Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "zwilzalnosc" wg kryterium: Temat


Tytuł:
An effect of aromatic diluent addition on the selected properties of epoxy resin
Wpływ dodatku rozcieńczalnika aromatycznego na wybrane właściwości żywicy epoksydowej
Autorzy:
Hutera, B.
Drożyński, D.
Powiązania:
https://bibliotekanauki.pl/articles/263970.pdf
Data publikacji:
2005
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
kąt zwilżania
zwilżalność
spoiwo
contact angle
wettability
binder
Opis:
The article describes the studies which have been conducted on the dynamic wetting of quartz grains by EPIDIAN 5 resin and by this resin with an addition of 5 wt. %, 20 wt. % and 30 wt. % of xylene at different temperatures. In the case of the investigated resin, the wetting process dynamics is best described by a logarithmic function: theta = A Int + B0, where: theta is the contact angle after time t, and A and B0 are constants characteristic of this process at a given temperature. It has been proved that with 5 wt. % addition of xylene both constants assume a value different than zero. With addition of 20 wt. % and 30 wt. % of xylene, the State of equilibrium is reached almost immediately, and it is expressed by a zero value of constant A. The infrared spectroscopy did not reveal the presence of any chemical reactions between the EPIDIAN 5 resin and xylene, thus confirming that the chemical structure of xylene molecule affects the type of interaction and proves the non-active behaviour of xylene as a diluent. The importance of the studies for foundry sand practice has been stressed.
W artykule przedstawiono badania dynamiki zwilżania kwarcu przez żywicę EPIDIAN 5 z dodatkiem 5% wag., 20% wag. i 30% wag. ksylenu w różnych temperaturach. Dla przebadanej żywicy, proces dynamiki zwilżania najlepiej opisuje funkcja logarytmiczna: theta = - A Int + B0, gdzie: theta jest kątem zwilżania po czasie t, zaś A i B0 stałymi charakteryzującymi proces w danej temperaturze. Wykazano, że wartość obydwu stałych przy dodatku 5% wag. ksylenu jest różna od zera. Przy dodatku 20% wag. i 30% wag. uzyskuje się praktycznie natychmiastowy stan równowagi, któremu odpowiada zerowa wartość stałej A. Badania spektroskopowe w podczerwieni nie wykazały reakcji chemicznej pomiędzy żywicą EPIDIAN 5 a ksylenem, potwierdzając tym samym wpływ struktury chemicznej cząsteczki ksylenu na rodzaj oddziaływań i jego nieaktywny charakter jako rozcieńczalnika. Podkreślono wpływ przeprowadzonych badań dla praktyki mas formierskich.
Źródło:
Metallurgy and Foundry Engineering; 2005, 31, 2; 175-184
1230-2325
2300-8377
Pojawia się w:
Metallurgy and Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The influence of physical and chemical parameters of modified water glass on the strength of loose self-setting sands with water glass
Wpływ parametrów fizykochemicznych zmodyfikowanego szkła wodnego na wytrzymałość mas samoutwardzalnych ze szkłem wodnym
Autorzy:
Kmita, A.
Hutera, B.
Powiązania:
https://bibliotekanauki.pl/articles/264164.pdf
Data publikacji:
2012
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
lepkość
zwilżalność
modyfikacja
szkło wodne
viscosity
wettability
modification
water glass
Opis:
An attempt of water glass modifying by 30% water bochmite Al(OH)O solution was undertaken. The flow curves were determined and the binder viscosity estimated from them. The quartz wettability by binders was determined by measuring the wetting angle θ changes with time. Strength properties of moulding sands with fractions of modified binders were verified by checking the tensile strength [formula] after various hardening times under environmental conditions. The [formula] value after 24 h of hardening was assumed for the analysis.
W artykule opisano próbę modyfikacji szkła wodnego, trzydziestoprocentowym wodnym roztworem bemitu Al(OH)O. Wyznaczono krzywe płynięcia, z których określono lepkość spoiw. Zwilżalność kwarcu przez spoiwa określono, badając zmiany wartości kąta zwilżania θ w czasie. Właściwości wytrzymałościowe mas z udziałem spoiw modyfikowanych weryfikowano, badając wytrzymałość na rozciąganie [wzór] po różnych czasach utwardzania w warunkach otoczenia. Do analizy przyjęto [wzór] po 24 h utwardzania.
Źródło:
Metallurgy and Foundry Engineering; 2012, 38, 1; 67-71
1230-2325
2300-8377
Pojawia się w:
Metallurgy and Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Selection of protective coatings obtained by plasma-spraying method for foundry industry
Dobór powłok ochronnych otrzymanych metodą natrysku plazmowego do zastosowania w przemyśle odlewniczym
Autorzy:
Richert, M.
Nejman, I.
Zawadzka, P.
Kacprzyńska-Gołacka, J.
Powiązania:
https://bibliotekanauki.pl/articles/264269.pdf
Data publikacji:
2017
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
plasma spraying
foundry industry
microstructure
wettability
natrysk plazmowy
przemysł odlewniczy
mikrostruktura
zwilżalność
Opis:
This article presents results from the studies of protective coatings applied to industrial graphite molds used for the casting of non-ferrous metals. The selection of coatings was based on the results of measurements of surface wettability by liquid copper and microstructure examinations. The study involved industrial graphite molds with single-layer protective coatings of Al2O3 + 30%C and ZrO2-Y2O3 + 30%C as well as two-layer protective coatings of Al2O3 + 30%C /glassy carbon and ZrO2-Y2O3 + 30%C /glassy carbon.
W artykule przedstawiono wyniki badań powłok ochronnych przeznaczonych do ochrony grafitowych krystalizatorów stosowanych w przemyśle odlewniczym. Dobór powłok nastąpił na podstawie wyników badań mikrostruktury i pomiarów zwilżalności powierzchni przez ciekłą miedź. Badaniami objęto grafitowe krystalizatory z naniesionymi powłokami ochronnymi: jednowarstwowymi Al2O3 + 30%C i ZrO2-Y2O3 + 30%C oraz dwuwarstwowymi Al2O3 + 30%C /węgiel szklisty i ZrO2-Y2O3 + 30%C /węgiel szklisty.
Źródło:
Metallurgy and Foundry Engineering; 2017, 43, 1; 51-56
1230-2325
2300-8377
Pojawia się w:
Metallurgy and Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Surface Modification on Properties of Stainless Steel Used for Implants
Wpływ modyfikacji powierzchni na właściwości stali nierdzewnej stosowanej na implanty
Autorzy:
Basiaga, M.
Jendruś, R.
Walke, W.
Paszenda, Z.
Kaczmarek, M.
Popczyk, M.
Powiązania:
https://bibliotekanauki.pl/articles/356339.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ALD method
pitting corrosion
scratch test
wettability
AFM
metoda ALD
adhezja warstw
korozja
zwilżalność
Opis:
The aim of the study was assessment of the influence of stainless steel 316 LVM surface modification on its functional properties. The analyzed steel undergone a surface treatment consisting of the following processes: mechanical polishing, chemical passivation and deposition of Al2O3 layers by Atomic Layer Deposition method. The proposed variant of surface treatment will undoubtedly contribute to improving the functional properties of stainless steel intended for implants. In order to assess functional properties of the steel, electrochemical studies, adhesion (scratch test), wetting angle tests and topography of surface (AFM method) were performed. The obtained results of the study showed clearly that the proposed by the authors way of surface treatment including: mechanical polishing, chemical passivation and deposition of Al2O3 layer by means of the ALD method effectively improves the corrosion resistance of stainless steel.
Celem pracy była ocena wpływu modyfikacji powierzchni stali nierdzewnej 316 LVM na jej właściwości funkcjonalne. Obróbka powierzchni składała się z następujących procesów: polerowanie mechaniczne, chemiczna pasywacja i naniesienie warstw Al2O3 metodą ALD (Atomic Layer Deposition). Zaroponowany wariant obróbki powierzchni niewątpliwie przyczyni się do poprawy właściwości funkcjonalnych stali przeznaczonej na implanty. W celu oceny właściwości funkcjonalnych stali przeprowadzono badania elektrochemiczne, badania adhezji warstw (scratch test), oraz badania zwilżalności (kąt zwilżania i badania topografii powierzchni metodą AFM). Uzyskane wyniki badań wykazały wyraźnie, że zaproponowany przez autorów sposób obróbki powierzchni, w tym: polerowanie mechaniczne, pasywacja chemiczna i naniesienie warstw Al2O3 metodą ALD skutecznie poprawia odporność na korozję stali nierdzewnej.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 4; 2965-2970
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Ti and Zr additions on wettability and work of adhesion in Ag/C system
Wpływ Ti i Zr na zwilżalność i pracę adhezji w układzie Ag/C
Autorzy:
Wójcik-Grzybek, D.
Frydman, K.
Sobczak, N.
Nowak, R.
Piątkowska, A.
Pietrzak, K.
Powiązania:
https://bibliotekanauki.pl/articles/192304.pdf
Data publikacji:
2017
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Technologii Materiałów Elektronicznych
Tematy:
wettability
adhesion
contact angle
Ag/C system
zwilżalność
adhezja
kąt zwilżania
układ Ag/C
Opis:
Wettability in the silver/carbon system was examined by the sessile drop method under vacuum at the temperature of 1243 K. Vitreous carbon, diamond and graphite were used as solid substrates. after wettability tests, the solidified Ag/C and Ag-X/C (X - 1 wt.% Ti or Zr) couples were subjected to structural characterization by SEM and EDX analysis. liquid pure silver does not wet these substrates and shows week adhesion, regardless of the type of the carbon material used. the introduction of 1 wt.% carbide forming additions Ti or Zr into silver changes dramatically the interaction in the Ag/C system leading to the formation of continuous reaction product layers (TiCx and ZrCx, respectively) at the drop/substrate interface. these interfacial layers are responsible for good wetting and high work of adhesion between agti1 and AgZr1 alloys and all types of carbon materials examined in this study.
Przedstawiono wyniki badań zwilżalności w układzie srebro/węgiel wykonanych w atmosferze próżni, w temperaturze 1243 K. Pomiary kąta zwilżania wykonano metodą leżącej kropli na podłożach z węgla szklistego, diamentu i grafitu. Po testach zwilżalności wytworzone pary materiałów Ag/C i Ag-X/C (X - 1% wag. Ti lub Zr) poddano analizie strukturalnej metodami SEM i EDX. Ag/C jest układem niereaktywnym, w którym srebro nie zwilża węgla. Prezentowane badania wykazują, że dodatek 1% wag. Ti lub Zr do srebra powoduje obniżenie kątów zwilżania i wzrost wartości pracy adhezji w układzie Ag/C niezależnie od typu materiału węglowego. Jest to związane z powstawaniem na granicy kontaktu kropli z podłożem węglowym warstw przejściowych zawierających węgliki TiCx lub ZrCx.
Źródło:
Materiały Elektroniczne; 2017, T. 45, nr 1, 1; 4-11
0209-0058
Pojawia się w:
Materiały Elektroniczne
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of colloidal silica obtained via the co-precipitation method using octane as an organic phase
Autorzy:
Jesionowski, T.
Tepper, B.
Krysztafkiewicz, A.
Powiązania:
https://bibliotekanauki.pl/articles/778627.pdf
Data publikacji:
2007
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
krzemionka strącana
emulsja
mikroskopia skaningowa
sedymentacja
zwilżalność
precipitated silica
emulsion
PSD
SEM
sedimentation
wettability
Opis:
The studies were conducted on the production of silica from emulsion systems by co-precipitation from solutions of sodium metasilicate and hydrochloric acid and octane were used as an organic medium. The obtained products were subjected to a comprehensive physicochemical analysis in order to define their dispersive and morphological properties. Particle diameters and polydispersity were determined by the NIBS (non-invasive back scattering) method while the shape and morphology of the particles were established using scanning electron microscopy (SEM). In order to determine the adsorptive properties of the obtained monodisperse silicas, isotherms of nitrogen adsorption/desorption on their surfaces were determined. Using the isotherms, also the specific surface area, the diameter and the volume of the pores were established. In order to define the hydrophilic/hydrophobic character of the products, profiles of wettability and of sedimentation in water were examined. The obtained products were well wettable with water and an increase in their weight depended on the amount of the applied surfactants. The particles of the precipitated silicas manifested a defined, spherical shape and showed a relatively low polydispersity.
Źródło:
Polish Journal of Chemical Technology; 2007, 9, 4; 1-4
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Biotribochemistry of the lubrication of natural joints
Biotribochemia smarowania naturalnych stawów
Autorzy:
Pawlak, Z.
Jurvelin, J.
Urbaniak, W.
Powiązania:
https://bibliotekanauki.pl/articles/188874.pdf
Data publikacji:
2010
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
biohydrofobowość
zwilżalność
energia powierzchniowa
współczynnik tarcia i pH
biohydrophobicity
wettability
interfacial energy
friction coefficient and pH
Opis:
In this communication, we attempt to consider changes occurring in the phospholipid biomembrane surface in terms of acid-base equilibria. Specifically, the influence of the pH on surface wettability, interfacial energy, and surface friction is discussed under consideration of a biomembrane as an amphoteric polyelectrolyte. We measured the interfacial energy of phosphatidylserine (PS) using a model of bilayer membrane in aqueous electrolyte over the pH range 2.0-12.0.0. Micro-electrophoresis was used to examine the local acid-base equilibrium of the membrane surface, which can be considered to mimic the interface of natural joints. In our findings, the biohydrophobicity of natural surfaces is greatly reduced in the presence of phospholipids. We were able to demonstrate that the coefficient of friction vs. biohydrophobicity of articular cartilage is interface-controlled by osteoarthritis.
Mechanizm smarowania i tarcia w stawach naturalnych opisany jest w literaturze przez ok. 40 modeli. Znaczny postęp w ostatnich latach zawdzięczamy badaniom eksperymentalnym prowadzonym na poziomie molekularnym. Staw, nazywany biołożyskiem, cechuje ultra-niski współczynnik tarcia rzędu 0,001, często pod obciążeniem do 20 MPa. Maź stawowa (łac. synovia, płyn maziowy) jest środkiem smarującym (pH - 7,4) zawierającym ok. 94% wody, chondrocyty, fosfolipidy o m.cz. 700, biomakrocząsteczki, m.in. lubrycyne, hialuron o m. cz. ok. 200 000. W pracy przedstawiono wpływ pH na hydrofobowość, napięcie powierzchniowe, gęstość ładunku i współczynnik tarcia powierzchni stawu. W naszym micelarno-lamelarnym modelu smarowania dwuwarstwy (membrany) fosfolipidowe (SAL-surface amorphous layer) osadzone są na chrząstce stawowej i z udzialem biomakrocząsteczek zapewniają ultraniskie tarcie. Przy spadku hydrofobowości chrząstki z 105° do ok. 60° i zakłóceniu równowagi kwasowo-zasadowej SAL się nie odtwarzania i tarcie w stawie wzrasta.
Źródło:
Tribologia; 2010, 5; 131-141
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High temperature wettability and reactivity between molten Mg in contact with Ni substrate
Wysokotemperaturowe badania zwilżalności i reaktywności ciekłego Mg w kontakcie z podłożem Ni
Autorzy:
Kudyba, A.
Sobczak, N.
Turalska, P.
Bruzda, G.
Makaya, A.
Pambaguian, L.
Powiązania:
https://bibliotekanauki.pl/articles/391589.pdf
Data publikacji:
2018
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Odlewnictwa
Tematy:
sessile drop
wettability
reactivity
metal matrix composites (MMC)
kropla leżąca
zwilżalność
reaktywność
kompozyty o osnowie metalicznej (MMC)
Opis:
The paper focuses on the experimental investigation of high temperature wetting behaviour of liquid pure Mg during a contact heating on Ni substrate by the sessile drop method. High temperature wettability test was performed by the classical sessile drop method at T = 700°C for t = 300 s, under flowing Ar 99.999% atmosphere, by using the equipment and testing procedures that have been developed by the Foundry Research Institute. In order to suppress effects of heating and cooling histories on wetting and spreading behaviours, Mg/Ni couple was introduced inside a metallic heater already preheated up to the test temperature, while after the wettability test, it was immediately removed to the cold part of the chamber. During the wettability test, images of the couple were recorded by high-resolution high-speed CCD camera. It was observed, that the wetting phenomenon (θ ≤ 90°) takes place immediately after melting of Mg sample. The Mg/Ni system shows a good wetting at T = 700°C after t = 300 s forming the final contact angle of 18°.
Praca prezentuje wyniki badań wysokotemperaturowego oddziaływania ciekłego Mg w kontakcie z podłożem Ni podczas wspólnego nagrzewania badanej pary materiałów. Wysokotemperaturowe badania zwilżalności przeprowadzono klasyczna metodą kropli leżącej w temperaturze T = 700°C i czasie t = 300 s w gazie przepływowym Ar 99,999%. Do badań zastosowano aparaturę i procedury badawcze opracowane w Instytucie Odlewnictwa. W celu eliminacji wpływu historii nagrzewania i chłodzenia na zwilżalność i rozpływność, badany układ Mg/Ni wprowadzono do gorącej części komory badawczej nagrzanej do temperatury badań. Po badaniach zwilżalności badaną parę materiałów natychmiast wprowadzono do zimnej części komory badawczej. Podczas badań zwilżalności stosowano ciągłą rejestrację obrazu badanej pary materiałów za pomocą wysokorozdzielczej kamery cyfrowej CCD. Zaobserwowano, że zjawisko zwilżania (θ ≤ 90°) zachodzi natychmiast po stopieniu próbki czystego Mg. Układ Mg /Ni wykazuje bardzo dobrą zwilżalność w temperaturze T = 700° C po t = 300 s, a końcowa wartość kąta zwilżania wynosi 18°.
Źródło:
Prace Instytutu Odlewnictwa; 2018, 58, 1; 47-53
1899-2439
Pojawia się w:
Prace Instytutu Odlewnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of water glass modification on its viscosity and wettability of quartz grains
Autorzy:
Kmita, A.
Hutera, B.
Powiązania:
https://bibliotekanauki.pl/articles/380220.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
szkło wodne
synteza termiczna
nanocząstka ZnO
lepkość
zwilżalność
water glass
modification
thermal synthesis
ZnO nanoparticles
viscosity
wettability
Opis:
The aim of the present study was to develop a modifier for water glass. The method of thermal generation of metal oxide nanoparticles was adapted and used in the research. Nanoparticles of ZnO from the thermal decomposition of basic zinc carbonate were used. A method for the modifier introduction was developed, and the effect of modifier content and organic solvent type on the physico-chemical properties of binder (viscosity) and quartz wettability was determined. Binder viscosity was examined from the flow curves plotted with the help of a RHEOTEST 2 rotational rheometer equipped with proper software. Quartz wettability was determined examining time-related changes in the value of the contact angle in a quartz-binder system, until full stabilisation of the angle value has been achieved. Binder modification was carried out on sodium water glass designated as R"145". The water glass modifiers were suspensions of ZnO nanoparticles in propanol and methanol at a fixed concentration of c = 0.3 M and with the size of nanoparticles comprised in a range of <61 - 981 nm>. Water glass modification with the suspensions of ZnO nanoparticles in methanol and propanol showed the effect of modifier on the water glass viscosity and quartz wettability. This effect depends on the type of alcohol used. The ZnO suspension in propanol (alcohol with a longer hydrocarbon chain) affects more strongly the viscosity of binder and quartz wettability than the methanol suspension.
Źródło:
Archives of Foundry Engineering; 2012, 12, 3; 59-62
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Relative wettability measurement of porous diffuser and its impact on the generated bubble size
Autorzy:
Al-Yaqoobi, Atheer M.G.
Zimmerman, William B.
Powiązania:
https://bibliotekanauki.pl/articles/2173415.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
kąt kontaktu
dyfuzor porowaty
metoda Washburn
zwilżalność
bubble size
contact angle
porous diffuser
Washburn method
wettability
Opis:
Controlling the bubble size is a major concern in enhancing transport performance in gas-liquid systems. The role of wettability of diffuser surface on bubble size is the subject of the current work. The study inspects the contact angle of a set of liquids on HP ceramic diffusers using the Washburn method. The results demonstrate that organic liquids like toluene, methanol–water (1:1 v/v), ethanol– water (1:1 v/v) and decane have small contact angles of 12.9, 37.5, 24.4 and 22.5 respectively. Water has a lower wettability than the organic compounds where the contact angle was about 67.4. The effect of wettability of the bubble size is investigated by measuring the size of air bubble produced using the same diffuser material. The results of bubble size measurement demonstrates that with liquids of small contact angle, i.e. good wetting properties, small bubble sizes are produced in comparison with liquids with a higher contact angle. The study demonstrates the viability of Washburn method in characterization of wettability of porous diffuser, which was verified by measuring the bubble size produced. A high reduction in bubble size can be obtained by a carefully chosen diffuser material that provides better wettability.
Źródło:
Chemical and Process Engineering; 2022, 43, 1; 45--55
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Static and Dynamic Mechanical Properties of Cotton/Epoxy Green Composites
Statyczne i dynamiczne mechaniczne właściwości bawełniano-epoksydowych “zielonych” kompozytów
Autorzy:
Koyuncu, M.
Karahan, M.
Karahan, N.
Shaker, K.
Nawab, Y.
Powiązania:
https://bibliotekanauki.pl/articles/234431.pdf
Data publikacji:
2016
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
natural fibres
adhesion
alkaline
composites
wettability
glass transition temperature
włókna naturalne
obróbka alkaliczna
kompozyty epoksydowe
zwilżalność
temperatura zeszklenia
Opis:
A study on the effect of alkaline treatment on the mechanical properties of cotton fabric reinforced epoxy composites is presented in this paper. One hour treatment of cotton fabric was performed using three different concentrations of sodium hydroxide (NaOH) solution. 1% NaOH treated fabric reinforced composites exhibited maximum improvement in tensile strength. It was concluded that the said NaOH concentration improves interfacial adhesion between the cotton fabric and epoxy resin. Moreover the morphology of the fracture surface, evaluated by scanning electron microscopy (SEM), indicated that surface treatment can yield better adhesion between the fabric and matrix, demonstrating the effectiveness of the treatment. The dynamic mechanical analysis (DMA) results revealed that alkali treated (1% and 3% NaOH) fabric composites exhibit higher storage moduli and glass transition temperature (Tg) values as compared to the untreated fabric composites. However, for all the composite specimens, the storage modulus decreased with increasing temperature (25 - 100 °C). Tg values of 50.9, 56.7, 52.8 and 37.7 °C were recorded for the untreated and (1%, 3% and 5%) treated composites, respectively. The tan δ values decreased for all the composites with increasing temperature, indicating enhanced interactions between the polymer matrix and fabric reinforcement.
Badano wpływ obróbki alkalicznej na mechaniczne właściwości tkanin bawełnianych wzmacniających kompozyty epoksydowe. Stosowano jednogodzinną obróbkę tkanin bawełnianych przy stosowaniu trzech różnych stężeń NaOH. Stwierdzono, że tkaniny poddane działaniu 1% NaOH wykazują najlepsze właściwości biorąc pod uwagę wytrzymałość na rozciąganie. Stwierdzono, że obróbka alkaliczna polepsza międzyfazową adhezję pomiędzy bawełnianą tkaniną i żywicą epoksydową. Oprócz tego stwierdzono, badając morfologię przełomów za pomocą SEM, że obróbka powierzchniowa pozwala na uzyskanie lepszej adhezji pomiędzy tkaniną a matrycą epoksydową. Stwierdzono również zmiany składowej rzeczywistej modułu zespolonego oraz wartości temperatury i przemiany szklistej. Ze wzrostem temperatury zmienia się również tan δ dla wszystkich kompozytów potwierdzając polepszającą się interakcję pomiędzy matrycą polimerową i włóknistym wzmocnieniem.
Źródło:
Fibres & Textiles in Eastern Europe; 2016, 4 (118); 105-111
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wettability of the System of Cast Iron and Magnesia Ceramics with Graphite
Autorzy:
Hosadyna-Kondracka, Małgorzata
Nowak, Rafał
Turalska, Patrycja
Bruzda, Grzegorz
Boroń, Łukasz
Wawrylak, Marek
Powiązania:
https://bibliotekanauki.pl/articles/2174618.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
composites
metal-ceramic bonding
wettability
sessile drop method
cast iron
kompozyty
wiązanie metal-ceramika
zwilżalność
metoda osiadłej kropli
żeliwo
Opis:
In this paper examinations of high-temperature wetting tests of 3 systems of liquid alloy – cast iron in contact with ceramic materials: magnesia ceramics in combination with natural graphite were presented. After wettability testing, the microscopic observations of the morphology of the sample surface and the cross-section microstructure with the chemical composition in micro-areas were examined. One of the objective of this work was also to verify whether the graphite content would affect the wettability of the magnesia ceramics. The study of high-temperature wetting kinetics of the liquid alloy in contact with the ceramic material, by the "sessile drop" method with capillary purification (CP) procedure was conducted. Under the test conditions, at a temperature of 1450°C and time 15 minutes, all 3 experimental systems showed a non-wetting behaviour. The average contact angle for the system with cast iron drop on magnesia ceramics was 140°, on magnesia ceramics with 10 parts per weight of graphite was 137° and on magnesia ceramics with 30 parts per weight of graphite - 139°. Microscopic observations revealed that in the case of the sample consisting of the cast iron drop on the substrate with magnesia ceramics, the formation of fine separations was not observed, unlike the systems with the substrate with magnesia ceramics and the addition of natural graphite. Numerous, fine droplets accumulate on the graphite flakes and consist mainly of Si as well as Fe and O. On the other hand, the rough MgO grains have a gray, matt surface, without fine separations. The conducted observations indicate the mechanical nature of the bonding - liquid metal penetrates into the pores of the rough ceramics of the substrate. However, in the case of systems of cast iron drop with magnesia ceramics and addition of graphite, probably the adhesive connection and the physical attraction of elements derived from cast iron drop with the flake graphite appeared as well.
Źródło:
Archives of Foundry Engineering; 2022, 22, 3; 25--33
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wettability and Surface Free Energy of Ti(C,N) Coatings on Nickel-based Casting Prosthetic Alloys
Autorzy:
Banaszek, K.
Klimek, L.
Powiązania:
https://bibliotekanauki.pl/articles/381148.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
dental alloy
wettability
contact angle
surface tension
surface free energy
stop dentystyczny
zwilżalność
kąt zwilżania
napięcie powierzchniowe
energia powierzchniowa swobodna
Opis:
The production process of prosthetic restorations runs in two stages. In the first stage, the prosthetic foundation is produced of metal alloys. In the second stage, a facing material is applied on the produced element. In both stages, the wettability is significantly important, as well as the free surface energy relating to it. The quality of the obtained cast depends on the surface phenomena occurring between the metal alloy and the material of which the casting mould is made. The performed examinations also point to a relation between the ceramics joint and the base, depending on the wetting angle. The aim of the presented paper was to examine influence of the composition of a Ti(C,N)-type coating on bases made of the Ni-Cr prosthetic alloy on the wettability and the surface free energy. The test material were disks made of the Ni-Cr alloy with the diameter of 8 mm. The disks were divided into five groups, which were covered with Ti(C,N) coatings, with different amounts of C and N in the layer. In order to determine the surface free energy (γs), the wetting angle was measured. Two measure liquids were applied: distilled water and diiodomethane. The obtained results of the measurements of the water-wetting angles suggest that together with the increase of the ratio of nitrogen to carbon in the Ti(C,N) coating, the surface hydrophobicity increases as well. In all the samples, one can see a large difference between the energy values of the polar and the apolar components. The high values of the polar components and the low values of the apolar ones make it possible to conclude that these surfaces exhibit a greater affinity to the polar groups than to the apolar ones. On the basis of the analysis of the surface free energy, one can state that covering the alloy with Ti(C,N)-type coatings should not decrease the adhesion of the ceramics to the alloy, whereas TiC coatings should lead to the latter’s improvement. Due to their hydrophilicity, TiC coatings should decrease the adhesion of bacteria to the surface and hinder the formation of a bacterial biofilm.
Źródło:
Archives of Foundry Engineering; 2015, 15, 3; 11-16
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation of the Wicking and Drying Behaviour of Polyester Woven Fabrics
Badanie zwilżalności (efektu kapilarnego) i suszenia tkanin poliestrowych
Autorzy:
Saricam, C.
Kalaoğlu, F.
Powiązania:
https://bibliotekanauki.pl/articles/232031.pdf
Data publikacji:
2014
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
wicking
drying
woven fabrics
weave type
weft density
yarn type
zwilżalność
suszenie tkanin
tkaniny poliestrowe
rodzaj przędzy
przepuszczalność tkanin
Opis:
This paper investigated the wicking and drying behaviour of polyester woven fabrics. The effects of yarn type, weft density, weave structure, thickness and air permeability were evaluated by the application of vertical wicking, transfer wicking and drying tests. Correlation analysis and two sided independent t-tests of the data obtained from experiments and the evaluations reveal that the texturizing process - the alteration of the arrangement and packing of yarns by changing the weft density and weave type, are influential with respect to the wicking performance. Moreover the drying behaviour is influenced by the thickness of the fabric, air permeability and yarn type used in the fabric.
W pracy badano zwilżanie (efekt kapilarny) i suszenie tkanin poliestrowych. Badano wpływ typu włókna, gęstość wątku, rodzaj splotu, grubość i przepuszczalność powietrza. Wykonano analizę korelacji i dwustronny t-test. Wyniki wykazały wpływ konfiguracji i upakowania przędz na zwilżanie uwidaczniające się przy zmianie gęstości wątku oraz typu splotu. Ponadto stwierdzono, że zachowanie się tkanin przy suszeniu zależy od ich grubości, przepuszczalności powietrza oraz typu zastosowanych przędz dla otrzymania danej tkaniny.
Źródło:
Fibres & Textiles in Eastern Europe; 2014, 3 (105); 73-78
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Substantiation of fluid saturation of reservoir-rocks on the basis of petrophysical studies
Badanie nasycenia płynami skalnych warstw złożowych na podstawie badań petrofizycznych
Autorzy:
Fedyshyn, V.
Nesterenko, M.
Powiązania:
https://bibliotekanauki.pl/articles/300325.pdf
Data publikacji:
2008
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
skała zbiornikowa
porowatość
nasycenie wodą resztkową
zwilżalność
struktura nasycenia ropą
reservoir rocks
porosity
residual water saturation
wettability
oil saturation structure
Opis:
The method of quantitative estimation of porous medium structural parameters by distinctive areas of capillary pressure curves is proposed, according to which the part of hypercapillary, capillary and subcapillary pores is being determined. Their relations stipulate to a great extent the character of reservoir rocks saturation with residual water and hydrocarbon fluids. Differentiation of oil is carried out in reservoir rocks (Horizon V-22 of Buhru-vate and horizons V-20-21, V-25-26 of Yuliyivs'k fields of Dniepro-Donets depression), in Lower Cretaceous terrigenous and Upper Jurassic carbonate reservoirs of Lopushnia field (Precarpathian oil and gas bearing region) and in reservoir rocks of Middle Cambrian Age of Girkaliai field (Baltic oil bearing region) by parameters of its displacement taking into account hydrodynamic and capillary forces. That permitted to advance arguments for total and recoverable oil reserves of the above-mentioned fields.
W pracy przedstawiono metodę ilościowego szacowania parametrów strukturalnych ośrodka porowego na podstawie wykresów ciśnienia kapilarnego, zgodnie z którymi określono obszary występowania porów z ciśnieniem hiperkapilarnym, kapilarnym i podkapilarnym. Ich wzajemne relacje w dużym stopniu determinują charakter skał zbiornikowych w resztkową wodą i płynnymi węglowodorami. Stwierdzono obecność ropy naftowej w następujących warstwach piętrach (horyzont V-22 w złożu Buhruvate oraz horyzonty V-20-21 i V-25-26 w złożu Yuliyivs'k w Zagłębiu Dnieprowsko-Donieckim), w dolnokredowych utworach terrygenicznych oraz górnokarbońskich warstwach węglanowych złoża Łopuszna (przedkarpacki obszar ropo- i gazonośny) oraz w środkowokambryjskich skałach zbiornikowych złoża Girkaliai (bałtycki obszar roponośny) na podstawie parametrów przemieszczeń, z uwzględnieniem sił kapilarnych oraz hydrodynamicznych. Umożliwiło to oszacowanie wszystkich i produkcyjnych zasobów ropy naftowej na wymienionych złożach.
Źródło:
Wiertnictwo, Nafta, Gaz; 2008, 25, 2; 265-269
1507-0042
Pojawia się w:
Wiertnictwo, Nafta, Gaz
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies