Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "chłodzenie" wg kryterium: Temat


Wyświetlanie 1-11 z 11
Tytuł:
Model of heat transfer in the stagnation point of rapidly evaporating microjet
Autorzy:
Mikielewicz, D.
Muszyński, T.
Mikielewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/240462.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chłodzenie mikrojetowe
chłodzenie powierzchniowe
CHF
microjet cooling
surface cooling
Opis:
The paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 [my]m respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling but the boiling curves are showing a smaller value of critical heat flux (CHF) that the stagnant pool boiling. Values of CHF are also reduced with decreasing liquid subcooling. Theoretical model of surface cooling by evaporating microjet impingement in the stagnation point was described theoreticaly. Results of experiments were compared with predictions by the model showing a good consistency.
Źródło:
Archives of Thermodynamics; 2012, 33, 1; 139-152
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental investigation of single-phase microjet cooling of microelectronics
Autorzy:
Rusowicz, A.
Leszczyński, M.
Grzebielec, A.
Laskowski, R.
Powiązania:
https://bibliotekanauki.pl/articles/240614.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cooling
heat transfer
microjets
microprocessor
chłodzenie
wymiana ciepła
mikrojety
mikroprocesor
Opis:
Development of electronics, which aims to improve the functionality of electronic devices, aims at increasing the packing of transistors in a chip and boosting clock speed (the number of elementary operations per second). While pursuing this objective, one encounters the growing problem of thermal nature. Each switching of the logic state at the elementary level of an integrated circuit is associated with the generation of heat. Due to a large number of transistors and high clock speeds, higher heat flux is emitted by the microprocessor to a level where the component needs to be intensively cooled, or otherwise it will become overheated. This paper presents the cooling of microelectronic components using microjets.
Źródło:
Archives of Thermodynamics; 2015, 36, 3; 139-147
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of the use of adsorption processes in trigeneration systems
Autorzy:
Grzebielec, A.
Rusowicz, A.
Powiązania:
https://bibliotekanauki.pl/articles/240946.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
adsorption refrigeration
trigeneration
sorption
chiller
absorpcja
chłodzenie
trójgeneracja
sorpcja
agregat
Opis:
The trigeneration systems for production of cold use sorption refrigeration machines: absorption and adsorption types. Absorption systems are characterized namely by better cooling coefficient of performance, while the adsorptive systems are characterized by the ability to operate at lower temperatures. The driving heat source temperature can be as low as 60-70˚C. Such temperature of the driving heat source allows to use them in district heating systems. The article focuses on the presentation of the research results on the adsorption devices designed to work in trigeneration systems.
Źródło:
Archives of Thermodynamics; 2013, 34, 4; 35-49
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermodynamic analysis of a new dual evaporator CO2 transcritical refrigeration cycle
Autorzy:
Abdellaoui, E. Y.
Kairouani, L. K.
Powiązania:
https://bibliotekanauki.pl/articles/240198.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
CO2
energy
refrigeration
ejector
exergy
energia
chłodzenie
ejektor
egzergia
Opis:
In this work, a new dual-evaporator CO2 transcritical refrigeration cycle with two ejectors is proposed. In this new system, we proposed to recover the lost energy of condensation coming off the gas cooler and operate the refrigeration cycle ejector free and enhance the system performance and obtain dual-temperature refrigeration simultaneously. The effects of some key parameters on the thermodynamic performance of the modified cycle are theoretically investigated based on energetic and exergetic analysis. The simulation results for the modified cycle indicate more effective system performance improvement than the single ejector in the CO2 vapor compression cycle using ejector as an expander ranging up to 46%. The exergetic analysis for this system is made. The performance characteristics of the proposed cycle show its promise in dual-evaporator refrigeration system.
Źródło:
Archives of Thermodynamics; 2017, 38, 1; 39-62
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Possibility of using adsorption refrigeration unit in district heating network
Autorzy:
Grzebielec, A.
Rusowicz, A.
Jaworski, M.
Laskowski, R.
Powiązania:
https://bibliotekanauki.pl/articles/240811.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
refrigeration
adsorption refrigeration
air conditioning
district heating network
chłodzenie
absorpcja
klimatyzacja
sieć ciepłownicza
Opis:
Adsorption refrigeration systems are able to work with heat sources of temperature starting with 50°C. The aim of the article is to determine whether in terms of technical and economic issues adsorption refrigeration equipment can work as elements that produce cold using hot water from the district heating network. For this purpose, examined was the work of the adsorption air conditioning equipment cooperating with drycooler, and the opportunities offered by the district heating network in Warsaw during the summer. It turns out that the efficiency of the adsorption device from the economic perspective is not sufficient for production of cold even during the transitional period. The main problem is not the low temperature of the water supply, but the large difference between the coefficients of performance, COPs, of adsorption device and a traditional compressor air conditioning unit. When outside air temperature is 25°C, the COP of the compressor type reaches a value of 4.49, whereas that of the adsorption device in the same conditions is 0.14. The ratio of the COPs is 32. At the same time ratio between the price of 1 kWh of electric power and 1 kWh of heat is only 2.85. Adsorption refrigeration equipment to be able to compete with compressor devices, should feature COPads efficiency to be greater than 1.52. At such a low driving temperature and even changing the drycooler into the evaporative cooler it is not currently possible to achieve.
Źródło:
Archives of Thermodynamics; 2015, 36, 3; 15-24
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental investigation of the ecological hybrid refrigeration cycle
Autorzy:
Cyklis, P.
Kantor, R.
Ryncarz, T.
Górski, B.
Duda, R.
Powiązania:
https://bibliotekanauki.pl/articles/240899.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hybrid refrigerating cycle
adsorption
two stage refrigerating
hybrydowy cykl chłodniczy
adsorpcja
dwustopniowe chłodzenie
Opis:
The requirements for environmentally friendly refrigerants promote application of CO2 and water as working fluids. However there are two problems related to that, namely high temperature limit for CO2 in condenser due to the low critical temperature, and low temperature limit for water being the result of high triple point temperature. This can be avoided by application of the hybrid adsorption-compression system, where water is the working fluid in the adsorption high temperature cycle used to cool down the CO2 compression cycle condenser. The adsorption process is powered with a low temperature renewable heat source as solar collectors or other waste heat source. The refrigeration system integrating adsorption and compression system has been designed and constructed in the Laboratory of Thermodynamics and Thermal Machine Measurements of Cracow University of Technology. The heat source for adsorption system consists of 16 tube tulbular collectors. The CO2 compression low temperature cycle is based on two parallel compressors with frequency inverter. Energy efficiency and TEWI of this hybrid system is quite promising in comparison with the compression only systems.
Źródło:
Archives of Thermodynamics; 2014, 35, 3; 145-154
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of a two-phase thermosyphon loop with minichannels and a minipump in computer cooling
Autorzy:
Bieliński, H.
Mikielewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/240132.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
thermosyphon loop
two phase flow
computer cooling
obieg termosyfonowy
przepływ dwufazowy
chłodzenie komputera
Opis:
This paper focuses on the computer cooling capacity using the thermosyphon loop with minichannels and minipump. The one-dimensional separate model of two-phase flow and heat transfer in a closed thermosyphon loop with minichannels and minipump has been used in calculations. The latest correlations for minichannels available in literature have been applied. This model is based on mass, momentum, and energy balances in the evaporator, rising tube, condenser and the falling tube. A numerical analysis of the mass flux and heat transfer coefficient in the steady state has been presented.
Źródło:
Archives of Thermodynamics; 2016, 37, 1; 3-16
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling of a micro-channel heat sink for cooling of high-power laser diode arrays
Autorzy:
Furmański, P.
Thualfaqir, K.
Łapka, P.
Powiązania:
https://bibliotekanauki.pl/articles/240825.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
micro heat sink
laser diode arrays cooling
numerical simulation
chłodzenie
laser
dioda
radiator
modelowanie numeryczne
Opis:
Micro-channel heat sinks are used in a wide variety of applications, including microelectronic devices, computers and high-energy-laser mirrors. Due to the high power density that is encountered in these devices (the density of delivered electrical power up to a few kW/cm2 ) they require efficient cooling as their temperatures must generally not exceed 100 °C. In the paper a new design for micro-channel heat sink (MCHS) to be used for cooling laser diode arrays (LDA) is considered. It is made from copper and consisting of 37 micro-channels with length of 9.78 mm, width of 190 µm and depth of 180 µm with the deionized water as a cooling medium. Mathematical and numerical models of the proposed design of the heat sink were developed. A series of thermofluid numerical simulations were performed for various volumetric flow rates of the cooling medium, its inlet temperature and different thermal power released in the laser diode. The results show that the LDA temperature could be decreased from 14 to 17% in comparison with earlier proposed design of the heat sink with the further drop in temperature obtained by applying indium instead of gallium arsenide as the soldering material between the LDA and MCHS interface. Moreover, it was found that the maximum temperature, and therefore the thermal resistance of the considered heat sink, could be decreased by increasing the coolant flow rate.
Źródło:
Archives of Thermodynamics; 2018, 39, 3; 15-27
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Heat transfer during condensation of refrigerants in tubular minichannels
Autorzy:
Bohdal, T.
Charun, H.
Sikora, M.
Powiązania:
https://bibliotekanauki.pl/articles/239949.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chłodzenie
kompaktowy kondensator
kondensacja w minikanałach
wymiana ciepła
compact condenser
condensation in minichannels
heat transfer
refrigeration
Opis:
Abstract The present paper describes the results of experimental investigations of heat transfer during condensation of R134a, R404A and R407C in pipe minichannels with internal diameters 0.31-3.30 mm. The results concern investigations of the local heat transfer coefficient. The results were compared with the correlations proposed by other authors. Within the range of examined parameters of the condensation process in minichannels made of stainless steel, it was established that the values of the heat transfer coefficient may be described with Akers et al., Mikielewicz and Shah correlations within a limited range of the mass flux density of the refrigerant and the minichannel diameter. On the basis of experimental investigations, the authors proposed their own correlation for the calculation of local heat transfer coefficient.
Źródło:
Archives of Thermodynamics; 2012, 33, 2; 3-22
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Temperature moderation in a multistorey building by melting of a phase-change material
Autorzy:
Dubovsky, V.
Ziskind, G.
Letan, R.
Powiązania:
https://bibliotekanauki.pl/articles/240188.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
wax melting
room cooling at ceiling
numerical simulations
thermal comfort
topienie
wosk
chłodzenie
symulacja numeryczna
komfort cieplny
Opis:
The current numerical study focuses on the feasibility of furnishing thermal comfort in a structure, by using paraffin wax stored on a plate below the ceiling in a multi-storey building. The method is aimed to reduce energy demands at the increasing thermal loads. In summer, in daytime, walls of the building are exposed to the ambient thermal load, and heat transferred inside is absorbed by the melting wax. The study is numerical. It relates to temperature variations outside and inside, coupled with heat conduction and accumulation in walls, with radiation between the surfaces, with natural convection of air inside and melting of the wax at the ceiling. Fins spacing on the storage plate, visualization of the melting process, and its parametric investigation provide an insight into the physical phenomena. Temperature and flow fields were investigated for 3 mm and 12 mm thick layers of wax. At the specified conditions of the present study a 3 mm layer provides thermal comfort for most of the day, while a 6 mm layer may suffice for the entire day. Fluent 6.3 software was used in the computations.
Źródło:
Archives of Thermodynamics; 2013, 34, 1; 85-101
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Method of high heat flux removal by usage of liquid spray cooling
Autorzy:
Smakulski, P.
Powiązania:
https://bibliotekanauki.pl/articles/239973.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
critical heat flux
spray cooling
two-phase heat transfer
numerical simulation
krytyczny strumień ciepła
chłodzenie natryskowe
wymiana ciepła
symulacja numeryczna
Opis:
High heat flux removal are important issue in many perspective applications such as computer chips, laser diode arrays, or boilers working on supercritical parameters. Electronic microchips constructed nowadays are model example of high heat flux removal, where the cooling system have to maintain the temperature below 358 K and take heat flux up to 300 W/cm2. One of the most efficient methods of microchips cooling turns out to be the spray cooling method. Review of installations has been accomplished for removal at high heat flux with liquid sprays. In the article are shown high flux removal characteristic and dependences, boiling critical parameters, as also the numerical method of spray cooling analysis.
Źródło:
Archives of Thermodynamics; 2013, 34, 3; 173-184
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-11 z 11

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies