Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "thermal field" wg kryterium: Temat


Tytuł:
Measuring temperature distribution on the surface of flying missiles
Autorzy:
Szklarski, A.
Świderski, W.
Machowski, B.
Powiązania:
https://bibliotekanauki.pl/articles/245906.pdf
Data publikacji:
2015
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
missiles
wind tunnel
thermal field
boundary layer
Opis:
There are problems associated with flight of objects such as rockets after exceeding sound barrier. One of them is heating up their body during the flight, especially at low altitudes. Overheated surface of rocket leads to serious consequences, such as rapid destruction of material components of missile. It could cause an interference with target tracking signal if it is on the spectral range of missile optoelectronic detecting head. It can cause destruction of flying missile in extreme cases. In addition, temperature increase causes an increase of drag force of object what directly influences its ballistic parameters. The subject of the paper is to present a concept of experimental set-up to test the heating of missile body at flight. The set-up is based on a wind tunnel. Four missiles were selected for initial analysis in order to test some typical designs for significantly different flight velocities and aerodynamics. Boundary layer at flow around the surface, determining temperature field of missile, the local distribution of heat transfer coefficients on the sphere and exemplary distribution of temperature and pressure on the sphere during flow around, distribution of Nusselt numbers for different velocities of flow around roll, numerical model of rockets, distribution of Mach number, temperature field and velocity vectors are presented.
Źródło:
Journal of KONES; 2015, 22, 2; 233-239
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermal fields calculation of cylindrical inductor loaded by a bundle of ferromagnetic rods
Obliczanie pola temperatur cewki indukcyjnej obciążonej wiązką prętów ferromagnetycznych
Autorzy:
Berezyuk, A.O.
Kondratenko, I.P.
Rashhepkin, A.P.
Powiązania:
https://bibliotekanauki.pl/articles/56192.pdf
Data publikacji:
2013
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
thermal field
calculation
cylindrical inductor
finite element method
ferromagnetic field
Opis:
In this paper the combined method of calculating thermal and electromagnetic fields of a cylindrical inductor, which is loaded by a bundle of ferromagnetic rods, has been developed. The method is based on the analytical solution of the electromagnetic characteristics and 2-D (FEM) simulation of the allocation of temperature fields by finite element method. It was found that the steady state of the inductor, which has the installed capacity of 4.5 kW, comes in 350—100 s. after heating, the maximum temperature of the rods in the central zone is 68°C, the temperature of the heated material - 48°C, which satisfies the technological process of heating the seeds before removing oil.
Obliczanie pola temperatur cewki indukcyjnej obciążonej wiązką prętów ferromagnetycznych. Opracowano metodę obliczeń pola temperatur i charakterystyki elektromagnetycznej wymiennika ciepła w postaci cylindrycznej cewki indukcyjnej obciążonej wiązką prętów ferromagnetycznych. Opracowana metoda jest oparta na obliczeniach gęstości wytwarzania ciepła i aproksymacji wyników przy użyciu wielomianów opisujących alokację gęstości temperatur. Przedstawiono numeryczne rozwiązania problemów termicznych przy wykorzystaniu metody elementów skończonych. Stwierdzono, że stan ustalony cewki o zainstalowanej mocy 4,5 kW występował po czasie 35CM00 s po ogrzaniu, maksymalna temperatura prętów w strefie środkowej wynosiła 68°C, a temperatura ogrzewanego materiału 48°C; spełnia to wymagania procesu technologicznego ogrzewania nasion przed ekstrakcją oleju.
Źródło:
Annals of Warsaw University of Life Sciences - SGGW. Agriculture; 2013, 62 Agric.Forest Eng.
0208-5712
Pojawia się w:
Annals of Warsaw University of Life Sciences - SGGW. Agriculture
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Geophysical cartography in Poland : an overview
Autorzy:
Krzywiec, P.
Nawrocki, J.
Polechońska, O.
Wróblewska, M.
Powiązania:
https://bibliotekanauki.pl/articles/2065895.pdf
Data publikacji:
2005
Wydawca:
Państwowy Instytut Geologiczny – Państwowy Instytut Badawczy
Tematy:
geophysical cartography
seismic data
magnetic field
gravity field
thermal field
petrophysical parameters
Opis:
Regional analysis and mapping of various geophysical data has been recognized as an important — even crucial — element of geological studies for many years. Due to rapid development of advanced numerical tools it is presently possible to construct, maintain and comprehensively analyse even very large geo-databases, including seismic, gravity, magnetic, geothermal and other geophysical data. In many countries, national geological surveys, commercial companies and research institutions are involved in mapping projects focused on spatial representation of geophysical data that could later be used for various studies. Recently, new policy of the Polish Ministry of Environment regarding geological cartography in years 2005–2020 has been declared (cf. Ber & Jezierski, 2004). In this document, geological cartography is used as a rather wide term that includes also other geo-disciplines like geoenvironmental studies or surface geochemistry. Among them, mapping of geophysical data is also mentioned. In this paper, short overview of the current state-of-the-art of selected aspects of regional geophysical mapping in Poland is given, with some remarks regarding potential directions of future work.
Źródło:
Przegląd Geologiczny; 2005, 53, 10/2; 967-972
0033-2151
Pojawia się w:
Przegląd Geologiczny
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of permanent magnet linear motor parameters taking its heating into account
Autorzy:
Waindok, A.
Powiązania:
https://bibliotekanauki.pl/articles/140827.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
linear synchronous motors
thermal field calculation
permanent magnets parameters
Opis:
The calculation results of the static field parameters for permanent magnet linear synchronous motor have been presented in this work. The influence of the construction temperature on the parameters has been analyzed mathematically. Models for magnetic and temperature fields determination have been formulated. Two kinds of permanent magnets (NdFeB and SmCo) have been considered. The distribution of the thermal field has been obtained using the finite element method (FEM).
Źródło:
Archives of Electrical Engineering; 2012, 61, 4; 471-482
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The impact of speed as well as selected parameters of slot insulation on the distribution of temperature in linear motion converters
Autorzy:
Mikołajewicz, J.
Powiązania:
https://bibliotekanauki.pl/articles/141198.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
thermal field
finite element method
linear motors
numerical analysis
Opis:
This paper presents and discusses the mathematical model of thermal phenomena occurring in axis-symmetric electromechanical linear motion converters. On the basis of the developed model, software to analyze the process of the heating up of this type of converters, was created. The effect of the thickness and type of material of the slot insulation, as well as the speed of the runner on the temperature distribution in the analyzed object was examined in-depth. Selected results of simulated calculations have been presented.
Źródło:
Archives of Electrical Engineering; 2016, 65, 4; 855-864
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Induction heater in the electric pasteuriser
Autorzy:
Bodziak, K.
Goleman, R.
Nalewaj, K.
Powiązania:
https://bibliotekanauki.pl/articles/25826.pdf
Data publikacji:
1999
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
thermal field
heat exchange
heating system
electromagnetic field
induction heater
electrical pasteuriser
Źródło:
International Agrophysics; 1999, 13, 3
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Thermal fields in grain during storage - their sources and effects on silo structure reliability
Autorzy:
Lapko, A.
Powiązania:
https://bibliotekanauki.pl/articles/25507.pdf
Data publikacji:
2005
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
moisture
thermal field
silo
temperature
structure
grain
numerical analysis
storage
Źródło:
International Agrophysics; 2005, 19, 2
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Temperature distribution in multi domain construction of the permanent magnet linear actuator
Autorzy:
Tomczuk, B.
Waindok, A.
Powiązania:
https://bibliotekanauki.pl/articles/140715.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
linear actuators
thermal field models
heating curves calculation
finite element model
Opis:
The transient thermal model of the permanent magnet linear actuator (PMLA) has been considered. The characteristics of heating have been calculated including the main subdomains of the actuator. The carcasses from various materials have also been considered. The calculations have been verified experimentally and a good conformity was obtained.
Źródło:
Archives of Electrical Engineering; 2013, 62, 3; 417-424
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design and analysis of the ferrite air-gapped cores for a resonant inductor
Autorzy:
Zheng, J.
Wang, Ch.
Xia, D.
Powiązania:
https://bibliotekanauki.pl/articles/949922.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
three-air-gapped
electromagnetic and thermal field
finite element method
resonant inductor
Opis:
In this paper, a three-air-gapped structure of a ferrite core for a resonant inductor is proposed. The electromagnetic and thermal field models are built using a 3D finite element method. Compared with the conventional signal-air-gapped structure of a ferrite core, the simulation and analysis results show that the proposed three-air-gapped ferrite core resonant inductor can reduce eddy-current loss and decrease temperature rise. In addition, the optimal position of air-gapped is presented.
Źródło:
Archives of Electrical Engineering; 2018, 67, 3; 579--589
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Energy efficiency analysis of railway turnout heating system with a melting snow model heated by classic and contactless heating method
Autorzy:
Flis, Mateusz
Powiązania:
https://bibliotekanauki.pl/articles/140565.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
electrical heating
enthalpy method
experimental research
melting process
railway turnouts
thermal field
heat distribution
Opis:
Maintaining railway turnout operability is crucial for ensuring railway transport safety. Electric heating of railway turnouts is a significant technical and economic issue. The classical heating is characterised by high power consumption. For this reason, research is needed to optimise the current system. This paper presents results of a numerical analysis and of experimental researches. The numerical analysis was carried out using the ANSYS software. There was conducted a numerical comparative analysis of energy loss during heating performed using two different heaters. Including the classical method and a heater thermally insulated from a rail. In the first step, heating of a working space filled with a substitute snow model was considered. The snow-covered surface area was held within the working space of the turnout. It was assumed that the snow substitute material had thermal properties approximately the same as real light snow. It was also assumed that the material is in the solid state which would not undergo a phase change. In the next step, a real snow model that included the phase change process was taken into account. The energy efficiency and heat distribution in the turnout have been analysed and compared. The experimental researches were carried out in a physical model. The results showed that the use of a contactless heater results in creating a larger area over which emitted heat affected snow in the working space. Consequently, more snow was melted around the contactless heater than the classic one. This experimental observation supported the results of the numerical analyses presented previously.
Źródło:
Archives of Electrical Engineering; 2019, 68, 3; 511-520
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Simulation of thermal field in soil
Symulacja pola rozkładu temperatury w glebie
Autorzy:
Shevchenko, I.
Kovyazin, A.
Kamiński, J. R.
Szeptycki, A.
Powiązania:
https://bibliotekanauki.pl/articles/238989.pdf
Data publikacji:
2017
Wydawca:
Instytut Technologiczno-Przyrodniczy
Tematy:
soil
thermal field
soil thermal conductivity
soil thermal resources
depth
gleba
pole rozkładu temperatury
przewodność cieplna
zasobność cieplna
głębokość
Opis:
Heat energy resources from the ground may be rationally used to maintain optimal microclimate conditions inside livestock buildings. Simulation of heat and mass exchange, as factors influencing the thermal field in the ground, is extremely complicated because of the necessity of taking into consideration many different mechanisms that govern the happening phenomenae and also chemical and mineralogical properties of the very complicated, multicomponent medium of soil. The parabolic, partial differential equation was proposed as one which describes accurately enough the simulated problem. In this case soil was considered as a quasi-homogenic body for which a normal equation for heat conduction may be applied, interrelating the temperature T, time t and depth z. The simulation for climatic conditions at Zaporozhye region (Ukraine) demonstrated that the annual temperature oscillation in soils reaches 9-17 m in depth, depending of the soil type and its heat conductivity. The results of simulation may be used in technical solutions to harness the geothermal sources of heat.
Zasoby energii cieplnej gruntu mogą być wykorzystane w celu zapewnienia należytego mikroklimatu w budynkach inwentarskich. Symulowanie wymiany ciepła i masy jako czynników pola rozkładu temperatury w gruncie jest wysoce skomplikowane ze względu na konieczność uwzględnienia znacznej liczby mechanizmów rządzących zachodzącymi zjawiskami, a także chemicznych i mineralogicznych własności bardzo złożonego środowiska glebowego. Zaproponowano wykorzystanie parabolicznego, cząstkowego równania różniczkowego, dostatecznie dokładnie opisującego ekwiwalentną przewodność cieplną gleby. Założono przy tym, że gleba jest quasi-homogenicznym ośrodkiem, w odniesieniu do którego może być zastosowane zwykłe równanie przewodzenia ciepła uzależniające wzajemnie temperaturę T, czas t i głębokość z. Wyniki symulacji dla warunków klimatycznych regionu Zaporoża (Ukraina) świadczą, że wahania temperatury w ciągu roku sięgają, zależnie od rodzaju gleby i jej przewodności cieplnej, do głębokości 9-17 m. Wyniki symulacji mogą być zastosowane w rozwiązaniach technologicznych służących do wykorzystania ciepła z gruntu.
Źródło:
Problemy Inżynierii Rolniczej; 2017, R. 25, nr 1, 1; 57-65
1231-0093
Pojawia się w:
Problemy Inżynierii Rolniczej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation of the skull melting method for the generation of particulate material of inorganic compounds
Autorzy:
Riemer, B.
Lange, E.
Hameyer, K.
Powiązania:
https://bibliotekanauki.pl/articles/140920.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
tygiel
topienie
pole elektromagnetyczne
pole termiczne
sprzężenie
skull melting
cold crucible
electromagnetic thermal field coupling
Opis:
This paper describes the application of the skull melting method for an artificial generation of particulate material of inorganic compounds like CsOH, NaOH, SnO2 and UO2. The skull melting process is analyzed analytically. Thereby the electromagnetic field is calculated by a one dimensional time harmonic model. Thermal losses are estimated by simple analytical formulas. Finally an electromagnetic thermal field coupling is performed to calculate the temperature distribution inside the crucible, considering transient thermal effects. The skull melting process is simulated for the example of UO2. Under consideration of the given material properties it is shown that the skull melting method can be applied to fuse UO2.
Źródło:
Archives of Electrical Engineering; 2011, 60, 2; 197-209
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Information energy diagrams of thermodynamic interaction at drying of printed products
Informacyjno-energetyczne wykresy termodynamicznego współdziałania przy suszeniu produkcji poligraficznej
Autorzy:
Durnyak, B.
Strepko, I.
Fedyna, B.
Powiązania:
https://bibliotekanauki.pl/articles/128511.pdf
Data publikacji:
2015
Wydawca:
Centralny Ośrodek Badawczo-Rozwojowy Przemysłu Poligraficznego
Tematy:
drying
energy flow
mathematic model
thermal field
optimal control
energy diagram
suszenie
przepływ energii
model matematyczny
pole termiczne
kontrola optymalna
diagram energetyczny
Opis:
The article analyses information energy diagrams of thermodynamic interaction at drying of printing products. It shows the models of thermodynamic interaction of thermal energy with drying objects. We have built the structure of the integrated system of thermal process control at drying of printing products. We have formulated the tasks of optimization of drying technological process.
Podjęto problem zapewnienia prawidłowości technologicznego procesu suszenia produkcji poligraficznej, który dotychczas nie był w pełni rozwiązany, m.in. z powodu rozmaitości obiektów o różnej postaci fizycznej, chemicznej, strukturalnej oraz wielorakich właściwościach. Także w źródłach energii cieplnej stosowane są różne rozwiązania systemu działania. Autorzy proponują optymalizować proces technologiczny przez zbudowanie strukturalnego schematu obiektu suszenia oraz identyfikację parametrów na podstawie równania termodynamiki procesu wymiany dla źródeł danego typu i samej suszarki. Graniczne wymagania procesu suszenia oparto na kompleksowych badaniach eksperymentalnych i teoretycznych. W efekcie uzyskano bezawaryjność procesu oraz jego efektywność.
Źródło:
Acta Poligraphica; 2015, 5; 9-13
2299-9981
Pojawia się w:
Acta Poligraphica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of road excitation on thermal field characteristics of the water-cooled IWM
Autorzy:
Feng, Jie
Tan, Di
Yuan, Meng
Powiązania:
https://bibliotekanauki.pl/articles/1841132.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
road excitation
in-wheel motor drive system
thermal field characteristics
water-cooled in-wheel motor
ekscytacja drogowa
napęd silnikowy
charakterystyka pola cieplnego
silnik chłodzony wodą
Opis:
The in-wheel motor is installed in wheels, and road excitation acts on the in-wheel motor directly through a wheel, which affects the flow field characteristics of the motor’s liquid cooling system, and affects the thermal field characteristics of the in-wheel motor. Aiming at this problem, the in-wheel motor drive system is taken as the research object in this paper. Firstly, the heat flow coupling analysis model of the in-wheel motor drive system is established by using the heat flow coupling theory. Then the vibration response of in-wheel motor stator and shell under different road excitation obtained from the previous study is taken as the load. Finally, thermal field characteristics of the water-cooled the in-wheel motor under different working conditions are studied, and the influence law of different speed and road grades on the thermal field characteristics is obtained. The results show that under the road excitation, the maximum temperature of each component of the in-wheel motor decreases due to the vibration effect of road excitation on the flow field of the cooling system, and the decrease of the stator and winding is the most obvious. Additionally, the higher the speed, the greater the road roughness coefficient, the greater the temperature drop of each component of the in-wheel motor. However, the thermal field distribution of local parts of the motor is relatively uneven under road excitation, which leads to greater thermal stress of the local parts and increases the risk of motor damage.
Źródło:
Archives of Electrical Engineering; 2021, 70, 3; 689-704
1427-4221
2300-2506
Pojawia się w:
Archives of Electrical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical Model for Solidification Zones Selection in the Large Ingots
Autorzy:
Wołczyński, W.
Kwapisiński, P.
Kania, B.
Wajda, W.
Skuza, W.
Bydałek, A. W.
Powiązania:
https://bibliotekanauki.pl/articles/379882.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
theory of crystallization
thermal gradient field
constrained solidification
unconstrained solidification
teoria krystalizacji
gradientowe pole temperatury
krzepnięcie ograniczone
Opis:
A vertical cut at the mid-depth of the 15-ton forging steel ingot has been performed by curtesy of the CELSA – Huta Ostrowiec plant. Some metallographic studies were able to reveal not only the chilled undersized grains under the ingot surface but columnar grains and large equiaxed grains as well. Additionally, the structural zone within which the competition between columnar and equiaxed structure formation was confirmed by metallography study, was also revealed. Therefore, it seemed justified to reproduce some of the observed structural zones by means of numerical calculation of the temperature field. The formation of the chilled grains zone is the result of unconstrained rapid solidification and was not subject of simulation. Contrary to the equiaxed structure formation, the columnar structure or columnar branched structure formation occurs under steep thermal gradient. Thus, the performed simulation is able to separate both discussed structural zones and indicate their localization along the ingot radius as well as their appearance in term of solidification time.
Źródło:
Archives of Foundry Engineering; 2015, 15, 4; 87-90
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies