Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "process," wg kryterium: Temat


Tytuł:
Comparative analysis of methane concentration near the junction of the longwall and top road
Autorzy:
Zmarzły, Marian
Trzaskalik, Paweł
Powiązania:
https://bibliotekanauki.pl/articles/409850.pdf
Data publikacji:
2019
Wydawca:
STE GROUP
Tematy:
process
process management
process improving
quality management methods
Opis:
Mining of longwalls ventilated by the „U” method is willingly applied in Polish coal-mines due to low costs of workings maintenance, low costs of ventilation and a lower fire threat because of a limited flow of air through goafs. However, such a way of ventilation may pose an increased risk of methane explosion. For this reason, the “U” ventilation has been limited in longwalls with methane risk. The mining regulations in force provide that ventilation methane-bearing capacity, i.e. the intensity of methane flow into the ventilation air cannot exceed 20 m3 CH4/min. The regulations also provide that in the event the absolute methane-bearing capacity, i.e. a sum of methane released to the ventilation air and captured by the methane drainage system is higher than 25 m3 CH4/min and the “U” method of ventilation is applied, the effectiveness of methane drainage should be minimum 50% in relation to the forecast absolute methane-bearing capacity. To streamline the process of ventilation near the junction of the longwall and the gallery carrying off the used air, auxiliary ventilation means are applied, such as a ventilation partition, a ventube – which supplies air without methane or with a low concentration of methane, injectors etc. Application of these means is limited by the cross-section of the heading carrying off the air from the longwall. Deformations of the ventilating roadway, which is usually located in the one-sided vicinity of goafs, may prevent the use of a ventilation partition, which has a negative influence on the conditions of ventilating the junction of the longwall and ventilating roadway. The author of the article also refers to such conditions, presenting average values and maximum concentrations of methane concentrations recorded with four methane concentration sensors, located in the vicinity of the junction of the longwall and ventilating roadway.
Źródło:
Management Systems in Production Engineering; 2019, 3 (27); 166-173
2299-0461
Pojawia się w:
Management Systems in Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of selected methods and approaches for improvement of processes and their use in practice in companies of wood processing industry in Slovakia
Autorzy:
Simanová, Ľubica
Gejdoš, Pavol
Powiązania:
https://bibliotekanauki.pl/articles/409623.pdf
Data publikacji:
2019
Wydawca:
STE GROUP
Tematy:
process
process management
process improving
quality management methods
Opis:
The aim of the paper is to point out the principles of process management and selected quality management tools, which are aimed at improving the processes of the wood processing industries of the Slovak Republic. The knowledge from these areas is based on the analysis of the theoretical origins from domestic and foreign sources and supported by the results of the research carried out in the first half of the year 2017. In the processing of the results, classical methods of research work were used such as analysis, synthesis, comparison, descriptive statistics, contingency tables, chi-quadrat test and graphic depiction. Based on the analysis of the research results, there was a slight dependence between the process optimization levels in the timber industry and other process improvement methods such as statistical process control methods and graphical analysis and problem solving tools.
Źródło:
Management Systems in Production Engineering; 2019, 3 (27); 162-165
2299-0461
Pojawia się w:
Management Systems in Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie wpływu systemu zarządzania jakością na procesy w organizacji
The examination of the impact on the processes of the quality management system in the organization
Autorzy:
Książek, D.
Ligarski, M.
Powiązania:
https://bibliotekanauki.pl/articles/113341.pdf
Data publikacji:
2016
Wydawca:
STE GROUP
Tematy:
proces
podejście procesowe
process
process approach
Opis:
W artykule zaprezentowano elementy poszczególnego procesu, przedstawiono rolę podejścia procesowego oraz możliwości jakie daje jego wdrożenie w organizacji. Podjęto również próbę określenia wpływu systemu zarządzania jakością na procesy w organizacjach mających wdrożony system zarządzania jakością. Analiza została przeprowadzona w oparciu o przeprowadzone badania własne z udziałem pracowników przedsiębiorstw branży wodno-kanalizacyjnej.
The article shows the individual process, show the role of the procedural approach and the opportunities offered by its implementation In the organization. It was also an attempt to determine the impact on the process of the quality management system in organizations that have implemented quality management system. The analysis was carried out on the basis of the carried out research involving plumbing industry workers.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2016, 2 (14); 190-198
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microtools Based on the Relational Data Model – Conformity between Foreign and Primary Keys
Autorzy:
Szczęśniak, B.
Powiązania:
https://bibliotekanauki.pl/articles/2064919.pdf
Data publikacji:
2018
Wydawca:
STE GROUP
Tematy:
spreadsheet
database
business process improvement
information process
Opis:
Tools which support and automate the execution of information processes may be created in a spreadsheet by following the author’s signature concept of “Microtools Based on the Relational Data Model”. While developing them, one must apply adequate solutions enabling representation of identified entities and ensuring data integrity as well as acquisition of the reports and collations assumed to be generated. This article addresses the problem of conformity between values of foreign keys in child entities and values of primary keys in parent entities. Four cases of relationships between a parent entity and a child entity have been discussed. One of the criteria that differentiates between these cases is the occurrence of a simple key or a composite key. Another applicable criterion is the sequence in which data are entered using the tool. With regard to all the identified cases, solutions that support data integrity have been presented and discussed. In accordance with the concept in question, the solutions proposed in the paper make use of standard spreadsheet features and components, without involving any additional code created in any programming language.
Źródło:
Multidisciplinary Aspects of Production Engineering; 2018, 1, 1; 491--497
2545-2827
Pojawia się w:
Multidisciplinary Aspects of Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Implementation of the Six Sigma methodology in increasing the capability of processes in the company of the furniture industry of the Slovak Republic
Autorzy:
Simanova, Ľubica
Gejdoš, Pavol
Powiązania:
https://bibliotekanauki.pl/articles/1537809.pdf
Data publikacji:
2021
Wydawca:
STE GROUP
Tematy:
process
capability
Six Sigma
process improving
quality
performance
Opis:
The aim of the article is to present the results of a case study focused on the implementation of the Six Sigma methodology in order to improve the quality and increase the efficiency of furniture production processes. Positive results of implementation after the implementation of corrective measures were achieved in the values of process capability coefficients, reduction of nonconformities and subsequent reduction of DPMO, increase of the values of the level of efficiency and sigma of the critical process.In the processing of the results, classical methods of research work were used such as analysis, synthesis, comparison, descriptive statistics, coefficients Cp a Cpk, DPMO, level of efficienty and sigma,and also graphic methods.
Źródło:
Management Systems in Production Engineering; 2021, 1 (29); 54-58
2299-0461
Pojawia się w:
Management Systems in Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Criteria for the optimization of production processes in machining of metallic materials
Autorzy:
Matisková, D.
Balog, M.
Husár, J.
Powiązania:
https://bibliotekanauki.pl/articles/410048.pdf
Data publikacji:
2018
Wydawca:
STE GROUP
Tematy:
production process
criteria
optimization process
machine tool
mathematical methods
Opis:
The paper deals with the optimization of production processes and the setting of criteria for reducing production costs. Any company is not just a leap in production, but a lean has to be gradually transferred to all its activities. This created the concept of a lean company first. The skill of an enterprise is to perform only the activities that are needed, to do them right for the first time, to make them faster than others and to spend less resources at the same time. The company's business is that the company does exactly what the customer wants, with a minimum number of activities that do not add value to the product or service. The Lean Production System focuses mainly on eliminating waste in every activity of the manufacturing enterprise.
Źródło:
Management Systems in Production Engineering; 2018, 4 (26); 227-230
2299-0461
Pojawia się w:
Management Systems in Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Hierarchical EPC models – review of model linking concepts
Autorzy:
Szczęśniak, Bartosz
Powiązania:
https://bibliotekanauki.pl/articles/2064927.pdf
Data publikacji:
2019
Wydawca:
STE GROUP
Tematy:
business process modelling
EPC
BPM
linking of process models
Opis:
EPC models are currently among the leading standard business process modelling solutions. As long as the rules for creating flat EPC models are explicit and raise no significant doubts, when it comes to linking models of different types, the literature of the subject delivers diversified solutions. Four such alternative concepts that can be applied in this respect have been identified and described in this article. They have been used to link EPC models for four cases proposed. These cases differ as to the degree of complexity, and they represent different kinds of potential links between processes being modelled. Using the concepts in question with reference to the cases defined has made it possible to identify situations in which it is impossible to link models, or when it raises certain doubts. What has also been proposed is that one of the concepts identified in the paper can be modified in such a manner that using it to link EPC models does not pose any problem in any of the cases discussed.
Źródło:
Multidisciplinary Aspects of Production Engineering; 2019, 2, 1; 476--486
2545-2827
Pojawia się w:
Multidisciplinary Aspects of Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Process Modelling Based on Event Logs
Autorzy:
Brzychczy, E.
Powiązania:
https://bibliotekanauki.pl/articles/2065023.pdf
Data publikacji:
2018
Wydawca:
STE GROUP
Tematy:
process modelling
process mining
event logs
Petri net
model discovery
Opis:
Process modelling is a very important stage in a Business Process Management cycle enabling process analysis and its redesign. Many sources of information for process modelling purposes exist. It may be an analysis of documentation related directly or indirectly to the process being analysed, observations or participation in the process. Nowadays, for this purpose, it is increasingly proposed to use the event logs from organization’s IT systems. Event logs could be analysed with process mining techniques to create process models expressed by various notations (i.e. Petri Nets, BPMN, EPC). Process mining enables also conformance checking and enhancement analysis of the processes. In the paper issues related to process modelling and process mining are briefly discussed. A case study, an example of delivery process modelling with process mining technique is presented.
Źródło:
Multidisciplinary Aspects of Production Engineering; 2018, 1, 1; 385--392
2545-2827
Pojawia się w:
Multidisciplinary Aspects of Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modified Resource-Constrained Project Scheduling to minimize idle time for Banbury mixing process: a case study in the tire manufacturing industry
Autorzy:
Butrat, Anan
Supsomboon, Srisawat
Powiązania:
https://bibliotekanauki.pl/articles/27315567.pdf
Data publikacji:
2023
Wydawca:
STE GROUP
Tematy:
RCPS
natural aging process
idle time
production scheduling
Banbury mixing process
Opis:
The Banbury mixing process (BMP) is to supplies the specific characteristic compounds for the tire manufacturing process. Idle time in the BMP was a problem caused by the aging process between mixing steps and the limited space for processing, measured in pallets. In this study, the resource-constrained project scheduling model (RCPS) is modified in case of the objective function and the input value of resource constraint to minimize idle time (SST). The complete minimization (Cmax) is changed from minimizing the starting time of the last job to the starting time of all jobs. In addition, the non-limited resource is defined as the input for the space capacity to reduce the idle time. As the results, the SST can provide the schedule that make less 5 time periods of idle time. Moreover, when considering the relationship between mixing and aging, aging process that is scheduled from SST starts immediately comparison to Cmax that some of aging process are not. Furthermore, the effect of the quantity of pallets was also examined. Although the non-limited resource does not make any delay to the schedule but the limited quantity is not. When pallets are limited, aging jobs were significantly impacted, with the last aging pallet being delayed. To reduce delays, it prepares an adequate supply of pallets that is close to or equal to its requirement that is defined by the non-limited resource. Further research combining the scheduling of the BMP with the tire manufacturing process and more techniques to modify RCPS are applied.
Źródło:
Management Systems in Production Engineering; 2023, 3 (31); 263--270
2299-0461
Pojawia się w:
Management Systems in Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Value Streams Mapping in the Implementation of Process Innovations – in the Case of Single–Unit Production
Autorzy:
Klimecka-Tatar, D.
Kapustka, K.
Powiązania:
https://bibliotekanauki.pl/articles/2064983.pdf
Data publikacji:
2018
Wydawca:
STE GROUP
Tematy:
value stream mapping
process innovation
process improvement
lean management
Kaizen philosophy
Opis:
The visual management technique used in process improvement, i.e. value stream mapping (VSM) has been presented in the paper. Value stream mapping is one of the basic management tools in the context of Lean Management or Lean Production. It allows to visualize the flow of decision, information, material and their connections in the full production cycle (from the order, through planning, production, to shipping to the customer). VSM is a lean tool that gives the ability to create flows in the process before implementing changes. In this paper, the possibilities of changes planning based on the current and future status maps have been discussed. On the basis of the current state map (CSM), the areas requiring improvement and operations which efficiency is decisive and for the process have been designated. Particular attention has been paid to the possibilities of using VSM in unit production processes. In the paper has been proposed the two possibilities for company development in terms of the improvement technique in line with the Kaizen philosophy as well as the implementation of process innovations. Which means balanced development through the improvement of the existing process or an acute development strategy through the implementation of process innovations (which involves significant costs).
Źródło:
Multidisciplinary Aspects of Production Engineering; 2018, 1, 1; 649--655
2545-2827
Pojawia się w:
Multidisciplinary Aspects of Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improvement of Production Processes with the Use of Lean Manufacturing Tools
Autorzy:
Furman, J.
Kuczyńska-Chałada, M.
Poloczek, R.
Powiązania:
https://bibliotekanauki.pl/articles/2064893.pdf
Data publikacji:
2018
Wydawca:
STE GROUP
Tematy:
process improvement
Lean Manufacturing
Opis:
Growing competition, clients’ requirements as well as advances in technology make modern industrial enterprises search for a way of achieving and maintaining strong position on the market. One of the principal and at the same time necessary conditions to achieve this aim is continuous development of all of the processes in order to fulfil various clients’ expectations. Enterprises make use of different concepts and management methods which in significant way upgrade ongoing processes by raising their efficiency. One of such is the concept of ‘lean’ production - Lean Manufacturing. Management according to Lean Management rules allows to produce more with the use of less resources - at the same time approaching the aim which is to deliver clients the exact product they want. The process of resources use limitation is not easy to perform however, the concept of Lean Manufacturing by the application of chosen tools allows successfully and effectively to introduce ‘lean’ model of management in an enterprise and undertaking following improvement activities in every of its field.
Źródło:
Multidisciplinary Aspects of Production Engineering; 2018, 1, 1; 529--535
2545-2827
Pojawia się w:
Multidisciplinary Aspects of Production Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Problemy w organizacji procesu usługowo-wytwórczego w układzie klient – lekarz stomatolog – technik dentystyczny
Problems in organization of the service and manufacturing process in the system patient - dentist - dental technician
Autorzy:
Klimecka-Tatar, D.
Powiązania:
https://bibliotekanauki.pl/articles/112961.pdf
Data publikacji:
2017
Wydawca:
STE GROUP
Tematy:
wizualizacja procesu
proces usługowy
przepływ informacji
process visualization
service process
information flow
Opis:
Realizacja procesów usługowych o charakterze specjalistycznych obarczona jest dużym zakresem wymagań i obowiązków, rozpoczynając od wymagań prawnych, szerokiej wiedzy specjalistycznej, poprzez doświadczenie, praktykę i zaangażowanie. W niniejszym artykule zaprezentowano problemy, jakie mogą wystąpić w przypadku realizacji usług, których powodzenie w znacznej mierze uzależnione jest od podprocesu wytwórczego – na przykładzie leczenia stomatologicznego wymagającego zaprojektowanie i wytworzenie protezy dentystycznej.
The implementation of specialized service processes is subject to a large range of requirements and obligations, starting with legal requirements, broad expertise, through experience, practice and commitment. This article presents the problems that may arise in the implementation of services whose success depends on the result of the manufacturing subprocess - on the example of dental treatment requiring the design and manufacture of dental prostheses.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2017, 6, 6; 141-148
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zasady ustalania mierników procesów w systemie zarządzania jakością
The rules of measurement QMS processes
Autorzy:
Molenda, M.
Powiązania:
https://bibliotekanauki.pl/articles/113656.pdf
Data publikacji:
2016
Wydawca:
STE GROUP
Tematy:
miernik procesów biznesowych
wskaźnik procesów biznesowych
business process measure
business process indicator
Opis:
W artykule opisano zasady budowy mierników procesów zidentyfikowanych i realizowanych w ramach systemu zarządzania jakością. W pierwszej części artykułu opisano wymagania normatywne w zakresie pomiaru procesów biznesowych oraz przedstawiono mechanizmy Doskonalenia organizacji wynikające z norm ISO serii 9000. W dalszej części opracowania scharakteryzowano proces biznesowy oraz opisano klasyfikację danych związanych z procesem, które można wykorzystać podczas definiowania mierników procesu. Zasadnicza cześć opracowania została poświęcona szczegółowym zasadom ustalania mierników procesów biznesowych w organizacji. Zasady zostały sformułowane w oparciu o badania poprawności mierników procesów stosowanych w 9. przedsiębiorstwach przemysłowych posiadających certyfikowany system zarządzania jakością.
This paper discusses issues related to the topic of ways of measurement of QMS process. In the first part the author describes the normatively requirements for measuring business QMS processes. In the second part of the paper the process of improvement of the organization according with the standards ISO 9000 is presented. Next autor presents issues related to the topic of business process management. In that part autor describes concept of business process and data related with it. The summary of the part is the characteristics of the four category data supporting the process measurement. In the main part of the text autor presents rules of establish the ways of measurement of QMS processes. The rules are based on the study conducted in nine selected Polish industrial companies.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2016, 2 (14); 249-257
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Use of Six Sigma in the production process - case study
Zastosowanie Six Sigma w procesie produkcyjnym – studium przypadku
Autorzy:
Midor, K.
Powiązania:
https://bibliotekanauki.pl/articles/113447.pdf
Data publikacji:
2017
Wydawca:
STE GROUP
Tematy:
Six Sigma
production process
quality
process improvement
proces produkcyjny
jakość
doskonalenie procesu
Opis:
Issues related to the quality of the final product and the individual components that comprise it are important in every branch of the industry. This is especially true for the automotive branch, where the consequences of quality errors are very severe and costly. The article presents the use of the Six Sigma method for the improvement of the process of height measurement of a controller board chip in a production stream for a premium-class client. The method used, which can be defined mathematically, allowed for minimising the causes for excessive rejection rates of the element in question, which was presented in the article.
Zagadnienia związane z jakością produktu finalnego i poszczególnych komponentów składających się na produkt końcowy są ważne w każdej branży. Szczególnie w branży motoryzacyjnej, gdzie konsekwencje błędów jakościowych są bardzo dotkliwe i kosztowne. Celem artykułu jest zaprezentowanie zastosowania metody Six Sigma do doskonalenia procesu pomiaru wysokości chipa na płytce kontrolera na strumieniu produkcyjnym dla klienta klasy Premium. Zastosowana metoda, którą można zdefiniować w sposób matematyczny, pozwoliła zminimalizować przyczyny zbyt wysokiego odrzutu wybranego elementu, co zostanie zaprezentowanie w artykule.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2017, 6, 4; 147-152
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Mapowanie funkcji systemu ERP na organizację przedsiębiorstwa metodą modelu strukturalnego
Mapping ERP functionality to enterprise organization using the structural model
Autorzy:
Dziemba, Ł.
Senczyna, S.
Powiązania:
https://bibliotekanauki.pl/articles/112769.pdf
Data publikacji:
2017
Wydawca:
STE GROUP
Tematy:
system informatyczny
ERP
modele procesów
procesy biznesowe
information system
process models
business process
Opis:
Funkcjonalność systemów informatycznych ERP pozwala objąć wszystkie obszary aktywności przedsiębiorstwa wspomaganiem. Stanowi to podstawę doskonalenia zarządzania przedsiębiorstwem oraz osiągania efektywności w realizacji potrzeb otoczenia. Modele procesów, przedstawione w publikacji, maja na celu lepsze wykorzystanie funkcjonalności systemów informatycznych ERP we wspomaganiu przedsiębiorstwa na przykładzie obsługi klienta. Modele procesów utworzone zostały z zastosowaniem analizy strukturalnej w modelowaniu procesów biznesowych.
The functionality of ERP systems allows you to cover all areas of the company's support activities. This is the basis for improving the management of the company and achieving efficiency in meeting the needs of the environment. Process models, presented in the publication, aim to make better use of the functionality of ERP systems in supporting the company on the example of customer service. Process models were created using structural analysis in business process modeling.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2017, 6, 6; 69-78
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies