Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Diesel engine" wg kryterium: Temat


Tytuł:
Analysis of application of chosen methods for tdc determination in marine diesel engines
Autorzy:
Łutowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/245396.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
transport
marine diesel engine
indication
TDC
Opis:
In the operating marine diesel engines the indication diagnostics tests are usually performed through a 0.5-1.0 me ter long indication channel which delays and disfigures the pressure signal being measured. the delay depends on the engine 's speed and load. the pressure sensor itself together with an amplifler is an additional source of delay and disfigurements, so the registered pressure curve is displaced even if theTDC piston's position hadbeen estimated with the highest accuracy. when the over exploited engine is being tested the angle of delay can achieve several degrees and differ for each cylinder. in that case cylinders' load is unequal and torsional vibrations occur in the engine operation. in case when some simplifying assumptions have been adopted the part of diagnostic information is lost what could lead to a false diagnosis. in the paper the attention is focused on the mistakes which could be made in the marine diesel engine diagnostics when different TDC assessment methods are used. TDC corrections with compression pressure analysis are possible only in case when crankshaft angle position is precise. in case of measurement with constant frequency such corrections are possible only when the engine is good balanced.
Źródło:
Journal of KONES; 2009, 16, 4; 301-306
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact analysis of internal catalyst converter on operating parameters of VW 1.9 TDI engine
Autorzy:
Haller, P.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/242517.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
catalyst
diesel engine
emissions
Opis:
The largest amount of air pollutants is produced by the combustion of fossil fuels (coal, lignite, petroleum, natural gas, etc.). Such combustion releases huge amounts of greenhouse gases into the atmosphere (including carbon oxides (CO, CO2), sulphur oxides (SO2, SO3), nitrogen oxides (NO, NOx)) and dust, ashes and soot. Transportation is a significant share of the air pollution, mainly wheel-based transportation. The combustion process in diesel engine is very complex physico-chemically and varies in time. The process is accompanied by simultaneous exchange of heat and mass and chemical reactions. The development of internal combustion engines is made towards meeting of the increasingly stringent requirements for toxic exhaust emissions, reduction of fuel consumption, and preservation of Earth's natural resources. The problem to solve in modern diesel engines is the emission of toxic compounds. One way to reduce emissions is to use a catalytic converter positioned directly in the combustion chamber of an internal combustion engine. The aim of this analysis is assessment of toxic emissions of a diesel engine with an internal catalyst. Qualitative assessment of engine emissions was determined by comparing test results of an engine with ceramic-ally coated valves against one with just conventional valves (commercial valves - without a ceramic coating). The study utilized a fourcylinder 1.9 TDI VW engine. It was expected that the use of glow plugs with an active coating would reduce the release of toxic compounds.
Źródło:
Journal of KONES; 2014, 21, 1; 99-106
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermal loads of engines for different properties of commercial fuels
Autorzy:
Sroka, Z. J.
Reksa, M.
Miksiewicz, K.
Powiązania:
https://bibliotekanauki.pl/articles/243852.pdf
Data publikacji:
2008
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
thermal loads
fuels
Opis:
It is oblivious, various properties of fuels cause different thermal loads of engines. Question is, how big is this effect and what fuel compound and its property play insignificant part. This paper is focused on problem of quality of diesel commercial fuels in Polish market and it is a challenge to find answer for question mentioned above. The academic staff from Wroclaw University of Technology organized tests with different commercial fuels. Chemical and physical properties of these fuels were studied and used for investigation to define relationships between them and thermal load during simulation process. All researches were done in the lab of Division of Motor Vehicles and Internal Combustion Engines at the Wroclaw University of Technology. Tests have showed differences in chemical and physical properties of fuels, but there is no statistics effect on engine parameters. Results have not also pointed any important differences in thermal loads of engine VW1,9 TDI and its components according to different physical and chemical properties of tested fuels. It is probably because there are differences of calorific values from one side but from other hands various density and specific fuel consumption compensated these differences. To burn unit of fuel contains higher level of oxygen, engine needs lower amount of air, so it gives, for the same fuelling system, lean mixture. It causes higher temperature of exhaust gases and a bit higher exhaust losses
Źródło:
Journal of KONES; 2008, 15, 2; 463-467
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wear profile of the cylinder liner in a motor truck diesel engine
Autorzy:
Koszałka, G.
Niewczas, A.
Powiązania:
https://bibliotekanauki.pl/articles/244295.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
wear
cylinder liner
Opis:
The paper presents results of investigation of cylinder liners wear. The investigation was carried out on diesel engines during long lasting operation in 5 motor trucks. Cylinder diameters were measured in two perpendicular planes on four depths using 2-point bore gauge, after removal of the cylinder head. Measurements were made every 50 000 km of vehicle mileage. Such methodology of measurements enabled to determine time course and wear profile of the cylinder liners (wear value in relation to the direction and height of the liner). It was stated that increments of diameter during the first period of operation are several times higher than during the later periods, when the wear intensity is constant. It was also found that wear of the cylinder liner in the plane perpendicular to the engine axis is bigger than in the parallel plane, and that wear in the upper part of the liner is twice as big as in its middle part. Measurement scheme for the cylinder liner; histogram of cylinder liner diameters obtained in measurements after the technological running-in of the engine after mileage of 0, 50,000 km, 150,000 km and 250,000 km, wear profiles of cylinder liners in the two directions at different vehicle mileages are presented in the paper. Estimated profiles of the cylinder liner wear will be used as input data for the calculations of the blowby intensity with the use of mathematical model of PRC set.
Źródło:
Journal of KONES; 2007, 14, 4; 183-190
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Correlation between cylinder pressure and noise emissions from diesel engines
Autorzy:
Narayan, S.
Powiązania:
https://bibliotekanauki.pl/articles/248079.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine noise
acoustics
vibrations
Opis:
The aim of this paper is to study the results obtained from a common rail dual cylinder diesel engine. Modern methodology involves the use of non-intrusive techniques of cylinder pressure measurements using sensors installed in the engine test rig. This work analysis the experiments carried out on a dual cylinder diesel engine .The results obtained are analysed to develop the relationship between the cylinder pressure levels and noise emitted from engine. Multiple injection process in diesel engines; engine test rig setup; cylinder pressure levels, noise levels; PSD plots for cylinder pressure signals, PSD plots for cylinder noise signal, PSD plots for cylinder pressure derivative signals for 1600, 2000 RPM; in cylinder pressure spectrogram at 1600 RPM, 100% load; motored cylinder pressure spectrogram at 1600 RPM; cylinder pressure and noise emission spectrograms; piston slap noise emissions, valve noise emissions and valve noise emissions spectrograms; and correlation between cylinder pressure and radiated noise levels are presented in the paper.
Źródło:
Journal of KONES; 2015, 22, 1; 243-254
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A comparative assessment of operating characteristics of a diesel engine using 20% proportion of different biodiesel diesel blend
Autorzy:
Ramalingam, Senthil
Rajendran, Silambarasan
Ganesan, Pranesh
Powiązania:
https://bibliotekanauki.pl/articles/243735.pdf
Data publikacji:
2019
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
biodiesel diesel blend
performance
emission
diesel engine
Opis:
The objective of the present work is to find out the viable substitute fuel for diesel and control of pollutants from compression ignition engines. Therefore, in this present investigation an attempt has been made to study the effect of 20% proportion of five different biodiesel diesel blend in diesel engine. The 20% proportion of biodiesel such as Jatropha, Pongamia, Mahua, Annona and Nerium and 80% of diesel and it is denoted as J20, P20, M20, A20 and N20 are used in the present investigation. The experimental results showed that the brake thermal efficiency of the different biodiesel blend is slightly lower when compared to neat diesel fuel. However, N20 blend, have shown improvement in performance and reduction in exhaust emissions than that of other biodiesel diesel blends. From, the experimental work, it is found that biodiesel can be used up to 20% and 80% of diesel engine without any major modification. The conducted experiments were conducted on a four cylinder four stroke DI and turbo charged diesel engine using biodiesel blends of waste oil, rapeseed oil, and corn oil with normal diesel. The peak cylinder pressure of the engine running with bio diesel was slightly higher than that of diesel. The experiments were conducted on a four cylinder four stroke diesel engine using bio diesel made from corn oil.
Źródło:
Journal of KONES; 2019, 26, 1; 127-140
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
An effect of physical and chemical properties of commercial diesel fuels on engine parameters
Autorzy:
Sroka, Z. J.
Reksa, M.
Kułażyński, M.
Powiązania:
https://bibliotekanauki.pl/articles/242752.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
engine fuels engine performances
Opis:
This paper is focused on problem of quality of diesel commercial fuels in Polish market and an effect of their properties as well on engine parameters as environment The academic staff from Wrocław University of Technology put the own experience to the huge discussion by making research in the Wroclaw-city, where some probes of fuels were taken from six different commercial fuel stations. Chemical and physical properties of fuels were checked. A real diesel engine VW 1,9 TDI was investigated in university lab of Division of Motor Vehicles and Internal Combustion Engines. Typical engine performances were built including power, torque, fuel consumption, toxicity levels due to different fuels. The IC engine on the test bench, oxygen content in fuels, example of full load performance of VW1,9 TDI for fuel Bio D20-type, differences of mean effective pressure for different fuels, differences of carbon monoxide in exhaust for different fuels, differences of nitric oxides in exhaust for different fuels, differences of smog level in exhaust for different fuels, differences of heat release for different fuels, relation between engine torque and oxygen content in fuels vs. engine rotation are presented in the paper.
Źródło:
Journal of KONES; 2007, 14, 4; 447-452
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A fatigue testing method of wet cylinder liner of diesel engines
Autorzy:
Kaźmierczak, A.
Kolanek, Cz.
Powiązania:
https://bibliotekanauki.pl/articles/247871.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
cylinder liner
fatigue
Opis:
It has been agreed to call the loads changing with time and acting in most varied constructional arrangements as well as the stresses accompanying them changeable or cyclic. Changeable stresses produce in the material a very complex entanglement of phenomena and changes depending on the value of those stresses and on the number of cycles. These are fatigue phenomena and changes. They develop successively till the element has been destroyed. This is called the element material fatigue. Thus changing loads and stresses are also called fatigue loads and stresses. The purpose of the presented work was to develop a method of comparative investigations for wet replaceable sleeves in direct contact with coolant that have been submitted to technological treatment of sub-edge zone material strengthening. The source of loads is a cyclically occurring normal component of gas and mass forces in the cylinder. The frequency of changes is a derivative of the number of strokes in the engine run and of the rotational speed of the crankshaft. Fatigue loads can be the reason why cylinder liner cracks in the edge zone. The results of the fatigue testing of the technological process of strengthening the cylinder lines sub-edge zone on crack sensitivity shows differences in the behaviour of particular samples, depending on the parameters of strengthening. The fatigue testing method can be used to evaluate the technological process of cylinder liner.
Źródło:
Journal of KONES; 2007, 14, 3; 287-290
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Vibro-acoustic methods in marine diesel engines diagnostics
Autorzy:
Lus, T.
Powiązania:
https://bibliotekanauki.pl/articles/245521.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
turbocharger
diagnostics
vibration
Opis:
Vibro-acoustic diagnostic methods which are used on marine high-speed diesel engines with turbochargers are presented in this paper. Vibration and acoustic signals generated by turbochargers need different signal processing methods to be effective and faultless in turbochargers diagnostics. Diagnostic methods which based on vibration and acoustic signals analysis are sensitive on engine load and speed changes. Methods presented in this paper based on vibration and acoustic signals processing in time and frequency domain. Using this methods checking technical condition of the turbochargers and its rotors and bearings without stopping the engine and dismantling it is possible. Examples of radial-flow rotor turbine overgrown by carbon soot and axial-flow rotor turbine without turbine blades, sound intensity level of turbocharger and acoustic spectrum of turbocharger in octave mode acoustic spectrum of turbocharger in octave mode for two different technical conditions, acoustic and vibration signal spectrum of the turbocharger, vibration acceleration amplitude of first harmonic for three turbochargers, values of harmonic vibrations of accelerations equivalent of turbine blades number, amplitude of vibrations accelerations in frequency domain for turbocharger in good and bad technical conditions are presented in the paper.
Źródło:
Journal of KONES; 2011, 18, 3; 203-210
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Engine fuel characterisation through ultraviolet absorption spectra
Autorzy:
Baszanowska, E.
Otremba, Z.
Powiązania:
https://bibliotekanauki.pl/articles/245537.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
fuel
spectroscopy
absorptivity
diesel engine system
Opis:
In the article, light absorption properties of the fuel oil are considered with a view to create basis for establish optical indicator of the type and quality of this kind of crude oil derivative, in this case the Diesel fuel. The organic solvent – n-hexane – was chosen as a solvent to prepare samples of dilutions of Diesel fuel in several oil concentration. Spectrophotometer Aqualog Horiba were applied to record the absorbance spectra in the ultraviolet and visual range of the light (from 240 to 600 nm) for each previously prepared samples. Obtained results allow concluding that the changes of absorbance occur primarily in the wavelength range from 240 nm to 355 nm. Moreover, the absorbance spectra are characterized by the characteristic sharp peak located at 270 nm for excitation wavelength. Spectra of absorbance were converted to spectra of absorption coefficient based on Lambert-Beer law. Due to the independence the absorption coefficient from the fuel concentration, this parameter could be used as a potential indicator to access composition and quality Diesel fuel used in the diesel engine system. Therefore, preliminary tests allow concluding that absorption coefficient for selected wavelength located at 270 nm could be a sensitive indicator for quick access to fuel quality.
Źródło:
Journal of KONES; 2017, 24, 3; 15-19
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Marine diesel engine valve gear mechanism diagnostics problems
Autorzy:
Lus, T.
Powiązania:
https://bibliotekanauki.pl/articles/245681.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
diagnostics
valve gear
Opis:
Marine diesel engines have changed their construction last years because of electronic control implementation in fuelling process. Electronic control implementation could be also important in valve gear mechanism which is main part of the engine gas es exchange system. In this paper problems connected with of valve gear mechanisms operation and diagnostics have been presented. the diagnostic methods and processes which could impact diagnostic process will be shown together with examples from test bed and real vessels. diagnostic methods which based on vibration signals analysis are sensitive on engine load and speed change. separate engine cylinder 's loads generale differences in so called "dynamic valve gear diagrams " which will be shown for some marine engine types. opening and closing of inlet and exhaust valves generale vibration signals in entire engine structure. There are some tools available in signal analysis which gives opportunity to trace changes in signal patterns in real time monitoring systems. special diagnostic method based on vibration signal analysis worked out in the polish naval academy, gives opportunity to change engine maintenance philosophy from scheduled planed maintenance system to condition based maintenance system without fear about real operating engine conditions.
Źródło:
Journal of KONES; 2009, 16, 4; 287-292
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Procedures and treatments leading to reduction of toxic components emission in diesel engines exhaust gas
Autorzy:
Kalina, P.
Irzycki, A.
Snopkiewicz, K.
Powiązania:
https://bibliotekanauki.pl/articles/248119.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
pollution
reduction of emission
Opis:
The fight against global warming and Earth atmosphere pollution has been for years one of the most important tasks of governments and national economies of the European Union members. Abandonment of efforts leading to reduction mainly of carbon dioxide emission by heavy industry, electric power generation based on coal, passenger aviation and wheeled passenger transport will inevitably be leading to deterioration of health condition of our citizens. This article presents an overview of commonly used structural and technological treatments which have impact on reduction of toxic standardized exhaust pollutants in the surface transport, exemplified on SW 400 engine version of L2 / 3 and its turbocharged version 6CT 107 2/L2. The impact of: engine's adjustment parameters, catalytic afterburners, exhaust gas recirculation, modifications of injectors, turbochargers, supercharging air-cooling and particulates filter on carbon monoxide, hydrocarbons, nitrogen oxides and particulates emission was thoroughly examined. The parameters being compared were the results of toxicity tests according to ECE-R49 Regulation and a maximal smoke values on full-load characteristics. In conclusion, of the paper the limiting allowable values of toxic components emitted in Diesel engines exhaust gases in the following EU Emission Standards are presented.
Źródło:
Journal of KONES; 2012, 19, 1; 163-169
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of diesel fuel mixture and camelina oil ester on selected parameters of combustion process
Autorzy:
Orliński, P.
Powiązania:
https://bibliotekanauki.pl/articles/243639.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
camelina oil ester
combustion
diesel engine
Opis:
This paper presents the results of comparative research into basic physical and chemical properties of pure diesel fuel and two types of mixtures: Camelina oil ester (Camelina oil ester content in the mixture was 10% and 15%) and diesel fuel. Camelina oil ester was used to show that it can also be used as an additive plant to diesel fuel (according to the plans of the European Union). Similarly to on a large scale used ester of rapeseed oil. The base fuel in the research was clean diesel fuel (without the addition of ester as in the case of diesel fuel available at petrol stations).The use of fuels with different physical and chemical properties to supply the diesel engine and the use of measuring equipment used for determining the parameters of fast-changing operation resulted in the determination of the operating medium average pressure during the combustion process. On the basis of the experimental pressure characteristics of heat release were identified. Analysis of these characteristics determined the proportion of total combustion phases of kinetics and diffusion, depending on the type of fuel and operating conditions. Finally, the paper shows that the fuel with different physicochemical properties has a significant effect on the combustion process. A comparative assessment of the suitability of tested mixtures for operational use was made.
Źródło:
Journal of KONES; 2013, 20, 3; 291-298
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Residual stresses assessment in the marine diesel engine crankshaft 12V38 type
Autorzy:
Król, K.
Wikło, M.
Olejarczyk, K.
Kołodziejczyk, K.
Siemiątkowski, Z.
Żurowski, W.
Rucki, M.
Powiązania:
https://bibliotekanauki.pl/articles/244853.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
crankshaft
simulation
residual stress
Opis:
In the paper, the measurement of the marine diesel engine crankshaft residual stresses is presented. The hole drilling strain gauge was chosen because of its simplicity and low cost. Moreover, deflection calculation was made for the load corresponding to its weight and the concentrated force in the chosen bearing conditions. Deflection of the journal and bending rigidity under the concentrated force was calculated as well. In that case, the crankshaft was supported in the neighbouring crank journals. The reduced stresses were calculated according to the Huber – Mises hypothesis. The residual stresses were measured in the marine diesel engine crankshaft type 12V38 after the finishing, with the hole-drilling method. It was found that the residual stresses reach the maximal value of 86 MPa, but for 50% of measuring points, the residual stresses did not exceed the value of 20 MPa. The squeezing stresses were found to be dominant. The measurement results provided important data for further consideration, especially for the correction of the bending deformation of the produced crankshaft.
Źródło:
Journal of KONES; 2017, 24, 2; 117-123
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact analysis of air humidity on operating parameters of diesel engine
Autorzy:
Haller, P.
Jankowski, A.
Kolanek, C.
Magdziak-Tokłowicz, M.
Wróbel, R.
Powiązania:
https://bibliotekanauki.pl/articles/246293.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
humidity
diesel engine
efficiency
engine power
engine torque
Opis:
A major problem in the combustion diesel engines is the different distribution of the mixture of air and fuel and also temperatures inside the combustion chamber. It helps the formation of points of the high and low oxygen concentration in the combustion chamber of the engine. In areas with a high concentration of oxygen, the combustion process produces very harmful NOx, and in places with low oxygen concentration, as a result of incomplete fuel combustion particles are created in the form of soot. This not regular distribution of the mixture of air and fuel and temperatures in the combustion chamber affect the limited maximum engine power and efficiency at his every operating cycle. One method for improving the combustion process is feeding into the engine air with high relative humidity. The study was conducted on a chassis dynamometer at the Department of Vehicles Engineering Wroclaw University of Technology. For the purposes of the study determined the external characteristics, including maximum engine power and maximum engine torque at different air relative humidity and quite similar air temperature. Analysis of the results of research shows that high air relative humidity has a positive effect on the work parameters of the diesel engine.
Źródło:
Journal of KONES; 2015, 22, 3; 37-42
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of the shape of the combustion chamber on exhaust gases toxicity in T370 engine
Autorzy:
Kalina, P.
Kawalec, M.
Powiązania:
https://bibliotekanauki.pl/articles/243782.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
combustion chamber
geometry
toxicity
Opis:
An important issue in construction of combustion chamber in compression-ignition engines is proper selection of its shape and size. Both features are dependent on several factors such as fuel injector location and angle, spray atomizer selection (amount of holes, their diameter and angular position), location of inlet valve and air turbulence. By doing research on prototype engine T370, an analysis of influence of combustion chamber size and its modifications going towards lip construction on flue gas toxicity was done. The diameter and depth of combustion chamber was being changed while maintaining the same compression ratio. After that, a modification of tested combustion chambers was made by creating so called “lip”, which aim was to create a swirl of injected fuel in the vertical plane. To visualize the changes in swirl, a numerical analysis of fuel injection into combustion chamber was made. In discussed study, emission tests were performed according to ECE-R49. During the research six combustion chambers with diameters 60, 63 and 66 mm (and their modification) were investigated. Tests were performed for several types of injectors and different injection timing. However, for analysis of combustion chamber size the results are presented for the same injectors but with optimized injection timing.
Źródło:
Journal of KONES; 2015, 22, 2; 104-108
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comperative analysis of emision from engine fuelled with diesel and bio-diesel
Autorzy:
Koszałka, G.
Hunicz, J.
Kordos, P.
Powiązania:
https://bibliotekanauki.pl/articles/242081.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
alternative fuel
bio-diesel
exhaust emissions
Opis:
The paper presents comparative analysis of operational parameters, smoke emission and toxic components contents in exhaust gases of a compression ignition engine fuelled with fossil diesel, commercial bio-diesel (fatty acid methyl ester) and their blend. Measurements were conducted on an older generation diesel engine equipped with in-line injection pump. Engine was operated in conditions of full load rotational speed characteristic and also ESC steady-state test cycle. Fourier Transform Infrared (FTIR) analytical system provided contents of 23 exhaust gas components. In particular chosen parameters of investigated fuels (on the base of quality reports), performance and fuel consumption characteristic versus rotational speed, smoke emission (D) and content of carbon monoxide (CO), unburned hydrocarbons (THC) and nitrogen oxides (NOx), sulphur dioxide (S02) and carbon dioxide (CO2) in exhaust gas of the engine fuelled with investigated fuels, emission of specific hydrocarbons of the engine fuelled with investigated fuels, of non-regulated compounds measured during the research, molar mass of analyzed exhaust compounds are presented in the paper.
Źródło:
Journal of KONES; 2009, 16, 3; 165-171
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Dual - fuel low power generator with diesel engine using alternative fuels
Autorzy:
Imiołek, M.
Piętak, A.
Imiołek, A.
Powiązania:
https://bibliotekanauki.pl/articles/246549.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
alternative fuels
diesel engine
dual-fuel engine
biofuels
Opis:
At the moment, there is a growing interest in low-power generating units in dispersed system. The production of energy in small units located in the vicinity of the energy recipients offers considerable benefits. First and foremost, it lowers the cost of energy production and the cost of its transfer and also makes the recipient independent from the domestic supplier. Small cogeneration aggregates will facilitate the use of energy from dispersed renewable resources. Gas self-ignition engines in cogeneration system powered with biofuels can be used in construction industry as ecological sources of heat and electrical energy, limiting the need for fossil fuels. This paper presents the possibility of using alternative fuels for internal combustion engines. It describes the possibility of using liquid biofuels separately or natural gas fuel to power diesel engines in dual fuel system. The conception of supplying low-power generator with diesel engine with natural gas to a dose of liquid biofuels test case. Pointed to the factors determining the desirability of a particular concept. Indicated the modification of the engine power to supply the natural gas generator with a dose of liquid biofuels. New technologies of extracting and using biofuels and alternative fuels are being introduced and developed for generating heat and electric energy. Studies on the use of gas and liquid alternative fuels are directly linked to research on the production of renewable and alternative energy as well as environment protection by minimizing emissions of toxic substances into the atmosphere.
Źródło:
Journal of KONES; 2012, 19, 3; 171-176
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A comparison of selected operating parameters of the diesel engine fuelled with mixtures of diesel oil or liquid bio - fuel and natural gas for low - power generators
Autorzy:
Boruta, G.
Imiołek, M.
Powiązania:
https://bibliotekanauki.pl/articles/241789.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
dual-fuel engine
biofuels
alternative fuels
Opis:
Following the modern fuel market, one can notice that prices of liquid petroleum derivatives - petrol and diesel oil - which most often fuel piston internal combustion engines are increasingly higher. Similarly, the price of petroleum-derivative gas (LPG - the liquefied petroleum gas - simply speaking, a mixture of propane and butane) is also growing. Many academic and industrial institutions of science conduct research to determine whether it is possible to replace liquid petroleum-derivative fuels with some other potentially cheaper ones. It would also be beneficial if these new fuels were more "ecological" - so that their combustion products would not be harmful for the environment and if they were produced with the use of plants. Fuel stations commonly offer a fuel for diesel engines which is a mixture of fatty acids methyl esters (FAMEs) from vegetable oils, in Poland for instance from rape seeds. The paper presents a comparison of selected operating parameters of the Hatz 1B40 engine fuelled with mixtures of diesel oil or liquid bio-fuel and natural gas. Indicator diagrams, exhaust gases composition and vibration signals recorded on the engine body were analyzed. The study was conducted on the Hatz 1B40 diesel engine which is used among others in FOGO power generator sets, after replacing the original feeding system by common rail system for liquid fuels and after adding natural gas feeding system.
Źródło:
Journal of KONES; 2012, 19, 4; 111-116
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Water - fuel microemulsions influence on fuel consumption and exhaust gas emissions
Autorzy:
Cienciała, M.
Haller, P.
Jankowski, A.
Kardasz, P.
Powiązania:
https://bibliotekanauki.pl/articles/244361.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
microemulsion
fuel consumption
emissions
Opis:
Combustion in a diesel engine is a complex physicochemical process, changing the time at which the events take place simultaneously heat and mass transfer and chemical reactions. The development of internal combustion engines goes towards meeting the increasingly stringent requirements for toxic exhaust emissions, reducing fuel consumption and therefore reduce carbon emissions and protect the Earth's natural resources. The problem to solve in modern combustion engines is the emission of NOx. One way to reduce the emission of toxic NOx combustion engine power is water-hydrocarbon emulsions [1]. Research combustion engines water-hydrocarbon emulsions has been its tradition. So far, attempts were carried out using an emulsion obtained by a chemical. Emulsions of oil and water can be obtained by adding various detergents to prevent delamination of the oil and water. In this article, we consider the possibility of applying a mixture of water and oil as an alternative fuel used to power internal combustion engines used in heavy road transport. This work is preliminary work, also having to check whether this is the future direction of the work. The measurements of emissions of exhaust gases and fuel consumption. After analysing the test results confirmed that the improvement of the economic and environmental performance of modern diesel engines, it can be achieved by supplying synthetic diesel or gas oil water emulsions. It was found that the use of emulsion leads to a reduction of fuel consumption and NOx emissions.
Źródło:
Journal of KONES; 2013, 20, 3; 111-116
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Energy - time method for assessment of main diesel engine operation
Autorzy:
Rudnicki, J.
Powiązania:
https://bibliotekanauki.pl/articles/246378.pdf
Data publikacji:
2007
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
ship power plants
diesel engine performance
reliability
Opis:
This paper presents a development of the known qualitative method for assessment of engine operation, applied to ship main diesel engine as an example. According to this interpretation engine operation can be presented as a physical quantity. In this aspect, based on the selected functional system of the engine, was assessed usefulness of the quantity for description reliability features of the system. To the analysis was applied Poisson's uniform process which made it possible to elaborate a model of run of worsening the considered system's operation taken as a random process of identical independent decreases of energy efficiency within a given time interval. The presented method is a valuable supplement for description reliability features of ship main engine what is important for realization of shipping tasks by sea. Additional advantage is versatility which makes that it can be applied to reliability analysis of any ship device or ship energy subsystem. Classification of the engine serviceability states with taking into account the assessment of its operation in energy-time aspect, schematic diagram of lubricating system of RTA48-TB engine and values of lubricating oil parameters in steady conditions for the engine load, graphical presentation of lubricating oil cooler operation graphical interpretation of the decreasing of oil cooler efficiency are presented in the paper
Źródło:
Journal of KONES; 2007, 14, 3; 519-526
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The analysis of the energy balance of the engine powered by diesel oil mixture with butanol
Autorzy:
Sitnik, L. J.
Andrych-Zalewska, M.
Powiązania:
https://bibliotekanauki.pl/articles/247462.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diesel engine
fuels
dense alcohols
energy balance
Opis:
The development of motorisation involves using bigger amounts of fuels. These fuels are, until now, mainly petroleum. However, the fuels of bio origin must be used as well. It follows from the necessity of ensuring CO2 balance and from the fact that oil sources sooner or later will become exploited. Not less important is the fact that, principally, it is difficult to change the proportions of petrol and diesel oil extracted from crude oil, and the use of diesel oil increases proportionally faster than petrol. Therefore, it is necessary to use bio additives in diesel oil. One of such additives is dense alcohols. The aim of the present work is to determine the energy balance of diesel engine powered by diesel oil and butanol mixture. The work field includes making of energy balance of the engine in its characteristic points responsive 13 phase ESC test as well as determining on this basis the consolidated values concerning the differences in the engine energy balance. It has been proved, that powering the engine by mineral diesel oil with doped butanol (20% v/v) does not lead to essential differences in the energy balance of the engine- which does not mean, that the essential differences are absent in the particular characteristic points of the engine. It requires more detailed explanation (in the further research works) because losses in the combustion process do not show differences, but in the other balance components the differences are shown.
Źródło:
Journal of KONES; 2015, 22, 4; 269-273
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Asymmetry increase in the course of compression pressure as a measure of obstruction in indicating channel
Autorzy:
Łutowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/242408.pdf
Data publikacji:
2016
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
indicated
indicated channel
diagnostics
Opis:
Indicating process of large combustion engines for both marine and industrial applications is performed using the indicating channels with valves. The impact of these channels on the values of parameters obtained from engine’s indication is significant. In previous studies, it had been shown that during exploitation accidental degradation of the indicating channels occurs. Carbon deposits, which appear in the channels, are limiting their patency. Leaks in channels connections are also appeared. Disregarded state of degradation of indicating channels will change the image of indicated pressure course, different for each cylinder of the engine. When cylinders are indicated using commercial instruments, the status of the channel is not in any way taken into account. At one gas compressing station in Poland, which has compressor diagnostic system, developed by the author, with stationary indicator, inverted IIR filter has been used. This filter is used to adjust the recorded waveforms of indicated pressure on motor-compressors GMVH type, and the filter coefficient is chosen to offset the associated throttling signal delay. Information about the delay of the signal is missing, however, in the case of popular portable indicators that do not use tags from crankshaft position. The paper presents a method for assessing the state of the indicating channel, based on the asymmetry measurement of compression course obtained after cut-off the fuel supply to the tested cylinder. The study model shows that leakage from the combustion chamber, interference in cooling and other defects cause only slight and predictable disruption of symmetry. The analysis of compression pressure course (without fuel delivery) immediately prior to each cylinder indication, in the case of positive verification, increases the reliability of diagnosis. In the case of negative verification, measure of the asymmetry could be the basis for the adjustment of acquired pressure waveforms and achieved from them parameters.
Źródło:
Journal of KONES; 2016, 23, 3; 311-316
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Reverse IIR filter as a tool for cylinder indicating channel patency impact correction on measured cylinder pressure waveform
Autorzy:
Łutowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/242647.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
indicated
diagnostics
indicated channel
Opis:
Indicating of large marine and industrial diesel engines is made with using indicating channels in cylinder head with valves. The impact of these channels on the value of the parameters obtained from indicating is significant. However, indicating is commonly used for comparative tests assuming that this error is the same on all cylinders of the same engine in identical conditions. As a result of operation especially in cylinders with irregular combustion process the coke occurs in the channel limits its patency. It causes changes in the image of indicated pressure. In such a situation defined parameters are subject of considerable random error. In the earlier studies on the engine Sulzer type 6AL20/24 cylinder channel failure was simulated and channel chocking symptom was observed as apparent TDC shift relative to a reference mark connected with the shaft. As part of ongoing studies attempt to reconstruct distorted pressure curve by chocked indicating channel was made. It is assumed that the channel with the valve is only connection between throttling element in the form of a channel with the much greater volume of the valve. Such a structure was modeled as IIR filter. For this type of filter, there is an unequivocal inverse transformation, which, at least in theory gives possibility to reconstruct the distorted pressure waveform. The reconstruction was carried out by selection of the filter coefficients so as to eliminate the shift of TDC. In practice it turned out that the reconstruction is not perfect. All obtained pressure waveforms are slightly noisy and distorted in the first phase of expansion. Despite this, there was a significant reduction in errors of some parameters determined from the reconstructed pressure waveform.
Źródło:
Journal of KONES; 2013, 20, 2; 253-259
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Decomposition of harmonic wavelets of torsional vibrations as basis for evaluation of combustion in compression-ignition engines
Autorzy:
Dereszewski, M.
Drewing, S.
Powiązania:
https://bibliotekanauki.pl/articles/243609.pdf
Data publikacji:
2018
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diagnostics
diesel engine
torsional vibrations
signal processing
Opis:
The aim of analysis presented in the article is results of measurements of torsional deflections of a crankshaft of three-cylinder internal combustion diesel engine. The wavelets of the run of torsional twists were processed by decomposition to harmonics using FFT. In order to exactly recognize all dynamic aspects of gas forces acting during working stroke, decomposition was done in two ways: first one relaying on records encompassing one working cycle (two revolutions), the second one based at separated periods encompassing angular an interval from TDC (Top Dead Centre) of one cylinder to TDC of subsequent in firing order. For three-cylinder engine, width of the interval is 240 degrees of crank angle. In order to obtain reliable results, torsional deflection signals acquisitions were recorded numerous times including changes of outer conditions (temperature, atmospheric pressure) and different values of the engine loads. The main goal of conducted experiments was looking for an answer of a question if exist any differences between frequency spectrums of harmonics of run of full cycle ( two revolutions) and the same cycle divided by three separate intervals. Analysis was conducted in order to state any possibility of diagnostic signals acquisition caused by abnormalities of combustion process. Results were presented in form of comparison of frequency spectra taken from full cycle and divided intervals.
Źródło:
Journal of KONES; 2018, 25, 3; 129-135
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The possibility of use a waste product of biofuels production-glycerol as a fuel to the compression ignition engine
Autorzy:
Grab-Rogaliński, K.
Szwaja, S.
Powiązania:
https://bibliotekanauki.pl/articles/243807.pdf
Data publikacji:
2016
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
glycerol
alternative fuel
diesel engine
combustion properties
Opis:
The article presents results of tests performed in a combustion research unit (CRU) with the two following fuels: light fuel oil (LFO) and glycerol. The CRU is a constant volume combustion chamber machine equipped with an injection system based on that used in common-rail diesel engines with electromagnetic injectors. This machine allows to compare various combustion properties between fuels for specified parameters of injection and a combustion chamber as well. As it is known glycerol is a substance which is obtained from several technological processes such as production of biofuel thus in this way it can be treated as an alternative renewable fuel. The glycerol is characterized by low heating value of 16MJ/kg and relatively high density of 1261 kg/m3. However, its heating value by volume is higher if compared to other liquid fuels. From that reason decrease in energy that can be delivered with fuel is smaller which is approximately 16% lest than for LFO. The parameters measured during this research were: pressure increase, rate of pressure increase (ROPR), ignition delay (ID), main reaction delay (MRD), main combustion period (MCP), end of main combustion (EMC), end of combustion (EC), position of max ROPR (PMR) and max ROPR. The tests were performed with different injection parameters such as injection pressure, injection duration and injection delay as well as under various conditions in the CRU combustion chamber expressed by pressure and temperature. On the basis of these tests the comparison between LFO and glycerol was done. The results were presented in diagrams. The research shows that glycerol used as a fuel, to obtain the same output power, should be injected at higher amounts. Glycerol as a fuel cannot ignite itself, hence to provide combustion the pilot injection of another fuel have to be applied.
Źródło:
Journal of KONES; 2016, 23, 3; 157-164
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Potential non-toxic aqueous emulsion as a diesel fuel
Autorzy:
Haller, P.
Jankowski, A.
Kolanek, C.
Walkowiak, W.
Powiązania:
https://bibliotekanauki.pl/articles/244342.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
emulsions
water
diesel engine
nitrogen oxides
emissions
Opis:
Natural processes occurring on Earth (fires, volcanic eruptions) and human activity in the area of acquisition and processing of energy, is the cause of the continuous contaminating the atmosphere of combustion products. The combustion of fuels is and will be in the near future primary means of generating energy, including for transportation purposes. Transport is the cause of many environmental threats - emits dust and particles along with many of gaseous harmful substances and also noise and vibration. Power sources used for transport are almost exclusively equipped with internal combustion engines, among which is dominated by a diesel engines. In view of the known advantages of these motors such as high efficiency and relatively low emissions of toxic compounds in the exhaust gas, they have been accepted as the most preferred source of power motor vehicles in the coming decades, assuming that meet the requirements of future regulations regarding environmental protection. The problem to be solved in internal combustion engines is the emission of nitrogen oxides. In this paper are contained an overview of proven methods and results in the reduction of nitrogen oxides in exhaust gases by means of emulsion fuels, and forming an opinion concerning of the usefulness of such solutions in the future.
Źródło:
Journal of KONES; 2015, 22, 3; 43-48
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of oil refilling strategy on the amount of oil in trunk piston marine diesel engine lubricating system
Autorzy:
Młynarczak, A.
Powiązania:
https://bibliotekanauki.pl/articles/246111.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
lube oil
refilling strategy
Opis:
The issues connected with the amount of lube oil in engine oil system are real problems in marine diesel engines maintenance process. The amount of lube oil in circulation influences its quality and consequently the wear of lubricated parts. That amount still changes and is connected with lubricating oil refilling strategy. The results of simulation carried out for SULZER 8S20U and PIELSTICK 12PC2-5V engines allowed to determine the influence of lubricating oil refilling strategy on the amount of lube oil in circulation. Frequent topping-up at regular intervals can be arranged to maintain the sump working capacity at the chosen percentage of the design maximum (for example 90 per cent), while a significantly delayed topping-up might allow the working capacity to be reduced to as low as about 50 per cent of the maximum. Thus a significantly reduced lubricant amount may have a disadvantageous influence on engine elements wear (i.e. piston rings, cylinder liners) and consequently cause the growth of the engine overhaul costs, although in far perspective, it would be difficult to connect that fact with the amount of oil in circulation. On the other hand in small output trunk piston engines without sump tanks, delayed topping-up and operation with minimum oil level could give some economic and ecological advantages resulting from reduced oil consumption. But in marine conditions (rolling and trim changes) it would be very hazardous for the engine safety operation.
Źródło:
Journal of KONES; 2011, 18, 3; 287-291
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The total NOx emission control possibility in modern large bore, slow speed marine engines
Autorzy:
Borkowski, T.
Powiązania:
https://bibliotekanauki.pl/articles/246219.pdf
Data publikacji:
2008
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
injection assembly
exhaust emission
Opis:
The common demands for environmental protection in shipping are being recognized by IMO, through development of the rules with respect to SOx and NOx. This paper investigates the results of fuel injection variables, affecting cylinder process performance and exhaust gas emission. The effect of injection assembly design attributed on NO emission was estimated. The similar slow speed, large bore MAN B&W engines performance were compared. The main factors used for evaluation were: fuel consumption, rotational speed, mean and maximum in-cylinder pressures and total concentrations of NOx, CO2, O2i CO, and HC. The engines performance and NO emission were compared with conventional 6S60MC-C and latest — electronically controlled 7S60ME-C. The CFD simulation of combustion and pollutant formation was created to represent processes of a marine large bore engine. The SMC-C engine operation and standard injection nozzle design was taken as a baseline for comparison with measured NO concentration. The predicted cylinder pressures showed reasonable agreement with experimental measurements. The predictive ability of used CFD simulation package was found to be quantitatively insufficient in terms of NOx emission. However, the predicted NO emission exhibits similar sensitivity with experiment results. The quantitative set of reference data for the validation of simulation results needs to be substantially improved. The determination offuel injection and cylinder pressure history can be identified as the most important source of inaccuracy. Finally, weighted NOx specific emission factor for both engines shows close value, sufficiently placed against IMO limit presented in Fig. 11. The results are promising and show that controlled combustion process is capable of fulfilling present and future NOx emission requirements. Modern marine engines are designed with adjustable components to allow the engine to be adjusted for maximum efficiency or NOx weighted emission factor when used in particular application.
Źródło:
Journal of KONES; 2008, 15, 2; 21-28
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Combustion characteristics for small diesel engine by using emulsified blend fuels of vegetable oil and light oil
Autorzy:
Kawakami, T.
Powiązania:
https://bibliotekanauki.pl/articles/247229.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion characteristics
small diesel engine
ecology energy
Opis:
The paper is focusing on combustion characteristics for small diesel engine by using emulsified blend fuels of vegetable oil and light oil. Target is to achieve low emissions and low fuel consumption for internal combustion engines. The fuels used in this study are light oil, blend fuels [light oil + coconut oil, light oil + palm oil], and emulsified fuels [light oil + water, blend fuels + water]. Mean increasing rate of pressure is calculated from the value which subtracted initial pressure from maximum burning pressure divided by total burning time. The mean increasing ratio of pressure is calculated from the value which subtracted initial pressure from maximum burning pressure divided by the total burning time. The emissions in exhaust gas are measured with an analyzer of exhaust gas. The data of 30 tests for each engine revolutions were averaged arithmetically. Experimental approach and results have been presented by details. The main conclusions are as follows: it is possible to control the combustion behaviour by using blend fuels and emulsified blend fuels for small diesel engine; the maximum burning pressure of emulsified blend fuels increases at low engine speed; the CO emission of blend fuels is smaller than that of light oil; the NOX emission of emulsified coconut blend fuel and emulsified palm blend fuel is smaller than that of light oil; the CO emission of emulsified Coconut-Palm blend fuel is equal to that of light oil at low engine speed.
Źródło:
Journal of KONES; 2011, 18, 4; 185-190
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Assessment of the diagnostic suitability of net thermal efficiency of marine diesel engine
Autorzy:
Pawletko, R.
Polanowski, S.
Witkowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/247360.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
indicator diagram
thermal efficiency
diesel engine diagnosis
Opis:
This article applies to searching for symptoms and diagnostic parameters pointing in a deterioration in the quality of the combustion process in marine diesel engines. It was assumed that diagnostic parameters should give clear information regardless of engine load or with respect to the mean indicated pressure. The proposed cycle and sectional net thermal (heat) efficiency characteristics and also dimensionless net heat release rate were analysed. In order to obtain the state of deterioration of the injection process simulation of discalibration (larger diameter) of injector holes was performed. The simulation was carried out by the enlarged of diameter of the injector holes form 0.375 mm to 0.385 mm. Deterioration of the formation and growth of fuel spray droplet diameter is result of such simulation. The study was conducted on a laboratory engine Sulzer Al25/30. The study was carried out according to active experiment plan, during which the selected engine failure of the injection system was simulated. Measurements of pressure of combustion were performed by means of tensometric sensors of Spice Company on the indicator valve. The analysis found that in the event of injector nozzle faults (discalibrated holes) significantly decreases the net thermal efficiency η c cycle, and there are significant oscillations of net
Źródło:
Journal of KONES; 2013, 20, 4; 327-332
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of diesel/ethanol blends on variations of selected combustion parameter
Autorzy:
Lotko, W.
Smigins, R.
Górski, K.
Powiązania:
https://bibliotekanauki.pl/articles/242253.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
misfire detection
diesel engine
combustion process
ethanol
Opis:
This paper presents and discusses selected research results of the diesel engine fuelled with blends of: diesel oil (DO), synthetic ethanol (ET) as oxygenated additive and small quantity of fatty acid methyl esters (FAME) used as emulsifier. Content of ethanol in diesel oil was changed in wide range (up to 50%). Addition of 5% by vol. Of FAME was constant for each tested mixture. Preliminary tests were focused on influence of fuels blends composition on its combustion process. The main analyzed parameter was mean indicated pressure and its unrepeatability index. Research suggests that diesel oil blended with up to 20% of ethanol can be successfully used for diesel engines feeding. Higher ethanol content in mixture with diesel oil is unfavourable because misfire phenomenon occurs immediately. In this case tested engine works unstable with extremely high toxic gases emission. Some physical properties of tested fuels, measurement system configuration, Values of mean indicated pressure vs. cycle number for AD3.152 engine fuelled with: pure diesel oil, ETIO, ET20, ET30, ET 40, ET50, Variations of unrepeatability index of mean indicated pressure in relationship to kind of tested fuels are presented In the paper. Research shows that tested engine is not possible to operate with using above 40% of ethanol content in diesel oil, as the fuel simply will not ignite.
Źródło:
Journal of KONES; 2009, 16, 2; 279-284
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Possibility of using visualization to present running point of marine diesel engine
Autorzy:
Krzyżanowski, J.
Witkowski, K.
Powiązania:
https://bibliotekanauki.pl/articles/246958.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
monitoring
marine diesel engine
torque
field of work engine
Opis:
The following paper introduces us to possibility of using visualization to present running point of main marine diesel engine during ship operation. Construction development of ship marine diesel engine going towards more and more power results in large mechanical and thermal load. So ship marine diesel engines of new generation are more susceptible to damage caused by overloading than the ones of older generation. For this reason more and more attention is paid to proper operation of these main marine engines understood as the way of choosing the right parameters resulting in adequate point of engine operation. This kind of exploitation is being reflected in more and more rigorous requirements imposed by ship engine producers concerning the conditions of their exploitation. This paper presents measured parameters during engine operation and of the sometime confirming its current performance. Special attention has been paid to the measurement of torque. Measurement of torque and revolution speed of the main marine diesel engine have been linked with the possibility of visual presentation of running point of the engine. By means of research carried out of HCP Engine Test Bed it was possible to prove effectiveness of succession of measurement instruments and torque meter action. Visualization algorithm which can be used to present field of work and running point of the engine has also been tested.
Źródło:
Journal of KONES; 2010, 17, 2; 271-275
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Premixed combustion of acetylene-hydrogen fuel mixtures for thermodynamic state generation in a constant volume combustion vessel
Autorzy:
Johnson, S.
Nesbitt, J.
Lee, S. -Y.
Naber, J. D.
Powiązania:
https://bibliotekanauki.pl/articles/242374.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engine
diesel engine
combustion processes
pressure vessel
preborn
Opis:
Flammability limits and flame speeds of dilute-lean fuel mixtures of hydrogen (H2) and acetylem premixed with oxygen (02) and nitrogen (N2) were examined with a detailed kinetics model. These mixtures are used in a preburn in a constant volume combustion vessel to create elevated temperatures and pressures with gas compositions that represent the thermodynamic state in a diesel engine combustion chamber at fuel injection and auto ignition. A mixture of hydrogen and acetylene with combined atomic hydrogen to carbon ratio (HCR) of 1.85 was used to match that of typical diesel fuel and results are shown in comparison to a previously used mixture with a HCR of 1.17. The lower flammability limit (LFL) of the HCR 1.85 fuel mixture was found at an equivalence ratio of 0.235, while flame speed and adiabatic combustion temperatures were also predicted for post preburn product oxygen levels between O and 21 percent. Flame speeds were shown to decrease with a reduction in oxygen concentration, an increase in nitrogen dilution, while combustion temperatures increased over most of this range. Trends for this relation of flame speed and temperature are presented and a new premixed fuel mixture with an HCR of 1.85 is proposed.
Źródło:
Journal of KONES; 2009, 16, 2; 199-208
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The application of non-converted vegetable oils in contemporary self-ignition engines
Autorzy:
Reksa, M.
Powiązania:
https://bibliotekanauki.pl/articles/245366.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
combustion engines
vegetable oils
diesel engine
alternative fuels
Opis:
The paper presents a test of a self-ignition engine equipped with high-pressure fuel-dosing system based on injection units with electronic control system. The engine was fuelled with conventional fuel and few kinds of non-converted vegetable oil. The analysis of the experiment results correlated with knowledge of their properties shows the important conclusions about possibilities, disadvantages and perspectives of the fuels usage in contemporary engines equipped with electronic control fuel-dosing system. The vegetable oils have a special place in history of automotive industry. In 1900 a great event on Word Trades in Paris was compression-ignition engine fuelled by groundnuts oil — a masterpiece of no one else like Rudolf Diesel. R. Diesel, aware of conventional fuels limitation, patented in 1892 a vegetable oil as a fuel. The NOx concentration in exhaust was measuredfor maximum engine speed (1900 rpm). The lowest emission ofmeasured compounds was observed in case of sunflower oil and rape oil "Biedronka" (65% and 75% of emission during engine work fuelled by conventional diesel oil). The highest values were detected for post frying palm oil and rape oil "Aldi" (120% of emission during engine work fuelled by conventional diesel oil).
Źródło:
Journal of KONES; 2009, 16, 4; 385-391
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biogas as a fuel for diesel engines
Autorzy:
Wierzbicki, S.
Powiązania:
https://bibliotekanauki.pl/articles/246845.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
biogas
methane
diesel engine
dual-fuel supply system
Opis:
The pursuit of reduced greenhouse gas emissions, as well as the increased share of renewable fuels in the overall energy balance has led to a search for alternative energy sources. One of the fuels on which great hopes are set as fuel for engines is biomethane or biogas, whose main component is methane. Biogas can be obtained from different products by using different technologies, so that it has potential as a widelyavailable fuel, which is quite easy to produce. The percentage of methane in biogas depends on the technology for obtaining biogas and ranges from 35% to around 75%. The largest biogas sources can be animal farms, where it is obtained from animal excrement. Another source is sewage treatment plants and rubbish dumps, where substantial quantities of biogas are obtained as a result of natural processes occurring in waste dumping sites or sewage. Biogas can also be acquired from waste obtained from fruit and vegetable processing as well as waste from meat plants. This paper examines the possibility of using biogas as a fuel for diesel engines. In these engines, the combustion of biogas (methane) requires the application of a dual-fuel supply system in which liquid fuel initiating gas fuel selfignition will be injected into the combustion chamber along with methane. The paper also contains example results showing the effect of the methane dose on the course of the combustion process in diesel engines.
Źródło:
Journal of KONES; 2012, 19, 3; 477-482
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research of usage of RRME and alcohol biofuel mixture in diesel engine
Autorzy:
Lebedevas, S.
Lebedeva, G.
Žaglinskis, J.
Powiązania:
https://bibliotekanauki.pl/articles/246865.pdf
Data publikacji:
2012
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
biodiesel
biofuel
diesel engine
environmental and energy parameters
Opis:
The paper provides the results of an integrated research of the energy, environmental performance and traction indicators and the characteristics of fuel feed and performance of A41, 2F511, VALMET 320 DMG and Audi 1Z highspeed, direct-injection diesel engines when converting their operation from mineral diesel D to the fatty acid esters (RRME and RRBE) and alcohol biodiesel mixtures. The researches are carried out in cooperation of the Lithuanian and Polish partners within the framework of joint scientific projects under EUREKA international scientific program „E!4018 CAMELINA-BIOFUEL”. In the light of the new EU initiatives („White Paper” 2011), 30% optimum part of RRME bio-component in the mixture with D (B30) is validated for practical use. The characteristics of fuel supply and heat generation in a diesel cylinder are under investigation; an explanation of a significant reduction in the harmful component emission (EG) and 2 to 4% increase in the fuel efficiency in case of use of B30 and B10 biodiesels is offered. The presence of the ethanol alcohol component 9E) in D-RME-E and RME-E biofuel mixtures resulted in reduction of CO and NOx emission by 10 to 12% and EG smokiness - by 20% per each 10% increase of E part. The indicated efficiency of performance was increased by 2-2.5%. The indicators of cyclic instability did not exceed the corresponding indicators in diesel operation on D. It is established that the motor properties of tested B30 and B50 biofuels based on butanol and rapeseed oil butyl ester RBE are similar to RME biodiesels and have important advantages over them: the complete solubility of alcohol component and the possibility of B30 (D-RBE) use at ambient temperature up to -30 centigrade. The motor characteristics of the second-generation biodiesels produced from the non-food raw material (Camelina Sativa oil methyl esters) are highly competitive with and even exceed by separate indicators the similar indicators of certified RME biodiesels. It is demonstrated that the conversion of diesels, including the automobile diesels with EGR electronic system, to operation on D-RRME (RME, CSME) biodiesels does not require the change of regulation characteristics of the fuel-feed system. The test of the oxidation stability of D-RME and D-CSME biodiesels performed under operating conditions on S. Lebedevas, G. Lebedeva, J. Žaglinskis VALMET 320 DMG marine diesel proved the stability of the motor, energy, and environmental performance indicators for 7-8 months' biodiesel storage without the addition of antioxidant and for 13-14 months' storage - with the addition of Ionol BS200 antioxidant.
Źródło:
Journal of KONES; 2012, 19, 2; 289-304
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Assessment of ships engine effective power, fuel consumption and emission using the vessel speed
Autorzy:
Borkowski, T.
Kasyk, L.
Kowalak, P.
Powiązania:
https://bibliotekanauki.pl/articles/247151.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
ships
main propulsion
marine diesel engine
exhaust emission
Opis:
Currently, the Baltic Sea States suggests a proposal to designate the Baltic Sea as an Emission Control Area for nitrogen oxides, in accordance with Annex VI of MARPOL73/78. The emission would be estimated on the data produced by the AIS (Automatic Identification System) system that is compulsory for ships. Therefore, exhaust emission of the ships' can be computed using the actual speed and main propulsion shaft power. Mostly, main propulsion engines' exhaust emission is dependent to realistic performance and can be determined. The research plan has been prepared, aimed an evaluating the main propulsion engine performance and emissions. In cooperation with the ship owner, the experimental program onboard the container vessel, equipped with latest large bore, two-stroke, and slow speed MAN B&W electronic controlled engine was carried out. The records set of vessel speed and related engine shaft power, fuel consumption and exhaust emission for container vessel is formed. Taking into account; main engine performance, types of fuel and other input data, the emission factors were determined for ship sea service state. Main engine shaft power estimation and measurement setup, examples of main engine shaft power, the shaft power equation coefficients density, example of main engine service operation, fuel oil consumption group, the ship speed estimated form, example of main engine area operation influenced by weather conditions are presented in the paper.
Źródło:
Journal of KONES; 2011, 18, 2; 31-39
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Monitoring of torsional vibration of a crankshaft by instantaneous angular speed observations
Autorzy:
Dereszewski, M.
Powiązania:
https://bibliotekanauki.pl/articles/242907.pdf
Data publikacji:
2016
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diagnostics
diesel engine
torsional vibrations
torque
angular speed
Opis:
Continuous monitoring of diesel engine performance under its operating is critical for prediction of malfunction development and subsequently functional failure detection. Analysis of Instantaneous angular Speed (IAS) of the crankshaft is considered as one of non-intrusive and effective method of detection of combustion quality deterioration. The paper contains presentation of attempt of monitoring of piston engine’s crankshaft torsional vibrations by measurement of Instantaneous Angular Speed at free and power output ends of the engine. It is assumed that calculation of differential value of angular distance run between both ends in the same time shall give the picture of torsion angle magnitudes and phases of the peak values. Fir carrying out such measurements, high frequency of sampling was required. The angular speed measurements is to be done utilising two optical sensors for reading and two perforated discs mounted at shaft’s ends playing the role of speed signal emitters. In the paper is presented description of the measurement system and explanation of its mode of work. It is also shown analysis of measurement accuracy, way errors elimination and method of signals runs filtration. Presented results of experiment derives from test cycle carried out using laboratory stand of Gdynia Maritime University equipped with 3- cylinder self - ignition engine, powering electric generator.
Źródło:
Journal of KONES; 2016, 23, 1; 99-106
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Validation of reference sampling for failure detection by crankshaft angular speed analysis
Autorzy:
Dereszewski, M.
Charchalis, A.
Powiązania:
https://bibliotekanauki.pl/articles/243825.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diagnostics
marine diesel engine
angular speed
reference comparison
Opis:
The paper presents results of the experiment focused on evaluation of records of runs of the engine in good condition as a reference for subsequent detection of faults of fuel system of medium speed diesel engine. The aim of research was determination of limits of instantaneous angular speed's spread spotted between random starts of the engine, without any fault condition simulation. Due to fine variation of the load setup and different ambient condition, every record of angular speed of independent starting, despite of attempts to sustain the same load and rotational speed value, presents some deviations between runs. Having on mind utilization of such measurement as a template for further comparison, is crucial to find out how random changes of ambient conditions and accuracy of revolutionary speed setup affect the IAS magnitude course. The answer was got in way of registration of numerous runs of the test engine after independent starts and hand adjustment of required RPM’s. The experiment was carried out at laboratory stand in GdyniaMaritimeUniversity, equipped with diesel engine Sulzer 3AL 25/30 driving electrogenerator. Sulzer 3AL 25/30 is three cylinder, medium speed, four stroke marine diesel engine, with maximum output 400 kW at 750 rpm. Independent records were treated as random variable and were compared each other. Obtained results were compared with differences between healthy engine and with simulated malfunctions of fuel injection.
Źródło:
Journal of KONES; 2014, 21, 4; 63-70
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of diesel fuel mixture and camelina oil ester on the process of fuel injection in traction engine
Autorzy:
Orliński, S.
Orliński, P.
Wojs, M. K.
Powiązania:
https://bibliotekanauki.pl/articles/246900.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
fuel plant
process of injection
engine test bench diesel engine
Opis:
This paper presents the results of comparative research on basic physical and chemical properties of pure diesel fuel and two types’ mixtures of Camelina oil ester (Camelina oil ester content of the mixture was 10% and 15%) and diesel fuel. Application of these mixtures has different physicochemical properties to power supply diesel engine, made it possible to detect existing differences in the injection process (pumping and spraying). The analysis of the injection process has been defined through experimental graphs of the fuel pressure in injection line and registered height of the needle injector. With the knowledge of these two fast-changing engine parameters and loadvelocity conditions, there were calculated: fuel flow speed from nozzle, range and fuel spray disintegration time and the average critical diameter of the droplets. In the final part of the article it was shown, that the fuel with different physicochemical properties has a significant impact on the injection process. There were also made a comparative assessment of the suitability test compounds for use in service.
Źródło:
Journal of KONES; 2013, 20, 1; 255-261
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Validation of reference sampling for failure detection by crankshaft angular speed analysis
Autorzy:
Dereszewski, M.
Charchalis, A.
Powiązania:
https://bibliotekanauki.pl/articles/247164.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diagnostics
marine diesel engine
angular speed
reference comparison
Opis:
The paper presents results of the experiment focused on evaluation of records of runs of the engine in good condition as a reference for subsequent detection of faults of fuel system of medium speed diesel engine. The aim of research was determination of limits of instantaneous angular speed's spread spotted between random starts of the engine, without any fault condition simulation. Due to fine variation of the load setup and different ambient condition, every record of angular speed of independent starting, despite of attempts to sustain the same load and rotational speed value, presents some deviations between runs. Having on mind utilization of such measurement as a template for further comparison, is crucial to find out how random changes of ambient conditions and accuracy of revolutionary speed setup affect the IAS magnitude course. The answer was got in way of registration of numerous runs of the test engine after independent starts and hand adjustment of required RPM’s. The experiment was carried out at laboratory stand in Gdynia Maritime University, equipped with diesel engine Sulzer 3AL 25/30 driving electrogenerator. Sulzer 3AL 25/30 is three cylinder, medium speed, four stroke marine diesel engine, with maximum output 400 kW at 750 rpm. Independent records were treated as random variable and were compared each other. Obtained results were compared with differences between healthy engine and with simulated malfunctions of fuel injection.
Źródło:
Journal of KONES; 2014, 21, 3; 67-74
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of fuel pollutants on operating parameters of contemporary fuel injector
Autorzy:
Osipowicz, T.
Stoeck, T.
Gołębiewski, W.
Powiązania:
https://bibliotekanauki.pl/articles/247182.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
fuel injector
diesel engine
common rail injection systems
Opis:
Article describes the operation issues of contemporary injection systems of Diesel engines. Common-rail system has been used since 1997, and since then there has been a significant evolution in its construction. In this aspect, there are changes in generations of high-pressure injection pumps and fuel injectors as well as methods of steering them, but exploitation problems are the same. The most prone to malfunction elements of the system are the fuel injectors. Their task is to distribute and to spray of the fuel in the combustion chamber of engine. Common Rail fuel injectors generate few injection dosages in the one work cycle. The rate of injection is depended on the design of the steering valve. One very important parameter of fuel injector is fuel injection delay time. If the time from control start of fuel injector to begin injection is shorter then it causes generation of greater number of injection dosages. Pollutants in fuel in the form of various amorphous solids of the size an even few microns cause the decrease of operating parameters of injector, which adversely affects the operation of the engine. Article shows contemporary fuel injectors, the methods of their examination, the types of fuel pollutants and their impact on fuel injector work.
Źródło:
Journal of KONES; 2015, 22, 3; 169-174
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of indicator and heat release graphs for vw 1.9 tdi engine supplied diesel fuel and rapeseed methyl esters (RME)
Autorzy:
Cisek, J.
Powiązania:
https://bibliotekanauki.pl/articles/247568.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
RME
FAME
indicator diagrams
heat realise
diesel engine
Opis:
The results of investigation of 1,9 TDI engine (285 Nm, 85 kW, type AJM without any modification) equipped with injection units supplied conventional diesel fuel (ON) or B100 fuel (RME) have been presented in article. Investigations have been realized at the engine speed of 2000 rpm and variable load within the range of 0 to 275 Nm. The pressure, temperature and heat release velocity runs have been subjected to analysis. Particular attention has been paid to the release of the heat used for the effective work and internal energy increase of the working medium (enthalpy) during combustion inside the engine cylinder versus the crank angle for both investigated fuels. It was found among the others that mentioned fuels differ in the heat release, heat velocity and the maximal combustion temperature, which for the B100 fuel is bigger than for the conventional diesel fuel. Bigger combustion dynamics of tested biofuel (compared with standard diesel fuel) results higher concentrations of Nitrogen Oxides NOx in exhaust gases. The easiest way is of course the use of the later start of fuel injection biofuels and/or increase the exhaust gas recirculation EGR. These treatments, however, result in a worsening of the energy performance of the engine. It was concluded also that the combustion of RME works properly at higher engine loads. Then reduce the negative difference between the combustion of biofuel (RME) and standard Diesel fuel.
Źródło:
Journal of KONES; 2013, 20, 4; 71-78
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Method for modelling temperature distribution in exhaust system of diesel engine in the light of mine systems of heat recuperation
Autorzy:
Chuchnowski, W.
Tokarczyk, J.
Stankiewicz, K.
Woszczyński, M.
Powiązania:
https://bibliotekanauki.pl/articles/242169.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
recuperation
diesel engine
Peltier's cell
temperature distribution
CFD
Opis:
Analysis of temperature distribution and heat flow in the exhaust system of diesel engine to determine technical parameters of the system for heat recuperation and changing of thermal energy into electric energy was presented. Temperature of exhaust gases as well as geometrical and material features of exhaust system were the input data accepted for modelling. Computational Fluid Dynamics (CFD) was used to determine temperature distribution in the exhaust system. The software by use numerical methods finite volume method) enables solving partial differential equations consisting of equations of: continuity, Navier-Stokes, Fourier-Kirchoff and complemented with other equations important as regards the discussed phenomenon (e.g. with turbulences models)transforming them in the algebraic equations or common differential equations. CFD software enables gaining some information as regards flow rate, distribution of speed field, and pressure field as well as heat flow, temperature field and mass field. Design and principle of operation of Peltier 's cell, model of recuperator, exhaust system, and diesel engine, finite elements meshing, boundary conditions assumed in analysis of exhaust gases and water flow, distribution of temperature field (maximal temperature of scale 335 K and maximal temperature of scale 400 K) on external wall of exhaust system and cross-section of exhaust system are presented in the paper.
Źródło:
Journal of KONES; 2011, 18, 2; 101-108
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Processing of long lasting signals of torsional vibrations measured using incremental encoders
Autorzy:
Dereszewski, M.
Sikora, G.
Powiązania:
https://bibliotekanauki.pl/articles/243279.pdf
Data publikacji:
2018
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
diagnostics
diesel engine
torsional vibrations
torque
angular speed
Opis:
The article describes processing method of a signal, coming from torsional deflections of an internal combustion piston engine’s crankshaft, registered using two optical encoders ETNP-10. Standard measurement and recording set ETNP-10 enables recording of Instantaneous Angular Speed values encompassing 10 revolutions of the crankshaft, what is equal to 5 cycles of four-stroke engine. That time duration is sufficient for analysis of changes of angular speed caused by, for example, malfunction of fuel injection valve, but is insufficient in case of observation characterized by low frequency changes with period of fluctuations, lower than 0.8 sec. Short time for recording makes impossible following of instantaneous angular speed deviations caused by magnitude modulation of engine’s load value. In the article is presented an algorithm written in MATLAB environment, which allows processing of the data recorded using the recorder DAS 1600 Sefram. The recorded this way signals have around 26 seconds' duration of engine work. Data acquired from two encoders mounted at opposite sides of the shaft, in form of square magnitude signals are transformed into instantaneous speed and subsequently to instantaneous angular shift, what is basis for torsions calculation. In the article is also presented method of elimination of systematic error due to assumed method of averaging. Finally, some examples of results of torsional deflection measurement and analysis are presented.
Źródło:
Journal of KONES; 2018, 25, 4; 59-65
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of Pt active coating application inside diesel engine on polycyclic aromatic hydrocarbons (PAHS) emission
Autorzy:
Janicka, A
Walkowiak, W.
Szczepaniak, W.
Powiązania:
https://bibliotekanauki.pl/articles/244056.pdf
Data publikacji:
2008
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
active coating
catalyst
polycyclic aromatic hydrocarbons
diesel engine
Opis:
Application of active coating inside of an self-ignition engine may have an important impact on several stages of combustion process: fuel cracking, fore-flame phase, combustion phase and secondary combustion phase [7]. Investigations of such construction are very rare in the literature - especially of hydrocarbons emission. Polycyclic aromatic hydrocarbons (PAHs) are known to have mutagenic and carcinogenic effect on humans [2, 6, 7]. One of the most important anthropogenic sources of these substances is motorization (especially diesel engines). The paper presents results of measurements of PAHs emissions from SB3.1 self-ignition engine with Pt active coating application inside. The catalyst was applied on engine valves surface. Zirconium ceramic was chosen as a coating for catalyst application (also because of its thermo-insulating properties). Because of unstable parameters of self-ignition engine work (pressure and temperature jumps), PAHs were extracted from two phases: gas phase and solid phase (particle matter - PM). A chromatographic method of PAHs identification and analysis, because of their low level of concentration in exhaust gases, needed to be supported by sample purification and enrichment stages [40]. It has been found that a significant decrease of total toxic polycyclic aromatic hydrocarbons concentration in engine exhaust gases for engine with Pt catalyst application. The catalyst application causes also changes in relative concentrations of polycyclic aromatic hydrocarbons.
Źródło:
Journal of KONES; 2008, 15, 2; 131-136
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of RME on mass and number concentration of nano PM in exhaust gases from a diesel engine
Autorzy:
Cisek, J.
Powiązania:
https://bibliotekanauki.pl/articles/244532.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
nanoparticles
mass
number concentration
FAME
RME
diesel engine
Opis:
Transport is a major source of the particle pollution (PM). Combustion engine particulate emissions have the potential cause adverse health effects. These effects include cancer and other pulmonary and cardiovascular diseases. A substantial proportion of the number of particles, but not the mass, is ultrafine. For example – one million particles of 100 nanometers size with a unit density of 1 g/cm3 have a mass of approximately 0.0005 g. The paper includes research results of mass and number concentration of nanoPM for 1.9 TDI VW exhaust gases fuelled by standard diesel. The measurements were performed for ambient air and 3 different point of engine work (idle speed, low and high load at 2000 rpm). For nanoPM measurements was used Electrical Low Pressure Impactor ELPI from DECATI, was found, among other things, that the biggest mass concentration was at 0.1-10 μm of PM diameter but the biggest number concentration was at 0,01 – 0,1 μm and thus for the size of solid particles of at least an order of magnitude smaller than the mass concentration. The biggest the negative differences in the mass concentration occur in the exhaust gases of the RME fuelled engine (in comparison with diesel fuel) at engine idling when the smallest injection pressure and temperature inside the engine cylinder exist and the oxygen availability is also the lowest (because of the small charging pressure and high EGR rate). Such measurements are important not only in terms of utilitarian but also in cognitive sense – for determining the effect of the engine construction parameters and/or regulating the engine (or the fuel composition) on the mass and the number of nanoparticles emitted in the exhaust gases.
Źródło:
Journal of KONES; 2014, 21, 2; 53-60
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A study of emission reduction by using alcohol blend fuel for small diesel engine
Autorzy:
Kawakami, T.
Powiązania:
https://bibliotekanauki.pl/articles/244564.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
low emission
small diesel engine
alcohol blend fuel
Opis:
In practical diesel engines it is to achieve a low emission and low fuel consumption under from low to high load operation conditions. Several techniques were developed for the low emission and high efficiency, such as Homogeneous Charge Compression-Ignition Engines and the blend fuels. Nevertheless, there are only few data available for reducing the emissions and fuel consumption of small diesel engines by using blend fuels. This experiment has been carried out to examine the influence of alcohol blend fuels on combustion characteristics for small diesel engine. The fuels used in this study are light oil (Standard), ethanol, propanol and butanol. The combustion behaviours, such as the emissions in exhaust gas (NOX, CO, CO2, O2 concentration), fuel consumption rate are observed. The main conclusions are as follows: 1) it is possible to control the combustion behaviour by using alcohol blend fuels for small diesel engine, 2) the fuel consumption of at any alcohol blend fuels is bigger than that of light oil, 3) the net thermal efficiency of some alcohol blend fuels (E5P5, P5B5, E5B5) slightly increases than that of light oil, 4) the NOx emissions for all the alcohol blend fuels are smaller than that of light oil, 5) the CO emissions are remarkably bigger than that of light oil under from low to middle engine load without the ethanol 10% addition.
Źródło:
Journal of KONES; 2014, 21, 1; 125-130
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cycle-to-cycle variations of a diesel engine operating with palm biodiesel
Autorzy:
Yasin, M. H.
Mamat, R.
Abdullah, A. A.
Abdullah, N. R.
Wyszynski, M. L.
Powiązania:
https://bibliotekanauki.pl/articles/950092.pdf
Data publikacji:
2013
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
cycle-to-cycle variations
biodiesel
combustion
diesel engine
Opis:
Biodiesel is one of biodegradable and renewable fuel, which is originated from vegetable oil or animal fats. Different fuel properties of biodiesel produce different combustion characteristics which slightly differ to mineral diesel. Combustion studies on palm-biodiesel and mineral diesel were conducted using a multi-cylinder diesel engine operating at medium engine load at 2500 rpm. The engine was water cooled inline four cylinder diesel engines without exhaust gas recirculation system. Cycle-to-cycle variations of peak cylinder pressure and mean indicated pressure of the test fuels were determined for the combustion characteristics of diesel engine. In-cylinder pressure data for the 200 consecutive cycles were determined using a Kistler pressure transducer and recorded into a combustion analyser. Three different engine loads: 20%, 40% and 60% were selected in this study with a constant engine speed of 2500 rpm. The results show that at lower load, in-cylinder pressure variations for palm biodiesel were lower compared to mineral diesel. However, at medium and high loads, palm biodiesel has dominated the peak cylinder variations. Different combustion cyclic variations for mineral diesel and B100 are observed and generally influenced by psychochemical properties differences including viscosity and density of fuel.
Źródło:
Journal of KONES; 2013, 20, 3; 443-450
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies