Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "lifetime" wg kryterium: Temat


Tytuł:
Record-based inference and associated cost analysis for the Weibull distribution
Autorzy:
Doostparast, M.
Powiązania:
https://bibliotekanauki.pl/articles/205931.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Instytut Badań Systemowych PAN
Tematy:
cost analysis
likelihood function
record data
total time on test
Weibull model
lifetime model
Opis:
In statistical process control, record schemes are used to reduce the total time on test for the inspection inquiry. In these schemes, units are examined sequentially and successive minimum values are recorded. On the basis of record data, Samaniego and Whitaker (1986) obtained the maximum likelihood (ML) estimate of the mean for an exponential distribution. Since the two parameter Weibull model, as an extension of the exponential distribution, has a wide range of application, Hoinkes and Padgett (1994) derived the record-based ML estimators for the parameters of interest in this model. This paper shows that the ML estimates of the Weibull parameters do not always exist for the basis of records. Thus, a new scheme is proposed, in which the ML estimates of the parameters always exist. An analytic cost-based comparison between the usual and the New scheme is also carried out. Finally, some concluding remarks and open problems are formulated.
Źródło:
Control and Cybernetics; 2015, 44, 1; 163-177
0324-8569
Pojawia się w:
Control and Cybernetics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Diagnostics of control rod drive. Possibilities to extend its lifetime at NPPs
Diagnostyka napędu pręta sterującego. Możliwości zwiększenia czasu eksploatacji napędów w elektrowniach atomowych
Autorzy:
Druzhinin, I.
Sapozhnikova, K.
Taymanov, R.
Powiązania:
https://bibliotekanauki.pl/articles/329298.pdf
Data publikacji:
2008
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
elektromagnetyczny liniowy silnik krokowy
czujnik położenia
pręt sterujący
czas eksploatacji
reaktor jądrowy
linear stepping electromagnetic drive
control rod position sensor
lifetime
nuclear reactor
Opis:
According to specifications, lifetime of a linear stepping electromagnetic drive in WWER-1000 nuclear reactors is limited by the pre-assigned lifetimes of the drive components such as electromagnets, a latch assembly, drive rack, and control rod position sensor. The lifetime of the drive components is from 7 to 20 years. On the basis of diagnostics of these components under real conditions, actual lifetimes of the components at nuclear power plant (NPP) were forecasted. It is shown that in order to extend the lifetime of the drive components up to the reactor lifetime (60 years), it is necessary to replace the sensor of the DPL-type by the new one (of the DPL-KV type) and to decrease the electromagnet temperature. The Measuring and Diagnostic System with the DPL-KV sensor enables diagnosing the sensor, electronic processing unit and drive. Economic effect due to the cumulative technical decisions is estimated to be 7 mln.euro per NPP unit.
Zgodnie z dokumentacją czas eksploatacji elektromagnetycznych silników krokowych prętów sterujących w reaktorach jądrowych WWER-1000 jest ograniczony ustalonymi czasami eksploatacji ich składników (blok przesunięcia, pręt, elektromagnesy, czujnik) - od 7 do 20 lat. Na podstawie wyników diagnostyki tych składników w warunkach realnych została zrobiona prognoza ich rzeczywistej żywotności w elektrowniach atomowych. Wykazano, że w celu wydłużenia czasu eksploatacji składników do czasu życia reaktora (60 lat) trzeba wymienić czujnik DPL na inny, bardziej niezawodny - DPL-KV i znacznie obniżyć temperaturę elektromagnesów. Układ pomiarowo-diagnostyczny wyposażony w czujnik DPL-KV pozwala przeprowadzać diagnostykę czujnika, osprzętu elektronicznego i silnika. Całkowity efekt ekonomiczny wprowadzenia zaproponowanych rozwiązań technicznych jest szacowany na 7 milionów Euro na blok energetyczny.
Źródło:
Diagnostyka; 2008, 3(47); 89-93
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie wpływu domieszki Gd na stopień zdefektowania struktury szkła tellurowego
Studying influence of element Gd on voids degree of structure the tellurite glass
Autorzy:
Filipecki, J.
Golis, E.
Kotynia, K.
Chamerski, K.
Powiązania:
https://bibliotekanauki.pl/articles/168534.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Ceramiki i Materiałów Budowlanych
Tematy:
szkła tellurowe
defekty
anihilacja
spektroskopia czasów życia pozytonu
tellurite glasses
defects
annihilation
positron lifetime spectroscopy
Opis:
Materiałem badawczym było szkło tellurowe. Badaniom poddano szkło bazowe TeO2-P2O3-ZnO-LiNbO3 oraz szkło domieszkowane gadolinem (TeO2-P2O3-ZnO-LiNbO3)(Gd2O3). W celu dokonania analizy własności strukturalnych wykorzystano metodę pomiarów czasów życia pozytonów PALS (Positron Annihilation Lifetime Spectroscopy). W proponowanej metodzie możliwa jest identyfikacja defektów strukturalnych trudnych do wychwycenia innymi tradycyjnymi metodami pomiarowymi. Przeprowadzone badania wykazały istnienie dwóch składowych czasów życia pozytonów τ1 i τ2. W oparciu o model dwustanowy obliczono parametry wychwytu pozytonów, które pozwalają wyciągnąć wnioski o charakterze i stopniu zdefektowania badanych szkieł tellurowych.
The tellurite glass such as: TeO2-P2O3-ZnOLiNbO3 as a reference glass and (TeO2-P2O3-ZnO-LiNbO3)(Gd2O3) has been studied. The positron lifetime PALS (Positron Annihilation Lifetime Spectroscopy) was used to analyze the structural properties of tellurite glasses. The proposed method, can identify structural defects which are difficult to capture by other traditional methods. The study showed the existence of two components τ1 and ττ. The basis of the two-state model parameters were calculated capture of positrons, which allow you to draw conclusions about the nature and degree of defect studied tellurite glasses.
Źródło:
Szkło i Ceramika; 2015, R. 66, nr 1, 1; 17-19
0039-8144
Pojawia się w:
Szkło i Ceramika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Implementation of mathematical model of thermal behavior of electronic components for lifetime estimation based on multi-level simulation
Autorzy:
Frivaldsky, M.
Pridala, M.
Drgona, P.
Powiązania:
https://bibliotekanauki.pl/articles/140808.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electrolytic capacitor
lifetime model
lifetime estimation
system-level simulation
Opis:
The main purpose of the paper is the proposal of multi-level simulation, suited for the evaluation of the lifetime of critical electronic devices (electrolytic capacitors). The aim of this issue is to imagine about the expected operation of complex and expensive power electronic systems, when the failure of the most critical component occurs. For that reason, various operational conditions and various physical influences must be considered (e.g. mechanical, humidity, electrical, heat stress), where nonlinearities are naturally introduced. Verification of the proposal is given, whereby the life-time estimation of an electrolytic capacitor operated in a DC-DC converter during various operational conditions is shown. At this point electrical and heat stress is considered for lifetime influence. First, the current state in the field of mathematical modeling of the lifetime for electrolytic capacitors, considering main phenomena is introduced. Next, individual sub-models for multi-level simulation purposes are developed, including a thermal simulation model and electrical simulation model. Several complexities of individual models are mutually compared in order to evaluate their accuracy and suitability for further use. Proper simulation tools have been mutually linked and data transfer was secured, in order to have the possibility of investigation of a lifetime depend on the changes of various variables.
Źródło:
Archives of Electrical Engineering; 2017, 66, 2; 339-350
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A new approach to diagnostic symptom assessment based on information content measures
Nowa metoda oceny symptomów diagnostycznych oparta na miarach zawartości informacji
Autorzy:
Gałka, T.
Powiązania:
https://bibliotekanauki.pl/articles/327786.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
lifetime consumption
diagnostic symptom
information content
wyczerpywanie żywotności
symptom diagnostyczny
zawartość informacji
Opis:
A complex diagnostic object typically generates a large number of diagnostic symptoms. For proper lifetime consumption monitoring it is necessary to select those which best represent technical condition deterioration. Such selection may be based on the Singular Value Decomposition method. The paper presents a novel alternative approach, which employs an information content measure. As the end of object life is approached, symptoms are to an increasing extent dominated by deterministic lifetime consumption processes and therefore become more predictable. Thus symptoms with the highest information content decrease rate should be considered most useful. For a proper assessment, however, symptom sensitivity to condition parameters should also be addressed. A new measure referred to as representativeness factor is proposed. Suitability of such approach is demonstrated for the fluid-flow system of a large steam turbine.
Złożone obiekty diagnozowania zwykle są źródłem wielu symptomów diagnostycznych. Dla właściwego monitorowania wyczerpywania żywotności należy wybrać te z nich, które najlepiej odwzorowują degradację stanu technicznego. Wybór ten można oprzeć na metodzie rozkładu względem wartości szczególnej. W pracy przedstawiono nowatorskie alternatywne podejście, w którym wykorzystuje się miarę zawartości informacji. Wraz ze zbliżaniem się do końca życia obiektu symptomy są w coraz większym stopniu określone przez deterministyczne procesy ubytku żywotności, a zatem stają się coraz bardziej przewidywalne. Za najbardziej użyteczne należy zatem uznać symptomy z najszybszym spadkiem zawartości informacji. We właściwej ocenie należy jednak uwzględnić także wrażliwość symptomu na parametry stanu. Zaproponowano nową miarę określoną jako współczynnik reprezentatywności. Przydatność takiego podejścia została zademonstrowana na przykładzie układu przepływowego turbiny parowej.
Źródło:
Diagnostyka; 2016, 17, 3; 103-108
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Diagnozowanie stanu układów przepływowych maszyn wirnikowych na podstawie symptomów drganiowych
Diagnostics of the fluid-flow system condition in rotating machines on the basis of vibration-based symptoms
Autorzy:
Gałka, T.
Powiązania:
https://bibliotekanauki.pl/articles/328790.pdf
Data publikacji:
2004
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
układ przepływowy
ocena żywotności
wibrodiagnostyka
turbiny parowe
fluid-flow system
lifetime assessment
vibrodiagnostics
steam turbines
Opis:
Stan układu przepływowego ma zasadnicze znaczenie dla funkcjonowania maszyny. Ocena tego stanu i jego ewolucji czasowej może być zrealizowana w sposób pośredni, na podstawie ana-lizy symptomów drganiowych. Wymaga to opracowania odpowiedniego modelu i procedur. Na przykładzie turbin parowych przedstawiono możliwości oceny ewolucji stanu układu prze-pływowego na podstawie analizy trendów drgań, z zastosowaniem diagnostyki ilościowej wyko-rzystującej kryterialne poz.iomy symptomów. Zaprezentowano przykłady oparte na ponad 10-letniej obserwacji kilku turbin w energetyce krajowej. Wyniki zostały porównane z obliczeniami trwałości resztkowej wybranych elementów układów przepływowych.
Condition of the fluid-flow system is of prime importance for machine operation. Determina-tion of this condition and its time history can be done indirectly, on the basis of vibration symptom analysis. This calls for a suitable model and relevant procedures. For a particular case of steam tur-bines, possibilities of the fluid-flow system condition evolution have been shown, employing quan-titative diagnostics based on critical symptom values. Examples shown are based on data from several turbines in Polish utility power plants, covering over 10 years of operation. Results have been compared with residual lifetime calculations for a number of fluid-flow system elements.
Źródło:
Diagnostyka; 2004, 30, T. 1; 179-182
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Generalized extended Marshall-Olkin family of lifetime distributions
Autorzy:
Goldoust, Mehdi
Mohammadpour, Adel
Powiązania:
https://bibliotekanauki.pl/articles/2034093.pdf
Data publikacji:
2022-03-15
Wydawca:
Główny Urząd Statystyczny
Tematy:
compound distribution
hazard rate function
lifetime distribution
maximum likelihood estimation
power series distribution
Opis:
We introduce a new generalized family of nonnegative continuous distributions by adding two extra parameters to a lifetime distribution, called the baseline distribution, by twice compounding a power series distribution. The new family, called the lifetime power series-power series family, has a serial arrangement of parallel structures, which extends the Marshall and Olkin structure. Four special models are discussed. A mathematical treatment of the new distributions is provided, including ordinary and incomplete moments, quantile, moment generating and mean residual functions. The maximum likelihood estimation technique is used to estimate the model parameters and a simulation study is conducted to investigate the performance of the maximum likelihood estimates. Its applicability is also illustrated by means of two real data sets.
Źródło:
Statistics in Transition new series; 2022, 23, 1; 55-74
1234-7655
Pojawia się w:
Statistics in Transition new series
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
PALS investigations of matrix Vycor glass doped with molecules of luminescent dye and silver nanoparticles. Discrepancies from the ETE model
Autorzy:
Gorgol, M.
Jasińska, B.
Reisfeld, R.
Powiązania:
https://bibliotekanauki.pl/articles/147152.pdf
Data publikacji:
2015
Wydawca:
Instytut Chemii i Techniki Jądrowej
Tematy:
positron annihilation lifetime spectroscopy (PALS)
porous glass
lumogen dye ROT-305
silver nanoparticles
Vycor glass
Opis:
A thermal stability of three materials: undoped reference Vycor glass, glass filled with ROT-305 red dye, and silver nanoparticles was investigated by positron annihilation lifetime spectroscopy (PALS) in a broad temperature range (from 93 to 473 K). The attempt of pore size calculations from the ortho-positronium lifetime data was performed using the extended Tao-Eldrup (ETE) model. Below room temperature, a significant decrease in lifetime values of the longest-lived component was found for all the samples. This effect could not be explained by thermal shrinkage of the material and is probably caused by interaction of -Ps with a Vycor glass matrix. The greatest discrepancy from the ETE model predictions was observed for the reference glass. Doping the base material with dye molecules and silver nanoparticles resulted in similar small decrease in this discrepancy. After reheating the samples to the room temperature, the PALS components returned to the initial values. In the temperature range of 293–473 K, quite good agreement between PALS results and the ETE model predictions was observed for the reference glass and the glass incorporated with dye molecules. The observed small discrepancy in this range could possibly be partly explained by thermal expansion of the material. For the glass doped with silver nanoparticles, a significant change in PALS parameters was observed in the temperature range from 403 to 473 K.
Źródło:
Nukleonika; 2015, 60, No. 4, part 1; 717-720
0029-5922
1508-5791
Pojawia się w:
Nukleonika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ architektury i protokołów komunikacyjnych na przepustowość i czas nieprzerwanej pracy bezprzewodowych sieci sensorowych
The impact of architecture and algorithms used in sensor networks on its throughput and lifetime
Autorzy:
Goszczyński, T.
Powiązania:
https://bibliotekanauki.pl/articles/277304.pdf
Data publikacji:
2014
Wydawca:
Sieć Badawcza Łukasiewicz - Przemysłowy Instytut Automatyki i Pomiarów
Tematy:
sieci bezprzewodowe
sieci sensorowe
czas nieprzerwanej pracy
przepustowość sieci
symulacja
wireless networks
sensor networks
network lifetime
network throughput
Opis:
Sieci sensorowe, przeznaczone do zbierania danych dotyczących środowiska oraz do lokalizacji i śledzenia obiektów poruszających się w przestrzeni, powinny być optymalizowane ze względu na wymagany jak najdłuższy czas nieprzerwanej pracy jej węzłów oraz jak największą skuteczność przesyłania zbieranych danych. W artykule przedstawiono matematyczne odwzorcowanie i analizę systemu sieci przedstawioną w formie programu liniowego, określającego czas nieprzerwanej pracy sieci oraz analizę przepustowości dla dwóch modeli sieci, jak również dla różnych algorytmów śledzenia ruchomych obiektów. Przedstawiono także przykład symulacji pracy sieci.
Wireless sensor networks can be used for localization and tracking of moving targets. The article presents mathematical analysis of lifetime and throughput for two types of network structures and different algorithms used. Valuation of results obtained is presented.
Źródło:
Pomiary Automatyka Robotyka; 2014, 18, 11; 102-107
1427-9126
Pojawia się w:
Pomiary Automatyka Robotyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fatigue lifetime correction of structural joints Indexed by: of opencast mining machinery
Autorzy:
Grabowski, Paweł
Jankowiak, Artur
Marowski, Witold
Powiązania:
https://bibliotekanauki.pl/articles/2038154.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
fatigue life
lifetime assessment
supporting structure
welded joints
opencast mining machinery
Opis:
Opencast mining machinery represents a group of large-scale individually manufactured technical objects operated with long-life requests. Since their manufacturers are obliged to provide product that will reach declared time of life, fatigue strength and durability conditions have to be taken into account for superstructures to meet the requirements. The paper highlights main problems occurring while assessing fatigue lifetime during design. Firstly, the short survey of current state of the art regarding the approach to this problem is presented. Secondly, the most important reasons of unsatisfactory accuracy of the assessments are discussed. As a main objective of the study, the authors introduce the unique method of continuous fatigue lifetime correction for the welded superstructures during the machine lifecycle, as a remedy for this group of machinery. Furthermore, results and experience from adapting the approach in real object are presented, including fatigue lifetime correction due to the real intensity of loading acquired from a bucket-wheel excavator during its longlasting operation. It is expected that proposed procedure can help to improve credibility of fatigue lifetime assessment of heavy earthmoving machinery.
Źródło:
Eksploatacja i Niezawodność; 2021, 23, 3; 530-539
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Trwałość narzędzi w procesach kucia
Tool lifetime in forging processes
Autorzy:
Gronostajski, Z.
Kaszuba, M.
Hawryluk, M.
Nowak, B.
Powiązania:
https://bibliotekanauki.pl/articles/211705.pdf
Data publikacji:
2015
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Obróbki Plastycznej
Tematy:
kucie
inżynieria powierzchni
trwałość
narzędzia
forging
surface engineering
lifetime
tools
Opis:
W artykule omówiono najważniejsze mechanizmy niszczące narzędzia w procesach kucia, takie jak: zużycie ścierne, zmęczenie cieplno-mechaniczne, odkształcenie plastyczne, pękanie zmęczeniowe, zużycie adhezyjne i utlenianie. Wykazano, że intensywność zużycia zmienia się wraz ze zmianą parametrów procesu lub miejsca na narzędziu, co jest zdeterminowane przez czas kontaktu pomiędzy matrycą i odkuwką oraz zmianami temperatury. Natomiast w literaturze wymienione zjawiska na ogół analizowane są oddzielnie i nie ma dokładnego opisu fizycznego procesu zużycia, uwzględniającego wszystkie zjawiska jednocześnie, jak ma to miejsce w rzeczywistości. Na podstawie analizy mechanizmów niszczących oraz warunków pracy narzędzi w procesach kucia na półgorąco i na gorąco, wyodrębniono trzy grupy czynników wpływających na trwałość narzędzi kuźniczych. Czynniki te związane są z narzędziem (rodzaj materiału, technologia wykonania, kształt, konstrukcja, jakość wykonania), z odkuwką (rodzaj materiału, kształt, temperatura początkowa przedkuwki, jakość powierzchni, tolerancja wymiarowa) oraz z eksploatacją (parametry procesu kucia, rodzaj maszyny, zastosowana technologia kucia). Omówiono również metodę poprawy trwałości narzędzi ze szczególnym uwzględnieniem technologii wykonania warstwy wierzchniej, gdzie obecnie duże perspektywy stwarzają metody hybrydowe obróbki powierzchniowej, polegające na zastosowaniu dwóch lub więcej technik inżynierii powierzchni w jednym procesie technologicznym. Najczęściej stosowanymi warstwami hybrydowymi są warstwy typu warstwa azotowana/powłoka PVD lub CVD. Dzięki połączeniu i wzajemnemu oddziaływaniu różnych technologii można uzyskać właściwości warstwy wierzchniej nieosiągalne przy zastosowaniu tych technik oddzielnie.
This article discusses the most important mechanisms of tool destruction in forging processes, such as: abrasive wear, thermomechanical fatigue, plastic deformation, fatigue cracking, adhesive wear, and oxidation. It is shown that the intensity of wear changes when process parameters or the location on the tool change, which is determined by the time of contact between the die and forging as well as by temperature changes. The aforementioned phenomena are generally analyzed separately in the literature, and there is no precise physical description of the wear process that accounts for all of these phenomena simultaneously, just as they occur in reality. Based on analysis of destructive mechanisms and tool working conditions in semi-hot and hot forging processes, three groups of factors with an influence on the lifetime of forging tools were distinguished. These factors are related to the tool (type of material, manufacturing technology, shape, design, quality of workmanship), to the forging (type of material, shape, initial preform temperature, surface quality, dimensional tolerance) and to the forging process (forging process parameters, machine type, applied forging technology). A method for improving tool lifetime is also discussed, with particular emphasis on technology for forming the surface layer, where hybrid surface methods based on the application of two or more surface engineering techniques in one technological process are currently creating many new possibilities. The most commonly applied hybrid layers are nitrided layer/PVD or CVD coating. Thanks to the combination and reciprocal interaction of different technologies, properties of the surface layer that are not attainable when these techniques are applied separately can be achieved.
Źródło:
Obróbka Plastyczna Metali; 2015, 26, 3; 255-270
0867-2628
Pojawia się w:
Obróbka Plastyczna Metali
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Hybrid reliability modelling under general uncertainty
Autorzy:
Guo, R.
Cui, Y.
Thiart, C.
Guo, D.
Powiązania:
https://bibliotekanauki.pl/articles/2069636.pdf
Data publikacji:
2010
Wydawca:
Uniwersytet Morski w Gdyni. Polskie Towarzystwo Bezpieczeństwa i Niezawodności
Tematy:
uncertain measure
hybrid lifetime
uncertain parameter
average chance reliability
Opis:
The real world phenomena are often facing the co-existence reality of different formality of uncertainty and thus the probabilistic reliability modeling practices are very doubtful. Under complicated uncertainty environments, hybrid variable modeling is important in reliability and risk analysis, which includes Bayesian distributional theory, random fuzzy distributional theory, as well as fuzzy random distributional theory as special distribution families. In this paper, we define a new hybrid lifetime which is specified by a random lifetime distribution with an uncertain distributed parameter, which is called as random uncertain hybrid lifetime. We furthermore define the average chance distribution as a quality index for quantifying the hybrid lifetime and accordingly the average chance reliability is derived.
Źródło:
Journal of Polish Safety and Reliability Association; 2010, 1, 1; 115--122
2084-5316
Pojawia się w:
Journal of Polish Safety and Reliability Association
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Lifetime distributions with wave-like bathtub hazard
Autorzy:
Guo, R.
Thiart, C.
Cui, Y.
Guo, D.
Powiązania:
https://bibliotekanauki.pl/articles/2069543.pdf
Data publikacji:
2011
Wydawca:
Uniwersytet Morski w Gdyni. Polskie Towarzystwo Bezpieczeństwa i Niezawodności
Tematy:
lifetime distribution
hazard
bathtub hazard
likelihood function
maximum likelihood estimation
Opis:
In this paper, we argue the necessity of dealing with lifetime distributions with wave-like bathtub hazard function. Four classes of wave-like bathtub hazards are investigated. For preparing maximum likelihood estimation of the hazard parameters, the first-order and second-order partial derivatives are derived.
Źródło:
Journal of Polish Safety and Reliability Association; 2011, 2, 1; 115--122
2084-5316
Pojawia się w:
Journal of Polish Safety and Reliability Association
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Reliability concept under general uncertainty
Autorzy:
Guo, R.
Cui, Y.
Thiart, C.
Guo, D.
Powiązania:
https://bibliotekanauki.pl/articles/2069525.pdf
Data publikacji:
2010
Wydawca:
Uniwersytet Morski w Gdyni. Polskie Towarzystwo Bezpieczeństwa i Niezawodności
Tematy:
probabilistic reliability
uncertain reliability
uncertain measure
uncertainty lifetime
uncertain hazard function
Opis:
The Toyota crisis is tearing off the brand image of quality and reliability and therefore it is logical to question whether the dominating position of probability theory, on which Japanese quality and reliability engineering practices are established, should be examined. In general, reliability analysis is an exercise under uncertain environment. Foundationally speaking, uncertain modeling is a matter of choosing what kind of uncertain measure as its standing point. In this paper, we introduce the uncertainty reliability concept on the platform of the axiomatic uncertain measure theory and compare it to probabilistic reliability concept based on Kolmogorov’s probability measure theory, on which the traditional quality and reliability engineering is established. It is expecting that a foundational work can be established for a more rigorous reliability engineering and risk analysis under general uncertainty environments.
Źródło:
Journal of Polish Safety and Reliability Association; 2010, 1, 1; 105--114
2084-5316
Pojawia się w:
Journal of Polish Safety and Reliability Association
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Optimization of Operation and Safety of Baltic Port and Shipping Critical Infrastructure Network with Considering Climate-Weather Change Influence – Maximizing Lifetime in the Set of Safety States Not Worse Than a Critical Safety State
Autorzy:
Guze, S.
Kołowrocki, K.
Powiązania:
https://bibliotekanauki.pl/articles/2068746.pdf
Data publikacji:
2018
Wydawca:
Uniwersytet Morski w Gdyni. Polskie Towarzystwo Bezpieczeństwa i Niezawodności
Tematy:
critical infrastructure network
operation process
climate-weather change process
safety lifetime maximization
port
shipping
Opis:
The paper is devoted the optimization of operation process and maximization of safety lifetimes for Baltic Port and Shipping Critical Infrastructure Network (BPSCIN) at variable operation conditions related to the climateweather change. For this network, the optimal transient probabilities of BPSCIN operation process at operation states related to climate-weather change that maximize the mean value of BPSCIN safety lifetimes are found. Finally, the optimal safety and resilience indicators of considered network are presented.
Źródło:
Journal of Polish Safety and Reliability Association; 2018, 9, 1; 27--34
2084-5316
Pojawia się w:
Journal of Polish Safety and Reliability Association
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies