes, as they satisfy modern ecological requirements. The dependencies of the averaged temperature, NO, and CO concentrations along the length of the low-emission gas turbine combustion chamber for different cases of fuel supply are presented. Depending on the different operating modes, the calculated emission of nitrogen oxides NO and carbon monoxide CO at the outlet cross-section of a flame tube are different, but, they lie in the ranges of 31‒50 and 23‒24 mg/nm3 on the peak of 100% liquid fuel supply mode. At operating modes where a gaseous fuel supply prevails, nitrogen oxide NO and carbon monoxide CO emissions lie in the ranges of 1.2‒4.0 and 0.04‒18 mg/nm3 respectively.
Źródło:: Polish Maritime Research; 2021, 2; 85-95
1233-2585
Pojawia się w:: Polish Maritime Research
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 15.

Tytuł:: The impact of intake canal geometry on kinematics of load in combustion chamber
Wplyw geometrii kanalu dolotowego na kinematyke ruchu ladunku w przestrzeni roboczej silnika tlokowego
Autorzy:: Piatkowski, P.
Powiązania:: https://bibliotekanauki.pl/articles/792662.pdf
Data publikacji:: 2012
Wydawca:: Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:: supply system
engine
piston engine
combustion chamber
filling
kinetic property
intake canal geometry
flow resistance
fuel consumption
turbulence
Źródło:: Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2012, 12, 1
1641-7739
Pojawia się w:: Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "engine chamber" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język