Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Kim, C.-J." wg kryterium: Autor


Tytuł:
Novel Extraction Process Of Rare Earth Elements From NdFeB Powders Via Alkaline Treatment
Nowy sposób ekstrakcji pierwiastków ziem rzadkich z proszków NdFeB w roztworach alkalicznych
Autorzy:
Chung, K. W.
Kim, C.-J.
Yoon, H.-S.
Powiązania:
https://bibliotekanauki.pl/articles/355324.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
recycling
NdFeB magnet
alkaline treatment
leaching
selective leaching efficiency
recykling
magnes neodymowy
obróbka alkaliczna
ługowanie
wydajność
Opis:
The alkaline treatment of NdFeB powders in NaOH solution at various equivalent amounts of NaOH at 100°C was performed. The resultant powders were then leached in 0.5M H2SO4 solution at 25°C for 2 minutes. At 5 equivalents of NaOH, neodymium in NdFeB powders was partially transformed to neodymium hydroxide. The transformation of neodymium to neodymium hydroxide actually occurred at 10 equivalents of NaOH and was facilitated by increasing the equivalent of NaOH from 10 to 30. In addition, iron was partially transformed to magnetite during the alkaline treatment, which was also promoted at a higher equivalent of NaOH. The leaching yield of neodymium from alkaline-treated powders was increased with an increasing equivalent of NaOH up to 10; however, it slightly decreased with the equivalent NaOH of over 10. The leaching yield of iron was inversely proportional to that of rare earth elements. NdFeB powders treated at 10 equivalents of NaOH showed a maximum leaching yield of neodymium and dysprosium of 91.6% and 94.6%, respectively, and the lowest leaching yield of iron of 24.2%, resulting in the highest selective leaching efficiency of 69.4%.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1301-1305
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Formation of Different Cu Nanopowders and Stability of Cu Fluids Produced by Electrical Explosion of Wire in Liquid
Autorzy:
Nguyen, M.-T.
Kim, J.-H.
Kim, J.-C.
Powiązania:
https://bibliotekanauki.pl/articles/355217.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Cu nanopowder
Cu nanofluids
electrical explosion of wire
stability of nanofluids
Opis:
In this study, copper nanoparticles and nanofluids were synthesized by electrical explosion of wire (EEW) in liquid media such as water, ethanol, and acetone. The effect of the different conditions on the properties of the as-synthesized Cu powders and nanofluids were investigated. X-ray diffraction (XRD) analysis was employed to measure the phase of the as-synthesized powder. Only pure Cu phase appeared in case of acetone condition, but CuO and CuO2 phases could be observed in the others. The EEWed particle size was broadened from under 50 to 100 nm. The results showed that acetone was the best condition for achieving smaller particles, preventing the oxidation of the Cu particles and good stability of the nanofluids.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1453-1457
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental Study On Fracture Property Of Tapered Double Cantilever Beam Specimen With Aluminum Foam
Doświadczalne badanie pękania mimośrodowo rozciąganej zwężanej próbki z bocznym karbem wykonanej z piany aluminiowej
Autorzy:
Kim, Y. C.
Kim, S. S.
Cho, J. U.
Powiązania:
https://bibliotekanauki.pl/articles/352697.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminum foam
tapered double cantilever beam (TDCB)
fracture behavior
adhesively bonded structures
adhesive fracture energy
piana aluminiowa
pękanie
stożkowa podwójna belka wspornikowa
struktura sklejona
Opis:
It is indispensable to evaluate fracture energy as the bonding strength of adhesive at composite material with aluminum foam. This specimen is designed with tapered double cantilever beam by British standards (BS 7991 and ISO 11343). 4 kinds of specimens due to m values of 2, 2.5, 3 and 3.5 are manufactured and compared each other with the experimental results. Adhesive fracture energy is calculated from the formulae of British standards. The value of m is the gradient which is denoted as the length and the height of specimen. As m becomes greater at static experimental result, the maximum load becomes higher and the displacement becomes lower. And the critical fracture energy becomes higher. As m becomes less at fatigue experimental result, the displacement becomes higher and the critical fracture energy becomes higher. Fracture behavior of adhesive can be analyzed by this study and these experimental results can be applied into real field effectively. The stability on TDCB structure bonded with aluminum foam composite can be predicted by use of this experimental result. Adhesive fracture energy is calculated from the formulae of British standards. Based on correlations obtained in this study, the fracture behavior of bonded material would possibly be analyzed and aluminum foam material bonded with adhesive would be applied to a composite structure in various fields, thereby analyzing the mechanical and fracture characteristic of the material.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1459-1462
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on Effects of Mold Temperature on the Injection Molded Article
Autorzy:
Han, J.-H.
Kim, Y.-C.
Powiązania:
https://bibliotekanauki.pl/articles/351919.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
injection molding
mold temperature
cooling temperature
molded article
Opis:
This is a study of the effects of temperature of injection mold on the injection molded article. By supplying water of the proper temperature in the cooling line of mold in the cooling process, the mold was the appropriate temperature, and the deformation of the injection molded article was examined according to the mold temperature. In this study, we conducted simulation analysis and experiments, and the results were analyzed. The minimum deformation of the injection molded article model obtained by supplying 50°C water in the cooling line is 0.003 mm, and the maximum deformation was 0.813 mm. Injection molded article models obtained by supplying 20°C water were found to be a minimum of 0.002 mm, with deformation of up to 0.761 mm. When comparing both conditions, the error rate of injection molded article obtained by supplying 20°C water in the mold cooling line was lower by about 0.18%.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1271-1274
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication and Characterization of Ni-CNT Composites by Electrical Explosion of Wire in Different Liquids
Autorzy:
Thuyet-Nguyen, M.
Maithili-Biswas, Maithili-Biswas
Kim, W. J.
Kim, J.-C.
Powiązania:
https://bibliotekanauki.pl/articles/958201.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Nickel-Carbon nanotubes composite
carbon nanotubes
electrical explosion of wire
nano-colloid
magnetic properties
Opis:
In this study, Ni-CNT powders and colloids were synthesized via the Electrical explosion of wire (EEW) in different liquid conditions. The influence of ambient solvents (D.I. Water, ethanol, methanol, acetone and ethylene-glycol) on characteristics of the as-synthesized Ni-CNT was investigated. The morphology and size were observed by field emission scanning electron microscopy (FE-SEM). The Ni particles were spherical or near spherical shape. The phase of the composite powders analyzed via X-ray diffraction demonstrate the presence of CNTs in composite powders is not affect the structure of Ni. However, the phase of the composites was changed based on the changing of liquid conditions. Stability of colloids was investigated by Turbiscan technique. Magnetic properties were also investigated by Vibrating sample magnetometer (VSM) at room temperature. The as-synthesized composite powders revealed a ferromagnetic characteristic material.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1219-1223
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Sintering and Microstructures of SUS 316L Powder Produced by 3D Printing Process
Autorzy:
Kim, W. J.
Nguyen, H.-H.
Kim, H. Y.
Nguyen, M.-T.
Park, H. S.
Kim, J.-C.
Powiązania:
https://bibliotekanauki.pl/articles/356018.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stainless steel
3D printing
selective laser sintering
SUS 316L
flake powder
Opis:
Selective laser sintering (SLS) is a type of laminating sintering technique, using CO2 laser with (metal, polymer, and ceramic) powders. In this result, the flake SUS 316L was used to achieve a high porous product, and compare to spherical type. After SLS, the porosity of flake-type sample with 34% was quite higher than that of the spherical-type one that had only 11%. The surface roughness of the flake SLS sample were also investigated in both inner and surface parts. The results show that the deviation of the roughness of the surface part is about 64.40μm, while that of the internal one was about 117.65μm, which presents the containing of high porosity in the uneven surfaces. With the process using spherical powder, the sample was quite dense, however, some initial particles still remained as a result of less energy received at the beneath of the processing layer.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1215-1218
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Preparation of Nickel Powders by Reduction of Nickel Hydroxide Using the Taylor Fluid Flow
Autorzy:
Park, I.-J.
Kim, D.-W.
Kim, G.-H.
Chae, H.-J.
Jung, H.-C.
Powiązania:
https://bibliotekanauki.pl/articles/355021.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ni(OH)2
nickel
Taylor fluid flow
fine powder
Opis:
In this study, Ni(OH)2 was synthesized by the continuous reaction by the Taylor fluid flow and compared with those prepared from the conventional batch type reaction. The nickel powders were synthesized by reduction of Ni(OH)2 in an aqueous solution with hydrazine hydrate acting as the reductant. And then the characteristics of the nickel powder according to the synthesis method were compared. The average particle size of the synthesized Ni(OH)2 using Taylor reactor was generally decreased about 1.5~2.5 times more than the batch reaction. The nickel powders prepared by the batch reaction highly agglomerated with non-uniform particles. In the Taylor reaction, the agglomeration of particles was broken and uniform nickel powder was produced.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 3; 1443-1447
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental Study On Fracture Property Of Double Cantilever Beam Specimen With Aluminum Foam
Doświadczalne badanie pękania mimośrodowo rozciąganej próbki z bocznym karbem wykonanej z piany aluminiowej
Autorzy:
Kim, Y. C.
Choi, H. K.
Cho, J. U.
Powiązania:
https://bibliotekanauki.pl/articles/351465.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
aluminium foam
double cantilever beam
fracture energy
adhesively bonded structure
piana aluminiowa
podwójna belka wspornikowa
energia pękania
Opis:
This study aims to investigate double cantilever beam specimen with aluminum foam bonded by spray adhesive to investigate the fracture strength of the adhesive joint experimentally. The fracture energy at opening mode is calculated by the formulae of British Engineering Standard (BS 7991) and International Standard (ISO 11343). For the static experiment, four types of specimens with the heights (h) of 25 mm, 30 mm, 35 mm and 40 mm are manufactured and the experimental results are compared with each other. As the height becomes greater, the fracture energy becomes higher. After the length of crack reaches 150 mm, the fracture energy of the specimen (h=35 mm) is greater than that of the specimen (h=40 mm). Fatigue test is also performed with DCB test specimen. As the height decreases, the fracture energy becomes higher. By the result obtained from this study, aluminum foam with adhesive joint can be applied to actual composite structure and its fracture property can possibly be anticipated.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1151-1154
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Study On Dispersion Stability Of Nickel Nanoparticles Synthesized By Wire Explosion In Liquid Media
Badanie stabilności dyspersji nanocząstek niklu wytworzonych metodą WEP w ciekłym medium
Autorzy:
Kim, C. K.
Lee, G.-J.
Lee, M. K.
Rhee, C. K.
Powiązania:
https://bibliotekanauki.pl/articles/356909.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nickel nanofluid
pulsed wire evaporation
surfactant
zeta potential
dispersion stability
nanocząstka niklu
środek powierzchniowo czynny
stabilność dyspersji
potencjał zeta
dyspersja
Opis:
In this study, nickel nanoparticles were synthesized in ethanol using portable pulsed wire evaporation, which is a one-step physical method. From transmission electron microscopy images, it was found that the Ni nanoparticles exhibited a spherical shape with an average diameter of 7.3 nm. To prevent aggregation of the nickel nanoparticles, a polymer surfactant was added into the ethanol before the synthesis of nickel nanoparticles, and adsorbed on the freshly synthesized nickel nanoparticles during the wire explosion. The dispersion stability of the prepared nickel nanofluids was investigated by zeta-potential analyzer and Turbiscan optical analyzer. As a result, the optimum concentration of polymer surfactant to be added was suggested for the maximized dispersion stability of the nickel nanofluids.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1379-1382
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
De-Lubrication Behavior Of Novel EBS Based Admixed Lubricant In Aluminum P/M Alloy
Zachowanie nowego lubrykantu na bazie EBS w trakcie spiekania proszku stopu aluminium
Autorzy:
Oh, M. C.
Seok, H.
Kim, H. J.
Ahn, B.
Powiązania:
https://bibliotekanauki.pl/articles/354258.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
admixed lubricant
compaction pressure
powder metallurgy
sintering
Al-Cu-Mg alloy
lubrykant
zagęszczanie
metalurgia proszków
spiekanie
stop Al-Cu-Mg
Opis:
The objective of the present research is to develop a novel lubricant for Al-Cu-Mg P/M alloy and to address the effects of the lubricant and compaction pressure on sintered properties. A lubricant mixture consisting of Ethylene Bis Stearamide, Zn-Stearate, and fatty acid was newly developed in this study, and the de-lubrication behavior was compared with that of other commercial lubricants, such as Ethylene Bis Stearamide, Zn-Stearate, and Al-Stearate. Density and transverse rupture strength of sintered materials with each lubricant were examined, respectively. The microstructural analysis was conducted using optical microscope.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1427-1431
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Hafnium and Zirconium to Glass Forming Ability, Thermal Stability, Plasticity Deformation and Crystallization of Ni-Free Pentabasic Ti-Based Bulk Metallic Glasses
Autorzy:
Oak, J.-J.
Kim, Y. H.
Bae, K.-C.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/352087.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ti-based alloy
metallic glass
Ti fiber
glass formability
plastic deformation
Opis:
The newly designed Ti-based bulk metallic glass (BMG) in which case of fracture behavior was observed 1990MPa to compressive strength with a wide plastic deformation around 7% after process of elastic deformation. This phenomenon can be compared with those of Ti-based alloys and other Ti-based BMGs and indicates high potential to be applied in use. It was evaluated the Ti-based BMG for thermal stability that the reduced glass parameters, ΔTx, Trg and γ, are 79K, 0.50 and 0.38, respectively. In addition, it reveals high activation energies for crystallization in which are estimated to Ex1 = 291.77 ±9.71 kJ/mol, Ex2 = 588.77 ±28.88 kJ/mol and Ex3 = 330.26 ±3.61 kJ/mol on kissinger plotting in this study.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1081-1087
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Heat Treatment on Microstructure and Impact Toughness of Ti-6Al-4V Manufactured by Selective Laser Melting Process
Autorzy:
Lee, K.-A.
Kim, Y.-K.
Yu, J.-H.
Park, S.-H.
Kim, M.-C.
Powiązania:
https://bibliotekanauki.pl/articles/354570.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
selective laser melting
Ti-6Al-4V
microstructure
impact toughness
heat treatment
Opis:
This study manufactured Ti-6Al-4V alloy using one of the powder bed fusion 3D-printing processes, selective laser melting, and investigated the effect of heat treatment (650°C/3hrs) on microstructure and impact toughness of the material. Initial microstructural observation identified prior-β grain along the building direction before and after heat treatment. In addition, the material formed a fully martensite structure before heat treatment, and after heat treatment, α and β phase were formed simultaneously. Charpy impact tests were conducted. The average impact energy measured as 6.0 J before heat treatment, and after heat treatment, the average impact energy increased by approximately 20% to 7.3 J. Fracture surface observation after the impact test showed that both alloys had brittle characteristics on macro levels, but showed ductile fracture characteristics and dimples at micro levels.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1341-1346
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect Of Different Mechanical Milling Processes On Morphology And Microstructural Changes Of Nano And Micron Al-Powders
Wpływ różnych procesów mielenia na morfologię i mikrostrukturę nanometrycznych i mikronowych proszków Al
Autorzy:
Kim, H.-S.
Madavali, B.
Eom, T.-J.
Kim, C.- M.
Koo, J.-M.
Lee, T. H.
Hong, S.-J.
Powiązania:
https://bibliotekanauki.pl/articles/355715.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al alloys
high-energy ball milling
low energy ball milling
plastic deformation
stopy Al
wysokoenergetyczne mielenie kulkowe
mielenie energooszczędne
odkształcenia plastyczne
Opis:
In this research, effect of the various mechanical milling process on morphology and microstructural changes of nano and micron Al-powders was studied. The milling of Al-powders was performed by both high energy and low energy ball milling process. The influence of milling (pulverizing) energy on the structural changes of Al-powders was studied. Al-nanoparticles were agglomerated during the MA and its size was increased with increasing milling while micron Al-powder gets flattened shape during high energy ball milling due to severe plastic deformation. Meanwhile, structural evolution during high energy ball milling of the nano powder occurred faster than that of the micron powder. A slight shift in the position of X-ray diffraction peaks was observed in nano Al-powders but it was un-altered in macro Al-powders. The variation in lattice parameters was observed only for nano Al powders during the high energy ball milling due to lattice distortion.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1235-1239
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Fe Content on the Microstructure and Mechanical Properties of Ti-Al-Mo-V-Cr-Fe Alloys
Autorzy:
Bae, K.-C.
Oak, J.-J.
Kim, Y. H.
Park, Y. H.
Powiązania:
https://bibliotekanauki.pl/articles/351896.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Ti alloy
near-β titanium alloy
aircraft applications
structural material
landing gear
Opis:
To investigate the effect of Fe content on the correlation between the microstructure and mechanical properties in near-b titanium alloys, the Ti-5Al-5Mo-5V-1Cr-xFe alloy system has been characterized in this study. As the Fe content increased, the number of nucleation sites and the volume fraction of the α phase decreased. We observed a significant difference in the shape and size of the α phase in the matrix before and after Fe addition. In addition, these morphological deformations were accompanied by a change in the shape of the α phase, which became increasingly discontinuous, and changed into globular-type α phase in the matrix. These phenomena affected the microstructure and mechanical properties of Ti alloys. Specimen #2 exhibited a high ultimate tensile strength (1071 MPa), which decreased with further addition of Fe.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 2B; 1105-1108
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study On The Electro-Refining Of Tin In Acid Solution From Electronic Waste
Badanie elektrorafinacji cyny w roztworze kwasu z e-odpadów
Autorzy:
Son, S. H.
Park, S. C.
Kim, J. H.
Kim, Y. H.
Lee, M. S.
Ahn, J.-W.
Powiązania:
https://bibliotekanauki.pl/articles/352665.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electrorefining
tin
electronic waste
recycling
high purity
elektrorafinacja
cyna
odpady elektroniczne
recykling
Opis:
The tin metal could be retractable from wasted tin scrap, sludge, and wasted electroplated solution hydrometallurgical treatment, and purification process. In order to be used as resource of electronic devices, the retracted crude metal should be purified to the extent of higher than 99.9%. In this study, tin electro-refining process was performed to purify the casted tin crude metal at various experimental conditions: at the current density of 3, 5A/dm2, and in various electrolytes such as hydrochloric acid, sulfuric acid and methansulfonic acid. Additional experiment was conducted using Rotating Disk Electrode (RDE) in order to investigate the rate determining step of tin electro-refining process. The current efficiency, 65.6%, was achievable at the condition of current density, 5A/dm2, and in the electrolyte of Hydrochloric acid. During tin electro-refining process, impurity dissolved from tin crude metal into the electrolyte was analyzed using Inductively Coupled Plasma Optical Emission Spectrometer (ICP-OES), and the result showed the concentration of impurity metal gradually increased. Quantitative analysis on casted tin crude metal showed that it consists of tin with 93.9 wt.% and several impurity metals of Ag, Bi, Pb, Cu, and etc. After tin electro-refining process, the purity of tin increased up to 99.985 wt.%.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1217-1220
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies