Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "insertion loss" wg kryterium: Temat


Wyświetlanie 1-2 z 2
Tytuł:
Solution of some problems of single-scale wavelet transform processor using a magnetostatic surface wave device
Autorzy:
Lu, W.
Kuang, L.
Lü, X.
Zhu, C.
Zhang, T.
Zhang, J.
Powiązania:
https://bibliotekanauki.pl/articles/221174.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
wavelet transform processor
magnetostatic surface wave (MSSW)
interdigital transducer
direct coupling
insertion loss
Opis:
In this paper, we investigate the implementation schemes of a single-scale wavelet transform processor using magnetostatic surface wave (MSSW) devices. There are three implementation schemes: the interdigital transducer, the meander line transducer and the grating transducer. Because the interdigital transducer has excellent properties, namely, good frequency characteristic and low insertion loss, we use the interdigital transducer as the implementation scheme of a single-scale wavelet transform processor using MSSW device. In the paper, we also present the solutions to the three key problems: the direct coupling between the input transducer and the output transducer, the insertion loss, and the loss characteristics of the gyromagnetic film having an influence on the wavelet transform processor. There are two methods of reducing the direct coupling between the input transducer and the output transducer: increasing the distance between the input transducer and the output transducer, and placing a metal "wall" between the input transducer and the output transducer. There also are two methods of reducing the insertion loss of a single-scale wavelet transform processor using a MSSW device for scale: the appropriate thickness of the yttrium iron garnet (YIG) film and the uniform magnetic field. The smaller the ferromagnetic resonance linewidth of the gyromagnetic film, the smaller the magnetostatic wave propagation loss.
Źródło:
Metrology and Measurement Systems; 2012, 19, 4; 685-692
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of gold electrodes on the properties of shear horizontal acoustic plate mode viscosity sensor in Bt-cut quartz
Wpływ złotych elektrod na właściwości czujnika z poprzecznym horyzontalnym akustycznym modem płytowym w kwarcu o orientacji BT
Autorzy:
Soluch, W.
Łysakowska, M.
Wróbel, T.
Powiązania:
https://bibliotekanauki.pl/articles/192343.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Technologii Materiałów Elektronicznych
Tematy:
shear horizontal acoustic plate modes
BT-cut quartz
gold electrodes
delay line
insertion loss
viscosity sensor
poprzeczne horyzontalne akustyczne mody płytowe
kwarc o orientacji BT
złote elektrody
linia opóźniająca
tłumienność wtrącenia
czujnik lepkości
Opis:
Until now the influence of gold electrodes on the properties of shear horizontal acoustic plate modes (SHAPMs) in BT-cut quartz (-50.5°YX90°) was never before calculated or measured. Calculation presented in this study show that the amplitude of mechanical motion at the quartz plate surface decreases with an increase of the thickness of the gold layer. When the thickness of the gold layer is increased only on one side of the quartz plate, the amplitude decreases on the same side, whereas it remaines unchanged on the opposite side. For one of the SHAPMs, the amplitude of mechanical motion become about twice as big when the gold layer thickness increased from about 0.1 μm to 1 μm. This effect was confirmed by the measurements of the changes of the delay line insertion loss against viscosity of glycerine and water solutions.
Po raz pierwszy wykonano obliczenia i pomiary wpływu złotych elektrod na właściwości czujnika lepkości z poprzecznym horyzontalnym akustycznym modem płytowym (PHaMP) w kwarcu o orientacji BT (-50.5°YX90°). stwierdzono, że amplituda drgań mechanicznych na powierzchni płytki kwarcowej maleje wraz ze wzrostem grubości warstwy złota. Gdy grubość warstwy złota wzrasta po jednej stronie płytki kwarcowej, to zmniejszanie ma miejsce po tej samej stronie, podczas gdy pozostaje niezmienione po stronie przeciwnej. Dla jednego z PHaMP, amplituda drgań mechanicznych zmalała dwa razy gdy grubość warstwy złota wzrosła od 0,1 μm do 1 μm. Efekt ten został potwierdzony przez pomiar zmian tłumienności linii opóźniającej w funkcji lepkości roztworów gliceryny i wody.
Źródło:
Materiały Elektroniczne; 2017, T. 45, nr 2-4, 2-4; 3-5
0209-0058
Pojawia się w:
Materiały Elektroniczne
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies