Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "hydrodynamic bearings" wg kryterium: Temat


Tytuł:
An experimental investigation conducted in order to determine bearing dynamic coefficients of two hydrodynamic bearings using impulse responses
Autorzy:
Breńkacz, Ł.
Żywica, G.
Powiązania:
https://bibliotekanauki.pl/articles/175435.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hydrodynamic bearings
bearing dynamic coefficients
experimental study
Opis:
The paper presents the experimental investigation carried out in order to identify bearing dynamic coefficients of two hydrodynamic bearings from impulse responses. In this method the stiffness, damping and mass coefficients of two hydrodynamic bearings were calculated in a single algorithm. For each rotational speed, were obtained 12 dynamic coefficients which enable to fully describe the dynamic state of the rotor. Exciting force signals, applied using an impact hammer were shown. Displacements of the shaft were measured by eddy current sensors. The measurements were carried out at various rotational speeds, including resonance speeds. The vibration amplitude in a resonance case increases significantly with time after the excitation was induced by an impact hammer. Excitations of the rotor with an impact hammer were recorded using a high-speed camera. These unique recordings and simultaneous analysis of the trajectory of the bearing journals depict the contact phenomena that occur during impulse excitation of the rotor.
Źródło:
Transactions of the Institute of Fluid-Flow Machinery; 2016, 133; 39-54
0079-3205
Pojawia się w:
Transactions of the Institute of Fluid-Flow Machinery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of dynamical properties of a 700 kW turbine rotor designed to operate in an ORC installation
Analiza właściwości dynamicznych wirnika turbiny 700 kW zaprojektowanej do wykorzystania w instalacji ORC
Autorzy:
Breńkacz, Ł.
Żywica, G.
Bogulicz, M.
Powiązania:
https://bibliotekanauki.pl/articles/328509.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
ORC turbine
rotor dynamic
hydrodynamic bearings
turbina ORC
dynamika wirnika
łożysko hydrodynamiczne
Opis:
The article presents the results of structural and dynamic analyses carried out for an axial-flow turbine with a capacity of 700 kW. The turbine is specifically designed for operation in an ORC (Organic Rankine Cycle) installation. The turbine rotor was supported by the following hydrodynamic bearings: two radial bearings and one bidirectional axial bearing. During numerical computation, both forces affecting the blade system and the rotor's torsional moments affecting the shaft were taken into account. Static, modal and forced vibration analysis of the turbine rotor was presented. The article also discusses the process of bearing selection and their geometry optimization to keep the rotor vibration level as low as possible. The computations of radial hydrodynamic bearings were carried out for various bearing clearance shapes. Madyn 2000 software and the in-house developed computer programs that are included in the MESWIR system were used during computer modeling.
W artykule przedstawiono wyniki analizy wytrzymałościowej i dynamicznej turbiny osiowej o mocy 700 kW. Turbina zaprojektowana została do pracy w obiegu ORC (Organic Rankine Cycle). Wirnik turbiny łożyskowany był za pomocą dwóch poprzecznych łożysk hydrodynamicznych oraz dwukierunkowego hydrodynamicznego łożyska osiowego. W obliczeniach numerycznych uwzględniono siły działające na układ łopatkowy oraz momenty skrętne działające na wirnik. Przedstawione zostały analiza statyczna, analiza modalna oraz analiza drgań wymuszonych. Zaprezentowany został proces doboru łożysk i optymalizacja ich geometrii pod kątem minimalizacji drgań wirnika. Wykonane zostały obliczenia poprzecznych łożysk hydrodynamicznych dla różnych kształtów szczeliny smarnej. Podczas pracy użyty został program Madyn 2000 oraz programy ze środowiska MESWIR opracowane w IMP PAN w Gdańsku.
Źródło:
Diagnostyka; 2016, 17, 2; 17-23
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The program of experimental research regarding concentration of magnetic particles Fe3 O4 in ferrofluid for slide journal bearing lubrication
Autorzy:
Miszczak, A.
Frycz, M.
Powiązania:
https://bibliotekanauki.pl/articles/246352.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
hydrostatic bearings
ferrofluid
position of test bearings
measuring the force of friction
magnetic field
hydrodynamic bearings
temperature distribution
Opis:
This paper presents the project of the test stand to determine the friction force, the relative eccentricity and temperature distribution m the slide journal bearing during the lubrication with ferrofluid or classic oil. The test stand is built on the basis of TUM 25 lathe's corps. There is the shaft with a diameter of journal d = 100 mm supported on two supports attached to the lathe's body. There is a sleeve in the housing with the electromagnets installed in the centre of this shaft. The housing of sleeve is loaded bv a transverse force with hydrostatic supports (cylindrical and flat one). Measurement of friction force is made by strain gauge force sensor Friction force is measured on the body shells. At the same time is performed measurement of both sleeve and journal displacements by four inductive displacement's sensor s and four whirl-stream ones to determine the relative eccentricity and displacement of sleeve axis towards oj the shaft axis. The slide bearing is supplied bv the ferrofluid which is thermatly stabilized in ultrathermostat. In the paper is shown particular plan for experimental research. These studies are intended to demonstrate the changes of relative eccentricity and temperature distribution in the bearing. Additionally are presented the changes of friction forces caused by the bearing surfaces shape and ferrolubricant with different concentrations of magnetic particles Fe3O4. The gap of slide bearing can be affected by the external longitudinal magnetic field with different ralues of magnetic field strength. The bearing may by loaded a transverse force varying stepwise, or continuously with values from a few to several thousand Newton. A/so, the rotational velocitv of Journal can be changed stepwise, or continuously from 0 to 6000 rpm using a programmable inverter.
Źródło:
Journal of KONES; 2010, 17, 2; 321-325
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Vibration control of rotors mounted in hydrodynamic bearings lubricated with magnetically sensitive oil by changing their load capacity
Autorzy:
Zapoměl, Jaroslav
Ferfecki, Petr
Powiązania:
https://bibliotekanauki.pl/articles/2086880.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
magnetically sensitive lubricant
controllable hydrodynamic bearings
controllable load capacity
rigid rotor
smar magnetycznie wrażliwy
kontrolowana pojemność
wirnik sztywny
Opis:
Rotors of rotating machines are often mounted in hydrodynamic bearings. Loading alternating between the idling and full load magnitudes leads to the rotor journal eccentricity variation in the bearing gap. To avoid taking undesirable operating regimes, its magnitude must be kept in a certain interval. This is offered by the hydrodynamic bearings lubricated with smart oils, the viscosity of which can be changed by the action of a magnetic field. A new design of a hydrodynamic bearing lubricated with magnetically sensitive composite fluid is presented in this paper. Generated in the electric coil, the magnetic flux passes through the bearing housing and the lubricant layer and then returns to the coil core. The action of the magnetic field on the lubricant affects the apparent fluid viscosity and thus the position of the rotor journal in the bearing gap. The developed mathematical model of the bearing is based on applying the Reynolds equation adapted for the case of lubricants exhibiting the yielding shear stress. The results of the performed simulations confirmed that the change of magnetic induction makes it possible to change the bearing load capacity and thus to keep the rotor journal eccentricity in the required range. The extent of control has its limitations. A high increase in the loading capacity can arrive at the rotor forced vibration’s loss of stability and induce large amplitude oscillation.
Źródło:
Bulletin of the Polish Academy of Sciences. Technical Sciences; 2021, 69, 6; e137988, 1--8
0239-7528
Pojawia się w:
Bulletin of the Polish Academy of Sciences. Technical Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of Rabinovitsch fluid model to pivoted curved slider bearings
Zastosowanie modelu płynu Rabinowitch’a do uchylnych łożysk ślizgowych z zakrzywionym ślizgaczem
Autorzy:
Singh, U. P.
Powiązania:
https://bibliotekanauki.pl/articles/139505.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
hydrodynamic bearings
hydrodynamic friction
hydrodynamic lubrication
load carrying capacity
Rabinowitsch fluid model
VI Improvers
łożyska hydrodynamiczne
tarcie hydrodynamiczne
smarowanie hydrodynamiczne
nośność
model płynu Rabinowitcha
Dodatki VI
Opis:
In the present theoretical analysis, the combined effects of slider curvature and non-Newtonian pseudoplastic and dilatant lubricants (lubricant blended with viscosity index improver) on the steady and dynamic characteristics of pivoted curved slider bearings have been investigated for Rabinowitsch fluid model. The modified Reynolds equations have been obtained for steady and damping states of bearing. To solve the modified Reynolds equations, perturbation theory has been adopted. The results for the steady state characteristics (steady state film pressure, load carrying capacity and centre of pressure) and dynamic characteristics (dynamic damping and dynamic stiffness) have been calculated numerically for various values of viscosity index improver using Mathematica. In comparison with the Newtonian lubricants, higher values of film pressure, load carrying capacity, dynamic damping and dynamic stiffness have been obtained for dilatant lubricants, while the case was reversed for pseudoplastic lubricants. Significant variations in the bearing characteristics have been observed for even small values of pseudoplastic parameter, that is, with the non-Newtonian dilatant and pseudoplastic behaviour of the fluid.
W przedstawionej analizie teoretycznej badano, przy wykorzystaniu modelu płynu Rabinowitch’a, łączny wpływ krzywizny ślizgacza i smaru o właściwościach pseudoplastycznych, nieniutonowskich, o odwróconej plastyczności (smar zmieszany ze środkiem poprawiającym wskaźnik lepkości) na charakterystyki w stanie ustalonym i warunkach dynamicznych uchylnego, łożyska ślizgowego. Zmodyfikowane równania Reynoldsa otrzymano dla stanów ustalonych i tłumionych łożyska. W celu rozwiązania zmodyfikowanych równań Reynoldsa zastosowano teorie perturbacji. Wielkości charakterystyczne dla stanu ustalonego (ciśnienie smaru w stanie ustalonym, nośność i środek ciśnienia) i charakterystyki dynamiczne (tłumienie dynamiczne i sztywność dynamiczna) zostały wyznaczone numerycznie, przy użyciu pakietu Mathematica, dla różnych wartości wskaźnika poprawy lepkości. W porównaniu ze smarami o właściwościach cieczy newtonowskiej, dla smaru o odwróconej plastyczności uzyskano wyższe wartości ciśnienia w filmie, większą nośność, lepsze tłumienie dynamiczne i dynamiczną sztywność. Sytuacja wygladała odwrotnie w przypadku smarów pseudoplastycznych. Znaczące zmiany charakterystyk łożyska, związane z nie-newtonowskim, pseudoplastycznym zachowaniem płynu o odwróconej plastyczności, zaobserwowano już przy małych wartościach parametru pseudoplastyczności.
Źródło:
Archive of Mechanical Engineering; 2013, LX, 2; 247-267
0004-0738
Pojawia się w:
Archive of Mechanical Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of the Teager-Kaiser energy operator in diagnostics of a hydrodynamic bearing
Zastosowanie operatora energetycznego Teagera-Kaisera w diagnostyce łożyska hydrodynamicznego
Autorzy:
Blaut, Jędrzej
Breńkacz, Łukasz
Powiązania:
https://bibliotekanauki.pl/articles/1841930.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
Teager-Kaiser energy operator
rotor unbalance
hydrodynamic bearings
rotor dynamics
operator energetyczny Teagera-Kaisera
niewyważenie wirnika
łożyska hydrodynamiczne
dynamika wirnika
Opis:
The paper presents the use of the Teager-Kaiser energy operator (TKEO) to evaluate the state of rotor unbalance. The method was developed in 1990 by Kaiser and involves a simple calculation of signal energy. It has been used before in diagnostics, e.g. during the evaluation of instability of hydrodynamic bearings and as a diagnostic symptom of gearbox damage. This paper is the first to present the use of the Teager-Kaiser method to evaluate the rotor unbalance in hydrodynamic bearings.
W artykule przedstawiono zastosowanie operatora energetycznego Teagera-Kaisera (TKEO) do oceny stanu niewyważenia wirnika. Metoda ta opracowana została w 1990 roku przez Kaisera i polega na prostym obliczeniu energii sygnału. Wykorzystywana była już wcześniej w diagnostyce np. przy ocenie niestabilności łożysk hydrodynamicznych oraz jako symptom diagnostyczny uszkodzenia przekładni. W artykule tym po raz pierwszy przedstawiono możliwość wykorzystania metody Teagera-Kaisera do oceny niewyważenia wirnika pracującego na łożyskach hydrodynamicznych.
Źródło:
Eksploatacja i Niezawodność; 2020, 22, 4; 757-765
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Hydrodynamic thrust bearings with polymer lining
Hydrodynamiczne łożyska wzdłużne z polimerową warstwą ślizgową
Autorzy:
Wodtke, M.
Powiązania:
https://bibliotekanauki.pl/articles/187939.pdf
Data publikacji:
2016
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
hydrodynamic thrust bearings
tilting-pad bearings
polymer lining
hydrodynamiczne łożyska wzdłużne
łożyska z wahliwymi segmentami
pokrycia polimerowe
Opis:
Polymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operations and research, they have not become widespread in industrial applications. This fact may be surprising, considering the conclusions that have been publisher concerning bearing operation and design. This paper summarizes the current state of the art of the tilting-pad thrust bearings with a polymer lining of pad sliding surfaces. Bearing design and the most commonly used polymeric materials are described. The results of the latest theoretical and experimental researches by both bearing manufacturers and at scientific centres are presented. Observed properties of the bearings with polymer lining were compared to the properties of the bearings covered with Babbitt, which is the most frequently material used as lining for hydrodynamic bearings.
Pokrycia polimerowe powierzchni ślizgowych łożysk hydrodynamicznych są stosowane z sukcesem od ponad 50 lat. Mimo tak długiej historii eksploatacji oraz badań nie znalazły one, jak dotąd, szerokiego zastosowania przemysłowego. Fakt ten może dziwić, biorąc pod uwagę wnioski płynące z eksploatacji oraz dostępnych w literaturze badań łożysk tej odmiany konstrukcyjnej. W niniejszej pracy podsumowano stan aktualnej wiedzy dotyczącej hydrodynamicznych łożysk wzdłużnych z wahliwymi segmentami z pokryciem powierzchni ślizgowej warstwą polimeru. Opisano konstrukcję łożyska oraz scharakteryzowano najczęściej stosowane materiały polimerowe na pokrycia łożysk. Omówiono wyniki najnowszych badań teoretycznych oraz doświadczalnych prowadzonych zarówno przez producentów, jak i w ośrodkach naukowych. Wskazano również na zaobserwowane różnice we właściwościach łożysk tej odmiany konstrukcyjnej w porównaniu z łożyskami z najczęściej stosowanym pokryciem warstwy ślizgowej stopem łożyskowym.
Źródło:
Tribologia; 2016, 268, 4; 225-237
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of the exposure-in-oil on the contact angle of the polymers forming sliding layers in hydrodynamic bearings
Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych
Autorzy:
Zorn, J.
Wasilczuk, M.
Powiązania:
https://bibliotekanauki.pl/articles/971605.pdf
Data publikacji:
2016
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
hydrodynamic thrust bearings
polymer-sliding layers
contact angle
wetting
łożyska hydrodynamiczne wzdłużne
polimerowe warstwy ślizgowe
kąt zwilżania
zwilżanie
Opis:
Polymers used as the sliding layers of hydrodynamic thrust bearings are typically thermoplastics characterized by relatively high values of contact angles when compared with metals. Metals, including Babbitt, or other bearing alloys, are characterized by low values of the contact angles. The lower the angle, the better the surface is wetted. Plastics used in tribological pairs to ensure a lower coefficient of friction, that is, for example, polytetrafluoroethylene (PTFE) or its composites, have several times higher contact angles compared to the bearing alloys. The research described below shows the effect of the exposure-in-oil contact angle of the polymer layer applied on a hydrodynamic sliding bearing. The conducted study showed the beneficial effects of oil on the reduction of the contact angle.
Polimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić jak niższy współczynnik tarcia, czyli na przykład politetra-fluoroetylen lub jego kompozyty cechują kilkukrotnie wyższe wartości kątów zwilżania w porównaniu ze stopami łożyskowymi. W opisanym poniżej badaniu przedstawiono wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych. Przeprowadzone badanie pokazało korzystny wpływ oleju na obniżenie kąta zwilżania.
Źródło:
Tribologia; 2016, 269, 5; 219-227
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
CFD analysis of nano-lubricated journal bearing considering variable viscosity and elastic deformation effects
Autorzy:
Kadhim, Zainab H.
Ahmed, Saba Y.
Abass, Basim A.
Powiązania:
https://bibliotekanauki.pl/articles/2096173.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Polskie Towarzystwo Diagnostyki Technicznej PAN
Tematy:
hydrodynamic journal bearings
computational fluid dynamics
thermohydrodynamic lubrication
nano-lubricant
elastic deformation
hydrodynamika
łożyska ślizgowe
numeryczna mechanika płynów
smarowanie hydrodynamiczne
odkształcenie sprężyste
Opis:
The main objective of the present work is to study the behavior of Nano-lubricated journal bearing considering elasticity and variable viscosity effects. A mathematical model for a journal bearing is employed using three-dimensional computational fluid dynamics. The study is implemented for a journal bearing with laminar flow and smooth surfaces lubricated with pure oil as well as lubricants containing different concentrations of Al2O3 Nano-particles. The dependence of the oil viscosity on the temperature is considered by using the modified Krieger Dougherty model. Pressure, temperature and elastic deformation in addition to the bearing load-carrying capacity of the bearing working under different eccentricity ratios (0.1-0.6) have been studied. The mathematical model is confirmed by comparing the results of the pressure and temperature distributions obtained in the current work with those obtained by Ferron et al.(1983) for a bearing lubricated with pure oil. Also, the pressure obtained for the Nano-lubricated bearing of the present work is validated with that obtained by Solighar (2015). The results are found in good agreement with a maximum deviation not exceeding 5%. The obtained results show that the oil film pressure increases by about 17.9% with a slight decrease in oil film temperature and friction coefficient.
Źródło:
Diagnostyka; 2022, 23, 1; 1--8
1641-6414
2449-5220
Pojawia się w:
Diagnostyka
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Calculations of tilting-pad thrust bearings
Obliczenia łożysk ślizgowych wzdłużnych z segmentami wahliwymi
Autorzy:
Murdzia, Edward
Strzelecki, Stanisław
Powiązania:
https://bibliotekanauki.pl/articles/2055615.pdf
Data publikacji:
2021
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
hydrodynamic lubrication
thrust bearings
static characteristics
smarowanie hydrodynamiczne
łożyska wzdłużne
charakterystyka statyczna
Opis:
The application of thrust bearings in different engineering designs generates problems of thermal state, which generates the wear of the fixed or tilting pads of bearings. These problems can be avoided by means of proper methods and numerical algorithms of calculations of the bearing static characteristics, including the maximum oil film temperature. The knowledge of thermal state of bearings should assure safe, reliable, and durable bearing operation and is important for the designers of thrust bearings. This paper presents the results of calculations of some static characteristics of a tilting-pad thrust bearing, including its maximum oil film temperature. Numerical solution by means of finite differences was applied for the solution of geometry, Reynolds, energy, and viscosity equations. Adiabatic oil film laminar flow in the bearing gap was considered. The developed code of the computation of bearing performances creates a tool that leads to the solution of thermal problems. Different values of operating speeds were assumed.
Stosowanie ślizgowych łożysk wzdłużnych wiąże się z problemami stanu cieplnego i zużycia stałych lub wahliwych segmentów łożyska. Zastosowanie odpowiednich metod obliczeniowych i algorytmów numerycznych charakterystyk statycznych łożyska włącznie z maksymalną temperaturą filmu smarowego pozwala na uniknięcie problemów eksploatacyjnych. Znajomość stanu cieplnego łożyska powinna zapewnić bezpieczną, niezawodną, trwałą jego eksploatację oraz jest ważna dla konstruktorów łożysk wzdłużnych. W artykule przedstawiono wyniki obliczeń niektórych charakterystyk statycznych łożyska wzdłużnego z segmentami wahliwymi. Podstawowe równania teorii smarowania hydrodynamicznego Reynoldsa, energii i lepkości oraz geometrii rozwiązano metodą iteracyjną. Opracowany algorytm obliczeń numerycznych łożyska z nieizotermicznym filmem smarowym stwarza narzędzie pozwalające na rozwiązywanie problemów cieplnych łożysk wzdłużnych. Założono różne wartości prędkości obrotowych. Przyjęto adiabatyczny, laminarny model filmu smarowego.
Źródło:
Tribologia; 2021, 298, 4; 27--36
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of the Misalignment of Journal and Sleeve Axis on the Operation of Turbo Unit Journal Bearings
Wpływ niewspółosiowości osi czopa i panewki na pracę łożysk ślizgowych turbozespołu
Autorzy:
Strzelecki, Stanisław
Powiązania:
https://bibliotekanauki.pl/articles/1857796.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
hydrodynamic lubrication
multilobe journal bearings
oil film temperature
smarowanie hydrodynamiczne
wielopowierzchniowe łożyska ślizgowe
temperatura filmu smarowego
Opis:
In journal bearings the misalignment of the journal and sleeve axis causes a load concentration on their edges, mixed lubrication conditions, an increase in the bearing temperature, rotor instability, and intensive wear of mating parts. The rotating machines are controlled by means of the temperature and vibration transducers, which are placed in the middle plain of the bearing housing. This arrangement of transducers gives no information about the real distance between the journal surface and bearing edges, and, in case of misaligned shaft, it has crucial meaning for the correct operation of turbo unit. This paper presents the theoretical and some experimental results of turbo unit journal bearing operating in misaligned conditions. The results point out the necessity of the precise control of the lubricating gap and the temperature generated on the bearing edges. It was also found that the increase in misalignment also generates an increase in power loss.
W warunkach niewspółosiowości osi czopa i panewki w łożysku występuje koncentracja nacisków na jego krawędziach, tarcie mieszane oraz zwiększone zużycie i niestateczna praca. W maszynie wirnikowej tempe ratura pracy łożysk oraz ich drgania kontrolowane są czujnikami umieszczonymi w płaszczyźnie środkowej obudowy łożyska. Brak jest danych o rzeczywistej odległości między powierzchnią ślizgową łożyska i jego krawędziami. W przypadku niewspółosiowości takie informację są bardzo ważne dla prawidłowej pracy tur bozespołu. Wyniki badań teoretycznych oraz pomiarów przemieszczeń na rzeczywistym obiekcie, jakim jest turbozespół wskazują na konieczność sprawdzania temperatury na krawędziach łożysk. Wzrost niewspółosiowości osi czopa i panewki powoduje m.in. wzrost strat mocy.
Źródło:
Tribologia; 2020, 293, 5; 73-84
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Static Characteristics of Offset 8-Lobe Journal Bearings
Charakterystyki statyczne 8-powierzchniowych łożysk ślizgowych z przesuniętymi segmentami
Autorzy:
Strzelecki, Stanisław
Powiązania:
https://bibliotekanauki.pl/articles/2055630.pdf
Data publikacji:
2021
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
hydrodynamic lubrication
multilobe offset journal bearings
static characteristics
smarowanie hydrodynamiczne
wielopowierzchniowe łożyska ślizgowe offset
charakterystyka statyczna
Opis:
The 8-lobe journal bearings have found application in the bearing systems of spindles of grinding machines. The design of bearings and the large number of lobes and oil grooves assures good cooling conditions of bearing. These bearings can be manufactured as the bearings with cylindrical, non-continuous operating surfaces separated by six lubricating grooves, bearings with the pericycloidal shape of the bearing bore, and as offset journal bearing. This paper presents the results of the computation of static characteristics of an offset 8-lobe journal bearing operating under the conditions of an aligned axis of journal and bush, adiabatic oil film, and at the static equilibrium position of journal. Different values of bearing length to diameter ratio, relative clearance, and lobe relative clearance were assumed. Reynolds' energy and viscosity equations were solved by means of an iterative procedure. Adiabatic oil film, laminar flow in the bearing gap, and aligned orientation of journal in the bearing were considered.
Łożyska ślizgowe 8-powierzchniowe stosowane są w układach łożyskowania wrzecion szlifierek. Konstrukcja tych łożysk i znaczna liczba powierzchni ślizgowych oraz rowków smarowych zapewniają dobre warunki chłodzenia. Łożyska te mogą być wykonywane z segmentami o powierzchni kołowej, zarysie nieciągłym lub ciągłym; z przesuniętymi segmentami, a powierzchnie ślizgowe są oddzielone rowkami smarowymi. Artykuł przedstawia obliczenia charakterystyk statycznych łożysk 8-powierzchniowych z przesuniętymi segmentami pracujących w warunkach równoległych osi czopa i panewki i statycznego położenia równowagi czopa. Założono różne wartości względnej długości łożyska, luzu łożyskowego i względnego luzu segmentu. Równanie Reynoldsa, energii i lepkości rozwiązano metodą różnic skończonych autorskim kodem numerycznym. Przyjęto adiabatyczny i laminarny model przepływu środka smarowego w szczelinie smarowej.
Źródło:
Tribologia; 2021, 295, 1; 39--51
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of oil grooves on the static characteristics of cylindrical 3-lobe journal bearings
Wpływ rowków smarowych na charakterystyki statyczne cylindrycznego łożyska 3-powierzchniowego
Autorzy:
Strzelecki, S.
Kumycz, K.
Powiązania:
https://bibliotekanauki.pl/articles/191157.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
theory of hydrodynamic lubrication
multilobe journal bearings
oil grooves
teoria smarowania hydrodynamicznego
łożyska ślizgowe
rowki smarowe
Opis:
Multilobe journal bearings with three operating lobes with cylindrical profiles and separated by oil grooves are applied in different types of rotating machinery. The design of 3-lobe journal bearings in relation to the number of lobes and oil grooves affects bearing static characteristics. This paper describes the results of the calculations of static characteristics of 3-lobe cylindrical journal bearings in relation to the different angular widths of oil grooves. The bases for the static characteristics are the oil film pressure, temperature, and viscosity distributions. The iterative solution of oil film geometry, Reynolds, energy, and viscosity equations are used to determine the required distributions and the load capacity of bearings. Laminar, adiabatic oil film, and the static equilibrium position of journal were assumed.
Układy łożyskowe maszyn wirnikowych charakteryzują się stosowaniem łożysk wielopowierzchniowych [L. 1–8]. Konstrukcja łożyska, w tym liczba powierzchni roboczych, rowków smarowych i ich szerokość kątowa wpływają na jego charakterystyki statyczne i dynamiczne. Charakterystyki statyczne obejmują rozkłady ciśnienia, temperatury, lepkości filmu smarowego, minimalną grubość, maksymalną temperaturę i ciśnienie w filmie smarowym, przepływ środka smarowego oraz straty tarcia. Program obliczeniowy charakterystyk łożyska umożliwia wyznaczenie charakterystyk statycznych łożyska, m.in. wpływ wielkości rowków smarowych na charakterystyki łożyska. Przedstawiono wyniki badań teoretycznych wpływu kątowej szerokości rowka smarowego na charakterystyki statyczne 3-powierzchniowego, cylindrycznego łożyska ślizgowego. Równania Reynoldsa, energii i lepkości rozwiązano metodą różnic skończonych, zakładając laminarny, adiabatyczny przepływ środka smarowego w łożysku o skończonej długości oraz statyczne położenie równowagi czopa.
Źródło:
Tribologia; 2013, 3; 119-131
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Maximum oil film temperature of a 4-lobe journal bearing with the lobes of small angular length
Maksymalna temperatura 4-segmentowego łożyska z częściowymi powierzchniami ślizgowymi
Autorzy:
Strzelecki, S.
Powiązania:
https://bibliotekanauki.pl/articles/189736.pdf
Data publikacji:
2017
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
hydrodynamic lubrication
multilobe journal bearings
oil film temperature
smarowanie hydrodynamiczne
wielopowierzchniowe łożyska ślizgowe
temperatura filmu smarowego
Opis:
Multilobed journal bearings with the lobes of small angular length are often applied in the bearing systems of grinding machine spindles, which is the most important assembly in the grinding machine. The safe operation of such bearings at proper oil film temperature can be assured by the knowledge of thermal state of bearing and its maximum temperature. This paper presents the results of the calculations of some static characteristics of a 4-lobe bearing with the lobes of small angular length and particularly its maximum oil film temperature. The oil film pressure, temperature, and viscosity fields were obtained by an iterative solution of the Reynolds', energy, and viscosity equations. Adiabatic, laminar oil film and the static equilibrium position of journal were assumed.
W ramach opisanych badań wyznaczono rozkłady ciśnienia, temperatury w filmie smarowym 4-powierzchnowego klasycznego łożyska. Wyznaczono maksymalne temperatury filmu smarowego dla założonych parametrów łożysk. Obliczenia przeprowadzono metodą różnic skończonych, rozwiązując równania Reynoldsa, energii i lepkości dla przypadku adiabatycznego filmu. Kod obliczeń numerycznych pozwala na analizę różnych parametrów geometrycznych i eksploatacyjnych łożyska, w tym ciśnienia zasilania środkiem smarowym. Stwierdzono wpływ zasilania ciśnieniowego na wszystkich krawędziach łożyska na charakterystyki statyczne. Zamiany względnego luzu łożyskowego nieznacznie wpływają na przemieszczenie czopa i minimalną grubość filmu smarowego.
Źródło:
Tribologia; 2017, 275, 5; 87-92
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Operating temperatures of the bearing system of grinder spindle
Temperatury pracy układu łożysk wrzeciennika szlifierki
Autorzy:
Strzelecki, S.
Socha, Z.
Powiązania:
https://bibliotekanauki.pl/articles/189910.pdf
Data publikacji:
2011
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
teoria smarowania hydrodynamicznego
łożyska ślizgowe
temperatura filmu smarowego
theory of hydrodynamic lubrication
journal bearings
oil film temperature
Opis:
The ground for the safe operation of multilobe journal bearings at proper oil film temperature is the full knowledge of bearing thermal performances particularly the oil film temperature distribution and its maximum value. This paper describes the theoretical and experimental investigation into the operating temperatures of pericycloid, 3-lobe journal bearings supporting the spindle of grinding machine. The oil film pressure, temperature and viscosity fields have been obtained by iterative solution of the Reynolds', energy and viscosity equations. Adiabatic, laminar oil film and the static equilibrium position of the journal were assumed. Experimental investigation consisted in the measurements of temperatures in the bearings.
Wielopowierzchniowe łożyska ślizgowe [L. 1-3], stosowane są w lekko obciążonych, wysokoobrotowych maszynach wirnikowych. W praktyce stosowane są łożyska ślizgowe 3-powierzchniowe z perycykloidalnym zarysem panewki (łożysko "falowe" – "wave") [L. 2, 3]. Przykładem ich zastosowania jest układ łożyskowania wrzeciennika szlifierki lub łożyska satelitów przekładni planetarnej [L. 3]. W części teoretycznej wyznaczono rozkłady ciśnienia i temperatury w filmie smarowym 3-powierzchnowego łożyska z zarysem perycykloidalnym rozwiązując równania Reynoldsa, energii i lepkości środka smarowego. Obliczenia przeprowadzono metodą różnic skończonych [L. 2] dla przypadku adiabatycznego filmu. W doświadczalnej części badań pomierzono temperatury na powierzchniach roboczych 3-powierzchniowych łożysk z zarysem perycykloidalnym. Stanowisko badawcze skonstruowano na bazie rzeczywistego układu łożysk ślizgowych [L. 4]. Każde z łożysk ślizgowych wyposażono w trzy czujniki temperatury umieszczone w środkowej płaszczyźnie łożyska w odległości około 0,2 mm od powierzchni roboczej panewki. Pomierzone wartości temperatur porównano z wartościami wyznaczonym teoretycznie.
Źródło:
Tribologia; 2011, 2; 157-167
0208-7774
Pojawia się w:
Tribologia
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies