Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "x-ray" wg kryterium: Temat


Wyświetlanie 1-13 z 13
Tytuł:
Mechanically Stimulated Changes in Surface Electrical Conductivity of X-Irradiated Silicon Crystals
Autorzy:
Lys, Roman
Żyłka, Marta
Shykorjak, Josyp
Slobodzyan, Dmytro
Żyłka, Wojciech
Pavlyk, Bohdan
Powiązania:
https://bibliotekanauki.pl/articles/2201919.pdf
Data publikacji:
2023
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
X-ray irradiation
silicon
uniaxial deformation
dislocation
Opis:
Changes in the resistance of single crystals of p-type conductivity silicon under the action of mechanical loading were investigated in this research. Also, non-irradiated and pre-irradiated X-rays experimental samples were studied. It was found that at small deformation values when they are at the initial stage of the action of elastic deformation, a section forms and increases, on which the resistance practically does not depend on the applied mechanical load. In irradiated crystals, at small deformation values, electron generation processes dominate, which then recombine with the main carriers – holes. The consequence of such processes is the appearance of a maximum increase in electrical resistance at the initial stage of elastic deformation of experimental samples irradiated with X-rays. Charge carrier generation processes begin to dominate with further deformation. Such processes occur as a result of the release of acceptor centers from other complex defects, which are destroyed during the deformation of the Si crystal and captured by mobile dislocations. Thus, the processes of generation of charge carriers prevail over the processes of gettering and, accordingly, a mechano-stimulated decrease in the electrical resistance of p-Si samples occurs.
Źródło:
Advances in Science and Technology. Research Journal; 2023, 17, 2; 226--231
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Industrial X-ray testing without intermediate data carriers of information
Przemysłowe badanie rentgenowskie bez pośrednich nośników informacji
Autorzy:
Troitskiy, V.
Powiązania:
https://bibliotekanauki.pl/articles/107722.pdf
Data publikacji:
2018
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
film radiography
flash-radiography
digital image
scintillator
solid-state transducer
X-ray mini technology
radiografia błonowa
radiografia błyskowa
obraz cyfrowy
scyntylator
przetwornik półprzewodnikowy
technologia przenośnych urządzeń X-ray
Opis:
The new direction of radiography is Flash-radiography (FR ) which doesn’t have intermediate data carriers (films and storage plates). FR produces a quick image. It provides low testing cost, and capability of multi-angle real time internal defects monitoring of the objects. In film radiography, if relative photometric density is more than 4, then the snapshots become virtually unreadable and they can be difficult to be digitized. Current film-free technologies do not have this disadvantage and, besides, give results in a digital form without special digitizing systems. Digital data contain radiation images of internal defects, expand the flawdetection possibilities and reduce testing cost. Flash-radiography is based on portable X-ray television, which allows the observation of X-ray testing results on a monitor screen. The internal defects examination from different angles may be carried out. Flash-radiography with digital solid-state transducers is the most perspective one with sensitivity up to 0.1% of examined metal’s thickness at resolution exceeding 10 pairs of lines per mm. Application of small-size movable solid-state transducers opens new technological capabilities. They can be located and moved in the zones where positioning of film holders and storage plates is impossible. The new X-ray mini technology expands the application of NDT. The examples of practical application of solid-state miniature transducers are presented.
Nowym kierunkiem radiografii jest radiografia błyskowa (ang. flash radiograpy, FR), która nie ma pośrednich nośników danych (błon i płyt pamięciowych). FR tworzy szybki obraz. Zapewnia niskie koszty testowania oraz możliwość monitorowania obiektów pod kątem błędów wewnętrznych w czasie rzeczywistym. W radiografii błonowej, jeśli względna gęstość fotometryczna jest większa niż 4, migawki stają się praktycznie nieczytelne i mogą być trudne do digitalizacji. Obecne technologie wolne od błon radiograficznych nie mają tej wady, a poza tym dają wyniki w formie cyfrowej bez specjalnych systemów do digitalizacji. Dane cyfrowe zawierają obrazy promieniowania z defektów wewnętrznych, rozszerzają możliwości wykrywania wad i zmniejszają koszty testowania. Promieniowanie błyskowe jest oparte na przenośnym aparacie rentgenowskim, który umożliwia obserwację wyników badań rentgenowskich na ekranie monitora. Można przeprowadzić badanie wad wewnętrznych pod różnymi kątami. Promieniowanie błyskowe z cyfrowymi przetwornikami półprzewodnikowymi jest najbardziej perspektywiczne z czułością na poziomie do 0,1% badanej grubości metalu przy rozdzielczości przekraczającej 10 par linii na mm. Zastosowanie przenośnych przetworników półprzewodnikowych o niewielkich rozmiarach otwiera nowe możliwości technologiczne. Można je lokalizować i przemieszczać w strefach, w których nie jest możliwe pozycjonowanie uchwytów błon i płyt do przechowywania. Nowa mini technologia rentgenowska rozszerza zastosowanie NDT. Przedstawiono przykłady praktycznego zastosowania miniaturowych przetworników półprzewodnikowych.
Źródło:
Badania Nieniszczące i Diagnostyka; 2018, 2; 29-34
2451-4462
2543-7755
Pojawia się w:
Badania Nieniszczące i Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Multiboard trigger link synchronization and diagnostics
Autorzy:
Wojenski, A.
Pozniak, K.
Mazon, D.
Chernyshova, M.
Powiązania:
https://bibliotekanauki.pl/articles/114174.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
data quality monitoring
FPGA
GEM detector
soft X-ray plasma diagnostics
trigger distribution
measurement system
Opis:
Soft X-ray (SXR) plasma measurements are important type of diagnostics especially in tokamak facilities. Main output products are energy and topology spectra distributed in time. In case of Gas Electron Multiplier (GEM) detectors, used as radiation sensors, large number of analog readout channels must be provided. For this purpose Field-Programmable Gate Arrays (FPGAs) are used. Data quality monitoring (DQM) is important topic in case of asynchronous events registered by the measurement unit. Due to numerous FPGAs used it is necessary to provide advanced trigger synchronization between them. In the paper is proposed an algorithmic approach for the trigger link training and diagnostics. It is a key component in order to provide consistent measurement data for DQM analysis. The contents of the article covers the plasma experiments and related DQM topics. In following chapters explanation of the synchronization problem is described. The proposed algorithm will be used for trigger link synchronization and diagnostics aspects. The simulations are also discussed. Currently, the proposed ideas are at the stage of implementation and tests on real hardware. Simulation were successfully performed. Summary of the work carried out is presented at the end of the paper.
Źródło:
Measurement Automation Monitoring; 2017, 63, 6; 223-225
2450-2855
Pojawia się w:
Measurement Automation Monitoring
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dyfrakcyjny pomiar naprężeń w testach tribologicznych elementów z powłokami niskotarciowymi
Diffraction measurement of residual stresses in tribological tests of elements covered with low friction coatings
Autorzy:
Stachura, K.
Kalbarczyk, M.
Szczerek, M.
Tuszyński, W.
Powiązania:
https://bibliotekanauki.pl/articles/188300.pdf
Data publikacji:
2015
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
dyfrakcja rentgenowska
powierzchniowe zużycie zmęczeniowe (pitting)
naprężenia
X-ray diffraction
rolling contact fatigue (pitting)
residual stresses
Opis:
W artykule przedstawiono założenia metodyczne wyznaczania naprężeń w warstwie wierzchniej elementów poddawanych tribologicznym testom zmęczeniowym. Elementami tymi były próbki o kształcie stożka wykonane ze stali łożyskowej 100Cr6, szybkotnącej SW7M, bez powłoki i z powłoką niskotarciową WC/C oraz stożki ze stali 100Cr6 pokryte powłoką DLC. Zaproponowane podejście obejmuje szereg pomiarów stanu naprężeń wokół śladu współpracy elementów trących. Do wyznaczania rozkładu naprężeń zastosowano dyfrakcyjną metodę sin2ψ, wykorzystywaną dotychczas w nauce i przemyśle przede wszystkim do oceny poprawności procesów technologicznych, zwłaszcza pod kątem uzyskiwanej wytrzymałości obrabianych elementów.
The aim of this article was to present the methodological assumptions of determining residual stresses in the surface layer of components undergoing tribological tests. The presented approach to residual stresses measurements includes a series of measurements conducted through the middle of the specimen friction track. The sin2ψ diffraction method, which is widely used in science and industrial sectors, was applied to determine the distribution of residual stresses. The cone-shaped samples from bearing steel 100Cr6 and high-speed steel SW7M were tested. By means of developed method the authors analysed the influence of WC/C and DLC coating deposition on the residual stresses of steel samples. The aplication of develped method makes it possible to determine the changes of residua stresses in the tribological samples.
Źródło:
Tribologia; 2015, 6; 105-112
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Nieniszczące badania struktury materiałów włóknisto-cementowych z użyciem tomografii komputerowej
Non-destructive testing of fibre-cement structure materials using computer tomography
Autorzy:
Schabowicz, K.
Matuszewski, M.
Nierösel, B.
Schlößer, D.
Powiązania:
https://bibliotekanauki.pl/articles/107937.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
badania nieniszczące
płyty włóknisto-cementowe
tomografia komputerowa
non-destructive testing
fiber-cement board
x-ray computer tomography
Opis:
W artykule przedstawiono analizę badań nieniszczących płyt włóknistocementowych metodę tomografii komputerowej. Badaniom poddano 5 rodzajów płyt włóknisto-cementowych: płyta wewnętrzna, elewacyjna, elewacyjna barwiona w masie, wewnętrzna barwiona w masie i wodoodporna. Otrzymano rezultaty badań pozwoliły zaobserwować mikrostrukturę badanych płyt i odnieś wyniki do badań metalograficznych jak i do innych badań nieniszczących.
The paper presents a proposal of fibre-cement boards testing using nondestructive x-ray computed tomography. Five types of fibrous-cement boards were tested: internal, facade, façade colored, interior colored and waterproof. Interesting research results have been obtained which have allowed us to observe the microstructure of the examined boards.
Źródło:
Badania Nieniszczące i Diagnostyka; 2017, 3; 3-5
2451-4462
2543-7755
Pojawia się w:
Badania Nieniszczące i Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Tomografia komputerowa w pomiarach geometrycznych 3D
Computed tomography in 3D geometrical measurements
Autorzy:
Ratajczyk, E.
Powiązania:
https://bibliotekanauki.pl/articles/151191.pdf
Data publikacji:
2011
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
tomografia komputerowa-TC
lampa rentgenowska
promieniowanie X
współrzędnościowa technika pomiarowa
computed tomography CT
detector
coordinate measuring systems
X-rays radiations
rotary tables
X-ray tube
Opis:
Istota pomiarów tomograficznych opartych na promieniowaniu rentgenowskim X. Budowa tomografów - główne zespoły i ich funkcje. Kalibracja tomografów. Prezentacja modelu tomografu opracowanego w Instytucie Metrologii i Inżynierii Biomedycznej.
Computed tomography (CT), after its dynamical development for medical requirements recently starts to appear in an area of industrial applications. It enables not only to determine dimensions of objects made of metal, plastics and different kinds of composed materials but also to defect internal defects of the material. This paper describes concepts of CT measurements. The main construction units of tomographs are characterized and the examples of tomographs of different firms and their applications are given. The accuracy and calibration problems are also shortly discussed. At the and the concepts of home - made computed tomograph for industrial applications are also presented.
Źródło:
Pomiary Automatyka Kontrola; 2011, R. 57, nr 2, 2; 220-223
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Sterowanie dynamiką kolimatora z ferrofluidem w formowaniu widma wiązki diagnostycznej i redukcji wad obrazów RTG
Control of ferrofluid collimator dynamics in shaping diagnostic beam spectrum and reduction of X-ray image defects
Autorzy:
Dyszkiewicz, A.
Kępiński, P.
Połeć, P.
Chachulski, D.
Nowak, E.
Powiązania:
https://bibliotekanauki.pl/articles/158574.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
inkoherencja promieni X
kolimacja wiązki diagnostycznej
soczewka Fresnela
soczewka z ferrofluidu
incoherence of primary X-ray beam
collimation of diagnostic beam
Fresnel lens
ferrofluid lens
Opis:
W opracowaniu zwrócono uwagę na inkoherencję pierwotnych wiązek promieni X, powstających w aktualnie dostępnych lampach RTG, wpływających na powstawanie zniekształceń geometrycznych i gradientowych radiogramów. W celu uzyskania wiązki diagnostycznej, złożonej wyłącznie z promieni osiowych i przyosiowych stosuje się kolimatory z materiałów metalicznych, eliminujących w procesie formowania powyżej 90% energii promieniowania lampy. Zupełnie nowym podejściem było zastosowanie systemów filtrująco-refrakcyjnych, charakteryzujących się znacznie mniejszą stratnością, niestety nie dysponujących możliwością przestrajania profilu parametrycznego. W praktyce daje to możliwość przekierowania promieni pozaosiowych, do użytecznego obszaru przyosiowego. Celem programu było zaprojektowanie i budowa systemu refrakcyjno-filtrującego, zaopatrzonego w przetwornik zdolny do sterowanych zmian swej struktury, a w konsekwencji geometrii promieni pozaosiowych. Celem technicznym pracy była budowa urządzenia prototypowego, z cyfrowo-analogowym systemem sterowania oraz jego testy laboratoryjne mające odpowiedzieć na pytania, czy ruch wirowy ferrofluidu w polu magnetycznym wpływa na geometrię i rozkład energii w kącie bryłowym wiązki promieniowania X oraz jaki występuje tu rodzaj korelacji z prędkością obrotową? Na podstawie analizy wyników badań stwierdzono wpływ prędkości obrotowej oraz objętości ferrofluidu na zdolność do refrakcji promieni X, o charakterze nieliniowym oraz zaobserwowano możliwość sterowania cechami geometrycznymi podłoża, powodując doosiowe przesunięcie widma rozkładu energetycznego w kącie bryłowym wiązki. W praktyce daje to możliwość wygodnej modyfikacji morfologicznych cech zdjęcia już na etapie ekspozycyjnym, powodując np. wyostrzenie anatomicznych szczegółów tkanek miękkich, z wygaszeniem obrazu tkanki kostnej lub odwrotnie.
The incoherence of primary X ray beams formed by currently avail-able devices, leading to geometric and gradient distortions of radiographs, has been pointed out in the study. In order to obtain a diagnostic beam made up exclusively of axial and paraxial rays, collimators with metallic materials are used, which eliminate over 90% of the radiant energy produced by the X-ray tube. A completely new approach is the use of refractory-filtering systems, which are characterised by much smaller loss, but feature a fixed parametric profile. In practice this enables the redirection of off-axis rays towards the focal plane. The intention of the study was to design and construct a refractory-filtering system capable of controlled alteration of off-axis ray geometry. The purpose of the laboratory work was the construction of a prototype device, with a digital and analogue control system, and test it to see whether the ferrofluid vortex motion induced by the magnetic field affected the geometry and distribution of energy within a solid angle of an x-ray beam as well as to determine the type of correlation with the rotational speed. On the basis of the analysis of the study results, it was found that the rotational speed and volume of the ferrofluid impacted the non-linear X-ray refraction capability. It was also observed that the geometric features of the substrate could be controlled, leading to a shift of the rays towards the axis. In practice, this makes it possible to conveniently modify the morphological characteristics of an image already at the exposure stage, thus sharpening the anatomical details of the soft tissues, while suppress-ing the image of the bone tissue, or vice versa.
Źródło:
Pomiary Automatyka Kontrola; 2014, R. 60, nr 4, 4; 207-211
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Tomografy przemysłowe CT - rodzaje, parametry, zastosowania, testy dokładności
CT industrial tomographs - parameters, applications, test accuracy
Autorzy:
Ratajczyk, E.
Powiązania:
https://bibliotekanauki.pl/articles/153553.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
tomograf komputerowy CT
lampa rtg
model CAD
inżynieria odwrotna
CT
computer tomography
X-ray tube
CAD model
reverse engineering
accuracy tests
Opis:
Wyjaśniono zasadę budowy i działania tomografu komputerowego CT - wyszczególniono główne zespoły i ich funkcje. Zamieszczono przykład tomografu i jego parametry. Pokazano możiiwości pomiarowe tomografów, a na końcu zaprezentowano parametry charakteryzujące dokładność podając przykład wyznaczenia dokładności tomografu METROTOM za pomocą specjalnie zbudowanego wzorca.
The principle of construction and operation of a CT scanner is explained. Major units and their functions are specified. The construction and operation of an X-ray tube as well as the positioning system associated with mounting of a measured object are described. The principle of construction and operation of a matrix (panel) of detectors is explained. Examples of scanners and their parameters are included. Measurement capabilities of tomographs, including options such as standard geometry of dimensions with respect to the CAD model or reverse engineering if the CAD model is not available, are shown. Also the possibility to capture material discontinuities, inclusions of impurities, bubbles, in terms of the so-called defectoscopy, is shown. Finally, the parameters characterizing the accuracy are presented. These parameters include: the parameter associated with the error of the length measurement - E, the parameters associated with the scanning error - PF, PS, the parameters defining the dimensions and material dependencies - GS, GF, GG, the parameter specifying the resolution - Dg. The parameters associated with the error of the length measurement are explained based on the accuracy verification for a METROTOM tomograph with the use of a specially built artefact.
Źródło:
Pomiary Automatyka Kontrola; 2014, R. 60, nr 9, 9; 713-717
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of Fly Ash Concrete With Scanning Electron Microscopy and X-Ray Diffraction
Autorzy:
Uzbaş, Burhan
Aydın, Abdulkadir Cüneyt
Powiązania:
https://bibliotekanauki.pl/articles/103299.pdf
Data publikacji:
2019
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
fly ash
microstructure of concrete
scanning electron microscopy
x-ray diffraction
calcium hydroxide
popiół lotny
mikrostruktura betonu
skaningowa mikroskopia elektronowa
dyfrakcja rentgenowska
wodorotlenek wapnia
Opis:
In this study, the effects of using different ratios of fly ash on hydration products as well as the mechanical and microstructural properties of hardened concrete were investigated. Portland cement was replaced with 5%, 10%, 15% and 20% fly ash (FA) by weight. The microstructural properties of the obtained samples were investigated by means of X-ray diffraction (XRD) and Scanning electron microscopy (SEM). Fly ash has negative effect on 7 days concrete strength; however, it was seen that fly ash increases the compressive strength of 28 and 90 days concrete. The XRD analysis showed that the ratio of calcium hydroxide (CH), which is produced by hydration, decreases depending on the concrete age and the amount of fly ash. The SEM analysis showed that the usage of fly ash decreases gaps and increases C-S-H which is also a hydration production. When Portland cement was replaced with 10% fly ash by weight, compressive strength has increased and microstructure of concrete has improved. The reason for this is filling of gaps by fly ash and the decrease in the amount of Ca(OH)2 due to the reaction between fly ash and Ca(OH)2. Within this scope, the development in microstructure of fly ash concrete was evaluated in 90 days duration and a change of the development with compressive strength was investigated.
Źródło:
Advances in Science and Technology. Research Journal; 2019, 13, 4; 100-110
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ warunków dyspergowania montmorylonitu w żywicy epoksydowej na właściwości mechaniczne i morfologię nanokompozytów
Influence of the dispergation conditions of montmorylonite in epoxy resin on the mechanical properties and morphology of nanocomposites
Autorzy:
Pawelec, Z.
Kostrzewa, M.
Bakar, M.
Powiązania:
https://bibliotekanauki.pl/articles/189836.pdf
Data publikacji:
2011
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
nanokompozyt
montmorylonit (MMT)
dyspergowanie mechaniczne
ultradźwięki
właściwości mechaniczne
dyfraktometria rentgenowska (WAXS)
nanocomposite
montmorylonite (MMT)
mechanical dispergation
ultrasounds
mechanical properties
wide angle X-ray scattering (WAXS)
Opis:
W pracy przedstawiono wyniki badań właściwości mechanicznych i morfologii nanokompozytów polimerowych z osnową epoksydową i glinokrzemianem. Jako napełniacz zastosowano montmorylonit (MMT) Closite 30B. Stwierdzono, że jego obecność korzystnie wpływa na właściwości mechaniczne żywicy epoksydowej. Zastosowano kilka sposobów dyspergowania MMT w żywicy epoksydowej: dyspergowanie mechaniczne, (prędkość obrotowa 9500 i 20500 obr./min), dyspergowanie ultradźwiękowe (amplituda 50 i 100%) oraz metodę skojarzoną łączącą dyspergowanie mechaniczne i ultradźwiękowe (prędkość 9500 obr./min, amplituda 100%). Czas dyspergowania był jednakowy dla wszystkich metod (10 min). Właściwości wytrzymałościowe nanokompozytów zależą istotnie od sposobu dyspergowania napełniacza. Wyniki badań otrzymane za pomocą skaningowej mikroskopii elektronowej (SEM) i szerokokątowej dyfraktometrii rentgenowskiej (WAXS) wskazują, że uzyskano równomierne zdyspergowanie napełniacza i exfoliację warstw glinokrzemianu.
The paper presents of the investigation of mechanical properties and morphology of epoxy matrix nanocomposites. Montmorylonite (MMT) Closite 30B was used as aluminosilicate nanofiller. It has been found that presence of nanofiller has a beneficial effect on the mechanical properties of epoxy resin. Some methods of dispegation of MMT in epoxy resin were used: mechanical dispergation (9500 and 20500 rpm), ultrasonic dispergation (amplitude of 50 and 100%). Dispergation time (10 min) was the for all used methods. The mechanical strength of nanocomposites depends significantly on the method of dispergation. Results os Scanning Elektron Microscopy (SEM) and Wide Angle X-ray Scattering (WAXS) investtigations show that the nanofiller has been uniforly dispergated and the exfoliation of aluminosilicate layers has taken place.
Źródło:
Tribologia; 2011, 5; 169-180
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie składu chemicznego warstw granicznych powstających z udziałem ekologicznego środka smarowego
An investigation of the chemical composition of boundary layers formed in the presence of synthetic lubricant
Autorzy:
Makowska, M.
Powiązania:
https://bibliotekanauki.pl/articles/190747.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
rentgenowska spektroskopia fotoelektronów XPS
olej syntetyczny
poli-α-olefiny
ekologiczny dodatek uszlachetniający
właściwości przeciwzużyciowe
X-Ray Photoelectron Spectroscopy
synthetic oil
poly-α-olefins
ecological additive
antiwear properties
Opis:
Zbadano skład chemiczny warstw granicznych powstających na powierzchni stali smarowanej podczas tarcia (w układzie kula-tarcza) olejem syntetycznym (PAO-4), zawierającym ekologiczny dodatek przeciwzużyciowy pochodzenia roślinnego. Do tego celu zastosowano rentgenowską spektroskopię fotoelektronową (XPS). Na roboczej powierzchni tarcia rejestrowano widma fotoelektronów, głównie żelaza, węgla i tlenu. Mikrostrukturę warstw wierzchnich badano po uprzednim trawieniu jonowym wybranych obszarów roboczej powierzchni tarcia. Stwierdzono, że w wyniku zachodzących przemian powstają produkty organiczne. Skład chemiczny odkładanych warstw zmieniał się wraz z głębokością wytrawiania. W kolejnych warstwach odkrywanych podczas bombardowania roboczej powierzchni tarcia atomami Ar+ wraz ze spadkiem zawartości węgla następował wzrost zawartości żelaza.
This paper presents an investigation of the chemical structure of boundary layers forming on steel surface during friction (ball-on-disc system) lubricated with synthetic oil (PAO-4), containing an ecological (vegetable-originated) antiwear additive. Sliding surfaces have been examined by X-ray Photoelectron Spectroscopy (XPS) – Fe2p, C 1s and O1s profiles were recorded. Investigated surfaces were subjected to an ion sputtering (Ar+). The research concludes that some organic compounds are layered in the sidling contact area. The chemical composition of the layers varied along with the sputter depth. In consecutive uncovered layers, iron content increased and the carbon content decreased simultaneously.
Źródło:
Tribologia; 2013, 4; 85-94
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Advanced Materials & Technologies in Precisive Temperature Measurements
Zaawansowane materiały i technologie w precyzyjnych pomiarach temperatury
Autorzy:
Prokhorenko, S.
Mudry, S.
Panas, A. J.
Stadnyk, B
Kowalczyk, A.
Powiązania:
https://bibliotekanauki.pl/articles/154994.pdf
Data publikacji:
2006
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
stopy eutektyczne Cd-Sn
Bi-Cd
dyfrakcja rentgenowska
różniczkowa kalorymetria skaningowa
temperaturowy punkt odniesienia
obróbka energetyczna
Cd-Sn
eutectic melts
X-ray diffraction
differential scanning calorymetry
temperature fix-point
energetical treatment
Opis:
The studies of eutectic melts Cd-Sn, Bi-Cd are carried out be means of X-ray diffraction, metallography and differential scanning calorymetry methods in order to check the possibility to use them as temperature fix-point. It is shown that outside energetic influence on melt can change some parameters of structure and physical properties.
Stopy eutektyczne Cd-Sn, Bi-Cd badane były metodami dyfrakcji rentgenowskiej, metalografii oraz różniczkowej kalorymetrii skaningowej w celu uzyskania wiedzy o możliwości używania ich jako temperaturowych punktów odniesienia. Wykazano, że zewnętrzna obróbka energetyczna stopów zmienia ich parametry strukturalne i właściwości fizyczne.
Źródło:
Pomiary Automatyka Kontrola; 2006, R. 52, nr 12, 12; 4-6
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ temperatury na skład chemiczny warstw granicznych powstających z udziałem dodatku smarnego pochodzenia roślinnego
Influence of elevated temperature on the chemical composition of boundary layers forming in the presence of an antiwear additive of vegetable origin
Autorzy:
Makowska, M.
Powiązania:
https://bibliotekanauki.pl/articles/189676.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
warstwa graniczna
dodatek przeciwzużyciowy
dodatek pochodzenia roślinnego
poli-α-olefiny
tribochemia
rentgenowska spektroskopia fotoelektronów XPS
boundary layer
antiwear additive
additive of vegetable origin
poly-α-olefins
tribochemistry
X-Ray Photoelectron Spectroscopy (XPS)
Opis:
Zbadano wpływ temperatury na skład chemiczny warstw granicznych powstających na powierzchni stali podczas tarcia z udziałem oleju poli-α-olefinowego zawierającego dodatek przeciwzużyciowy pochodzenia roślinnego. Strukturę powstających warstw badano za pomocą rentgenowskiej spektroskopii fotoelektronowej (XPS). Stwierdzono, że wzrostowi temperatury podczas tarcia towarzyszy zwiększenie intensywności przemian tribochemicznych, przejawiające się wzrostem grubości warstwy produktów, odłożonych na roboczej powierzchni tarcia.
The effect of temperature on the chemical structure of boundary layers forming on steel surface during friction lubricated by poli-α-olefin oil containing antiwear additive of vegetable origin are investigated. The use of X-ray Photoelectron Spectroscopy (XPS) to analyse the surface of contact region showed evidence of the formation products of tribochemical reactions. Based on the results obtained for elevated temperature and previous results relating to ambient temperature, it is seen that thickness of the surface layer is significantly influenced by evaluated temperature, which changes the intensity of the proceeding reactions.
Źródło:
Tribologia; 2013, 5; 45-54
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-13 z 13

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies