Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "magnetic field measurement" wg kryterium: Temat


Wyświetlanie 1-10 z 10
Tytuł:
Nuclear magnetic precession measured with SQUIDs
Autorzy:
Burghoff, M.
Powiązania:
https://bibliotekanauki.pl/articles/156431.pdf
Data publikacji:
2007
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
SQUID
nuclear magnetic precession
low magnetic field measurement
Opis:
We have developed a superconducting quantum interference devices (SQUID) system measuring nuclear magnetic precession at very low magnetic fields with a spectral resolution beyond the natural line width of liquids. A coil system applies a magnetic polarization field and a perpendicular static detection field to the sample. The detection system for the very weak magnetic field generated by the processing nuclei consists of LTc-SQUID sensors in a liquid helium cryostat. We measured the 'H precession signal of benzene, distilled water and chloroform samples at various detection fields. With our set-up. broad band detection of the nuclear magnetic resonance of the investigated liquids with a very high resolution is possible. Benzene showed the narrowest natural resonance line width of 0.12 Hz followed by chloroform of about 0.17 Hz. The observed line widths increased linearly with the detection field with a slope independent of the investigated sample. This increase is attributed to the inhomogeneity of the detection field, rather than to intrinsic properties of the investigated liquids, and thus describes the properties of our measurement system. Reliable low field NMR and MRI depend strongly on field homogeneity of the detection field coils and the residual field inside the agnetically shielded room. At such low fields, high demands on the absolute homogeneity of the static field correspond to very moderate requirements on its relative homogeneity 111. Reduction of these system parameters and its influence is the prerequisite for a good frequency and spatial resolution. Here, we investigated our SQUID measurement system and estimated all main system parameters at very low fields below a microtesla.
Źródło:
Pomiary Automatyka Kontrola; 2007, R. 53, nr 9 bis, 9 bis; 17-20
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Temperature error of Hall-effect and magnetoresistive commercial magnetometers
Autorzy:
Nowicki, M.
Kachniarz, M.
Szewczyk, R.
Powiązania:
https://bibliotekanauki.pl/articles/141287.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnetic field measurement
magnetometers
Hall-effect
magnetoresistive
temperature error
Opis:
The paper presents a special measurement system for investigation of temperature influence on the indication of commercially available sensors of the magnetic field. Utilizing the developed system, several magnetoresistive and Hall-effect sensors were investigated within the temperature range from –30°C to 70°C. The obtained results indicate that sensitivity of most of the investigated sensors is unaffected, except the basic magnetoresistive device. However, Hall-effect sensors exhibit considerable temperature drift, regardless of the manufacturer.
Źródło:
Archives of Electrical Engineering; 2017, 66, 3; 625-630
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Issues involved in using the direct method for magnetic field strength measurement of electrical steel sheets – review
Problemy pomiaru natężenia pola magnetycznego blach elektrotechnicznych metodą bezpośrednią – przegląd
Autorzy:
Gaworska-Koniarek, D.
Bajorek, J.
Wilczyński, W.
Powiązania:
https://bibliotekanauki.pl/articles/159080.pdf
Data publikacji:
2016
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Elektrotechniki
Tematy:
pomiar natężenia pola magnetycznego
czujniki pola magnetycznego
metoda bezpośrednia
magnetic field strength measurements
magnetic field sensor
magnetic field measurement
direct method
Opis:
W artykule, na podstawie dokonanego przeglądu literatury, przedstawiono istniejące problemy pomiaru natężenia pola magnetycznego metodą pośrednią i bezpośrednią w blachach elektrotech-nicznych oraz próby ich rozwiązania. Opisano czujniki składowej natężenia pola magnetycznego stosowane najczęściej do pomiaru natężenia pola magnetycznego w blachach elektrotechnicznych.
The paper presents, based on a review of relevant literature, the existing problems of magnetic field strength measurements of electrical steel sheets by means of the indirect and direct methods. It also describes some attempts to solve these problems. The magnetic field strength sensors most widely used for testing electrical steel sheets are also discussed.
Źródło:
Prace Instytutu Elektrotechniki; 2016, 274; 71-82
0032-6216
Pojawia się w:
Prace Instytutu Elektrotechniki
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The magnetic field curvature correction algorithm dedicated for helmet mounted cueing systems
Autorzy:
Adamski, M.
Szelmanowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/949523.pdf
Data publikacji:
2018
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
transport
avionics
helmet-mounted cueing systems
errors of the angular positioning
magnetic field measurement
flat coil profile modelling
Opis:
The article presents the new built in Poland helmet mounted cueing system NSC-1 Orion with a magnetic method, dedicated to the multi-purpose helicopters W-3PL Gluszec. This system uses the magnetic field generated by the system of three mutually orthogonal electric coils. The principle of operation of this system is described and the method of determining the angular position of the pilot's helmet relative to the helicopter's cabin using the reference magnetic field and the directional cosines matrix are discussed. Electrical flat coils, constructed in the Polish Air Force Institute of Technology (AFIT), generating a magnetic field with curved symmetry axis characteristics, causing errors in determining the angular position of the pilot's helmet are shown. As a way to minimize these errors, an original proprietary algorithm for correcting the negative impact of the magnetic field curvature generated by the on-board system has been presented. Mathematical relations describing the presented correction process as well as selected results of simulation and experimental investigations in the area of inaccuracy of the "before" and "after" systems of applying the developed algorithm were given. Inaccuracies determined from computer simulations of the developed mathematical relations were compared with experimental data from magnetic field measurements using the integrated three-axis sensor ADIS-16405, used in the laboratory of the AFIT Avionics Division for helmet control of the angular position of the moving observation and sighting head and reflector-search light.
Źródło:
Journal of KONES; 2018, 25, 2; 15-30
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the residual magnetic field measurement system for early identification of railway defects
Autorzy:
Rucki, Mirosław
Gockiewicz, Anna
Szumiata, Tadeusz
Powiązania:
https://bibliotekanauki.pl/articles/220497.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
residual magnetic field
measurement
rail inspection
uncertainty
repeatability
Opis:
The paper presents research on the capability of the residual magnetic field (RMF) measurement system to be applied to the railway inspection for the early non-destructive detection of defects. The metal magnetic memory (MMM) phenomena are analysed using normal component Hy of self-magnetic flux leakage (SMFL), and its tangential component Hx, as well as their respective gradients. The measurement apparatus is described together with possible factors that may affect the results of measurement. The Type A uncertainty estimation and repeatability tests were performed. The results demonstrate that the system may be successfully applied to detection of head check flaws.
Źródło:
Metrology and Measurement Systems; 2019, 26, 4; 687-696
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Sposób oceny małoczęstotliwościowego pola magnetycznego na statkach morskich
The way of assessment of low frequency magnetic field on board of ships
Autorzy:
Pałczyńska, B.
Spiralski, L.
Wyszkowski, J.
Powiązania:
https://bibliotekanauki.pl/articles/153580.pdf
Data publikacji:
2007
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
pomiary pola elektromagnetycznego
natężenie pola magnetycznego
electromagnetic field measurement
magnetic field intensity
Opis:
Przedstawiono sposób pomiaru natężenia pola magnetycznego w zakresie małych częstotliwości. Opisano komputerowy system pomiarowy, który umożliwia izotropowy pomiar wartości skutecznej oraz rejestrację przebiegów czasowych natężenia pola magnetycznego, a następnie metodą off-line dokonuje analizy częstotliwościowej sygnału pomiarowego. Przedstawiono wybrane wyniki pomiarów laboratoryjnych oraz przeprowadzonych w siłowni okrętowej statku badawczo-szkoleniowego.
The way of magnetic field measurement in low frequency range is presented. The computer measurement system, that allows isotropic measurement of magnetic field intensity RMS value and recording its waveforms and than off-line time-frequency analysis of the measured signal is described. Some selected results of the measurements, that were carried out in a laboratory and in the engine room of the research-training vessel are presented.
Źródło:
Pomiary Automatyka Kontrola; 2007, R. 53, nr 9 bis, 9 bis; 687-690
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Processing information from magnetic field sensors in helmet mounted cueing systems
Autorzy:
Szelmanowski, A.
Witoś, M.
Pazur, A.
Powiązania:
https://bibliotekanauki.pl/articles/1833874.pdf
Data publikacji:
2020
Wydawca:
Polskie Stowarzyszenie Telematyki Transportu
Tematy:
magnetic sensor
electromagnetic field
magnetic instrument
magnetic measurement
czujniki magnetyczne
pole elektromagnetyczne
przyrząd magnetyczny
pomiar magnetyczny
Opis:
In the XXI century, magnetic measurements are widely used in many diverse applications. In this paper, we present the practical application of magnetic measurements in the Helmet Mounted Cueing System (HMCS) on board military aircraft . We start with the research problem and proposed solutions (idea). Next, the theoretical basis of the helmet’s system operation are described. Herein, we include the characteristics of the Earth’s magnetic fi eld and the modeling of this (WMM 2015, IGRF 12, EMM2017), as well as the theory of magnetic fi eld distribution as generated in fl at coils, Helmholtz coils and anti-Helmholtz coils. In the later detailed part, we describe the metrological aspects of HMCS applications and the characteristics therein of diff erent magnetometers used in the tests, plus example test results. Finally, we describe ongoing research, while in the summary, we present further research possibilities and potential directions of research in the avionic implementation of magnetic phenomena in HMCS systems.
Źródło:
Archives of Transport System Telematics; 2020, 13, 1; 36--42
1899-8208
Pojawia się w:
Archives of Transport System Telematics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Device for Measuring the Rotational Speed of a Chain Sprocket of a Petrol Chainsaw
Autorzy:
Wróbel, Mateusz
Jakubek, Bartosz
Rukat, Wojciech
Powiązania:
https://bibliotekanauki.pl/articles/2123289.pdf
Data publikacji:
2021
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
magnetic field
chainsaw
rotational speed measurement
chain sprocket
hall effect sensor
Opis:
The procedure for determining the frequency-weighted RMS values of vibration accelerations in the case of petrol chainsaws proposes equal time shares of three operation modes of the chainsaw. In order to assess the actual operator’s vibration exposure, it is necessary to precisely determine the above-mentioned shares. In real-life conditions operation of chainsaws is characterized by frequent and significant rotational speed changes depending on the operation mode. Therefore, a prototype of dedicated device for measuring the rotational speed of a chain sprocket was developed. The article presents development requirements, encountered problems and their solutions, the prototype itself and functional test results.
Źródło:
Advances in Science and Technology. Research Journal; 2021, 15, 3; 99--107
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Indukcyjny czujnik prądu do zastosowań w pomiarach energii elektrycznej
Inductive current sensor for electrical energy measurement
Autorzy:
Wydźgowski, L.
Zaworski, Ł.
Zieliński, M.
Powiązania:
https://bibliotekanauki.pl/articles/152101.pdf
Data publikacji:
2008
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
czujnik prądu
pomiar energii elektrycznej
pole magnetyczne
current sensor
electrical energy measurement
magnetic field
Opis:
Referat dotyczy pomiaru prądu w licznikach energii elektrycznej. Zawiera krótkie omówienie stosowanych obecnie metod pomiaru prądu, oraz przedstawia opracowanie nowej konstrukcji czujnika. Referat zwiera wyniki przeprowadzonych symulacji komputerowych oraz weryfikację eksperymentalną zaproponowanego rozwiązania konstrukcyjnego nowego czujnika prądu. Czujnik ten spełnia wymagania metrologiczne niezbędne do zastosowań w pomiarach energii elektrycznej, charakteryzuje się dużą odpornością na zakłócające pola magnetyczne, a dzięki prostocie konstrukcji wyróżnia się niskim kosztem wykonania.
This paper describes the design parameters and construction of current sensor for energy metering based on inductive coils with no magnetic core. These sensors are contactless and can be used in remote conductors at high potentials. This sensor doesn't have iron core (unlike current transformer) so there is no non-linearity over a very wide measurement range. Unlike a shunt resistor, this sensor provides galvanic isolation and produces no heating.
Źródło:
Pomiary Automatyka Kontrola; 2008, R. 54, nr 6, 6; 395-398
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Silnik tarczowy do pojazdów elektrycznych - charakterystyka pola magnetycznego
Disc motor for electric vehicles - characteristic of magnetic field
Autorzy:
Sulima, R.
Rudeński, A.
Powiązania:
https://bibliotekanauki.pl/articles/159837.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Elektrotechniki
Tematy:
silniki bezrdzeniowe
silniki tarczowe
magnesy trwałe
pomiary indukcji magnetycznej
analiza polowa 3D
disc motor
coreless motor
permanent magnets
magnetic induction measurement
FEM 3D field analysis
Opis:
Artykuł opisuje konstrukcję, wykonane obliczenia oraz pomiary indukcji magnetycznej w bezrdzeniowym silniku tarczowym z magnesami trwałymi. Pomiary wykonano w stanie bezprądowym w dwu przypadkach: 1) przy rozmontowanym wirniku, t.j. na powierzchni magnesów przytwierdzonych do pojedynczej tarczy jarzmowej i 2) ze zmontowanym wirnikiem - pomiary w środku szczeliny powietrznej pomiędzy tarczami jarzmowymi z zamocowanymi magnesami. Wykonano obliczenia polowe 3D przedmiotowego silnika dla obu powyższych wariantów: z pojedynczą tarczą wirnika oraz ze zmontowanymi dwoma tarczami wirnika. Przeanalizowano i porównano wyniki pomiarów oraz obliczeń polowych silnika i stwierdzono znaczną zgodność uzyskanych wyników.
A coreless disc motor with permanent magnets, made in IEL was investigated with respect to the distribution and leakage of its magnetic field. Computations of the 3D field were made for verification. Neodymium magnets with remanence induction of Br = 1,3093 T were used to build the motor. The measurements were made using an FM 210 teslometer with a Hall probe, calibrated with an 1 T etalon. The investigations were performed using an open magnetic circuit (both discs mounted without armature). In the first case the measurements were made at the surface of magnets according to the net shown in Figure 3. The results are presented in Table 1 and Figure 4. Measurements with closed magnetic circuit were made at half width of the air gap at 9 points Table 3). The magnet was divided into 16 measuring fields, symmetrically with respect to axes x and y. The measurements were made at the edges of the middle 9 fields. Results of measurements and 3D computations are very close.
Źródło:
Prace Instytutu Elektrotechniki; 2012, 258; 41-58
0032-6216
Pojawia się w:
Prace Instytutu Elektrotechniki
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-10 z 10

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies