Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "spalania" wg kryterium: Temat


Tytuł:
Comparison of combustion characteristics of S.I. engine fuelled with butane and gasoline on lean operating limit
Porównywanie charakterystycznych parametrów procesów spalania w silniku o ZI przy zasilaniu benzyną i butanem w zakresie ubogich mieszanek
Autorzy:
Kowalewicz, A.
Pawlak, G.
Różycki, A.
Powiązania:
https://bibliotekanauki.pl/articles/263749.pdf
Data publikacji:
1999
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
proces spalania
ubogie mieszanki
Opis:
According to worldwide trend, many research centres focus on fuelling of SI engine with homogeneous and heterogeneous lean mixtures. In the Departament of Internal Combustion Engines in Radom Technical University some investigation on fuelling of SI engine with lean air - fuel mixtures was carried out. For these experiments butane was used, because it has relatively wide flammability limits and it seems to be a good fuel for experiments on fuelling the engine with the lean mixture. The objectives of this paper are: - analysis of the influence of air-fuel ratio (A/F) on combustion characteristic parameters, engine performances anf thermal efficiency, - comparison of fuelling with butane with convetional carburettor fuelling in the aspect of above mentioned data, - optimisation of combustion of butane-air-mixture on account of spark timing. The results of the investigation show that there is possible to fuel the engine with lean butane - air mixture in efficient way. Its performance and efficiency are at the same level as for gasoline carburettor engine. There are also some potential possibilities of increasing advantages, which are hidden in modification of fuel system. The improvement of it, especially application of injection of the liquid gas could strongly improve abovere presented results, which will be used as a base for the next examination of modified engine.
Zgodnie ze światowymi trendami wiele centrów badawczych skupia się na badaniach zasilania silników o ZI ubogimi mieszankami homogenicznymi i heterogenicznymi. W Zakładzie Silników i Pojazdów Politechniki Radomskiej wykonano badania zasilania silnika o ZI ubogimi mieszankami. Badania przeprowadzono na silniku do samochodu Cinquecento. Jako paliwa użyto butanu, który ma szerokie granice palności. Cele tych badań były następujące: - analiza wpływu udziału powietrza do paliwa ma charakterystyczne parametry procesu spalania, osiągi silnika i jego sprawność cieplną, - porównanie zasilania butanem i benzyną za pomocą standardowego układu gaźnikowego, - optymalizacja kąta zapłonu przy zasilaniu butanem. Wyniki badań wykazały, że jest pełna zamienność paliw (benzyna na butan) w zakresie ubogich mieszanek. Osiągi silnika i parametry procesów spalania są bardzo zbliżone przy obu sposobach zasilania. Istnieją dalsze możliwości poprawienia osiągów silnika obniżenia jego emisji przez zastosowanie wtrysku gazu bezpośrednio do cylindra, co będzie przedmiotem dalszej pracy.
Źródło:
Archiwum Motoryzacji; 1999, 3; 121-134
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zagadnienie spalania
Problem of combustion
Autorzy:
Litke, Benedykt Julian
Powiązania:
https://bibliotekanauki.pl/articles/135990.pdf
Data publikacji:
2019
Wydawca:
Wyższa Szkoła Techniczno-Ekonomiczna w Szczecinie
Tematy:
proces spalania
równania analityczne
produkty spalania
combustion process
analytical equation
combustion products
Opis:
Wstęp i cele: W pracy opisano spalanie jest proces gwałtownego utleniania substancji palnej, podczas którego wywiązuje się duża ilość ciepła. Celem spalania jest uzyskanie ciepła o wysokiej temperaturze, a w niektórych urządzeniach również spalin o dużym ciśnieniu, jak np. w silnikach spalinowych tłokowych. Celem pracy jest ogólne omówienie paliw i ich własności, zapotrzebowania powietrza do spalania, współczynnika nadmiaru powietrza oraz ilości i składu spalin. Materiał i metody: Materiał stanowią źródła z literatury z zakresu termodynamiki. W pracy zastosowano metodę analizy teoretycznej. Wyniki: Rezultatem analizy jest opracowanie równań przedstawiających ilość produktów powstających przy spalaniu różnych składników paliw stałych, ciekłych i gazowych. Z równań tych można obliczyć objętość spalin, powstałych ze spalenia 1 kg paliwa, jako sumę wszystkich produktów spalania oraz składników niepalnych powietrza. Wnioski: Znajomość objętości spalin powstających przy spalaniu 1 kg paliwa w danym urządzeniu jest niezbędna do obliczania przekrojów kanałów lub rurociągów odprowadzających gazy spalinowe.
Introduction and aim: The paper describes combustion is a process of rapid oxidation of a combustible substance during which a large amount of heat is generated. The purpose of combustion is to obtain heat at a high temperature, and in some devices also high-pressure exhaust gas, such as piston internal combustion engines. The purpose of the work is to discuss fuels and their properties in general, combustion air demand, excess air coefficient, and the amount and composition of exhaust gases. Material and methods: Material covers some sources based on the literature in the field of thermodynamics. The method of theoretical analysis has been shown in the paper. Results: The result of the analysis is the development of equations showing the amount of products formed when burning various components of solid, liquid and gaseous fuels. From these equations, the volume of exhaust gas resulting from the combustion of 1 kg of fuel can be calculated as the sum of all combustion products and non-flammable air components. Conclusion: Knowledge of the volume of flue gas resulting from the combustion of 1 kg of fuel in a given device is necessary for calculating the cross-sections of ducts or pipelines that discharge flue gases.
Źródło:
Problemy Nauk Stosowanych; 2019, 10; 69-74
2300-6110
Pojawia się w:
Problemy Nauk Stosowanych
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Optymalizacja procesów spalania na przykładzie pieca rafineryjnego
Optimisation of combustion processes in a refinery furnace
Autorzy:
Rodriguez, F.
Tova, E.
Morales, M.
Portilla, M. A.
Cańadas, L.
Powiązania:
https://bibliotekanauki.pl/articles/109141.pdf
Data publikacji:
2011
Wydawca:
AXIS MEDIA
Tematy:
optymalizacja procesów spalania
piec rafineryjny
technologia kontrolowanej komory spalania (KKS)
system monitoringu
program Expert
Opis:
Artykuł opisuje technologię zwiększającą efektywność spalania przy jednoczesnej redukcji emisji zanieczyszczeń. Została ona opracowana, opatentowana i wdrożona w przemyśle przez hiszpańską firmę INERCO S.A.
The article describes a technology which increases the combustion efficiency while reducing levels of pollutants emissions. The technology was developed, patented, and implemented for industrial use by INERCO S.A., a Spanish company.
Źródło:
Piece Przemysłowe & Kotły; 2011, 1; 35-40
2082-9833
Pojawia się w:
Piece Przemysłowe & Kotły
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of mass transfer in marine engine with prechamber combustion spark ignition system
Autorzy:
Pielecha, Ireneusz
Powiązania:
https://bibliotekanauki.pl/articles/2128135.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
marine engine
prechamber combustion spark ignition
combustion process modeling
combustion thermodynamics
silnik morski
zapłon iskrowy spalania w komorze wstępnej
modelowanie procesu spalania
termodynamika spalania
Opis:
The development of combustion systems construction is associated with the possibility of increasing the thermal or overall efficiency of an internal combustion engine. The combustion systems currently in use (mainly related to direct fuel injection) are increasingly being replaced by hybrid systems, including direct and indirect injection. Another alternative is the use of prechambers in new combustion systems. This article concerns the thermodynamic aspect of this issue – namely, the assessment of the inter-chamber f low of a marine engine equipped with a prechamber combustion spark ignition system. The research was carried out using mainly one-dimensional simulation apparatus, and detailed analyses were presented using three-dimensional modeling. The tests included the engine model at medium load. Differences in mass f lows were shown at different diameters and different numbers of holes from the preliminary chamber (while maintaining the same cross-sectional area). Similar values of excess air coefficient during ignition of the fuel dose in the prechamber were observed, which resulted in changes in the f low between the prechamber and the main chamber. The differences in mass f low affected the temperatures achieved in the individual combustion chambers. Based on three-dimensional analyses, the mass transfer rate between the chambers and the temperature distribution were assessed during fuel ignition initiated in the prechamber.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2021, 69, 2; e136744, 1--8
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of mass transfer in marine engine with prechamber combustion spark ignition system
Autorzy:
Pielecha, Ireneusz
Powiązania:
https://bibliotekanauki.pl/articles/2173605.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
marine engine
prechamber combustion spark ignition
combustion process modeling
combustion thermodynamics
silnik morski
zapłon iskrowy spalania w komorze wstępnej
modelowanie procesu spalania
termodynamika spalania
Opis:
The development of combustion systems construction is associated with the possibility of increasing the thermal or overall efficiency of an internal combustion engine. The combustion systems currently in use (mainly related to direct fuel injection) are increasingly being replaced by hybrid systems, including direct and indirect injection. Another alternative is the use of prechambers in new combustion systems. This article concerns the thermodynamic aspect of this issue – namely, the assessment of the inter-chamber f low of a marine engine equipped with a prechamber combustion spark ignition system. The research was carried out using mainly one-dimensional simulation apparatus, and detailed analyses were presented using three-dimensional modeling. The tests included the engine model at medium load. Differences in mass f lows were shown at different diameters and different numbers of holes from the preliminary chamber (while maintaining the same cross-sectional area). Similar values of excess air coefficient during ignition of the fuel dose in the prechamber were observed, which resulted in changes in the f low between the prechamber and the main chamber. The differences in mass f low affected the temperatures achieved in the individual combustion chambers. Based on three-dimensional analyses, the mass transfer rate between the chambers and the temperature distribution were assessed during fuel ignition initiated in the prechamber.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2021, 69, 2; art. no. e136744
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ barwników na stopień palności poliamidu 6
Dyes Influence on Fire Properties of Polyamide 6
Autorzy:
Kopański, M.
Powiązania:
https://bibliotekanauki.pl/articles/373141.pdf
Data publikacji:
2013
Wydawca:
Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej im. Józefa Tuliszkowskiego
Tematy:
poliamid
barwnik
pożar
ciepło spalania
produkty spalania
polyamide
dyestuff
fire
heat of combustion
combustion products
Opis:
W poniższej pracy przedstawiono wyniki badań reakcji barwionych poliamidów PA 6 na ogień. Badania przeprowadzono w oparciu o normy zapalności materiałów poddawanych bezpośredniemu działaniu płomienia (PN-EN 11925-2) i intensywności wydzielania ciepła (ISO 5660-1/2). Uzyskane wyniki badań (intensywności wydzielania ciepła, emisji masowej tlenku i dwutlenku węgla, długość zniszczenia próbki) wskazują na znaczący wpływ substancji barwiącej na właściwości pożarowe poliamidu 6.
The following paper presents reaction results of colored/stained polyamides PA 6 to fire. Materials testing was conducted according to the standards ISO 5660-1/2 and PN-EN 11925-2. The results (heat release rate, emission monoxide carbon and dioxide carbon, length of burning) show the significant influence of the dye on the properties of fire-colored polyamide.
Źródło:
Bezpieczeństwo i Technika Pożarnicza; 2013, 3; 41-48
1895-8443
Pojawia się w:
Bezpieczeństwo i Technika Pożarnicza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Kaloryczność paliw stałych
Autorzy:
Ferens, W.
Powiązania:
https://bibliotekanauki.pl/articles/1818090.pdf
Data publikacji:
2014
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
ciepło spalania
paliwa stałe
własności paliw
Opis:
W pracy analizowano wpływ pochodzenia oraz składu paliw stałych na ciepło spalania i wartość opałową. Stwierdzono dominujący wpływ zawartości pierwiastka węgla oraz balastu, rozumianego jako suma udziałów popiołu i tlenu, na kaloryczność paliw stałych. Porównano ciepło spalania i wartość opałową paliw i wykazano, że różnica między tymi wielkościami jest charakterystyczna dla danej grupy paliw. Zestawiono formuły pozwalające oceniać ciepło spalania paliw na podstawie ich składu pierwiastkowego oraz na podstawie zawartości części palnych i balastu. Przeprowadzono porównanie wartości uzyskanych przy pomocy tych formuł z wartościami mierzonymi i dokonano ich oceny dokładności.
Źródło:
Zeszyty Energetyczne; 2014, 1; 149--158
2658-0799
Pojawia się w:
Zeszyty Energetyczne
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research on combustion mode of methanol micro-reciprocating piston internal combustion engine
Autorzy:
Tang, Gang Zhi
Wang, Shuai Bin
Zhang, Li
Shang, Hui Chao
Powiązania:
https://bibliotekanauki.pl/articles/329276.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
micro-energy power systems
combustion diagnosis
combustion model
methanol
silnik spalinowy
diagnostyka spalania
model spalania
metanol
Opis:
Constrained by the micro-space structure, it is proposed to use platinum wire incandescent ignition combustion mode to achieve the operation of internal combustion engine. However, the combustion test of the platinum wire incandescent ignition in miniature piston internal combustion engine shows: the combustion mode of micro-space platinum wire incandescent ignition has a poor combustion characteristic, low heat release rate, long combustion duration, and low combustion pressure. Therefore, a homogenous charge compression ignition mode is proposed to realize the operation of miniature internal combustion engine. However, it is found that the compression combustion cannot be come true in the cold start-up state of the micro engine. And the compression combustion in the first cycle was realized by the way of increasing the temperature of the cylinder block and platinum wire appropriately. The results show that: The maximum heat release rate is obviously improved and the combustion duration shortened by 28.6ºCA, and pmi increased by 76%. So, a novel hybrid combustion mode of in-cylinder compression combustion supported by the platinum wire incandescent ignition is put forward, through the way of adjusting the temperature of platinum wire, and this combustion mode is regarded as the ideal combustion mode of micro reciprocating piston internal combustion engine.
Źródło:
Diagnostyka; 2020, 21, 1; 97-103
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Improvement of energy balance in automotive vehicle, based on combustion engine losses
Autorzy:
Olszowiec, P.
Luft, M.
Łukasik, Z.
Powiązania:
https://bibliotekanauki.pl/articles/393197.pdf
Data publikacji:
2017
Wydawca:
Polskie Stowarzyszenie Telematyki Transportu
Tematy:
recuperation
turbogenerator
exhaust system
rekuperacja
komora spalania
Opis:
The paper presents an innovative method to increase the overall effi ciency of the internal combustion engine. The presented method is based on the kinetic energy derived from the fl ow of exhaust gases in the exhaust system of the internal combustion engine. Th is energy is used to drive a high speed turbogenerator which is integrated with the gained energy system management. Such a system, which uses energy otherwise lost in the engine exhaust system, allows the acquisition of additional electrical energy. As a result, it improves the energy balance of a motor vehicle. Th is is particularly important in a situation of constantly expanding system of electric receivers in vehicles. Th e paper presents an analysis of the research results of the system of energy recovery, carried out on turbo supercharged engine with spark ignition. Th e article also gives the research results on the impact of the proposed system on the environment.
Źródło:
Archives of Transport System Telematics; 2017, 10, 1; 33-37
1899-8208
Pojawia się w:
Archives of Transport System Telematics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Combustion process control in system with semi-open combustion chamber for spark ignition engines
Kontrola procesu spalania w systemie półotwartej komory spalania dla silników z zapłonem iskrowym
Autorzy:
Leżański, T.
Sęczyk, J.
Wolański, P.
Powiązania:
https://bibliotekanauki.pl/articles/133345.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
internal combustion engines
spark ignition engines
combustion process
combustion process control
visualization of combustion process
silniki spalinowe
silniki o zapłonie iskrowym
proces spalania
kontrola procesu spalania
wizualizacja procesu spalania
Opis:
A few operation examples of combustion system with semi open combustion chamber for spark ignitron engines has been presented in this paper. This system has been designed in Aircraft Engine Department of Heat Engineering Institute of Warsaw University of Technology. The principal problem of operation this system is to assure that jet-stream commences to outflow from prechamber to main combustion chamber when the piston is at TDC and that it will have a sufficient energy quickly to displace all main chamber. This is a task for combustion control system. This can be obtained by correct selection of the system operating parameters: the volume ratio of prechamber to total combustion chamber, the hole diameter in partition, the igniter locations, the ignition advance angle. If this system has operate correctly it was obtained the shortening of combustion time about 2.2 time, growth of maximum cycle pressure 1.9 time and increase of combustion efficiency 1.4 time, in comparison to standard combustion chamber. This research results concern the test conducted using rapid compression machine.
W artykule przedstawiono kilka przykładów pracy systemu z półotwartą komora spalania przeznaczonego dla silników o zapłonie iskrowym. System ten został opracowany w Zakładzie Silników Lotniczych Instytutu Techniki Cieplnej Politechniki Warszawskiej. Podstawowym problemem pracy tego systemu jest zapewnienie, że początek wypływu strumienia z komory wstępnej do zasadniczej nastąpi wówczas, kiedy tłok znajduje się w GMP i że energia strugi będzie wystarczająca, aby szybko przebyć całą komorę zasadniczą. Takie jest zadanie układu sterowania. Może to być osiągnięte przez właściwy dobór parametrów pracy systemu: proporcji objętości komory wstępnej do całej objętości komory spalania, średnicy otworu w przegrodzie, miejsca zapłonu oraz kąta wyprzedzenia zapłonu. Jeśli ten system działał prawidłowo, to uzyskiwano: skrócenie czasu spalania około 2.2 razy, zwiększenie ciśnienia maksymalnego cyklu 1,9 razy i wzrost sprawności spalania 1,4 razy, w porównaniu ze standardową komorą spalania. Wyniki te dotyczą badań, które były prowadzone z zastosowaniem maszyny pojedynczego sprężu.
Źródło:
Combustion Engines; 2013, 52, 3; 434-441
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena możliwości wykorzystania gazu ze zgazowania osadów ściekowych
Evaluation of the possibility of the sewage sludge gasification gas use
Autorzy:
Werle, S.
Powiązania:
https://bibliotekanauki.pl/articles/127419.pdf
Data publikacji:
2016
Wydawca:
Towarzystwo Chemii i Inżynierii Ekologicznej
Tematy:
zgazowanie
wysuszone osady ściekowe
normalna prędkość spalania
stabilność spalania
gasification
dried sewage sludge
laminar burning velocity
combustion stabilization
Opis:
W pracy zaprezentowano wyniki badań eksperymentalnych wyznaczania normalnej prędkości spalania gazu ze zgazowania osadów ściekowych. Wykorzystano metodę palnika Bunsena. Jednocześnie wyznaczono rozkład temperatury w płomieniu. Wyniki pokazują, że istnieją optymalne warunki prowadzenia procesu spalania gazu ze zgazowania osadów ściekowych, przy których możliwe jest stabilne prowadzenie tego procesu z jednoczesnym efektywnym wywiązywaniem się ciepła. Wyniki wskazują, że niskokaloryczne gazy z termicznego przetwarzania biomasy odpadowej mogą stanowić źródło paliwa na potrzeby produkcji finalnych postaci energii.
The paper presents the results of experimental investigation of the laminar flame speed of the sewage sludge gasification gas. Bunsen burner method was used. Additionally, the temperature distribution in the flame was determined. The results show that there are optimum conditions for conducting combustion of the sewage sludge gasification gas, with which it is possible to carry out the stable process with effective heat release. The results indicate that low calorific gas from the thermal processing of waste biomass can be a source of fuel for the production of final forms of energy.
Źródło:
Proceedings of ECOpole; 2016, 10, 1; 341-348
1898-617X
2084-4557
Pojawia się w:
Proceedings of ECOpole
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Combustion stability of dual fuel engine powered by diesel-ethanol fuels
Autorzy:
Nowak, Łukasz
Tutak, Wojciech
Powiązania:
https://bibliotekanauki.pl/articles/133775.pdf
Data publikacji:
2019
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
combustion stability
heat release
dual fuel
ignition delay
combustion phases
stabilność spalania
wydzielanie ciepła
gazodiesel
opóźnienie zapłonu
fazy spalania
Opis:
The paper presents result of combustion stability assessment of dual fuel engine. The authors analyzed results of co-combustion of diesel fuel with alcohol in terms of combustion stability. The comparative analysis of both the operational parameters of the engine and the IMEP, as the parameters determining the stability of the combustion process, were carried out. It was analyzed, among others values of the COVIMEP coefficient, the spread of the maximum pressure value, the angle of the position of maximum pressure and the probability density distribution of the IMEP. The experimental investigation was conducted on 1-cylinder air cooled compression ignition engine. The test engine operated with constant rpm equal to 1500 rpm and constant angle of start of diesel fuel injection. The engine was operated with ethanol up to 50% of its energy fraction. The influence of ethanol on ignition delay time spread and end of combustion process was evaluated. It turns out that the share of ethanol does not adversely affect the stability of ignition.
Źródło:
Combustion Engines; 2019, 58, 3; 155-161
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena wytrzymałości komory spalania silnika rakietowego na paliwo stałe
Evaluation of the solid propellant rocket motor burning chamber resistance
Autorzy:
Nowicki, J.
Powiązania:
https://bibliotekanauki.pl/articles/234733.pdf
Data publikacji:
2006
Wydawca:
Wojskowy Instytut Techniczny Uzbrojenia
Tematy:
silniki rakietowe
komory spalania
rocket engines
combustion chamber
Opis:
W artykule przedstawiono analizę wytrzymałości mechanicznej komory spalania silnika rakietowego na paliwo stałe. Podano obciążenia na jakie narażona jest komora w czasie pracy silnika rakietowego oraz związane z nimi naprężenia powstające w ściance komory. Przedstawiono zależności na podstawie, ktorych oblicza się te naprężenia. Podano uproszczony sposob sprawdzenia wytrzymałości komory. W oparciu o tę metodę przedstawiono ocenę wytrzymałości komory spalania pocisku rakietowego M-21OF.
The analysis of mechanical resistance for the solid propellant rocket motor burning chamber is presented in the paper. The loads and stresses the chamber wall has to withstand at the rocket motor operation are described. The formulas to calculate the stresses and a simplified way to check the chamber’s resistance are given. The mentioned tools were used to evaluate the burning chamber resistance of the missile M-21OF.
Źródło:
Problemy Techniki Uzbrojenia; 2006, R. 35, z. 100; 99-107
1230-3801
Pojawia się w:
Problemy Techniki Uzbrojenia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie wpływu dodatków energetycznych na wybrane właściwości heterogenicznego stałego paliwa rakietowego o zmniejszonej zawartości HCL w produktach spalania
Studies of the influence of energetic additives on selected properties of heterogeneous solid rocket propellant with low content of HCL in combustion products
Autorzy:
Magnuszewska, P.
Bogusz, R.
Florczak, B.
Powiązania:
https://bibliotekanauki.pl/articles/235821.pdf
Data publikacji:
2017
Wydawca:
Wojskowy Instytut Techniczny Uzbrojenia
Tematy:
HSRP
HTPB
LSR
szybkość spalania
LRM
burning rate
Opis:
W pracy przedstawiono wpływ takich dodatków jak: glin, magnez, pył aluminiowo-magnezowy (PAM) i boru na właściwości heterogenicznego stałego paliwa rakietowego (HSPR) na bazie HTPB, w którym chloran(VII) amonu został częściowo zastąpiony azotanem(V) sodu. Wprowadzając w skład paliw azotan(V) sodu zawartość chorowodoru (HCl) w produktach spalania zmniejszyła się. Za pomocą programu ICT-Code wyznaczono teoretyczne wartości właściwości termochemicznych i termodynamicznych takie jak izochoryczne ciepło spalania (Q), impuls specyficzny (Isp) i produkty spalania w komorze i dyszy silnika. W celu wyznaczenia właściwości balistycznych otrzymane paliwa spalono w laboratoryjnym silniku rakietowym (LSR). Zbadano właściwości reologiczne (lepkość pozorną) zawiesiny paliwa podczas procesu utwardzania, wrażliwość na bodźce mechaniczne (uderzenie, tarcie), temperaturę rozkładu, ciepło spalania i twardość.
The paper presents influence of additives like aluminium, magnesium, AMD (aluminium-magnesium dust) and boron on selected properties of heterogeneous solid rocket propellants (HSRP) based on HTPB in which ammonium (VII) chlorate was partly replaced by sodium(V) nitrate. The presence of sodium(V) nitrate reduces the content of hydrogen chloride (HCl) in combustion products. Theoretical values of thermochemical and thermodynamical properties like isochoric heat of combustion (Q), specific impulse (Isp) and combustion products in motor chamber and nozzle were identified by ICT-Code program. A laboratory rocket motor (LRM) was used to examine ballistic properties for prepared samples of propellants. Their temperature of decomposition, heat of combustion and hardness were tested both with sensitivity to mechanical stimuli (impact, friction) and rheological properties at curing.
Źródło:
Problemy Techniki Uzbrojenia; 2017, 46, 144; 15-30
1230-3801
Pojawia się w:
Problemy Techniki Uzbrojenia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie homogenicznego stałego paliwa rakietowego zawierającego dodatki modyfikujące szybkość spalania
Testing of homogeneous rocket solid propellant including components to modify the rate of burning
Autorzy:
Florczak, B.
Wolszakiewicz, T.
Gawor, T.
Powiązania:
https://bibliotekanauki.pl/articles/236241.pdf
Data publikacji:
2007
Wydawca:
Wojskowy Instytut Techniczny Uzbrojenia
Tematy:
paliwa rakietowe
proces spalania
rocket propellants
combustion process
Opis:
Przedstawiono wyniki badań homogenicznego stałego paliwa rakietowego składającego się z nitrocelulozy, nitrogliceryny i dodatków modyfikujących szybkość spalania. Zastosowanie dodatków modyfikujących proces spalenia, pozwoliło uzyskać paliwo o właściwych charakterystykach i parametrach eksploatacyjnych wyrażonych odpowiednimi przedziałami wartości kaloryczności, szybkości spalenia, współczynnika wrażliwości temperaturowej i wykładnika potęgowego występującego we wzorze na szybkość palenia paliwa w funkcji zmian ciśnienia. Otrzymanie korzystnych parametrów eksploatacyjnych paliwa okazało się możliwe dzięki synergizmowi zastosowanych komponentów modyfikatora procesu spalenia.
The results are presented in the paper over the testing of a homogeneous rocket solid propellant consisting of nitro-cellulose, nitro-glycerine and other components for modifying the rate of burning. The addition of components modifying the rate of burning resulted in receiving a propellant with desired specifications and characteristics of calorific value limits, burning rate, coefficient of temperature sensitivity and value of the power index in the formula describing the burning rate dependence on the pressure values. The synergism of components used in the propellant is the factor that makes possible to receive the product with good technical characteristics.
Źródło:
Problemy Techniki Uzbrojenia; 2007, R. 36, z. 103; 129-136
1230-3801
Pojawia się w:
Problemy Techniki Uzbrojenia
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies