Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Lee, K. J." wg kryterium: Autor

  Lista filtrów
Wyrównaj
Wyświetlanie 1-15 z 34
Tytuł:
Properties of Copper Doped Neodymium Nickelate Oxide as Cathode Material for Solid Oxide Fuel Cells
Autorzy:
Lee, K. J.
Choe, Y-J.
Hwang, H-J.
Powiązania:
https://bibliotekanauki.pl/articles/351292.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
solid oxide fuel cells
copper
electrical conductivity
excess oxygen
Opis:
Mixed ionic and electronic conducting K2NiF4-type oxide, Nd2Ni1-xCuxO4+δ (x=0~1) powders were synthesized by solid state reaction technique and solid oxide fuel cells consisting of a Nd2Ni1-xCuxO4+δ cathode, a Ni-YSZ anode and ScSZ as an electrolyte were fabricated. The effect of copper substitution for nickel on the electrical and electrochemical properties was examined. Small amount of copper doping (x=0.2) resulted in the increased electrical conductivity and decreased polarization resistance. It appears that this phenomenon was associated with the high mean valence of nickel and copper and the resulting excess oxygen (δ). It was found that power densities of the cell with the Nd2Ni1-xCuxO4+δ (x=0.1 and 0.2) cathode were higher than that of the cell with theNd2NiO4+δ cathode.
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 2A; 625-628
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cr Poisoning On Nd2Ni0.95Cu0.05O4+δ Cathode for Solid Oxide Fuel Cells
Autorzy:
Choe, Y-J.
Lee, K. J.
Hwang, H-J.
Powiązania:
https://bibliotekanauki.pl/articles/354728.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
chromium poisoning
Ruddlesden-Popper
layered perovskite
solid oxide fuel cells
Nd2NiO4
Opis:
In this study, Nd2Ni1-xCuxO4+δ (x=0, 0.05, 0.1, and 0.2) layered perovskite powders were synthesized by the glycine nitrate process (GNP) and the chromium poisoning effect on the electrochemical performance of the Nd2Ni0.95Cu0.05O4+δ and La0.6Sr0.4Co0.2Fe0.88O3-δ cathodes were investigated. In the case of the LSCF cathode, the strontium chromite phase formed after the exposure of the gaseous chromium species, while there was no additional phase in the Nd2Ni0.95Cu0.05O4+δ cathode. The area specific resistance (ASR) of the Nd2Ni0.95Cu0.05O4+δ cathode did not change significantly after the exposure of the gaseous chromium species at 800°C
Źródło:
Archives of Metallurgy and Materials; 2016, 61, 2A; 629-634
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Aluminum Oxide Formation On Fecral Catalyst Support By Electro-Chemical Coating
Powstawanie tlenku glinu na nośniku katalizatora FeCrAl przez osadzanie elektrochemiczne
Autorzy:
Yang, H. S.
Jang, D. H.
Lee, K. J.
Powiązania:
https://bibliotekanauki.pl/articles/355942.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
FeCrAl
catalyst support
aluminum oxide formation
PEO
plasma electrolytic oxidation
electrochemical coating
nośnik katalizatora
tlenek glinu
plazmowe utlenianie elektrolityczne
elektrochemiczne osadzanie
Opis:
FeCrAl is comprised essentially of Fe, Cr, Al and generally considered as metallic substrates for catalyst support because of its advantage in the high-temperature corrosion resistance, high mechanical strength, and ductility. Oxidation film and its adhesion on FeCrAl surface with aluminum are important for catalyst life. Therefore various appropriate surface treatments such as thermal oxidation, Sol, PVD, CVD has studied. In this research, PEO (plasma electrolytic oxidation) process was applied to form the aluminum oxide on FeCrAl surface, and the formed oxide particle according to process conditions such as electric energy and oxidation time were investigated. Microstructure and aluminum oxide particle on FeCrAl surface after PEO process was observed by FE-SEM and EDS with element mapping analysis. The study presents possibility of aluminum oxide formation by electro-chemical coating process without any pretreatment of FeCrAl.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1503-1506
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Rapid Synthesis of Gold Nano-Particles Using Pulse Waved Potential in a Non-Aqueous Electrolyte
Autorzy:
Jang, J. G.
Lee, J.-O.
Lee, C. K.
Powiązania:
https://bibliotekanauki.pl/articles/352529.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
gold
nanoparticle
nonaqueous electrolyte
pulse wave
catalyst
Opis:
Rapid synthesis of gold nanoparticles (AuNPs) by pulsed electrodeposition was investigated in the non-aqueous electrolyte, 1-ethyl-3-methyl-imidazoliumbis(trifluoro- methanesulfonyl)imide ([EMIM]TFSI) with gold trichloride (AuCl3). To aid the dissolution of AuCl3, 1-ethyl-3-methyl-imidazolium chloride ([EMIM]Cl) was used as a supporting electrolyte in [EMIM]TFSI. Cyclicvoltammetry experiments revealed a cathodic reaction corresponding to the reduction of gold at −0.4 V vs. Pt-QRE. To confirmthe electrodeposition process, potentiostatic electrodeposition of gold in the non-aqueous electrolyte was conducted at −0.4 V for 1 h at room temperature. To synthesize AuNPs, pulsed electrodeposition was conducted with controlled duty factor, pulse duration, and overpotential. The composition, particle-size distribution, and morphology of the AuNPs were confirmed by field-emission scanning electron microscopy (FE-SEM), energy-dispersive spectroscopy (EDS), and transmission electron microscopy (TEM). The electrodeposited AuNPs were uniformly distributed on the platinum electrode surface without any impurities arising from the non-aqueous electrolyte. The size distribution of AuNPs could be also controlled by the electrodeposition conditions.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1389-1392
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Compressive Deformation Behavior of Thick Micro-Alloyed HSLA Steel Plates at Elevated Temperatures
Autorzy:
Lee, J.-H.
Kim, D.-O.
Lee, K.
Powiązania:
https://bibliotekanauki.pl/articles/351774.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
alloys
rolling
strain rate
compression test
HSLA steel
Opis:
The hot deformation behavior of a heavy micro-alloyed high-strength low-alloy (HSLA) steel plate was studied by performing compression tests at elevated temperatures. The hot compression tests were carried out at temperatures from 923 K to 1,223 K with strain rates of 0.002 s-1 and 1.0 s-1. A long plateau region appeared for the 0.002 s-1 strain rate, and this was found to be an effect of the balancing between softening and hardening during deformation. For the 1.0 s-1 strain rate, the flow stress gradually increased after the yield point. The temperature and the strain rate-dependent parameters, such as the strain hardening coefficient (n), strength constant (K), and activation energy (Q), obtained from the flow stress curves were applied to the power law of plastic deformation. The constitutive model for flow stress can be expressed as σ = (39.8 ln (Z) – 716.6) · ε(−0.00955ln(Z) + 0.4930) for the 1.0 s-1 strain rate and σ = (19.9ln (Z) – 592.3) · ε(−0.00212ln(Z) + 0.1540) for the 0.002 s-1 strain rate.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1191-1196
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Pre-Sintering on the Diffusion Treatment of HRE for Coercivity Enhancement of a NdFeB Sintered Magnet
Autorzy:
Lee, M. W.
Lee, J. K.
Jang, T. S.
Powiązania:
https://bibliotekanauki.pl/articles/355250.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
grain boundary diffusion process
GBDP
NdFeB magnet
coercivity
pre-sintering
Opis:
We investigated the effect of pre-sintering process on the penetration behavior of Dy in a NdFeB sintered magnet which was grain boundary diffusion treated with Cu/Al mixed Dy source. The pre-sintering of a magnet was performed at 900°C in vacuum and then the pre-sintered body was dipped in the solutions of DyH2, DyH2 + Cu, and DyH2 + Al, respectively. The dipped pre-sintered body were then fully sintered 4 hours at 1060°C followed by a subsequent annealing. The pre-sintering apparently improved the diffusivity of Dy atoms. The penetration of Dy into the magnet extended almost to 2,000 μm from the surface, about four times deeper than that of the normally sintered and diffusion treated one, when the DyH2 + Al solution was used as a Dy source. However, the resulting increase of coercivity was about 4 kOe, somewhat lower than that of the normally treated one, mostly due to excessive oxide formation that hindered to make a continuous Nd-rich grain boundary phase and a core-shell type structure.
Źródło:
Archives of Metallurgy and Materials; 2019, 64, 2; 597-601
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Study On Dispersion Stability Of Nickel Nanoparticles Synthesized By Wire Explosion In Liquid Media
Badanie stabilności dyspersji nanocząstek niklu wytworzonych metodą WEP w ciekłym medium
Autorzy:
Kim, C. K.
Lee, G.-J.
Lee, M. K.
Rhee, C. K.
Powiązania:
https://bibliotekanauki.pl/articles/356909.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nickel nanofluid
pulsed wire evaporation
surfactant
zeta potential
dispersion stability
nanocząstka niklu
środek powierzchniowo czynny
stabilność dyspersji
potencjał zeta
dyspersja
Opis:
In this study, nickel nanoparticles were synthesized in ethanol using portable pulsed wire evaporation, which is a one-step physical method. From transmission electron microscopy images, it was found that the Ni nanoparticles exhibited a spherical shape with an average diameter of 7.3 nm. To prevent aggregation of the nickel nanoparticles, a polymer surfactant was added into the ethanol before the synthesis of nickel nanoparticles, and adsorbed on the freshly synthesized nickel nanoparticles during the wire explosion. The dispersion stability of the prepared nickel nanofluids was investigated by zeta-potential analyzer and Turbiscan optical analyzer. As a result, the optimum concentration of polymer surfactant to be added was suggested for the maximized dispersion stability of the nickel nanofluids.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1379-1382
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of PVA Polymer Type and Calcination Temperature on Synthesis of Nanocrystalline Yttria Powder by Polymer Solution Route
Autorzy:
Yang, Y.-K.
Lee, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/356024.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
yttria
PVA
nanocrystalline
synthesis
nanowire
Opis:
Nano-sized yttria (Y2O3) powders were synthesized by a polymer solution route using polyvinyl alcohol (PVA) as an organic carrier. The PVA polymer affected the dispersion of yttrium ions in precursor sol. In this study, three kinds of PVA polymer (different molecular weight) were applied for synthesis of yttria powder. The PVA type as well as calcination temperature had a strongly influence on the particle morphology. Single crystal nano wire particles were observed at the temperature of polymer burn out range and the size was dependent on the PVA type. The stable, fully crystallized yttria powder was obtained through the calcination at 800°C for 1 h. The yttria powder prepared with the high weight PVA (MW: 153,000) revealed a particle size of 30 nm with a surface area of 18.8 m2/g.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1473-1476
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Crystallization Behavior of Zr62Al8Ni13Cu17 Metallic Glass
Autorzy:
Jo, M. S.
Lee, J. K.
Powiązania:
https://bibliotekanauki.pl/articles/353070.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
metallic glass
crystallization
kinetics
amorphous
Zr-based
Opis:
The crystallization behavior has been studied in Zr62Al8Ni13Cu17 metallic glass alloy. The Zr62Al8Ni13Cu17 metallic glass crystallized through two steps. The fcc Zr2Ni phase transformed from the amorphous matrix during first crystallization and then the Zr2Ni and residual amorphous matrix transformed into a mixture of tetragonal Zr2Cu and hexagonal Zr6Al2Ni phases. Johnson- Mehl-Avrami analysis of isothermal transformation data suggested that the formation of crystalline phase is primary crystallization by diffusion-controlled growth.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1023-1026
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Enhanced Microwave Absorption of CNT Composites Mixing with Fe3O4 and Carbonyl Iron
Autorzy:
Park, J. H.
Choi, J.
Lee, K.
Park, J.
Song, J. K.
Jeon, E.
Powiązania:
https://bibliotekanauki.pl/articles/351106.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnetic powders
complex permittivity
complex permeability
composite materials
microwave absorption
Opis:
We fabricated two different kinds of composite materials for absorbing microwave in a frequency range of 2 to 18 GHz using coaxial airline and thru-reflect-line (TRL) method. The composite materials having carbon nanotube (CNT) with carbonyl iron (CI) or iron oxide (Fe3 O4 ) were fabricated by mixing each components. Magnetic properties were measured by SQUID equipment. Complex permittivity and complex permeability were also obtained by measuring S-parameters of the toroidal specimen dispersing CI/CNT and Fe3 O4 /CNT into the 50 weight percent (wt%) epoxy resin. The real permittivity was improved by mixing the CNT however, the real permeability was same as pure magnetic powders. The CI/CNT had a maximum value of real permittivity and real permeability, 11 and 1.4 at 10 GHz, respectively. The CNT composites can be adapted to the radar absorbing materials, band width 8-12 GHz.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1513-1516
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Heat Treatment on the Microstructure and Tensile Deformation Behavior of Oxide Dispersion Strengthened Alloys Manufactured by Complex Milling Process
Autorzy:
Kim, Y.-K.
Kim, J.-H.
Gwon, J.-H.
Lee, K.-A.
Powiązania:
https://bibliotekanauki.pl/articles/352535.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ball milling
oxide dispersion strengthening
microstructure
tensile deformation behavior
Opis:
This study attempted to manufacture an ODS alloy by combining multiple milling processes in mechanical alloying stage to achieve high strength and fracture elongation. The complex milling process of this study conducted planetary ball milling, cryogenic ball milling and drum ball milling in sequential order, and then the microstructure and tensile deformation behavior were investigated after additional heat treatment. The oxide particles distributed within the microstructure were fine oxide particles of 5~20 nm and coarse oxide particles of 100~200 nm, and the oxide particles were confirmed to be composed of Cr, Ti, Y and O. Results of tensile tests at room temperature measured yield strength, tensile strength and elongation as 1320 MPa, 2245 MPa and 4.2%, respectively, before heat treatment, and 1161 MPa, 2020 MPa and 5.5% after heat treatment. This results indicate that the ODS alloy of this study gained very high strengths compared to other known ODS alloys, allowing greater plastic zones.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1335-1340
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Atomistic Analysis Of Radiation-Induced Segregation In Ion-Irradiated Stainless Steel 316
Analiza w skali atomowej indukowanej promieniowaniem segregacji w stali nierdzewnej 316
Autorzy:
Lee, G.-G.
Jin, H.-H.
Chang, K.
Lee, B. H.
Kwon, J.
Powiązania:
https://bibliotekanauki.pl/articles/354713.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
atom probe tomography (APT)
radiation-induced segregation (RIS)
ion irradiation
irradiation defects
stainless steel
APT
RIS
stal nierdzewna
segregacja
Opis:
Stainless steel (SS) is a well-known material for the internal parts of nuclear power plants. It is known that these alloys exhibit radiation-induced segregation (RIS) at point defect sinks at moderate temperature, while in service. The RIS behavior of SS can be a potential problem by increasing the susceptibility to irradiation-assisted stress corrosion cracking. In this work, the RIS behavior of solute atoms at sinks in SS 316 irradiated with Fe4+ ions were characterized by atom probe tomography (APT). There were torus-shaped defects along with a depletion of Cr and enrichment of Ni and Si. These clusters are believed to be dislocation loops resulting from irradiation. The segregation of solutes was also observed for various defect shapes. These observations are consistent with other APT results from the literature. The composition of the clusters was analyzed quantitatively almost at the atomic scale. Despite the limitations of the experiments, the APT analysis was well suited for discovering the structure of irradiation defects and performing a quantitative analysis of RIS in irradiated specimens.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1179-1184
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Manufacturing And High Temperature Oxidation Properties Of Electro-Sprayed Fe-24.5% Cr-5%Al Powder Porous Metal
Wytwarzanie i wysokotemperaturowe utlenianie elektro-rozpylanego porowatego proszku Fe-24.5% Cr-5%Al
Autorzy:
Lee, K-A.
Oh, J-S.
Kong, Y-M.
Kim, B-K.
Powiązania:
https://bibliotekanauki.pl/articles/350912.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
powder porous metal
electro-spray process
electric wire explosion
Fe-24Cr-5Al
high temperature oxidation
porowaty proszek metalu
elektrorozpylanie
utlenianie wysokotemperaturowe
Opis:
Fe-Cr-Al based Powder porous metals were manufactured using a new electro-spray process, and the microstructures and high-temperature oxidation properties were examined. The porous materials were obtained at different sintering temperatures (1350°C, 1400°C, 1450°C, and 1500°C and with different pore sizes (500 μm, 450 μm, and 200 μm). High-temperature oxidation experiments (TGA, Thermal Gravimetry Analysis) were conducted for 24 hours at 1000°C in a 79% N2+ 21% O2, 100 mL/min. atmosphere. The Fe-Cr-Al powder porous metals manufactured through the electro-spray process showed more-excellent oxidation resistance as sintering temperature and pore size increased. In addition, the fact that the densities and surface areas of the abovementioned powder porous metals had the largest effects on the metal’s oxidation properties could be identified.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1169-1173
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and Magnetic Properties of NdFeB Sintered Magnets Diffusion-Treated with Cu/Al Mixed Dyco Alloy-Powder
Autorzy:
Lee, M.-W.
Bae, K.-H.
Lee, S.-R.
Kim, H.-J.
Jang, T.-S.
Powiązania:
https://bibliotekanauki.pl/articles/353351.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nd-Fe-B sintered magnets
grain boundary diffusion process
low melting point element
DyCo alloy-powder diffusion
Opis:
We investigated the microstructural and magnetic property changes of DyCo, Cu + DyCo, and Al + DyCo diffusion-treated NdFeB sintered magnets. The coercivity of all diffusion treated magnet was increased at 880ºC of 1st post annealing(PA), by 6.1 kOe in Cu and 7.0 kOe in Al mixed DyCo coated magnets, whereas this increment was found to be relatively low (3.9 kOe) in the magnet coated with DyCo only. The diffusivity and diffusion depth of Dy were increased in those magnets which were treated with Cu or Al mixed DyCo, mainly due to comparatively easy diffusion path provided by Cu and Al because of their solubility with Ndrich grain boundary phase. The formation of Cu/Al-rich grain boundary phase might have enhanced the diffusivity of Dy-atoms. Moreover, relatively a large number of Dy atoms reached into the magnet and mostly segregated at the interface of Nd2 Fe14 B and grain boundary phases covering Nd2 Fe14 B grains so that the core-shell type structures were developed. The formation of highly anisotropic (Nd, Dy)2Fe14B phase layer, which acted as the shell in the core-shell type structure so as to prevent the reverse domain movement, was the cause of enhancing the coercivity of diffusion treated NdFeB magnets. Segregation of cobalt in Nd-rich TJP followed by the formation of Co-rich phase was beneficial for the coercivity enhancement, resulting in the stabilization of the metastable c-Nd2O3 phase.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1263-1266
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High-temperature Oxidation Behavior and Kinetics of Forged 12Cr-MoVW Steel
Autorzy:
Kim, Y. H.
Oak, J.-J.
Bae, K.-C.
Lee, W-J.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/351450.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ferritic/martensitic stainless steels
forging
oxidation kinetics
oxide layer
Opis:
The oxidation kinetics of forged 12Cr-MoVW steel was investigated in an air (N2+O2) atmosphere at 873-1073 K (Δ50 K) using thermogravimetric analysis. The oxidized samples were characterized using X-ray diffraction, and the surface and cross-sectional morphologies were examined using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The forged 12Cr-MoVW steel samples exhibited parabolic behavior and a low oxidation rate compared with their as-cast counterparts. A protective oxide layer was uniformly formed at relatively low temperature (≤973 K) for the forged samples, which thus exhibited better oxidation resistance than the as-cast ones. These oxides are considered solid-solution compounds such as (Fe, Cr)2O3.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1099-1104
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Wyświetlanie 1-15 z 34

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies