Autor: Pawletko, R. - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: The possibility of fuel injection pump diagnosis on the basis of indicator diagram
Autorzy:: Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/246551.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: indicator diagram
heat release characteristics
marine diesel engine diagnosis
fuel pump leakage
Opis:: The paper presents the results research related to the possibility of fuel injection pump diagnosis on the basis of indicator diagram. The study was conducted on a laboratory four-stroke marine engine, type Sulzer 3Al 25/30, with nominal power Nen = 408 kW at nominal rotational speed n = 750 rpm. The study was carried out according to active experiment plan, during which the engine failure of the injection system was simulated. Simulation of fuel pump leakage was completed by the opening of the adjusting screw on the pump discharge. Measurements were made at a constant engine speed of 750 rev/min for five loads: 50, 100, 150, 200, 250 kW. Measurements of pressure of combustion were performed by means of tensometric sensors of Spice Company. Based on measured pressure curves heat release characteristics were determined. The algorithm allows the determination of net heat release rate q and the net generated heat Q characteristics. Based on the obtained results it can be concluded that significant improvement in the diagnostic use of indicator diagrams can be obtained by using heat release characteristics. These characteristics are correlated with the process of fuel injection and the injection pump operation. As demonstrated in the work of analyzing the heat release rate q, it is possible to infer diagnosis on the technical condition of the fuel injection system.
Źródło:: Journal of KONES; 2014, 21, 1; 215-221
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: The use of the expert system in diagnostic of marine diesel engines
Wykorzystanie systemu ekspertowego do diagnozowania okrętowego silnika spalinowego
Autorzy:: Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/243052.pdf
Data publikacji:: 2007
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: diagnostyka techniczna
systemy ekspertowe
silniki spalinowe
pozyskiwanie wiedzy ekspertowej
technical diagnostic
expert systems
combustion engines
expert knowledge acquisition
Opis:: W artykule przedstawiono wyniki pierwszego etapu badań związanych z tworzeniem systemu ekspertowego do diagnozowania okrętowego silnika tłokowego. Scharakteryzowano dekompozycję silnika okrętowego na układy funkcjonalne oraz zidentyfikowano podstawowe źródła wiedzy ekspertowej, które mogą być wykorzystane podczas tworzenia bazy wiedzy. Podjęto próbę pozyskania podstawowej wiedzy z dziedziny eksploatacji silników, dotyczącą najsłabszych ogniw silnika, rodzaju występujących uszkodzeń silników oraz podstawowych relacji diagnostycznych, umożliwiających ocenę stanu technicznego. Grupę ekspertów stanowili doświadczeni oficerowie mechanicy floty handlowej. Do pozyskiwania wiedzy od ekspertów zastosowano wywiad kwestionariuszowy. W szczególności metodologia pozyskiwania oraz sposób reprezentacji wiedzy przybliżonej, wyniki badań częstości występowania uszkodzeń wyodrębnione przez ekspertów symptomy uszkodzeń, diagnozowanie uszkodzeń układu paliwowego są prezentowane w artykule. Parametry wyodrębnione przez ekspertów nie umożliwiają jednak lokalizacji uszkodzeń. Szczególne interesujące wydają się tutaj metody umożliwiające automatyczne pozyskiwanie wiedzy z baz danych. Uzyskane wyniki będą weryfikowane na stanowisku laboratoryjnym.
In the paper the first stage of research relevant to the marine diesel engine diagnostic expert system is presented. The decomposition of diesel engine to diagnostic subsystems is described. Basic sources of knowledge which can be used for construction of knowledge data set are also identified. The basic knowledge related to the marine diesel exploitation was undertaken. That expert knowledge covers the weakness point of engine, the kind of faults and diagnostic relation between faults and their symptoms. The group of experts was contained the experienced merchant navy officers. The paper questionnaire was used to the knowledge acquisition. Particularly the methodology of obtaining the representation way of the approximate knowledge, test results of the frequency of the damage occurring distinguished by experts' symptoms of damages, diagnosing of damages of fuel systems are presented in paper. However distinguished parameters by experts do not make possible location of damages. Special interesting seem here methods making possible automatic knowledge acquisition from databases. The acquired knowledge will be verified on the laboratory engine in the future.
Źródło:: Journal of KONES; 2007, 14, 2; 363-372
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: Increasing the accuracy of the mean indicated pressure determination by appointment of the TDC cylinder position
Autorzy:: Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/243489.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: Top Dead Centre determination
Mean Indicated Pressure accuracy
indicator diagram analysis
Opis:: The paper describes the problems of mean indicated pressure determination and the piston TDC (Top Dead Centre) position impact on this parameter in marine diesel engines. Mean indicated pressure Pi is one of the most important diagnostic parameters of marine engines. On the basis of its parameter, the assessment of the technical condition of each cylinder as well as the regulation of injection equipment can be made. Most of the available electronic indicators enable automatic calculation of mean indicated pressure on the basis of progress indicator diagram. As the research shows the greatest impact on the accuracy of the designation mean indicated pressure has errors of piston TDC position. These errors can be significant and therefore this may lead to engine misdiagnosis. The actual piston TDC correction methods were discussed, and they justified the need of their use in marine engines, despite the wide use of methods of determining the angular position of the crankshaft. The original method of TDC correction based on the model of curve of the compression with the exponent of a polynomial was introduced. The proposed method of TDC correction has been verified for a different types of marine engines.
Źródło:: Journal of KONES; 2014, 21, 2; 251-258
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: Influence of the indicator diagrams smoothing on the indicated parameters of marine diesel engines
Autorzy:: Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/244800.pdf
Data publikacji:: 2015
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: indicator diagrams
smoothing the interference
engine indicated parameters
Opis:: The topic of this article is to analyze the influence of indicator diagrams smoothing methods on diagnostic parameters determined on their basis such as the maximum combustion pressure, mean indication pressure and heat release characteristics. Indicator diagrams of marine engines are subject to serious distortions arising primarily from the measuring method for in-cylinder pressure. Measurements are performed on the indicator valve which connect with the combustion chamber through the indicator channel. Depending on the engine design the channel length can reach a considerable length and introduces significant distortion in both the phase and amplitude of the pressure signal. Further analysis of the indicator diagram eg. in order to determine the heat release characteristics requires the use of methods of smoothing and filtering of interference. The results confirm no effect of indicator diagram smoothing for the value of the mean indicated pressure, which is one for the most important indicated parameters. A significant influence of smoothing on the maximum value of the heat release rate was observed. The differences in this case exceed 50%. At the same time confirmed that the heat release rate curve determined on the basis of a diagram without smoothing, carry a high level of interference, which precludes their practical use. Smoothing allows getting heat release rate curves that carry vital information about the working process of the engine.
Źródło:: Journal of KONES; 2015, 22, 2; 169-176
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Increasing the accuracy of the mean indicated pressure determination by appointment of the TDC cylinder position
Autorzy:: Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/245110.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: Top Dead Centre determination
Mean Indicated Pressure accuracy
indicator diagram analysis
Opis:: The paper describes the problems of mean indicated pressure determination and the piston TDC (Top Dead Centre) position impact on this parameter in marine diesel engines. Mean indicated pressure Pi is one of the most important diagnostic parameters of marine engines. On the basis of his parameter, the assessment of the technical condition of each cylinder as well as the regulation of injection equipment can be made. Most of the available electronic indicators enable automatic calculation of mean indicated pressure on the basis of progress indicator diagram. As the research shows the greatest impact on the accuracy of the designation mean indicated pressure has errors of piston TDC position. These errors can be significant and therefore this may lead to engine misdiagnosis. The actual TDC piston correction methods were discussed, and were justified the need of their use in marine engines, despite the wide use of methods of determining the angular position of the crankshaft. The original method of TDC correction based on the model of curve of the compression with the exponent of a polynomial was introduced. The proposed method of TDC correction has been verified for different types of marine engines.
Źródło:: Journal of KONES; 2014, 21, 4; 397-404
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 6.

Tytuł:: Knowledge acquisition for marine diesel engine diagnosis
Pozyskiwanie wiedzy dla potrzeb diagnozowania okrętowego silnika spalinowego
Autorzy:: Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/244833.pdf
Data publikacji:: 2008
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: systemy ekspertowe
silniki spalinowe
pozyskiwanie wiedzy ekspertowej
diagnostyka techniczna
combustion engines
expert knowledge acquisition
technical diagnostic
expert systems
Opis:: W artykule przedstawiono koncepcję systemu diagnostycznego okrętowego silnika tłokowego opartą na modelu systemu ekspertowego. Zrealizowano pozyskiwanie wiedzy diagnostycznej, opracowano bazę wiedzy oraz zaproponowano ogólną strukturę systemu. Wiedza dla ekspertowego systemu diagnozowania silnika okrętowego została pozyskana od ekspertów (specjalistów w dziedzinie eksploatacji) oraz z diagnostycznych baz danych. Do pozyskiwania wiedzy od ekspertów zastosowano wywiad kwestionariuszowy. Grupę ekspertów stanowili doświadczeni oficerowie mechanicy floty handlowej. Podjęto próbę pozyskania podstawowej wiedzy z dziedziny eksploatacji silników obejmującą relacje diagnostyczne, umożliwiające ocenę stanu technicznego. Pozyskiwanie wiedzy z baz danych przeprowadzono z wykorzystaniem indukcyjnych metod uczenia maszynowego. Dane uczące dla algorytmów indukcji zostały zgromadzone w wyniku realizacji eksperymentu czynnego na silniku Sulzer 3Al 25/30. Porównano wyniki klasyfikacji stanów silnika uzyskane za pomocą algorytmów LEM2 oraz MODLEM. Oceny jakości działania poszczególnych klasyfikatorów dokonano techniką 10-fold cross validation. Badane algorytmy automatycznej indukcji, mogą być wykorzystywane do pozyskiwania wiedzy z baz danych, dla potrzeb diagnostycznego systemu ekspertowego.
In the paper conception of marine diesel engine diagnostic system based on expert system model was presented. The first stage of research relevant to knowledge acquisition for this system was done, knowledge data set was built and general structures of the expert system was proposed. Basic sources of knowledge, which can be used for construction of knowledge data set, are also identified. The basic knowledge related to the diesel diagnostic was undertaken from experts and diagnostic data base. The paper questionnaire was used to the knowledge acquisition from experts. The basic knowledge related to the marine diesel exploitation was undertaken. Those expert knowledge covers the weakness point of engine, the kind of faults and diagnostic relation between faults and their symptoms. The group of experts was contained the experienced merchant navy officers. The rule induction algorithms were used to knowledge acquisition from database. During the experiment efficiency of LEM induction algorithms was compared to new MODLEM algorithms. Training and test data were acquired from experiment on marine engine Sulzer 3AL 25/30. 10-fold cross validation method was used to estimation classification efficiency for different rule induction algorithms. Tested automatic induction algorithms can be used for knowledge acquisition from diagnostic data base for marine diesel engine diagnostic system.
Źródło:: Journal of KONES; 2008, 15, 4; 471-477
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 7.

Tytuł:: Knowledge acquisition from database for marine diesel engine diagnosis
Pozyskiwanie wiedzy z baz danych dla potrzeb diagnozowania okrętowego silnika spalinowego
Autorzy:: Charchalis, A.
Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/245763.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: diagnostyka techniczna
systemy ekspertowe
silniki spalinowe
pozyskiwanie wiedzy ekspertowej
technical diagnostic
expert systems
combustion engines
expert knowledge acquisition
Opis:: This article presents an attempt to use inductive machine learning methods to knowledge acquisition from the databases for the purpose of marine diesel engine diagnostic 's expert system. The existing methods of acquiring knowledge based on Information about the exploitation of technical objects stored in databases was characterizes. The selected machine learning methods was used to obtain the relationship in the form of diagnostic rules. The results obtained with algorithms LEM2, MODLEM and EXPLORE was compared. MODLEM algorithm allows the use of numerical data directly without having to pre-discretization. Learning examples stored in the diagnostic database was obtained as a result of the active experiment, carried out on laboratory Sulzer engine 3AL 25/30. During the experiment the damages of the turbocharging system, fuel injection system and combustion chamber was simulated. Only the elementary states (single damage in the same time) in a variable load were included. 10-fold cross validation techniąue was used for evaluation of the obtained rules classifiers. The obtained diagnostic rules have also been assessed in substantive terms, including an analysis of the relationship between disability states and received symptoms. Used machine learning techniques can be used for automatic knowledge acquisition for the diagnostic expert system.
W artykule przedstawiono próbę wykorzystania indukcyjnych metod uczenia maszynowego, do pozyskania wiedzy z baz danych dla potrzeb ekspertowego systemu diagnozowania okrętowego silnika tłokowego. Scharakteryzowano istniejące metody pozyskiwania wiedzy na podstawie informacji o przebiegu eksploatacji obiektów technicznych zapisanych w bazach danych. Zastosowano wybrane metody uczenia maszynowego do uzyskania relacji diagnostycznych w postaci reguł. Porównano wyniki uzyskane za pomocą algorytmów LEM2, MODLEM oraz EXPLORE. Algorytm MODLEM umożliwia wykorzystanie bezpośrednio danych numerycznych bez konieczności stosowania dyskretyzacji wstępnej. Przykłady uczące zapisane w diagnostycznej bazie danych uzyskano w wyniku realizacji eksperymentu czynnego, przeprowadzonego na silniku laboratoryjnym Sulzer 3AI 25/30. Podczas eksperymentu symulowano wybrane uszkodzenia układu wymiany czynnika roboczego, układu wtryskowego oraz komory spalania. Uwzględniono tylko stany elementarne (pojedyncze uszkodzenia w tym samym czasie) w warunkach zmiennego obciążenia. Oceny sprawności uzyskanych klasyfikatorów regułowych dokonano techniką 10-fold cross validation. Uzyskany zbiór reguł diagnostycznych został również poddany ocenie merytorycznej, obejmującą analizę związków pomiędzy diagnozowanymi stanami niezdatności a uzyskanymi symptomami. Wykorzystane techniki uczenia maszynowego mogą zostać zastosowane między innymi do automatycznego pozyskiwania wiedzy dla potrzeb systemu ekspertowego.
Źródło:: Journal of KONES; 2009, 16, 4; 37-42
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 8.

Tytuł:: Research of the influence of marine diesel engine Sulzer AL 25/30 load on theTDC position on the indication graph
Autorzy:: Pawletko, R.
Polanowski, S.
Powiązania:: https://bibliotekanauki.pl/articles/247411.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: kinematic TDC determination
load influence on TDC position
Opis:: The article presents the research results of load influence on errors of the piston Top Dead Centre (TDC) position determined on indication graph with combustion. For TDC determination the method proposed by Polanowski is applied. This method is based on least-squares approximation with model of thermodynamic compression using apolynomial exponent. So, designated TDC are kinematics. This method make possible determination the TDC on the indicator diagram with combustion, as well as the total compression ratio and the dynamic error of pressure (offset). Research were done on the laboratory engine Sulzer 3AL25/30 for load range of 50-250 kW and rotational speed 750 rpm, which corresponds to 15-90% nominal load. Cylinder pressures were recorded with a resolution ofn O.5 OWK by means of multichannel recorder UNITEST 205. For pressure measurements were applied strain gauge pressure sensors Spais Company. For the analysis of indicator diagrams used its own specially developed algorithm and program for the automatic determination of TDC, based on the model of the compression process with the exponent of the polynomial. Simultaneously three parameters were determined: the position of TDC, the total compression ratio and offset the pressure. Additionally set the position of the zeros of the second order derivatives, which are sometimes considered as reference points to TDC of pistons. For smoothing of indicator diagrams their own algorithms and programs of moving approximation by polynomials of 3rd degree was used. The results of research have shown the essential load influence on the errors of TDC positions on indicator diagrams.
Źródło:: Journal of KONES; 2010, 17, 3; 361-368
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 9.

Tytuł:: Knowledge management system for marine diesel engine diagnosis
Autorzy:: Charchalis, A.
Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/242163.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: knowledge management system
diagnostic expert system
marine diesel engine diagnosis
Opis:: The paper presents the conception of knowledge management system for a diagnostic expert system. Development of knowledge management system is necessary during the construction of the expert system. The most important reason is that knowledge in this system is not a static whole, but is subject to dynamic growth, is modified and updated. Advantages afforded by the creation of diagnostic systems based on knowledge, such as expert systems, compared to traditional diagnostic systems based on closed algorithms were characterized. The conception of knowledge management system established in the diagnostic work associated with the development of expert system for marine diesel engine diagnosis. The main elements of the developed management system are: dictionary editor, rule editor, knowledge assessment module and import and export module. Knowledge management system is also equipped with an electronic form that is used to obtain knowledge from experts, specialists in diesel engines operation. The article presents the tasks and the performance of individual components of the system. The knowledge management system enables integration within a single frame of both information collected from experts and automatically collected one. A doubtless advantage of expert system is the opportunity of updating and developing the content recorded in the database. Due to this feature, the effectiveness of the system may grow during engine operation and facilitate gaining new experience.
Źródło:: Journal of KONES; 2011, 18, 2; 77-83
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 10.

Tytuł:: Influence of clogged injector nozzles on the heat release characteristics
Autorzy:: Pawletko, R.
Polanowski, S.
Powiązania:: https://bibliotekanauki.pl/articles/243678.pdf
Data publikacji:: 2013
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: indicator diagram
heat release characteristics
marine diesel engine diagnosis
Opis:: The paper presents the results of research of the influence of clogged injector nozzles in fuel injection system on the shape of heat release characteristics. The study was conducted on a laboratory four-stroke marine engine, type Sulzer 3Al 25/30, with nominal power Ne = 408 kW at nominal rotational speed n = 750 rpm. The study was carried out according to active experiment plan, during which the engine failure of the injection system was simulated. Simulation of loss of patency of injector nozzles (clogged) was to completely clog two holes of nine injection injector nozzle holes with a diameter of 0,325 mm. Measurements were made at a constant engine speed of 750 rev/min for five loads: 50, 100, 150, 200, 250 kW. Measurements of pressure of combustion were performed by means of tensometric sensors of Spice Company. Based on measured pressure curves heat release characteristics were determined. The algorithm allows the determination of net heat release rate q and the net generated heat Q characteristics. Based on the obtained results it can be concluded that significant improvement in the diagnostic use of indicator diagrams can be obtained by using heat release characteristics. These characteristics are correlated with the process of fuel injection and the injection pump operation. As demonstrated in the work of analysing the heat release rate q, it is possible to infer diagnosis on the technical condition of the fuel injection system.
Źródło:: Journal of KONES; 2013, 20, 3; 307-314
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 11.

Tytuł:: Acquisition of diagnostic information from the indicator diagrams of marine engines using the electronic indicators
Autorzy:: Polanowski, S.
Pawletko, R.
Powiązania:: https://bibliotekanauki.pl/articles/246036.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: marine engines
engine indication
angular axis
pressure sensors
TDC
heat release characteristics
Opis:: The paper analyzes the factors influencing the quantity and quality of diagnostic information obtained by engine indication with electronic indicators and pressures analyzers. Amount of information obtained virtually unchanged since the advent of the first construction pressure analyzers produced by Autronica and ABB Company. In many cases, the value of the maximum combustion and compression pressures, can be measured using these devices with sufficient accuracy and reliability, is if ignition occurs after piston TDC. Determination of the mean indicated pressure, compression ratio and heat release characteristics required to develop a method of TDC determination on the indicator diagrams, generate reliable angular axes in real time and pressure sensors of sufficient accuracy. It should be noted that in the latest solution of ABB system, a correction of thermodynamic loss angle and combustion pressure sensors of high accuracy were introduced. For marine diesel engines diagnosis, the pressure sensor measuring sustainability is important because of the ability to create trends of specific diagnostic parameters, which may constitute an additional, important source of diagnostic information. The paper presents an overview of currently available pressure sensors that can be used during marine engines indication. Most important issues related to the pressure measurement on indicator valves were characterized. An assessment of the gas channels and the quality of the angular axis impact for the parameters of indicator graphs was done.
Źródło:: Journal of KONES; 2011, 18, 3; 359-366
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 12.

Tytuł:: Application of multiple moving approximation with polynomials in curve smoothing
Autorzy:: Pawletko, R.
Polanowski, S.
Powiązania:: https://bibliotekanauki.pl/articles/246390.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: multiple moving least-square approximation
decomposition and separation of disturbances
Opis:: The paper has characterized the method of multiple moving least-square approximation with polynomials, known as the Savitzky-Golay filter. This method enables smoothing the measurement series, decomposition and separation of disturbances, generation of derivatives as well as approximate integration of measurement series. The smoothing properties of the method as well as the possibilities of separation and decomposition of disturbances are shown on the examples of treatment of the selected indicator graph. The attention was paid to the need for additional application of special filters in case of abnormal impulse deviations. The examples show that in case of the analyzed curve, the results of smoothing by means of several wave filters from Wavelet Explorer package, are worse than those received with the methods of moving approximation. On the derivatives of smoothened curve by means of wavelet filters, there are significant oscillations, what is typical of the whole-interval approximation with spline functions. One should highlight the high simplicity of algorithms of multiple moving approximation and associated with this, high speed of operation, what particularly predisposes this method of data processing in an on-line mode. The authors presented their own proposals of programs for measurement data processing with the method of multiple moving approximation with polynomials, with the possibility of selection of an approximation polynomial to the fifth degree. The programs were developed in the Excel and Delphi environment.
Źródło:: Journal of KONES; 2010, 17, 2; 395-401
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 13.

Tytuł:: Influence of TDC determination methods on mean indicated pressure errors in marine diesel engines
Autorzy:: Pawletko, R.
Polanowski, S.
Powiązania:: https://bibliotekanauki.pl/articles/242218.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: TDC determination
coordinate of zero value of second derivative
TDC position influence on MIP errors
Opis:: The paper presents the results of comparative analysis of influence of different methods of TDC determination for the calculation errors of mean indicated pressure (MP). Lemag method based on zero point of first order derivative, used in PREMET pressure analyzers, was compared to the method based on a polynomial model of the compression process. Comparisons were made on the operating measurement data obtained on the low speed marine engine RTA96C which forms the main propulsion of the vessel and the medium speed engine MAN L28/32A. Measurements were made with onboard combustion PREMET analyzer. It was found that the method based on zero point of first order derivative can give the deviations of position of TDC in excess of 2°CA which is caused by disturbances associated with the measurement of pressure and interference associated with the generation of the angular axis. These errors are related to the accuracy of the methods of determining of the first derivative and the availability of a sufficient range of pure compression after TDC. The best results of determining the TDC position was obtained from the original method based on a polynomial model of the compression process. It should be emphasized that the proposed method enables individual adjustment of TDC for each cylinder and can be used even when the combustion begins before TDC. The conducted research proved the existence of significant influence of indicator graph TDC location on the mean indicated pressure calculation errors.
Źródło:: Journal of KONES; 2011, 18, 2; 355-363
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 14.

Tytuł:: Evaluation of current developments and trends in the diagnosis of marine diesel engines based on the indicator diagrams analysis
Autorzy:: Pawletko, R.
Polanowski, S.
Powiązania:: https://bibliotekanauki.pl/articles/244253.pdf
Data publikacji:: 2014
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: combustion pressure sensor
indicator diagram analysis
Opis:: The paper analyses the current offer of combustion pressure sensors for use on marine engines under operating conditions, methods of data acquisition, methods of determining TDC position and methods of obtaining diagnostic information from the indicator diagrams. Terms of continuous work on marine engines themselves only: new ABB cylinder pressure sensor, the piezoelectric sensors from KISTLER and AVL companies, but with limitations, the main ones being stability at high temperature. Another important issue for the accuracy of mean indicated pressure and heat released characteristics determination is referred to TDC position on the indicator diagrams. TDC is appropriate thermodynamic point, it is hardly determinable in the presence of interference and lack of sufficient information – but is used, for example in ABB solution. One of the sources of diagnostic information is to analyse trends in some parameters, which, unfortunately, is very difficult in environments with varying engine loads. Further progress in the diagnostic use of indicator diagrams should be associated with the use of the heat released characteristics and the net internal efficiency, which as shown by the results of preliminary tests can be used to assess the accuracy of the injection and combustion of fuel, including gas fuel. Supplementing these methods may be the use of vibration and noise to detect certain malfunctions.
Źródło:: Journal of KONES; 2014, 21, 4; 389-396
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 15.

Tytuł:: Assessment of the diagnostic suitability of net thermal efficiency of marine diesel engine
Autorzy:: Pawletko, R.
Polanowski, S.
Witkowski, A.
Powiązania:: https://bibliotekanauki.pl/articles/247360.pdf
Data publikacji:: 2013
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: indicator diagram
thermal efficiency
diesel engine diagnosis
Opis:: This article applies to searching for symptoms and diagnostic parameters pointing in a deterioration in the quality of the combustion process in marine diesel engines. It was assumed that diagnostic parameters should give clear information regardless of engine load or with respect to the mean indicated pressure. The proposed cycle and sectional net thermal (heat) efficiency characteristics and also dimensionless net heat release rate were analysed. In order to obtain the state of deterioration of the injection process simulation of discalibration (larger diameter) of injector holes was performed. The simulation was carried out by the enlarged of diameter of the injector holes form 0.375 mm to 0.385 mm. Deterioration of the formation and growth of fuel spray droplet diameter is result of such simulation. The study was conducted on a laboratory engine Sulzer Al25/30. The study was carried out according to active experiment plan, during which the selected engine failure of the injection system was simulated. Measurements of pressure of combustion were performed by means of tensometric sensors of Spice Company on the indicator valve. The analysis found that in the event of injector nozzle faults (discalibrated holes) significantly decreases the net thermal efficiency η c cycle, and there are significant oscillations of net
Źródło:: Journal of KONES; 2013, 20, 4; 327-332
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "Pawletko, R." wg kryterium: Autor

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język