Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Liu, Yuwen" wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
Research on the road linear optimization design of bridge and tunnel connecting segment in the canyon
Autorzy:
Wang, Lu
Liu, Yuwen
Chen, Xiaoxin
Powiązania:
https://bibliotekanauki.pl/articles/223553.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
traffic engineering
curved road
simulation experiment
radius of curve
bridge
tunnel
traffic safety
inżynieria ruchu
łuk drogi
eksperyment symulacyjny
promień łuku
most
tunel
bezpieczeństwo na drodze
Opis:
It is easy to skid and roll by centrifugal force and wind, which affects the safety of the vehicle. At the same time, the special location of bridge and tunnel connecting segment in the canyon will accelerate the wind, and make the transverse wind play a more important role in driving vehicles. Based on the acceleration effect of canyons on wind, the vehicle model is simulated by Carsim software, and the road and wind models are established. It is studied that the vehicle has different radius of circular curve under different wind levels, corresponding to different superelevation. The lateral acceleration, lateral deflection and transverse force coefficient are selected as the running state of the vehicle at different speeds to research the linear optimization design of bridge and tunnel connecting segment in the canyon. The result shows that when the wind force exceeds the fifth grade, it is possible for the vehicle to overturn under the limit minimum radius required by the standard value. In order to ensure the stability and safety of the vehicle, this paper considers the geographical position of bridge and tunnel connecting segment in the canyon and the relationship between the radius of the superelevation and circular curve. What’s more, it puts forward the optimal limit minimum radius of the circular curve with different wind grades of 5-9 grades. At the same time, when the road alignment cannot be optimized under the condition, this paper puts forward the speed limit that the vehicle safety can be guaranteed under different wind speed conditions. The speed limit can provide reference for traffic management and safety guarantee of mountain expressway.
Źródło:
Archives of Transport; 2019, 52, 4; 81-93
0866-9546
2300-8830
Pojawia się w:
Archives of Transport
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Die Wall Lubrication on High Velocity Compaction Behavior and Sintering Properties of Fe-Based PM Alloy
Autorzy:
Liu, Zili
Li, Dong
Liu, Xiqin
Li, Haohao
Huang, Xin
Tang, Zhihao
Zou, Yuwen
Powiązania:
https://bibliotekanauki.pl/articles/352101.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
high velocity compaction
die wall lubrication
green density
impact force
cold welding
Opis:
Fe-based PM alloy powder of Fe-2.5Ni-0.5Mo-2Cu-0.4C was pressed by high velocity compaction combined with die wall lubrication, and the effect of die wall lubrication on high velocity compaction behavior and sintering properties of the Fe-based PM alloy were studied. The results indicate that the impact force, green density, sintered density of samples increase with the augment of the impact velocity and die wall lubrication. Compared with that without die wall lubrication, the green density and sintered density of the sample with die wall lubrication are about 0.07-0.12 g/cm3 and 0.08~0.11 g/cm3 higher at the same impact velocity, respectively, while the ejection force of the die wall lubricated sample is much smaller, and reduced about 26%~36%. The green compact with die wall lubrication has much fewer porosity than that without die wall lubrication, and more mechanical bonding and cold welding regions are observed. The sintered samples mainly consists of gray pearlite and white ferrite, and more pearlite is observed in the sintered sample with die wall lubrication.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 2; 677-684
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies