Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Kalandyk, B." wg kryterium: Autor

  Lista filtrów
Wyrównaj
Wyświetlanie 1-15 z 25
Tytuł:
Microstructure and abrasive wear resistance of 18Cr-4Ni-2.5Mo cast steel
Autorzy:
Kalandyk, B.
Powiązania:
https://bibliotekanauki.pl/articles/380296.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stal wysokostopowa Cr-Ni
mikrostruktura
wykres CTPc
zużycie ścierne
highly alloyed Cr-Ni cast steel
microstructure
equivalent Cr and Ni
CCT diagrams
abrasive wear
Opis:
An influence of a decreased Cr content on the microstructure of the highly alloyed Cr-Ni cast steel, duplex type, melted under laboratory conditions, was characterized in the paper. The microstructure investigations were performed in the initial state and after the heat treatment (solution annealing) at 1060 C as well as the phase transformation kinetics at continuous cooling was measured. The wear resistance of the investigated cast steel was tested and compared with the 24%Cr-5%Ni-2.5%Mo cast steel. The Cr content decrease, in ferritic-austenitic cast steels (duplex), from 24-26%Cr to 18% leads to the changes of the castings microstructure and eliminating of a brittle \sigma phase. In dependence of the casting cooling rate, apart from ferrite and austenite, also fine martensite precipitates occur in the casting structure. It was shown that the investigated cast steel is characterised by a slightly lower wear resistance than the typical cast steel duplex grades.
Źródło:
Archives of Foundry Engineering; 2012, 12, 4; 81-84
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wear resistance of 18%Cr-9%Ni steel used for cast parts of pumps operating in corrosive – erosive environments
Odporność na zużycie staliwa 18%Cr-9%Ni stosowanego na elementy pomp pracujących w warunkach korozyjno-erozyjnych
Autorzy:
Kalandyk, B.
Powiązania:
https://bibliotekanauki.pl/articles/354664.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenic steel
cast steel
Miller test
slury abrasiv resistance
microstructure
stal austenityczna
staliwo
test Millera
odporność na ścieranie
mikrostruktura
Opis:
This paper presents the results of experimental studies, the main aim of which has been to demonstrate that changes in the microstructure of austenitic 18%Cr-9%Ni cast steel provoked by the addition of 1.4% boron, and boron with titanium, give increased wear resistance. After melting the high-alloyed 18%Cr-9%Ni cast steel with an addition of boron, and boron with titanium, metallographic examinations were conducted using light microscopy and SEM. These examinations revealed in the austenitic structure of the 18%Cr-9%Ni cast steel, the presence of a eutectic rich in boron and chromium, and characterised by a microhardness of 1838-1890 μ HV20 . Additionally, in the cast steel inoculated with boron and titanium, the presence of titanium nitride precipitates was observed. Changes that have occurred in the microstructure as a result of introducing the additions of boron, and boron with titanium, also caused an increase of the cast steel hardness from 212 HV30 to 290-320 HV30 and 320-350 HV30, respectively. To determine the abrasive wear resistance, 16-hour Miller test was performed (ASTM G 75-07), wherein the abrasive medium was a mixture of SiC and water. Obtaining the hard, rich in boron and chromium, eutectic and titanium nitride precipitates in the structure of 18%Cr-9%Ni cast steel increased the abrasive wear resistance by approximately 21%, according to the data recorded in the sixteenth hour of the test cycle. As an additional benchmark point for the results obtained served the wear resistant, structural, L35GSM steel used for castings working in difficult conditions. Comparing the values of abrasive wear resistance obtained for the 18%Cr-9%Ni cast steel and cast L35GSM steel, an increase in the wear resistance of the 18%Cr-9%Ni cast steel by about 35% has been proved.
W artykule przedstawiono wyniki badań eksperymentalnych, których celem było wykazanie, że zmiany w mikrostrukturze austenitycznego staliwa 18%Cr-9%Ni na skutek wprowadzenie dodatku 1,4% boru oraz boru i tytanu skutkują zwiększeniem odporności na zużycie. Po wytopieniu wysokostopowego staliwa 18%Cr-9%Ni z borem oraz z dodatkiem boru i tytanu przeprowadzono badania metalograficzne z wykorzystaniem mikroskopu świetlnego i skaningowego. Badania te wykazały obecność w austenitycznej strukturze staliwa 18%Cr-9%Ni eutektyki bogatej w bor i chrom, o mikrotwardosci 1838-1890 μHV20: W staliwie modyfikowanym borem i tytanem dodatkowo stwierdzono obecność wydzieleń azotków tytanu. Zmiany jakie zaszły w mikrostrukturze po wprowadzeniu dodatków boru oraz boru i tytanu spowodowały również wzrost twardości staliwa z 212 HV30 odpowiednio do 290-320 HV30 oraz do 320-350 HV30 . Do określenia odporności na zużycie ścierne wykonano 16-godzinny test Millera (ASTM G 75-07), w którym medium ścierającym była mieszanina SiC i wody. Uzyskanie twardej eutektyki bogatej w bor i chrom oraz wydzieleń azotków tytanu w strukturze staliwa 18%Cr-9%Ni doprowadziło do zwiększenia odporności na ścieranie o około 21% w 16 godzinie cyklu badań. Dodatkowym punktem odniesienia uzyskanych wyników było odporne za zużycie, konstrukcyjne staliwo L35GSM stosowane na odlewy pracujące w trudnych warunkach. Porównując otrzymane wyniki odporności na zużycie ścierne staliwa 18Cr-9%Ni oraz staliwa L35GSM wykazano, wzrost odporności na zużycie staliwa 18%Cr-9%Ni o około 35%.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 3; 841-844
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of steel - applied for large-dimension castings for the power engineering - refining in the ladle-furnace
Efekty rafinacji w pieco-kadzi stali stosowanej na wielkogabarytowe odlewy dla energetyki
Autorzy:
Kalandyk, B.
Wojtal, W
Powiązania:
https://bibliotekanauki.pl/articles/355926.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cast steel for power industry
melting technology
electric arc furnace
ladle furnace
desulphurisation
staliwa dla energetyki
technologia topienia
elektryczny piec łukowy
piecokadź
odsiarczanie
Opis:
The changes of a sulphur content during refining in melting low-alloy and high-alloy steels (G17CrMoV5-10; GX12CrMoNiVNbN9-1) applied for large-dimension castings for the power engineering are presented in the hereby paper. The investigated steel was melted in the oxygen-recovery melting technology with an application of maximum 70% of the process scrap. In addition, after steel melting in the electric arc furnace (EAF), the secondary metallurgy was performed in the ladle furnace (LF). It was shown that the application of the secondary metallurgy by a synthetic slag in the ladle furnace and argon bubbling of a metal bath leads to obtaining in the final analysis: 0.0043-0.0046% of sulphur (a decrease of S content during refining in LF reached 40%). Current measurements of FeO in the slag and maintaining its content below 0.8%, support obtaining such low sulphur content in steel. So low level of the slag oxidizing is one of the necessary conditions for a deep desulphurisation of the metal bath. Without the secondary metallurgy the sulphur content in low-alloy cast steel was 0.007%, while 0.01% in high-alloy cast steel. Controlling of the gas (oxygen, nitrogen) content during steel melting and correcting the amount of additions (e.g. deoxidants), allowed to obtain the low oxygen content (below 45 ppm for two investigated steel grades) and nitrogen content (88 ppm for low-alloy steel and 330 ppm for high-alloy steel), which warrants a good combination of strength and plastic properties.
W pracy przedstawiono zmiany zawartosci siarki podczas rafinacji w czasie wytapiania stali nisko- i wysokostopowej (G17CrMoV5-10; GX12CrMoNiVNbN9-1) stosowanej na wielkogabarytowe odlewy dla energetyki. Badana stal wytopiono w technologii odzyskowo-tlenowej z zastosowaniem maksymalnie 70% złomu własnego. Dodatkowo, po wytopieniu stali w piecu łukowym (EAF) przeprowadzono obróbke pozapiecowa w pieco-kadzi (LF). Wykazano, ze zastosowanie obróbki pozapiecowej zuzlem syntetycznym w pieco-kadzi i argonowania kapieli metalowej prowadzi do uzyskania w analizie koncowej 0,0043-0,0046%S (zmniejszenie zawartosci S podczas rafinacji w LF siegało 40%). Uzyskaniu tak niskiej zawartosci siarki w stali sprzyja m.in. biezacy pomiar FeO w zuzlu i utrzymanie jego zawartosci ponizej 0,8%. Tak niski poziom stopnia utlenienia zuzla jest jednym z warunków koniecznym do dobrego odsiarczenia kapieli metalowej. Bez obróbki pozapiecowej zawartosc siarki w staliwie niskostopowym wynosiła 0,007%, natomiast dla staliwa wysokostopowego 0,01%. Kontrola zawartosci gazów (tlenu i azotu) w czasie wytapiania stali i dokonywana korekta ilosci wprowadzanych dodatków (np. odtleniaczy) doprowadziła do uzyskania niskiej zawartosci tlenu (ponizej 45 ppm dla dwóch badanych gatunków stali) i azotu (88 ppm dla stali niskostopowej, 330 ppm dla stali wysokostopowej) gwarantujaca dobra kombinacje własciwosci wytrzymałosciowych i plastycznych odlewów.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 3; 779-783
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effects of Rare Earth Metal Addition on Wear Resistance of Chromium-Molybdenum Cast Steel
Autorzy:
Kasińska, J.
Kalandyk, B.
Powiązania:
https://bibliotekanauki.pl/articles/381581.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
wear resistant alloys
cast steel
rare earth metals
Miller test
surface profile
stopy odporne na zużycie
stal
metale ziem rzadkich
test Millera
profil powierzchni
Opis:
This paper discusses changes in the microstructure and abrasive wear resistance of G17CrMo5-5 cast steel modified with rare earth metals (REM). The changes were assessed using scanning microscopy. The wear response was determined in the Miller test to ASTM G75. Abrasion tests were supplemented with the surface profile measurements of non-modified and modified cast steel using a Talysurf CCI optical profilometer. It was demonstrated that the modification substantially affected the microstructure of the alloy, leading to grain size reduction and changed morphology of non-metallic inclusions. The observed changes in the microstructure resulted in a three times higher impact strength (from 33 to 99 kJ/cm2) and more than two times higher resistance to cracking (from 116 to 250 MPa). The following surface parameters were computed: Sa: Arithmetic mean deviation of the surface, Sq: Root-mean-square deviation of the surface, Sp: Maximum height of the peak, Sv: Maximum depth of the valley, Sz: Ten Point Average, Ssk: Asymmetry of the surface, Sku: Kurtosis of the surface. The findings also indicated that the addition of rare earth metals had a positive effect on the abrasion behaviour of G17CrMo5-5 cast steel.
Źródło:
Archives of Foundry Engineering; 2017, 17, 3; 63-68
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of high-manganese cast steel strain hardening on the abrasion wear resistance in a mixture of SiC and water
Autorzy:
Kalandyk, B.
Zapała, R.
Powiązania:
https://bibliotekanauki.pl/articles/382258.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenite
high-manganese steel
microstructure
abrasive wear resistance
Miller slurry machine test
austenit
stal wysokomanganowa
mikrostruktura
odporność na zużycie ścierne
test Millera
Opis:
The study attempts to determine the impact of the high-manganese cast steel strain hardening on its abrasion wear resistance in a mixture of SiC and water prepared in accordance with ASTM G75. For tests, the high-manganese cast steel containing 10.7, 17.9 and 20.02% Mn was selected. The results of microstructure examinations and abrasion wear resistance tests carried out on the material in non-hardened condition and after strain hardening with a force of 539.55kN were disclosed. Additionally, the surface of samples after a 16-hour cycle of abrasion tests was examined. Moreover, based on the obtained results, the effect of different contents of Mn in cast steel was studied, mainly in terms of its impact on the abrasion wear resistance. The results obtained on the tested materials were compared with the results obtained on the low-alloyed abrasion wear-resistant cast steel L35GSM.
Źródło:
Archives of Foundry Engineering; 2013, 13, 4; 63-66
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Surfacing 24Cr-5Ni-2.5Mo Duplex Steel Castings by TIG
Autorzy:
Kasinska, J.
Skrzypczyk, A.
Kalandyk, B.
Powiązania:
https://bibliotekanauki.pl/articles/379970.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
duplex cast steel
surfacing
Tungsten Inert Gas method
solution heat treatment
microstructure change
staliwo duplex
proces napawania
metoda TIG
obróbka cieplna
Opis:
This article discusses the influence of Tungsten Inert Gas (TIG) surfacing of duplex cast steel on its hardness and structure. The samples of 24Cr-5Ni-2.5Mo ferritic-austenitic cast steel were subjected to single-overlay processes with the use of solid wire having the chemical composition similar to that of the duplex cast steel. As a result of the surfacing, the welds were obtained that had no welding imperfections with a smooth transition to the base material. In the test without the heat treatment, directly below the fusion line, we observe a ferrite band with a width of approximately 200 μm without visible austenite areas. Some of the samples were then solution treated (1060°C). Both variants, without and after solution heat treatment, were subjected to testing. Significant changes in the microstructure of the joint were observed after the heat treatment process (heat affected zone and weld microstructure changes). In both areas, an increase in the austenite volume fraction after solution heat treatment was observed. Changes in the microhardness of the ferrite in the HAZ area directly below the fusion line were also observed.
Źródło:
Archives of Foundry Engineering; 2018, 18, 2; 15-20
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ żużli syntetycznych na proces odsiarczania niskostopowego staliwa Cr-Ni-Mo
The Influence of Synthetic Slags on Desulphurisation Process of Low Alloy Cr-Ni-Mo Cast Steel
Autorzy:
Balicki, M.
Sobula, S.
Kalandyk, B.
Powiązania:
https://bibliotekanauki.pl/articles/380598.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
obróbka pozapiecowa stali
żużel syntetyczny
staliwo Cr-Ni-Mo
secondary metallurgy
synthetic slag
Cr-Ni-Mo cast steel
Opis:
W artykule zaprezentowano wyniki obróbki pozapiecowej stali niskostopowej L70H2GNM przeznaczonej na masywne odlewy, pracujące w warunkach ścierania. Obróbka polegała na przedmuchiwaniu argonem stali w kadzi odlewniczej o pojemności 8,5 Mg, przy udziale trzech różnych żużli syntetycznych. Do badań wybrano żużle dostępne na rynku materiałów odlewniczych takie jak: LDSF LT firmy Kerneos, UZRA KP firmy ZM Ropczyce, który dodatkowo zmodyfikowano przez wprowadzenie aluminium. Czas przedmuchiwania kąpieli argonem wynosił 4 minuty dla każdego wytopu. Na podstawie przeprowadzonych badań uzyskano zmiany zawartości siarki w wytapianym staliwie w zależności od zastosowanych żużli syntetycznych. Stwierdzono, że zawartość siarki w staliwie zmniejszyła się po rafinacji w kadzi. Dodatkowo wykazano, że na zawartość siarki w badanym staliwie ma wpływ skład chemiczny zastosowanych żużli syntetycznych.
In this article, the results of secondary metallurgy of L70H2GNM cast steel has been shown. This grade of low alloy cast steel is popular in Poland for heavy castings which works in wear conditions e.g. in coal mills. The ladle refining process was composed of argon stirring in 8.5 Mg bottom pour ladle and treatment with synthetic slags. The three commercial slag mixtures available on casting materials market such as: LDSF of the Kerneos company, UZRA KP and UZRA KP+Al of the ZM Ropczyce company were chosen for examinations. The time of argon blowing through porous plug was 4 minutes for every melt. Experimental results have shown, that sulphur content in steel decreases after refining in ladle. Moreover, desulphurisation ratio during argon stirring have also been influenced by composition of slag mixtures.
Źródło:
Archives of Foundry Engineering; 2015, 15, 4 spec.; 11-14
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of Si and Mn on Microstructure and Selected Properties of Cr-Ni Stainless Steels
Autorzy:
Kalandyk, B.
Zapała, R.
Starowicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/380853.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cast stainless
alloy composition
hardness
electrochemical corrosion
Miller test
odlew ze stali nierdzewnej
skład stopu
twardość
korozja elektrochemiczna
test Millera
Opis:
Cast stainless steel of the Cr-Ni duplex type is used, among others, for the cast parts of pumps and valves handling various chemically aggressive media. Therefore, the main problem discussed in this article is the problem of abrasion wear resistance in a mixture of SiC and water and resistance to electrochemical corrosion in a 3% NaCl- H2O solution of selected cast steel grades, i.e. typical duplex cast steel, high silicon and manganese duplex cast steel, and Cr-Ni austenitic cast steel (type AISI 316L). The study shows that the best abrasion wear resistance comparable to Ni-Hart cast iron was obtained in the cast duplex steel, where Ni was partially replaced with Mn and N. This cast steel was also characterized by the highest hardness and matrix microhardness among all the tested cast steel grades. The best resistance to electrochemical corrosion in 3% NaCl- H2O solution showed the cast duplex steel with high content of Cr, Mo and N. The addition of Ni plays rather insignificant role in the improvement of corrosion resistance of the materials tested.
Źródło:
Archives of Foundry Engineering; 2017, 17, 1; 192-196
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics of centrifugally cast GX25CrNiSi18-9 steel
Autorzy:
Zapała, R.
Kalandyk, B.
Rakowska, A.
Powiązania:
https://bibliotekanauki.pl/articles/381343.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
metallography
heat resistance
cast steel
metalografia
żaroodporność stopu
staliwo
Opis:
The paper presents the results of microstructural examinations of the industrial heat-resistant centrifugally cast GX25CrNiSi18-9 steel characterised by increased content of Cu. The study included changes in the microstructure of base cast steel respective of the steel held at a temperature of 900 and 950°C for 48 hours. Based on the results obtained, an increase in microhardness of the examined cast steel matrix with increasing temperature was stated, which was probably caused by fine precipitates enriched in Cr, Mo, and C forming inside the matrix grains. The layer of scale formed on the tested cast steel oxidised in the atmosphere of air at 900 and 950°C was characterised by an increased tendency to degradation with increasing temperature of the conducted tests.
Źródło:
Archives of Foundry Engineering; 2011, 11, 3 spec.; 249-254
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Comparison of Microstructure and Mechanical Properties of Cast Steel Carried out on Cast-on Samples and Samples Cast Separately
Autorzy:
Kalandyk, B. E.
Zapała, R. E.
Powiązania:
https://bibliotekanauki.pl/articles/1837717.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
cast steel
cast-on samples
heat treatment
mechanical properties
metallography
staliwo
próbki odlewu
obróbka cieplna
właściwości mechaniczne
metalografia
Opis:
The results of microstructure examinations and UTS, YS, El, RA carried out on low-carbon cast steel containing 0.15% C. The tests were carried out on specimens cut out from samples cast on a large-size casting and from samples cast in separate foundry moulds. It has been shown that significant differences in grain size observed in the material of the separately cast samples and cast-on samples occur only in the as-cast. In the as-cast state, in materials from different tests, both pearlite percent content in the structure and mean true interlamellar spacing remain unchanged. On the other hand, these parameters undergo significant changes in the materials after heat treatment. The mechanical properties (after normalization) of the cast-on sample of the tested cast steel were slightly inferior to the values obtained for the sample cast in a separate foundry mould. The microscopic examinations of the fracture micro-relief carried out by SEM showed the presence of numerous, small non-metallic inclusions, composed mainly of oxide-sulphides containing Mn, S, Al, Ca and O, occurring individually and in clusters.
Źródło:
Archives of Foundry Engineering; 2021, 21, 2; 81-88
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Odporność korozyjna dwufazowego staliwa 24Cr-5Mn-2Ni-3Mo
Corrosion Resistance of 24Cr-5Mn-2Ni-3Mo Duplex Cast Steel
Autorzy:
Kalandyk, B.
Starowicz, M.
Zapała, R.
Powiązania:
https://bibliotekanauki.pl/articles/382698.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
staliwo duplex
korozja elektrochemiczna
krzywe polaryzacji
duplex cast steel
electrochemical corrosion
polarization curves
Opis:
Przedmiotem badań było porównanie odporności na korozję elektrochemiczną dwóch gatunków kwasoodpornego staliwa ferrytyczno-austenitycznego (duplex): klasycznego zawierającego 24Cr-5Ni-2,5Mo-2,6Cu z nowym gatunkiem staliwa zawierającym 24Cr-5Mn-2Ni-3Mo, w którym Ni częściowo został zastąpiony przez Mn i N. Zawartość pierwiastków austenitotwórczych (Ni, Mn i N) została tak dobrana, aby udział ferrytu δ w staliwie wynosił 45÷50%. Na podstawie przeprowadzonych badań korozyjnych stwierdzono, że oba materiały ulegają samorzutnej pasywacji w 3% roztworze NaCl. Staliwo z podwyższoną zawartością Mn i N posiada znacznie wyższą wartość potencjału bezprądowego (Eo = -0,7 V), niż klasyczne staliwo duplex (Eo = -0,95V) oraz wykazuje zasadnicze różnice w gęstości prądu anodowego. Jest ono również bardziej odporne na korozję lokalną. Analiza mikrostrukturalna produktów korozji wskazuje na obecność nielicznych wżerów korozyjnych powstających głównie na wtrąceniach niemetalicznych.
The aim of the studies was to compare the electrochemical corrosion resistance of the two grades of acid-resistant cast austenitic-ferritic (duplex) steel, i.e. the conventional grade containing 24Cr-5Ni-2.5Mo-2.6Cu and a cast steel grade containing 24Cr-5Mn-2Ni-3Mo, where Ni was partially replaced by a higher content of Mn and N. The content of austenite-forming elements (Ni, Mn and N) has been chosen in such a way as to keep the δ ferrite fraction in the cast steel at a level of 45 ÷ 50%. Based on the corrosion test results, it was found that both materials undergo a spontaneous passivation in the 3% NaCl solution. The cast steel with increased content of Mn and N has a much higher value of the electro less potential (Eo = -0.7 V) than the conventional cast duplex steel (Eo = -0,95V), and shows substantial differences in the anodic current density. It is also more resistant to local corrosion. Microstructural analysis of corrosion products indicates the presence of very few corrosion pits formed mainly on the non-metallic inclusions.
Źródło:
Archives of Foundry Engineering; 2015, 15, 4 spec.; 53-56
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Tempering Temperature on the Mechanical Properties of Cast L35HM Steel
Autorzy:
Zapała, R.
Kalandyk, B.
Wawro, P.
Powiązania:
https://bibliotekanauki.pl/articles/380169.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat treatment
mechanical properties
cast L35HM steel
tempering
quenching
obróbka cieplna
właściwości mechaniczne
odlewy ze stali
Opis:
A possibility to control the strength, hardness and ductility of the L35HM low-alloy structural cast steel by the applied tempering temperature is discussed in the paper. Tests were carried out on samples taken from the two randomly selected industrial melts. Heat treatment of the cast samples included quenching at 900°C, cooling in an aqueous solution of polymer, and tempering at 600 and 650°C. The obtained results showed that the difference in the tempering temperature equal to 50°C can cause the difference of 121 MPa in the values of UTS and of 153 MPa in the values of 0.2%YS. For both melts tempered at 600 °C, the average values of UTS and 0.2%YS were equal to 995 MPa and 933 MPa, respectively. The values of EL and RA did not show any significant differences. Attention was drawn to large differences in strength and hardness observed between the melts tempered at 600 and 650°C. Despite differences in the mechanical properties of the examined cast steel, the obtained results were superior to those specified by the standard.
Źródło:
Archives of Foundry Engineering; 2017, 17, 2; 151-156
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Heat Treatment on the Microstructures 20%Cr-21%Ni-5%Si Cast Steel
Autorzy:
Kalandyk, B.
Kasińska, J.
Olejnik, E.
Powiązania:
https://bibliotekanauki.pl/articles/381678.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austenitic cast steel
stainless steel
cast steel microstructure
heat treatment
staliwo austenityczne
stal nierdzewna
mikrostruktura staliwa
obróbka termiczna
Opis:
The study describes the effect of heat treatment on the microstructure of cast high-alloyed 20%Cr-21%Ni-5%Si steel. It has been found that the microstructure of the tested material in the initial state consists of an austenitic matrix and precipitates rich in Si, Cr, Ni and Mn, characterized by different morphology and distributed mainly along the grain boundaries. The conducted heat treatment (after solutioning at: 1060, 1100 and 1200ºC) has changed both morphology and chemical composition of the precipitates. Significant reduction in the Si and Ni content and slight increase in the Cr content, especially after solutioning at 1200°C, combined with a simultaneous decrease in the hardness of the precipitates was evidenced.
Źródło:
Archives of Foundry Engineering; 2015, 15, 2 spec.; 39-42
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of CaSiAl Modification on the Non-metallic Inclusions and Mechanical Properties of Low-carbon Microalloyed Cast Steel
Autorzy:
Kalandyk, B.
Zapała, R.
Sobula, S.
Tęcza, G.
Powiązania:
https://bibliotekanauki.pl/articles/382745.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
microalloyed cast steel
microstructure
mechanical property
non-metallic inclusions
staliwo mikrostopowe
mikrostruktura
właściwości mechaniczne
wtrącenia niemetaliczne
Opis:
The effect of CaSiAl modification (43-49% Ca, 43-48% Si, 2% Al) on the non-metallic inclusions and mechanical properties of cast low-carbon steel is discussed. Tests were carried out on the cast steel with 0.2% C and micro-additives of V and Nb, used mainly for heavy steel castings (e.g. slag ladles). The modifier in an amount of 1.5 and 3 kg / Mg was introduced to the liquid steel before tapping the metal into a ladle. Test ingots of Y type and a weight of 10 kg were cast and then subjected to a normalizing heat treatment. Using light microscopy and scanning electron microscopy, qualitative and quantitative evaluation of the non-metallic inclusions present in as-cast samples was carried out. Additionally, tests of mechanical strength and impact strength were performed on cast steel with and without the different content of modifier. It was found that increasing the modifier addition affected impact strength but had no significant effect on tensile strength and yield strength. The material with high impact strength had the smallest area fraction of non-metallic inclusions in the microstructure (0.20%). The introduction of modifiers changed the morphology of non-metallic inclusions from dendritic to regular and nodular shapes.
Źródło:
Archives of Foundry Engineering; 2019, 1; 47-52
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Silicon Addition on the Microstructure of Cast 24Cr-5Ni-2.5Mo-xSi Duplex Steel
Autorzy:
Kalandyk, B.
Zapała, R.
Witkowska, M.
Kowalska, J.
Powiązania:
https://bibliotekanauki.pl/articles/381193.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stainless steels
microstructure of cast
Thermo-Calc
duplex steel
stale nierdzewne
mikrostruktura odlewu
stal duplex
Opis:
Characteristics of the microstructure of corrosion-resistant cast 24Cr-5Ni-2.5Mo duplex steel after introduction of 0.98, 1.67 and 4.3% Si were described. Based on the test results it has been found that silicon addition introduced to the corrosion-resistant cast two-phase duplex steel significantly reduces austenite content in the alloy matrix. Increasing silicon content in the test alloy to 4.3% has resulted, in addition to the elimination of austenite, also in the precipitation of Si-containing intermetallic phases at the grain boundaries and inside the grains. The precipitates were characterized by varying content of Cr and Mo, indicating the presence in the structure of more than one type of the brittle phase characteristic for this group of materials. The simulation using Thermo-Calc software has confirmed the presence of ferrite in all tested alloys. In the material containing 4.3% Si, the Cr and Si enriched precipitates, such as G phase and Cr3Si were additionally observed to occur.
Źródło:
Archives of Foundry Engineering; 2018, 18, 1; 186-190
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Wyświetlanie 1-15 z 25

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies