Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "stal manganowa" wg kryterium: Temat


Wyświetlanie 1-2 z 2
Tytuł:
Comparison of Austempered Ductile Iron and Manganese Steel Wearability
Autorzy:
Kochański, A.
Krzyńska, A.
Chmielewski, T.
Stoliński, A.
Powiązania:
https://bibliotekanauki.pl/articles/382897.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
austempered ductile iron
manganese steel
wear resistance
hardness
żeliwo sferoidalne
stal manganowa
odporność na ścieranie
twardość
Opis:
The results of comparison of the wear resistance of manganese steel X120Mn12, S235IR steel and austempered ductile iron ADI are presented. The aim of this study is to determine the possibility of replacing an item made of X120Mn12 steel with another material. For this purpose, all of the samples were measured for Brinell hardness. The samples were then tested for wear resistance in a specially designed test stand. The test resided in shot penning the surface of the test samples within the shot stream with the defined parameters. The test stand used in the test ensured the shot penning parameter stability. The test samples underwent multiple tests in which shot penning occurred in reccurrent cycles. Three test limits were established for the present study: 60, 120 and 180 cycles. The wear resistance measure in this study was the decrease in the tested sample’s weight expressed in grams and calculated for a unit of the shot-penned surface. The obtained results confirmed the possibility of using ADI as a possible replacement of manganese steels in specific cases. Of the eight types of the samples tested, the two ADI samples exhibited abrasion resistance which was comparable to that of the reference sample, while one exhibited better resistance. What constitutes the optimal chemical composition and the corresponding optimal heat treatment for particular cases remains an issue for further research.
Źródło:
Archives of Foundry Engineering; 2015, 15, 1 spec.; 51-54
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Microstructure and mechanical properties of Cr-Mn structural PM steels
Mikrostruktura i własności mechaniczne spiekanych, konstrukcyjnych stali chromowo-manganowych
Autorzy:
Sułowski, M.
Ciaś, A.
Powiązania:
https://bibliotekanauki.pl/articles/351061.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stal chromowo-manganowa
spiekanie
szybkość chłodzenia
własności mechaniczne
PM Cr-Mn steels
mechanical properties
sintering atmosphere
cooling rate
sinter-hardening
Opis:
The effects of chemical composition, sintering atmosphere and cooling rate on density, microstructure and mechanical properties of Fe-3%Mn-(Cr)-(Mo)-0.3%C PM steels are described. Pre-alloyed Astaloy CrM and Astaloy CrL, ferromanganese and graphite powders were used as the starting materials. After pressing in rigid dies the compacts were sintered at 1120 and 1250°C for 60 minutes atmospheres with different H2/N2 ratios and cooled either at 1.4°Cmin-1 (with the furnace) or 65°Cmin-1 (convective cooling). The convective cooled specimens were subsequently tempered at 200°C for 60 and 240 minutes. All specimens were tested for tensile strength (UTS), elongation (A), offset yield strength (R0.2), TRS, impact toughness and apparent surface hardness (HV 30). After mechanical tests the microstructure of the Fe-Mn-Cr-Mo-C PM steels was studied by optical microscopy. It has been found that by sintering in inexpensive and safe nitrogen-rich atmospheres it is possible to achieve properties similar to those shown by specimens sintered in a hydrogen-rich atmosphere.
W pracy przedstawiono wpływ składu chemicznego mieszanki proszków, a także rodzaju atmosfery oraz szybkości chłodzenia na gęstość, mikrostrukturę oraz własności mechaniczne spiekanych stali konstrukcyjnych Fe-3%Mn-(Cr)-(Mo)-0.3%C. Do badań wykorzystane zostały wstępnie stopowane, komercyjne proszki żelaza Astaloy CrL i Astaloy CrM, produkcji szwedzkiej firmy Höganäs oraz niskowęglowy proszek żelazomanganu i proszek grafitu. Prasowanie mieszanek proszków o żądanym składzie chemicznym realizowano w stalowych matrycach, wykonując wypraski prostopadłościenne o wymiarach 5×10×55 mm oraz wytrzymałościowe (zgodne z PN-EN ISO 2740). Spiekanie kształtek odbywało się w temperaturze 1120 i 1250°C w czasie 60 minut, w atmosferze o różnej zawartości wodoru i azotu. Chłodzenie spieków prowadzono z szybkością 1,4°C/min (z piecem) lub 65°C/min (konwekcyjnie w chłodnicy pieca). Spieki chłodzone z szybkością 65°C/min poddane zostały odpuszczaniu w temperaturze 200°C w czasie 60 i 240 minut. Spieczone kształtki poddano statycznej próbie rozciągania oraz próbie trójpunktowego zginania; przeprowadzone również zostały badania udarności oraz pomiary twardości. Badania mikrostruktury spiekanych stali prowadzono z wykorzystaniem mikroskopii świetlnej. W toku prowadzonych badań wykazano, że spiekanie kształtek w taniej i bezpiecznej atmosferze azotu (lub w atmosferach bogatych w azot) pozwala uzyskać zadowalające własności mechaniczne spieków, porównywalne z własnościami tych stali, wytwarzanych poprzez spiekanie w atmosferze wodoru.
Źródło:
Archives of Metallurgy and Materials; 2011, 56, 2; 293-303
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies