Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "X-ray" wg kryterium: Temat


Tytuł:
Wideband spectral emission measurements from laser-produced plasma EUV/SXR source based on a double gas puff target
Autorzy:
Arikkatt, Antony Jose
Wachulak, Przemysław
Fiedorowicz, Henryk
Bartnik, Andrzej
Czwartos, Joanna
Powiązania:
https://bibliotekanauki.pl/articles/1849155.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Plasma Spectroscopy
X-ray coherence tomography
soft X-ray
Opis:
We present spectral emission characteristics from laser-plasma EUV/SXR sources produced by irradiation of < 1 J energy laser pulse on eleven different double stream gas puff targets, with most intense electronic transitions identified in the spectral range from 1 nm to 70 nm wavelength which corresponds to photon energy from 18 eV to 1240 eV. The spectra were obtained using grazing incidence and transmission spectrographs from laser-produced plasma emission, formed by the interaction of a laser beam with a double stream gas puff target. Laser pulses with a duration of 4 ns and energy of 650 mJ were used for the experiment. We present the results obtained from three different spectrometers in the wavelength ranges of SXR (1-5.5 nm), SXR/EUV (4-15.5 nm), and EUV (10-70 nm). In this paper, detailed information about the source, gas targets under investigation, the experimental setup, spectral measurements and the results are presented and discussed. Such data may be useful for the identification of adequate spectral emissions from gasses in the EUV and SXR wavelength ranges dedicated to various experiments (i.e. broadband emission for the X-ray coherence tomography XCT) or may be used for verification of magnetohydrodynamic plasma codes.
Źródło:
Metrology and Measurement Systems; 2020, 27, 4; 701-719
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Synthesis and Characterization of Co-Cs-Nd-Sr-Doped Perovskite-Rutile-Type Structure
Autorzy:
Smolinski, T.
Zhao, L.
Rogowski, M.
Wawszczak, D.
Olczak, T.
Brykala, M.
Powiązania:
https://bibliotekanauki.pl/articles/355628.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Synroc
X-ray diffraction
Rutherford backscattering
particle induced X-ray emission
Roentgen computed microtomography
Opis:
The perovskite type matrix is considered as solidification material for high-level radioactive waste. In this work the perovskite-rutile-type matrix doped by Co, Cs, Nd and Sr which simulate nuclear waste was prepared by sol-gel route. The material was characterized by several methods such as: X-ray diffraction, energy dispersive X-ray spectrometer, and particle induced X-ray emission combined with Rutherford backscattering spectrometry. The analyzes confirmed chemical composition Co-Cs-Nd-Sr-doped perovskite-rutile-type structure. A virtual model of the pellet`s structure was created non-destructively by Roentgen computed micro-tomography. The leaching tests confirmed high chemical resistance of the matrix.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 4; 1417-1423
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Calcium Ions on the Structure and Properties of LaMnO3
Autorzy:
Bara, M.
Dzik, J.
Feliksik, K.
Kozielski, L.
Wodecka-Duś, B.
Goryczka, T.
Zarycka, A.
Adamczyk-Habrajska, M.
Powiązania:
https://bibliotekanauki.pl/articles/353112.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
LCMO
ceramics
manganites
X-ray diffraction
SEM
Opis:
La0,7 Ca0,3 MnO3 polycrystalline were synthesized from La2 O3 , CaO and MnO2 powder mixture using a solid state reaction technique. The compound powders were obtained through the free sintering method at different temperatures and sintering times in order to study the influence of technological conditions on Ca doped La manganites. The most important physical features as structure, microstructure and morphology were described after X-ray diffraction investigation. Photographs of the specimen fractures were taken with SEM (scanning electron microscope) and they revealed high porosity of the tested material and great tendency for its grains to create agglomerates. Influence of doping and technological conditions on lattice parameters were studied by means of Rietvield analysis. The XRD measurements reveal that La0,7 Ca0,3 MnO3 has orthorhombic symmetry with Pnma space group.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 3; 1189-1195
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation Of Intermetallic Compounds In Sn-Cu-Ni Lead-Free Solders
Badanie związków międzymetalicznych w bezołowiowych stopach lutowniczych Sn-Cu-Ni
Autorzy:
Nagy, E.
Kristaly, F.
Gyenes, A.
Gacsi, Z.
Powiązania:
https://bibliotekanauki.pl/articles/353266.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
intermetallic
lead-free solder
X-ray diffraction
Opis:
Interfacial intermetallic compounds (IMC) play an important role in Sn-Cu lead-free soldering. The size and morphology of the intermetallic compounds formed between the lead-free solder and the Cu substrate have a significant effect on the mechanical strength of the solder joint. In the soldering process of Sn-Cu alloys, Cu6Sn5 intermetallic compounds are formed. The complex structural behaviour of Cu6Sn5 IMC is temperature- and composition-dependent and it is long since subject to scientific research. The Cu6Sn5 phase basically exists in two crystal structures: hexagonal η-Cu6Sn5 (at temperatures above 186°C) and monoclinic η’-Cu6Sn5 (at lower temperatures). In the presence of Ni in the solder, the η-η’ transformation does not occur, therefore, the η-Cu6Sn5 phase remains stable. In this study the role of Ni in the (Cu,Ni)6Sn5 intermetallic compound in Sn-Cu lead-free solders was examined. Sn-Cu alloys with different Cu content (0.5 to 1 mass%) were modified through Ni addition. The morphology of the intermetallic compounds of the modified Sn-Cu alloys was investigated by optical microscopy (OM) and scanning electron microscopy (SEM), the IMC phases were examined with X-ray diffraction method (XRD).
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1511-1515
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of X-Ray Diffraction to Analyse Phase Composition of Aluminium Alloys for Plastic Working
Autorzy:
Pachut, K.
Żelechowski, J.
Boczkal, S.
Powiązania:
https://bibliotekanauki.pl/articles/354144.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium alloys
X-ray diffraction
qualitative phase analysis
Opis:
An attempt was made to determine phase composition of commercial aluminium alloys using X-ray diffraction. Samples for phase composition analysis were selected from the group of aluminium alloys covered by the EN 573-3:2013 standard [1]. Representative samples were taken from eight groups of alloys with different chemical composition (at least one sample from each group). The diffraction intensity was measured with a standard X-ray diffractometer in Bragg-Brentano geometry in a way that allowed identification of the weakest diffraction peaks. As a results of the performed research it has been shown that X-ray phase analysis can be used to identify the matrix of aluminium alloys, Si and crystalline intermetallic phases such as Mg2Si, Al93.38Cu6.02Fe24Si16.27, Al4.01MnSi0.74, MgZn2, Al17 (Fe3.2Mn0.8)Si2, Al65Cu20Fe15, and Cu3Mn2Al. The detectability limit of the above-mentioned phases is better than 0.5%. The research has also shown that X-ray phase analysis is applicable in the investigation of phase transformations taking place in aluminium alloys.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 4; 1315-1319
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Application of the Mechanochemical Synthesis for the Preparation of Advanced Ceramics Based on Barium Titanate
Autorzy:
Garbarz-Glos, B.
Bąk, W.
Budziak, A.
Dulian, P.
Lisińska-Czekaj, A.
Czekaj, D.
Powiązania:
https://bibliotekanauki.pl/articles/351521.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
BaTiO3
mechanochemical synthesis
X-ray methods
dielectric properties
Opis:
In the present study, the lead-free BaTi1-x Zrx O3 (for x = 0, 0.05 and 0.15) ceramics were prepared by High-Energy Ball Milling and heat treatments. The performed X-ray, SEM and EDS measurements confirmed high purity, good quality and the expected quantitative composition of the obtained samples. The study of dielectric properties was performed by means of broadband dielectric spectroscopy at the frequency ranging from 0.1 Hz to 10 MHz. The obtained measurement data, analyzed in accordance with the Arrhenius formalism demonstrated the presence of relaxation type dielectric mechanisms. The impedance answer of studied ceramic materials indicated the presence of two relaxation processes: one with a dominant resistive component and the other with a small capacitive component. The observed dielectric relaxation process is temperature dependent and has a “non-Debye” character.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 4; 1391-1396
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
X-Ray Topography of the Subsurface Crystal Layers in the Skew Asymmetric Reflection Geometry
Autorzy:
Świątek, Z.
Fodchuk, I.
Powiązania:
https://bibliotekanauki.pl/articles/356405.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
x-ray topography
subsurface crystal layers
asymmetric reflection geometry
Opis:
The technique of X ray topography with the asymmetric reflection geometry of X-ray diffraction presented in this paper as useful tool for structural characterization of materials, particularly, epitaxial thin films and semiconductor multi-layered crystal systems used for the optoelectronic devices. New possibilities of this technique for a layer-by-layer visualization of structural changes in the subsurface crystal layers are demonstrated for semiconductors after various types of surface treatment, such as chemical etching, laser irradiation and ion implantation.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 4; 1931-1938
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Structure and Magnetocaloric Effect of MnCoGe Alloy Modified by Nb
Autorzy:
Kutynia, Karolina
Gębara, Piotr
Przybył, Anna
Powiązania:
https://bibliotekanauki.pl/articles/2125529.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnetocaloric effect
Heusler alloys
X-ray diffraction
magnetic measurement
Opis:
The aim of this work was to investigate the effect of partial substitution of Mn by Nb on structure and thermomagnetic properties in the (Mn, Nb)-Co-Ge alloy. The master alloys were prepared by arc-melting in an arc furnace with high purity of constituent elements under a low pressure of Ar. The prepared specimens were studied in as-cast state. The X-ray was performed by BRUKER D8 Advance diffractrometer with Cu Kα radiation. The analysis of the XRD pattern revealed coexistence of two orthorhombic phases with different lattice constants. The analysis of the temperature dependence of magnetizaton confirmed the XRD results and showed that produced material manifested two magnetic phase transitions corresponding to detected phases. The values of the Curie temperature were 275 and 325 K. The values of magnetic entropy change ∆SM equaled 3.30 and 2.13 J/(kg K), respectively for recognized phases. Biphase structure of produced material allowed to reach relatively high refigeration capacity 307 J/(kg). Moreover, the analysis of field dependences of magnetic entropy change (∆SM = CBn) allowed to construct temperature dependence of exponent n. The analysis of elaborated n vs. T curve confirmed biphasic structure of produced material.
Źródło:
Archives of Metallurgy and Materials; 2022, 67, 3; 879--883
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Correlation between Microstructure and Electrochemical Properties of Al-Si Alloys
Autorzy:
Minciuna, Mirabela G.
Vizureanu, Petrica
Jeż, Bartłomiej
Sandu, Andrei Victor
Nabiałek, Marcin
Achitei, Dragos C.
Powiązania:
https://bibliotekanauki.pl/articles/2134104.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium alloys
microstructure
X-ray diffraction
corrosion
Evans diagrams
Opis:
The composition and structural modification of aluminium alloys influence their strength, tribological properties and structural stability. The phase composition of the structure as well as the characteristics of the elementary cell of each identified phase was established by X-ray diffraction, and the main objective was to determine the compositional phases, microstructure and microcomposition of the alloy. Based on the cyclic voltammograms it can be said that on the OCP interval (+1.5 V… -1.1 V), after the breakthrough potential is an intensification of the anodic process by the pronounced increase of the current density, in these conditions the Al-Si alloy has low values which means that it has a better corrosion resistance.
Źródło:
Archives of Metallurgy and Materials; 2022, 67, 3; 1067--1070
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Method for Filling and Sharpening False Colour Layers of Dual Energy X-ray Images
Autorzy:
Dmitruk, K.
Mazur, M.
Denkowski, M.
Mikołajczak, P.
Powiązania:
https://bibliotekanauki.pl/articles/227318.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
X-ray imaging
image processing
false colour
object detection
Opis:
An X-ray scanning and image processing have a vast range of applications in the security. An image of a content of some package being passed for example to an airplane or to the court house may help to figure out if there are any dangerous objects inside that package and to avoid possible threatening situation. As the raw X-ray images are not always easy to analyze and interpret, some image processing methods like an object detection, a frequency resolution increase or a pseudocolouring are being used. In this paper, we propose a pseudocoloring improvement over material based approach. By addition of the edge detection methods we fill and sharpen colour layers over the image, making it easier to interpret. We demonstrate the effectiveness of the methods using real data, acquired from a professional dual energy X-ray scanner.
Źródło:
International Journal of Electronics and Telecommunications; 2016, 62, 1; 49-54
2300-1933
Pojawia się w:
International Journal of Electronics and Telecommunications
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of crystallization on the electrical resistance and structure of amorphous Fe-Co-Cr-B-Si alloys
Wpływ krystalizacji na oporność elektryczną i strukturę amorficznych stopów Fe-Co-Cr-B-Si
Autorzy:
Solomon, H.
Solomon, N.
Powiązania:
https://bibliotekanauki.pl/articles/355840.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
amorphous alloys
X-ray diffraction
electric resistivity
microhardness
annealing
Opis:
The goal of this paper is to present the influence of temperature variation and iron substitution with Co on the structure and electrical properties of amorphous Fe75-xCoxCr1B7Si17 alloys (where x=1, 4, 7, and 10 at.%), obtained by melt-spinning technique. The electrical resistivity of the samples was measured by using a usual four-probe method from -160°C to 750°C. The electrical resistivity was also measured at room temperature for the amorphous Fe75-xCoxCr1B7Si17 ribbons annealed at various temperatures for different holding time. The annealed samples were also investigated by Vickers microhardness test. The amorphous structure of tested materials was examined by X-ray diffraction (XRD), Mőossbauer spectroscopy, differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) methods. Experimental results confirmed the utility of applied investigation methods and the influence of the Co content and annealing process on the crystallization, structure and electrical properties of examined amorphous alloys.
Celem niniejszego artykułu jest przedstawienie wpływu zmian temperatury i zastąpienia Fe przez Co na strukturę i właściwości elektryczne amorficznych stopów Fe75-xCoxCr1B7Si17 (gdzie x=1, 4, 7, 10 at.%) odlewanych na wirującym dysku. Oporność elektryczna próbek była mierzona metoda czteropunktowa w zakresie od -160°C to 750°C. Oporność elektryczna zmierzono także w temperaturze pokojowej dla amorficznych taśm Fe75-xCoxCr1B7Si17 wyżarzonych w różnych temperaturach dla różnych czasów. Wyżarzone próbki poddano również badaniom mikrotwardości Vickersa. Amorficzna strukturę badanych materiałów badano przy użyciu dyfrakcji rentgenowskiej (XRD), spektroskopii Mőossbauera, różnicowej kalorymetrii skaningowej (DSC) oraz skaningowej mikroskopii elektronowej (SEM). Wyniki eksperymentu potwierdziły przydatność zastosowanych metod badawczych oraz wpływ zawartości Co i wyżarzania na proces krystalizacji, strukturę i własciwości elektryczne badanych stopów amorficznych.
Źródło:
Archives of Metallurgy and Materials; 2012, 57, 4; 1031-1039
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Surface Modification of Self-Consolidated Microporous Ti Implant Compacts Fabricated by Electro-Discharge-Sintering in Air
Autorzy:
Jo, Y. J.
Yoon, Y. H.
Kim, Y. H.
Chang, S. Y.
Kim, J. Y.
Lee, Y. K.
Van Tyne, C. J.
Lee, W. H.
Powiązania:
https://bibliotekanauki.pl/articles/356790.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
titanium
implant
porous
sintering
X-ray photoelectron spectroscopy (XPS)
Opis:
A single pulse of 0.75-2.0 kJ/0.7g of atomized spherical Ti powders from 300 mF capacitor was applied to produce a microporous Ti implant compact by electro-discharge-sintering (EDS). A solid core in the middle of the compact surrounded by a microporous layer was found. X-ray photoelectron spectroscopy was employed to study the surface characteristics of the EDS Ti compact and it revealed that Ti, C and O were the main constituents on the surface with a smaller amount of N. The surface was lightly oxidized and was primarily in the form of TiO2 resulting from the air oxidation during EDS processing. The lightly oxidized surface of the EDS compact also exhibited Ti nitrides such as TiN and TiON, which revealed that the reaction between air constituents and the Ti powders even in times as short as 128 msec.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1287-1291
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Annealing, Stoichiometry, and Surface on Magnetism of (Pr,Dy)FeCoB Microparticles Ensemble
Autorzy:
Kablov, E. N.
Ospennikova, O. G.
Kunitsyna, E. I.
Piskorskii, V. P.
Korolev, D. V.
Morgunov, R. B.
Powiązania:
https://bibliotekanauki.pl/articles/356579.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
rare earth metals
magnets
magnetisation
Mössbauer spectroscopy
X-ray spectroscopy
Opis:
Magnetic properties of powder (Pr,Dy)FeCoB ferrimagnetic alloys and effects of annealing, surface states were analyzed. X-ray photoelectron spectroscopy and Mössbauer spectra of powders indicate the effect of surface states on phase composition and magnetic properties of the studied powder, if particles average size is smaller than 10 μm. Effect of stoichiometry on magnetic anisotropy was found. Thermal stability of anisotropy field was proved by replacement of Fe atoms with Co atoms.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 3; 1923-1930
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Ceramic Coating on Mechanical Properties of Stainless Steel
Autorzy:
Czekaj, D.
Lisińska-Czekaj, A.
Krzysztofowicz, K.
Powiązania:
https://bibliotekanauki.pl/articles/353220.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stainless steel
X-ray analysis
microhardness
sol-gel ceramic coating
Opis:
Crystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel substrates and stainless steel substrates coated with ceramic layer of barium strontium titanate were studied with microhardness tester. For measurements performed according to the Vickers method the average microhardness was found HV = 189 or HV = 186 for the “in-line” and “mapping” measurement pattern, respectively. The sol-gel method was used to coat the surface of the stainless steel substrate with a thin ceramic layer of the chemical composition Ba0.6 Sr0.4 TiO3 . It was found that the stainless steel substrate covered with sol-gel deposited ceramic coating exhibited the average hardness within the range HV = 217 up to HV = 235 for loading force F = 98 mN and F = 0.98 N, respectively. The Knopp method was also used and it was found that the stainless steel substrate with Ba0.6 Sr0.4 TiO3 coating exhibited hardness HK = 386.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 2; 911-916
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Corrosion Properties of Ca65-xMg17.5Zn17.5+x (x = 0, 2.5, 5) Alloys
Autorzy:
Babilas, R.
Wojciechowski, P.
Bajorek, A.
Sakiewicz, P.
Cesarz-Andraczke, K.
Powiązania:
https://bibliotekanauki.pl/articles/352466.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ca-based alloys
corrosion
hydrogen evolution
X-ray photoelectron spectroscopy
Opis:
The aim of the paper is to study the effect of zinc addition on the corrosion behavior of Ca65-xMg17.5Zn17.5+x(x = 0, 2.5, 5 at.%) alloys in simulated physiological fluids at 37°C. The electrochemical measurements allowed to determine a corrosion potential, which showed a positive shift from –1.60 V for Ca65Mg17.5Zn17.5 alloy to –1.58 V for Ca60Mg17.5Zn22.5 alloy, adequately. The more significant decrease of hydrogen evolution was noticed for Ca60Mg17.5Zn22.5 alloy (22.4 ml/cm2) than for Ca62.5Mg17.5Zn20 and Ca65Mg17.5Zn17.5 samples (29.9 ml/cm2 and 46.4 ml/cm2), consequently. The corrosion products after immersion tests in Ringer’s solution during 1 h were identified by X-ray diffraction and X-ray photoelectron spectroscopy as calcium, magnesium oxides, carbonates, hydroxides and calcium hydrate.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 3; 1033-1040
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies