Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "volute" wg kryterium: Temat


Wyświetlanie 1-4 z 4
Tytuł:
Effect of exit blade angle, viscosity and roughness in centrifugal pumps investigated by CFD computation
Autorzy:
Li, W.
Powiązania:
https://bibliotekanauki.pl/articles/1934039.pdf
Data publikacji:
2011
Wydawca:
Politechnika Gdańska
Tematy:
centrifugal pump
impeller
volute
viscosity
performance
blade angle
viscous oil
Opis:
It has long been known that the exit blade angle plays a very important role in the performance of a centrifugal pump handling water or viscous oil. The effect of exit blade angle on the performance and flow of centrifugal pumps is usually investigated experimentally. However, due to the high cost and limited data that can be obtained by experiment, currently there is a great need for this effect to be studied numerically by means of computational fluid dynamics (CFD). At present, extensive comparisons between experiment and simulation regarding the performance of viscous oil and flow in centrifugal pumps with different exit blade angles are not available. Hydraulic performance and flow details in the impeller and the volute of a centrifugal pump with an exit blade angle of 44o were investigated numerically with the CFD code Fluent, using water and viscous oil as the working fluid, respectively. The effect of exit blade angle was then elucidated by comparing the performance and flow with that of a pump with an exit blade angle of 20o. It was determined that the results for the performance and flow obtained by means of CFD were in qualitative agreement with the observations. The sudden-rising-head effect is dependent on roughness and viscosity. The unstable zone in the theoretical head curve of the impeller at a low flow rate was attributed to the strong reaction of the volute to the flow in the vicinity of the impeller exit. The flow in the impeller with a large exit blade angle was subject to separation near the blade pressure side, however, a large exit blade angle helped improve the pump performance of viscous oil.
Źródło:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk; 2011, 15, 1; 21-41
1428-6394
Pojawia się w:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Projektowanie sprężyn paraboloidalnych
Volute springs design
Autorzy:
Sileikis, W.
Powiązania:
https://bibliotekanauki.pl/articles/209855.pdf
Data publikacji:
2007
Wydawca:
Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
Tematy:
projektowanie
Internet
sprężyny paraboloidalne
konstrukcja maszyn
design
volute springs
machine construction
Opis:
W pracy przedstawiono podstawowe wiadomości na temat taśmowych sprężyn paraboloidalnych oraz przykłady zastosowania ich w technice. Opisano aplikację internetową do projektowania taśmowych sprężyn paraboloidalnych, umożliwiającą obliczenie ich parametrów konstrukcyjnych.
The paper presents basic information and examples of volute springs application in industry. There is described web application for designing volute springs to provide calculations of their parameters.
Źródło:
Biuletyn Wojskowej Akademii Technicznej; 2007, 56, sp.1; 97-104
1234-5865
Pojawia się w:
Biuletyn Wojskowej Akademii Technicznej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical investigation of flow in mixed-flow pump with volute
Autorzy:
Sedlar, M.
Powiązania:
https://bibliotekanauki.pl/articles/1967635.pdf
Data publikacji:
2001
Wydawca:
Politechnika Gdańska
Tematy:
CFD
computational fluid dynamics CFD
flow separation
cavitation
Navier-Stokes equation
unsteady phenomena
mixed-flow pump
volute
Opis:
The work considers the modelling of flow in a complete mixed-flow pump with volute, including tip leakage flows, using both quasi-steady and true transient models of rotor/stator interaction. The CFX-TASCflow CFD package from AEA Technology is applied to calculate flows for a wide range of flow rates from about 0.2 to 1.4 Q/sub 0pt/. Fairly detailed flow structures have been predicted based on the flow rates, especially impeller inlet recirculation and separation on the suction side of the blades for suboptimal rates of flow, as well as strong secondary flows and separation in the volute for off-design conditions. The rotor/stator interaction influence on flow phenomena both in the impeller and volute have been investigated with very interesting results, providing good insight into the dynamics of flow close to the volute tongue. Based on the computational results, pump performance curves (Q-H, Q- eta /sub h/ and Q-P, eta /sub h/ being the hydraulic efficiency) have been obtained. The data from this numerical investigation have been used to improve the inlet part of the impeller blades, especially close to the tip. The geometry modifications have resulted in reduced cavitation in the impeller as well as noise at suboptimal rates of flow.
Źródło:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk; 2001, 5, 4; 595-602
1428-6394
Pojawia się w:
TASK Quarterly. Scientific Bulletin of Academic Computer Centre in Gdansk
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Experimental and numerical investigation of radial forces acting on centrifugal pump impeller
Badania doświadczalne i obliczenia numeryczne sił promieniowych działających na wirnik pompy odśrodkowej
Autorzy:
Karaśkiewicz, K.
Szlaga, M.
Powiązania:
https://bibliotekanauki.pl/articles/139526.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
rotodynamic pump
radial thrust
pump with single volute
affinity laws
measurement of radial forces
pompa wirowa
napór promieniowy
pompa z pojedynczą spiralą
prawa podobieństwa przepływu
pomiar sił promieniowych
Opis:
The paper presents the results of measurements and predictions of radial thrust in centrifugal pump with specific speed ns = 26. In the pump tested, a volute with rectangular cross-section was used. The tests were carried out for several rotational speeds, including speeds above and below the nominal one. Commercial code ANSYS Fluent was used for the calculations. Apart from the predictions of the radial force, the calculations of axial thrust were also conducted, and correlation between thrust and the radial force was found. In the range of the measured rotational speeds, similarity of radial forces was checked.
W artykule przedstawiono wyniki pomiarów i obliczeń naporu osiowego w pompie odśrodkowej o wyróżniku szybkobieżności ns = 26. W badanej pompie została zastosowana spirala zbiorcza o przekroju prostokątnym. Badania wykonano dla kilku prędkości obrotowych, w tym powyżej i poniżej nominalnej. W obliczeniach wykorzystano kod ANSYS Fluent. Oprócz obliczeń siły promieniowej, zostały przeprowadzone obliczenia naporu osiowego oraz stwierdzono obecność korelacji między obiema siłami. W zakresie mierzonych prędkości obrotowych zbadane zostało również podobieństwo sił promieniowych.
Źródło:
Archive of Mechanical Engineering; 2014, LXI, 3; 445-454
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-4 z 4

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies