Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Diesel particulate matter" wg kryterium: Temat


Wyświetlanie 1-15 z 15
Tytuł:
Future needs for ship emission abatement and technical measures
Przyszłe potrzeby ograniczania emisji ze statków i techniczne środki ich realizacji
Autorzy:
Antes, T.
Szudyga, M.
Śliwiński, Ł.
Jaworek, A.
Krupa, A.
Balachandran, W.
Di Natale, F.
Gregory, D.
Jackson, M.
Powiązania:
https://bibliotekanauki.pl/articles/374561.pdf
Data publikacji:
2013
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
diesel engine
exhaust gas
diesel particulate matter
electrostatic scrubber
emission control
silnik Diesla
gaz wylotowy
ograniczenie emisji
Opis:
The International Maritime Organization (IMO) has revised air pollution regulations in MARPOL Annex VI. In 2012 Emission Control Areas (ECA) will limit fuel sulphur content to 1% and from 2015 to 0.1%). NOx emissions based on ships engine speed are also reduced for new vessels (2012 & 2016). Facing this legislation, ship owners have the alternative either to operate ships with costly low-sulphur fuels, or to keep using HFO but together with a gas cleaning equipment at the ship stack in order to reduce the rejected amount of SO2 gas in the atmosphere. To achieve this requirement, research and development organizations came out with proposing a solution that uses a device for cleaning exhaust gas of marine diesel engines. The paper presents a short communication about the DEECON project, which aim is to create a novel on-board after-treatment unit more advanced than any currently available. Each sub-unit of the system will be optimized to remove a specific primary pollutant. In particular, the technology within the DEECON system is based on novel or improved abatement techniques for reducing SOx, NOx, Particulate Matter (PM), CO and Volatile Organic Compounds (VOC). Some of these technologies are completely new for the maritime sector and they will represent a breakthrough in the reduction of the atmospheric emissions of ships, moving forward the performance of exhaust gas cleaning systems and fostering and anticipating the adoption of future and tighter regulatory requirements. In addition, an after-treatment strategy enables the possible adoption of alternative fuels, which often have their own emissions characteristics.
Na właścicieli statków i przewoźników morskich spadł obowiązek redukcji zanieczyszczeń pochodzących z ich działalności. Aby spełnić rygorystyczne wytyczne: dyrektyw Wspólnoty europejskiej, międzynarodowej organizacji morskiej (aneks VI, konwencji) MARPOL oraz praw wewnętrznych innych państw należałoby, w obszarach kontroli emisji, używać jako paliwa oleju napędowego o zmniejszonej zawartości siarki. Obszar kontroli emisji jest to obszar obejmujący Morze Bałtyckie, Morze Północne wraz z jego podejściami pod Kanał La-Manche oraz obszar wokół USA. Ze względu na wysokie ceny paliwa niskosiarkowego, duże koszty ewentualnych zmian technicznych przejścia na paliwo o niższej zawartości siarki spowoduje kilkakrotne zwiększenie opłat i zmniejszy atrakcyjność transportu morskiego. Naprzeciw tym wymaganiom wyszły jednostki badawczo rozwojowe, proponując rozwiązania polegające na zastosowaniu nowych, bardziej skutecznych urządzeń do końcowego oczyszczania spalin z okrętowych silników diesla. Artykuł jest komunikatem projektu o akronimie DEECON, którego głównym celem jest opracowanie innowacyjnego pokładowego urządzenia do oczyszczania spalin z okrętowych silników diesla składającego się z różnych modułów. Urządzenie to będzie optymalizowane w celu usunięcia najważniejszych zanieczyszczeń tj. SOx, NOx, PM, Lotnych Związków Organicznych (VOC) oraz tlenku węgla (CO). Niektóre z tych technologii są całkowicie nowe w przemyśle morskim i stanowią przełom w redukcji emisji zanieczyszczeń do atmosfery. Ponadto, takie rozwiązanie jest uniwersalne, umożliwia zastosowanie alternatywnych paliw do zasilania silników okrętowych, które często mają własne cechy emisji.
Źródło:
Transport Problems; 2013, 8, 3; 101-107
1896-0596
2300-861X
Pojawia się w:
Transport Problems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A field study on the possible attachment of DPM and respirable dust in mining environments
Autorzy:
Gaillard, Sallie
Sarver, Emily
Cauda, Emanuele
Powiązania:
https://bibliotekanauki.pl/articles/92194.pdf
Data publikacji:
2019
Wydawca:
Główny Instytut Górnictwa
Tematy:
diesel particulate matter
dust
transmission electron microscope
NIOSH method 5040
submicron particles
cząstki stałe w silnikach wysokoprężnych
kurz
elektronowy mikroskop transmisyjny
metoda NIOSH 5040
cząstki submikronowe
Opis:
Typcial monitoring procedures for diesel particulate matter (DPM) in mines include the collection of filter samples using particle size selectors. The size selectors are meant to separate the DPM, which is generally considered to occur in the submicron range (i.e.,<0.8 μm), from larger dust particles that could present analytical interferences. However, previous studies have demonstrated that this approach can sometimes result in undersampling, therefore, excluding significant fractions of the DPM mass. The excluded fraction may represent oversized DPM particles, but another possibility is that submicron DPM attaches to supramicron dust particles such that it is effectively oversized. To gain insights into this possibility, a field study was conducted in an underground stone mine. Submicron, respirable, and total airborne particulate filter samples were collected in three locations to determine elemental carbon (EC) and total carbon (TC), which are commonly used as analytical surrogates for DPM. Concurrent with the collection of the filter samples, a low-flow sampler with an electrostatic precipitator was also used to collect airborne particulates onto 400-mesh copper grids for analysis by transmission electron microscope (TEM). Results indicated that, while typical submicron sampling did account for the majority of DPM mass in the study mine, DPM-dust attachment can indeed occur. The effect of exposure to such attached particulates has not been widely investigated.
Źródło:
Journal of Sustainable Mining; 2019, 18, 2; 100-108
2300-1364
2300-3960
Pojawia się w:
Journal of Sustainable Mining
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impaktor kaskadowy jako metoda poboru nanoobiektów do analizy mikroskopowej
A cascade impactor as a method of collecting nano-objects for microscopic analysis
Autorzy:
Kozikowski, Paweł
Sobiech, Piotr
Oberbek, Przemysław
Jakubiak, Szymon
Powiązania:
https://bibliotekanauki.pl/articles/1845105.pdf
Data publikacji:
2021
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
nanocząstki
cząstki stałe spalin Diesla
pobieranie aerozolu
mikroskopia elektronowa
analiza rozkładu wielkości
nauki o zdrowiu
inżynieria środowiska
nanoparticles
Diesel particulate matter
sampling
scanning electron microscopy
particle size distribution analysis
health sciences
environmental engineering
Opis:
Pył zawieszony może być szkodliwy dla zdrowia ludzkiego, a ryzyko wystąpienia szkodliwych skutków zwiększa się z czasem narażenia. Obecnie grupami zawodowymi potencjalnie narażonymi na działanie nanomateriałów są ci, którzy je wytwarzają i dostarczają. Dlatego konieczne jest stosowanie urządzeń do zbierania i analizy cząstek stałych z wyłączeniem frakcji mikrometrycznej. W pracach badawczych pobierano cząstki zawarte w spalinach z silnika wysokoprężnego przy użyciu impaktora kaskadowego i analizowano z zastosowaniem skaningowej mikroskopii elektronowej. Obserwacje ujawniły duże rozbieżności między średnicami odcięcia d50 a średnicami ekwiwalentnymi obliczonymi na podstawie obrazów SEM, a także różnorodną morfologię zdeponowanych cząstek stałych pochodzących z silnika Diesla. Zakres tematyczny artykułu obejmuje zagadnienia zdrowia oraz bezpieczeństwa i higieny środowiska pracy będące przedmiotem badań z zakresu nauk o zdrowiu oraz inżynierii środowiska.
Particulate matter can be harmful to human health and the risk of harmful effects increases with the duration of exposure. Currently, the occupational groups that are potentially exposed to nanomaterials are those who manufacture and supply them. Therefore, it is necessary to use devices for the collection and analysis of solid particles with the exclusion of the ambient fraction. In this study, Diesel soot generated using Diesel engine has been collected with cascade impactor and analyzed by means of scanning electron microscopy. Observations revealed large discrepancies between the cut off diameter d50 and equivalent diameter calculated from SEM images and a number of types of Diesel particulate matter. This article discusses the problems of occupational safety and health, which are covered by health sciences and environmental engineering.
Źródło:
Podstawy i Metody Oceny Środowiska Pracy; 2021, 2 (108); 155-167
1231-868X
Pojawia się w:
Podstawy i Metody Oceny Środowiska Pracy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Lube oil consumptions impact on environment
Autorzy:
Krzymień, P.
Powiązania:
https://bibliotekanauki.pl/articles/246960.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
lubricating oil consumption
particulate matter
diesel particulate filter
Opis:
The problem of lube oil consumption has been the point of interest of scientists for years,first because of economy and later - because of stringent standards of environment protection. From the point of economy lube oil consumption is not a problem of modern engines. On the other hand even a brief look proves that there is a quite wide range of admissible consumption from negligible values up to even l litr per 100 km. The question is why this range is so wide. Possible answer is that engine manufacturers leave so wide margin taking into consideration situations of very short trips, mainly in towns, when engine runs not fully warmed up with greater clearances, especially within the piston-cylinder assembly. Any oil consumption results in emission of particulate matter, which conveys a weighty number of hydrocarbons of which the most manifest serious hazardous properties, mainly carcinogenic ones. Nowadays, standards of environment protection require for instance the use of diesel particle filters and the excessive oil consumption could lead to the premature damage of these devices. Correct operation of the DPF could be disturbed not only by the excessive oil consumption but also by the use of improper oil, i.e. the non-low ash one. Certain additives that improve oil properties could produce ash as a result of oil combustion, which could clog filter irreversibly.
Źródło:
Journal of KONES; 2010, 17, 2; 265-270
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Particulate matter emission reduction from marine diesel engines by electrohydrodynamic methods
Autorzy:
Sobczyk, Arkadiusz T.
Jaworek, Anatol
Marchewicz, Artur
Krupa, Andrzej
Czech, Tadeusz
Śliwiński, Łukasz
Charchalis, Adam
Powiązania:
https://bibliotekanauki.pl/articles/241550.pdf
Data publikacji:
2019
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
exhaust gases
marine diesel engines
particulate matter
PM
scrubber
Opis:
Particulate matter (PM) and gaseous compounds (SO2, NOx, VOC) emitted by diesel engines causes serious global environmental problems and health impact. Despite numerous evidences about the harmfulness of diesel particles, the PM emission by diesel engines used by ships, cars, agricultural machines, or power generators is still unregulated, and the efficient removal of PM from diesel exhausts is still the major technological challenge. In order to comply with the International Maritime Organization regulation, the NOx emission is reduced by using selected catalytic reactor, and sulphur oxide emission has been reduced by using fuels of low sulphur content. However, both of those measures cannot be used for the reduction of PM emission produced during combustion of marine fuels. The lack of appropriate regulations results from insufficiently developed technology, which could remove those particles from exhaust gases. Conventional scrubbers currently available on the market remove only sulphur oxide with required collection efficiency, but the collection efficiency for PM2.5 is below 50%. The article discusses the technical means used for the removal of PM from marine diesel engines via applying electrohydrodynamic methods, in particular electrostatic agglomeration, as a method of nanoparticles coagulation to larger agglomerates, which could operate in two-stage electrostatic precipitation systems, and electrostatic scrubbers, which remove particles by electrically charged water droplets. The experimental results were obtained for a 2-stroke 73 kW diesel engine fuelled with marine gas oil (MGO). The agglomerator allowed increasing the collection efficiency from diesel exhausts for PM2.5 particles by about 12%, compared to electrostatic precipitator operating without agglomerator, and the total mass collection efficiency was above 74%. The collection efficiency of electrostatic scrubber was higher than 95wt.%. The advantage of using the electrostatic scrubber is that it can also reduce the SO2 emission by more than 90%, when HFO is used.
Źródło:
Journal of KONES; 2019, 26, 3; 203-210
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Particulate matter emission from dual fuel diesel engine fuelled with natural gas
Autorzy:
Stelmasiak, Z.
Larisch, J.
Pielecha, J.
Pietras, D.
Powiązania:
https://bibliotekanauki.pl/articles/260157.pdf
Data publikacji:
2017
Wydawca:
Politechnika Gdańska. Wydział Inżynierii Mechanicznej i Okrętownictwa
Tematy:
dual fuel engine
natural gas
particulate matter
emission
opacity
Diesel engine
Opis:
The paper presents the results of examination of particulate matter emission from the Diesel engine FPT 1.3 MJT simultaneously fuelled with diesel oil and natural gas CNG. The basic premise for engine adaptation was the addition of a small amount of CNG to reduce exhaust gas opacity and particulate matter emission. At this assumption, diesel oil remained the basic fuel, with contribution amounting to 0,70-0,85 of total energy delivered to the engine. The dual fuel engine was examined using an original controller installed in the Diesel engine FPT 1.3 MJT which controlled the diesel fuel dose. The dose of the injected natural gas was controlled by changing the opening time of gas injectors at constant pressure in the gas collector. The examined issues included the exhaust gas opacity, and the total number and fractional distribution of the emitted particles. The measurements were performed at twenty selected measuring points corresponding to the New European Driving Cycle (NEDC) test. The performed tests have demonstrated a positive effect of gas addition on exhaust gas opacity and particulate matter emission. Depending on test conditions, the exhaust gas opacity was reduced by 10÷92%, and the total number of particles by 30÷40%. The performed tests have revealed that a small addition of gas can reduce the load of the DPF filter, extend its lifetime, and increase engine reliability. Longer time intervals between successive DPF filter regenerations improve ecological properties of the engine.
Źródło:
Polish Maritime Research; 2017, 2; 96-104
1233-2585
Pojawia się w:
Polish Maritime Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Marine engine exhaust gas emission aftertreatment system concept
Autorzy:
Myśków, J.
Borkowski, T.
Bludszuweit, M.
Frohlingsdorf, W.
Powiązania:
https://bibliotekanauki.pl/articles/247178.pdf
Data publikacji:
2011
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
exhaust emission
particulate matter
non-thermal plasma reactor
Opis:
In 2008 the International Maritime Organization - IMO decided to strengthen the requirements for new ships from 2011 - Tier II. However, for Emission Control Areas (ECAs), such as the Baltic Sea, stringent rules will apply from 1 January 2016 for new ships - Tier III. The new standards introduce restrictions on exhaust emissions from diesel engines - NOx and SOx. The paper presents proposal of new design an existing exhaust gas system of experimental marine diesel engine, which is situated in the Laboratory of Maritime Academy in Szczecin. The conception is due to meet to new environmental regulations. Arrangements of exhaust line, CFD model of the SCR reference plant, CFD model - inlet and outlet boundary conditions, pressure loss model for the catalytic elements, simulation results - streamlines, velocity distribution, reaction progress distribution ate presented in the paper as well design description of system of laboratory- 4-stroke and turbocharged engine. . The means of the reduction systems are based on conventional marine exhaust gas installation that includes noise silencer and soot-catcher. The after-treatment methods do not introduce significant changes in engine arrangement and operation. A new gas purifying system should be installed in the engine exhaust gas system.
Źródło:
Journal of KONES; 2011, 18, 4; 307-315
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Direct application of non-thermal plasma to PM reduction from marine diesel engines
Autorzy:
Myśków, J.
Borkowski, T.
Powiązania:
https://bibliotekanauki.pl/articles/242305.pdf
Data publikacji:
2009
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
marine diesel engine
exhaust emission
particulate matter
non-thermal plasma reactor
Opis:
This paper describes the experimental method - using non-thermal plasma reactor to cleaning exhaust gases - focused on PM compound. The demonstrator NTP reactor assembly was built as the by-pass in the real exhaust gas after-treatment system, in marine diesel engine. The reactor used to experiment is called - DBD (dielectric barrier discharge) type, The main aim of investigation was to analyze exhaust gas PM compounds under steady load of the engine. Test bench construction enables direct exhaust stream (main exhaust duet by-pass) to plasma reactor exposure with no additional components (coolers, orifices) that can change the exhaust gas properties. A new monitoring PM analyzing system, which can measure soot and SOF in low mass level, has been engaged. It consist of a diffusion charging (DC) detector with a dilution device for soot measurement, and two differential flame ionization detection (FID) method, which uses two FID detectors with separate sample lines. Exhaust emission reduction strategy for ships, Particulate Matters - PM in exhaust gas, non-thermal plasma reactor, experimental test bed and procedure, an example of reactor power measurement, test results provided into seven stages are presented in the paper.
Źródło:
Journal of KONES; 2009, 16, 2; 361-367
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena procesu aktywnej regeneracji układu DPF pojazdu dostawczego
Evaluation of the process of active regeneration of DPF system of a delivery vehicle
Autorzy:
Cieślikowski, B.
Powiązania:
https://bibliotekanauki.pl/articles/292249.pdf
Data publikacji:
2011
Wydawca:
Polskie Towarzystwo Inżynierii Rolniczej
Tematy:
filtr DPF
analiza spektralna
cząstki stałe PM
diesel particulate filter
spectral analysis
particulate matter (PM)
Opis:
Zaprezentowano zagadnienie tworzenia się osadów w filtrze cząstek stałych w wyniku stosowania oleju napędowego z udziałem biokomponentów jako współczesnego paliwa do zasilania silników z ZS. Analizy przeprowadzono na przykładzie filtra DPF pojazdu dostawczego wykorzystywanego w transporcie produktów dla potrzeb gospodarstwa sadowniczego. Ocenę procesu aktywnej regeneracji filtra dokonano z wykorzystaniem metod fluorescencji rentgenowskiej z dyspersją energii oraz metod spektroskopii w podczerwieni.
The issue of sediment formation in the particulate filter as a result of applying diesel oil with biocomponents as modern supply fuel for compression ignition engines was also presented. The analyses were conducted based on the example of diesel particulate filter (DPF) of a delivery vehicle used in fruit farm product transportation. The process of active regeneration was evaluated by means of energy dispersive x-ray fluorescence techniques as well as infrared spectroscopy techniques.
Źródło:
Inżynieria Rolnicza; 2011, R. 15, nr 5, 5; 47-54
1429-7264
Pojawia się w:
Inżynieria Rolnicza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Particulate matter emission from diesel engine fuelled with blends of diesel oil and ethyl tert-butyl ether
Emisja cząstek stałych z silnika o zapłonie samoczynnym zasilanego mieszaninami oleju napędowego z eterem etylo-tert-butylowym
Autorzy:
Górski, K.
Lotko, W.
Swat, M.
Powiązania:
https://bibliotekanauki.pl/articles/263295.pdf
Data publikacji:
2010
Wydawca:
Sieć Badawcza Łukasiewicz. Przemysłowy Instytut Motoryzacji
Tematy:
emisja cząsteczek stałych
ETBE
olej napędowy
silnik o zapłonie samoczynnym
diesel engine
diesel oil
particulate matter emission
Opis:
The article presents the results of research on particulate matter (PM) emission from ADCR diesel engine fuelled with blends of diesel oil and ethyl tert-butyl ether (ETBE). Measurements were done in conditions of 13-phase, stationary ECE R49 test. Results show, that PM emission was reduced with the use of all tested ETBE/diesel blends with respect to those of the neat diesel fuel. In case of tested engine fuelled with mixture ETBE20 its PM emission was decreased by a half when compared to diesel oil.
Artykuł przedstawia wyniki badań w zakresie oceny emisji cząstek stałych z silnika ADCR zasilanego mieszaninami oleju napędowego z eterem etylo-tert-butylowym (EETB). Pomiary wykonano w warunkach 13-fazowego testu stacjonarnego ECE R49. Wyniki wskazują, że emisja cząstek stałych była obniżona dla wszystkich badanych mieszanin w porównaniu do tej, którą uzyskano dla oleju napędowego. W przypadku badanego silnika zasilanego mieszaniną ETBE20 jego emisja cząstek stałych była obniżona o połowę w stosunku do zasilania olejem napędowym.
Źródło:
Archiwum Motoryzacji; 2010, 2; 119-126
1234-754X
2084-476X
Pojawia się w:
Archiwum Motoryzacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ biokomponentów paliwowych na charakter emisji cząstek stałych z silnika o ZS
The effect of bio-components of fuel on the emission character of particulate matter from diesel engines
Autorzy:
Swat, M.
Madej, K.
Powiązania:
https://bibliotekanauki.pl/articles/257173.pdf
Data publikacji:
2012
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Technologii Eksploatacji - Państwowy Instytut Badawczy
Tematy:
silnik o ZS
ochrona środowiska
biopaliwo
emisja PM
diesel engine
environmental protection
biodiesel
particulate matter emission
Opis:
Przedstawiono wyniki własnych badań wpływu biokomponentów paliwowych na emisję cząstek stałych PM z układu wylotowego silnika o zapłonie samoczynnym. Stwierdzono, że z eksploatacyjnego punktu widzenia najkorzystniejszym wydaje się paliwo B20, dla którego zaobserwowano mniejsze poziomy emisji wszystkich toksycznych składników spalin w porównaniu z emisjami uzyskanymi dla oleju napędowego, co przy niewielkich zmianach parametrów pracy silnika (M, Ne, ge) kwalifikuje to paliwo jako najlepsze. Ograniczenie poziomu emisji cząstek stałych w spalinach silnika o ZS przez badane biokomponenty paliwowe odbywa się głównie dzięki redukcji udziału frakcji nierozpuszczalnej INSOL w całkowitej masie emitowanych cząstek stałych.
Research results are presented of the bio-components of fuel's effect on the particulate matter emission from the exhaust systems of diesel engines. It was found that B20 fuel is the most preferred operationally. B20 was observed to have lower levels of all toxic exhaust components emissions, compared to emissions obtained for diesel fuel because B20 seems to be the best for small changes of engine parameters (M, Ne, ge). The reduction of the particulate matter emission level in the diesel engine exhaust gases by tested fuel bio-components is mainly due to the reduction of the INSOL insoluble fraction participation in the total mass of emitted particlate matter.
Źródło:
Problemy Eksploatacji; 2012, 3; 203-212
1232-9312
Pojawia się w:
Problemy Eksploatacji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Pomiar oraz identyfikacja cząstek stałych w spalinach silnika o zapłonie samoczynnym
The measurement and identification of the particulate matter in Diesel engine exhaust gases
Autorzy:
Mruk, A.
Cisek, J.
Powiązania:
https://bibliotekanauki.pl/articles/133051.pdf
Data publikacji:
2015
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
silnik o zapłonie samoczynnym
gazy spalinowe
cząstki stałe
identyfikacja PM
diesel engine
exhaust gases
particulate matter
PM identification
Opis:
W celu zidentyfikowania wśród cząstek stałych, cząstek innych niż sadza podano analizie filtry z badań silnika o zapłonie samoczynnym. Analizowane filtry pochodziły z badań 6-cylindrowego silnika sprawnego technicznie przy stałej prędkości obrotowej i obciążeniu. Wychwycone na filtrze cząstki podano obserwacji wykorzystując możliwości mikroskopu elektronowego i analizy spektralnej. Badania przeprowadzono na elektronowym mikroskopie skaningowym JSM-5800 firmy Jeol (Japonia), sprzężonym ze spektrometrem promieniowania rentgenowskiego Link ISIS 300 firmy Oxford Instruments Ltd. (Wielka Brytania). Stwierdzono, że na powierzchni filtra obok jednolitej w barwie i strukturze sadzy znajdują się inne, odróżniające się barwą i postacią. Cząstki te, po zlokalizowano udokumentowano i zbadano pod względem występujących w ich składzie pierwiastków. Określono również ich wymiary. Stwierdzono występowanie cząstek metalowych: stopy żelaza, cynku oraz krzemu. Wśród cząstek zaobserwowano również cząstki niejednorodne w postaci aglomeratów o zróżnicowanej budowie, złożonej z mikrocząstek różnego pochodzenia, zbudowanych z różnych materiałów.
To identify amid PM particulates the particles other than soot, the filters used in diesel engine testing have been analysed. Analysed filters had been applied in the study on a 6-cylinder, turbocharged diesel engine, technically proficient, working at constant torque and speed. The particles captured on the filter were put under observational study using the possibilities of electron microscope and spectroscopic analysis. The testing was done on a scanning electron microscope JSM-5800 of the firm Jeol (Japan), coupled with an X-ray spectrometer Link ISIS of the firm Oxford Instruments Ltd. (United Kingdom). It was found, that on the filter surface, besides the soot particles of uniform colour and structure, there were also other particles of different colour and form. These particles were localized and examined in terms of the chemical elements in their composition. Their dimensions also were determined. Metal particles were identified: ferrous alloy, zinc alloy and the silicon alloy. Amid the particulate matter, some heterogeneous particles were identified. They had the form of agglomerates of different structure, compound of elementary particles of different origins and materials.
Źródło:
Combustion Engines; 2015, 54, 3; 732-743
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The properties of a HDV diesel engine fuelled by crude rapeseed oil
Wlasciwosci silnika diesla zasilanego naturalnym olejem rzepakowym
Autorzy:
Cisek, J.
Mruk, A.
Hlavna, V.
Powiązania:
https://bibliotekanauki.pl/articles/793466.pdf
Data publikacji:
2011
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
crude rapeseed oil
rapeseed oil
energy parameter
exhaust gas
particulate matter
diesel engine
engine operation
breakdown
combustion engine
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2011, 11
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ emisji komunikacyjnej na stężenie dwóch form węgla i rozkład ich masy względem wielkości cząstek w aerozolu atmosferycznym obszaru miejskiego
Influence of Vehicular Traffic on Ambient Concentration and Mass Size Distribution of Two Fractions of Carbon in an Urban Area Atmospheric Aerosol
Autorzy:
Rogula-Kozłowska, W.
Rogula-Kopiec, P.
Klejnowski, K.
Błaszczyk, J.
Powiązania:
https://bibliotekanauki.pl/articles/1819029.pdf
Data publikacji:
2013
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
obszar miejski
emisja komunikacyjna
particulate air-pollution
diesel exhaust particles
chemical composition
elemental carbon
organic carbon
road
vehicles
matter
Opis:
Ambient particulate matter (PM) is a component of the natural environment and a certain number of particles that varies with time, having many different properties which also change over time, is constantly present in the air. It can be assumed that the scope of environmental effects of PM is the broadest among all air pollutants: it affects the human health, climate, ecological conditions and visibility. Organic carbon (OC) and elemental carbon (EC) are the two most important components of suspended dust. The continuously increasing road traffic intensity is highly correlated with increasing concentrations of both of these components in the air of urbanized areas all over the world. In spite of this, the amount of data on OC and EC concentrations in Poland is still insufficient, especially in the case of areas located close to busy roads. The aim of this study was to determine the influence of vehicular traffic on ambient concentrations of PM-related OC and EC, and their mass size distribution in a typical urban area of the Upper Silesia. PM samples were collected simultaneously at two sites located in the Katowice city. One of the selected measurement points was situated in the city centre and characterized so-called urban background. The second measurement point, located near the A4 motorway, was in the area directly exposed to the influence of traffic emission. Dust was sampled during two measurement periods (2–10 August and 15–22 September 2011) using thirteen-stage impactors – DEKATI Ltd. (DLPI, Dekati Low Pressure Impactor). Analysis for the content of OC and EC in the collected dust samples was carried out by means of a thermo-optical method with the use of a Sunset Laboratory OC/EC carbon analyzer. During the entire measurement program strict adherence to the rigorous requirements for quality control of the obtained results was ensured. Concentrations of PM1-, PM2.5- and PM10-related OC and EC in Katowice, near the A4 motorway, were close to values obtained in other parts of the world in different measurement periods, at traffic sites of similar characteristics. Also values of the concentration ratio of OC bound to PM10 and PM2,5 (or PM2,5) were similar to quantities determined in different locations. In Katowice, due to municipal emission and poor quality of vehicles travelling the roads, also the coarse fraction of dust was enriched in EC. This situation is unusual in comparison to other regions. The effect of emission from engines of the cars travelling the motorway manifested itself mainly by elevated EC concentrations compared to the urban background site. For TSP the EC concentration was higher, five times in the beginning of August and two times in the second half of September. The largest differences between EC concentrations in the location near the motorway and in the urban background area were observed for the PM0.06–0.108, PM0.108–0.17 and PM0.17–0.26 fractions. In both measurement periods, at the traffic site in Katowice, the maxima of mass size distribution of EC were in the diameter range characteristic for soot emitted from Diesel engines (0.108–0.26µm). The fact that the influence of exhaust emission from vehicles travelling the motorway on EC concentrations was more pronounced in the second half of September than in the first half of August, was caused by larger EC emission from various sources in Katowice during the period following summer holidays. Concentrations of organic carbon bound to TSP in both measurement periods in Katowice was only 10% higher in the urban traffic site than in the urban background site. The largest differences between OC concentrations near the motorway and in the urban background are observed in the ranges 0.06–0.17 and 1.0–2.5 µm. Maxima of the mass size distribution of PM-related OC, both at the urban traffic site and at the background site, were similar in both measurement periods. It was inferred that the small differences between OC concentrations in the traffic and the background site are caused by the process of secondary aerosol formation, less intensive near the motorway than in the urban site.
Źródło:
Rocznik Ochrona Środowiska; 2013, Tom 15, cz. 2; 1623-1644
1506-218X
Pojawia się w:
Rocznik Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Feature comparison regeneration particulate filter with the catalytic coating and the use of oxidation catalyst
Sravnenie vozmozhnostejj regeneracija sezhevogo fil'tra s kataliticheskim pokrytiem i primenieniem okislitel'nogo nejjtrolizatora
Autorzy:
Shekhovtsov, Y.
Zaigrayev, L.
Powiązania:
https://bibliotekanauki.pl/articles/793068.pdf
Data publikacji:
2013
Wydawca:
Komisja Motoryzacji i Energetyki Rolnictwa
Tematy:
diesel particle filter
regeneration
catalytic oxidation
soot
harmful emission
exhaust gas
nitrogen oxide
particulate matter
carbon monoxide
hydrocarbon
sulphur compound
Źródło:
Teka Komisji Motoryzacji i Energetyki Rolnictwa; 2013, 13, 4
1641-7739
Pojawia się w:
Teka Komisji Motoryzacji i Energetyki Rolnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-15 z 15

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies