Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

English (EN)·Polski (PL)·Yкраїнський (UK)
Przejdź do strony domowej biblioteki Centralna Biblioteka Wojskowa Link otwiera się w nowym oknie Logo biblioteki Prolib Integro - strona głównaCentralna Biblioteka Wojskowa

Wyszukujesz frazę "Wang, J. P." wg kryterium: Autor

  Lista filtrów
Wyrównaj
Wyświetlanie 1-15 z 54
Tytuł:
Recovery of Pig Iron from Copper Smelting Slag by Reduction Smelting
Autorzy:
Erdenebold, U.
Choi, M.-H.
Wang, J.-P.
Powiązania:
https://bibliotekanauki.pl/articles/355067.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
copper slag
reduction
pig iron
fayalite
recovery
Opis:
Copper slag is a by-product obtained during smelting and refining of copper. Copper smelting slag typically contains about 1 wt.% copper and 40 wt.% iron depending upon the initial ore quality and the furnace type. Main components of copper slag are iron oxide and silica. These exist in copper slag mainly in the form of fayalite (2FeO ·SiO2 ). This study was intended to recover pig iron from the copper smelting slag by reduction smelting method. At the reaction temperature of below 1400°С the whole copper smelting slag was not smelted, and some agglomerated, showing a mass in a sponge form. The recovery behavior of pig iron from copper smelting slag increases with increasing smelting temperature and duration. The recovery rate of pig iron varied greatly depending on the reaction temperature.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1793-1798
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Recovery Of Nickel From Spent Nickel-Cadmium Batteries Using A Direct Reduction Process
Odzysk niklu z zużytych baterii niklowo-kadmowych za pomocą bezpośredniej redukcji
Autorzy:
Shin, D. J.
Joo, S.-H.
Wang, J.-P.
Shin, S. M.
Powiązania:
https://bibliotekanauki.pl/articles/355948.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
spent nickel-cadmium batteries
direct reduction
recycling
heat treatment
zużyte baterie niklowo-kadmowe
redukcja bezpośrednia
recykling
obróbka cieplna
Opis:
Most nickel is produced as Ferro-Nickel through a smelting process from Ni-bearing ore. However, these days, there have been some problems in nickel production due to exhaustion and the low-grade of Ni-bearing ore. Moreover, the smelting process results in a large amount of wastewater, slag and environmental risk. Therefore, in this research, spent Ni-Cd batteries were used as a base material instead of Ni-bearing ore for the recovery of Fe-Ni alloy through a direct reduction process. Spent Ni-Cd batteries contain 24wt% Ni, 18.5wt% Cd, 12.1% C and 27.5wt% polymers such as KOH. For pre-treatment, Cd was vaporized at 1024K. In order to evaluate the reduction conditions of nickel oxide and iron oxide, pre-treated spent Ni-Cd batteries were experimented on under various temperatures, gas-atmospheres and crucible materials. By a series of process, alloys containing 75 wt% Ni and 20 wt% Fe were produced. From the results, the reduction mechanism of nickel oxide and iron oxide were investigated.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1365-1370
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Recovery Of Electrodic Powder From Spent Lithium Ion Batteries (LIBs)
Odzysk proszku elektrodowego z zużytych akumulatorów litowo-jonowych
Autorzy:
Shin, S. M.
Jung, G. J.
Lee, W-J.
Kang, C. Y.
Wang, J. P.
Powiązania:
https://bibliotekanauki.pl/articles/354084.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
lithium ion battery
electrodic powder
cobalt
lithium
thermal treatment
bateria litowo-jonowa
proszek elektrodowy
kobalt
lit
obróbka termiczna
Opis:
This study was focused on recycling process newly proposed to recover electrodic powder enriched in cobalt (Co) and lithium (Li) from spent lithium ion battery. In addition, this new process was designed to prevent explosion of batteries during thermal treatment under inert atmosphere. Spent lithium ion batteries (LIBs) were heated over the range of 300°C to 600°C for 2 hours and each component was completely separated inside reactor after experiment. Electrodic powder was successfully recovered from bulk components containing several pieces of metals through sieving operation. The electrodic powder obtained was examined by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), and atomic absorption spectroscopy (AA) and furthermore image of the powder was taken by scanning electron microscopy (SEM). It was finally found that cobalt and lithium were mainly recovered to about 49 wt.% and 4 wt.% in electrodic powder, respectively.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1145-1149
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Recovery Of Electrodic Powder From Spent Nickel-Metal Hydride Batteries (NiMH)
Odzyskiwanie proszku elektrodowego ze zużytych akumulatorów niklowo-wodorkowych (NiMH)
Autorzy:
Shin, S. M.
Shin, D. J.
Jung, G. J.
Kim, Y. H.
Wang, J. P.
Powiązania:
https://bibliotekanauki.pl/articles/356110.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nickel-metal hybride (NiMH)
electrodic powder
nickel
rare earth elements (REE)
thermal treatment
akumulator niklowo-wodorkowy
proszek elektrodowy
nikiel
pierwiastki ziem rzadkich
obróbka termiczna
Opis:
This study was focused on recycling process newly proposed to recover electrodic powder enriched in nickel (Ni) and rare earth elements (La and Ce) from spent nickel-metal hydride batteries (NiMH). In addition, this new process was designed to prevent explosion of batteries during thermal treatment under inert atmosphere. Spent nickel metal hydride batteries were heated over range of 300°C to 600°C for 2 hours and each component was completely separated inside reactor after experiment. Electrodic powder was successfully recovered from bulk components containing several pieces of metals through sieving operation. The electrodic powder obtained was examined by X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) and image of the powder was taken by scanning electron microscopy (SEM). It was finally found that nickel and rare earth elements were mainly recovered to about 45 wt.% and 12 wt.% in electrodic powder, respectively.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1139-1143
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Study On The Fabrication Of Iron Powder From Forging Scale Using Hydrogen
Próby wytwarzanie proszku żelaza metodą redukcji zgorzeliny pochodzącej z procesów kucia za pomocą wodoru
Autorzy:
Shin, S. M.
Lee, D.-W.
Yun, J.-Y.
Kang, Ch.-Y.
Wang, J.-P.
Powiązania:
https://bibliotekanauki.pl/articles/350946.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
forging scale
hydrogen partial pressure
hematite
iron powder
kucie za pomocą wodoru
hematyt
redukcja zgorzeliny
proszek żelaza
Opis:
This study was conducted to investigate the effect of hydrogen content, temperature, reaction time for the reduction of forging scale which is mainly composed of hematite (Fe2O3). All reductive reactions were performed over the temperature range of 700 to 1200°C as well as 0.1 to 1 atm of hydrogen partial pressures. The results showed that the mechanism for the reduction of iron oxides using hydrogen gas was not a simple process, but proceeded in multiple reduction stages thermodynamically. The iron oxide was almost completely reduced to metallic iron powder with 91 wt.% of iron content in the forging scale at 0.1 atm of hydrogen partial pressure. The content of iron was however found to be increased with increasing hydrogen partial pressure from 0.1 to 1 atm with regardless of temperatures. The metallic iron powder was obtained with the mean size of 100 μm and more porous structure was observed.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 2B; 1547-1549
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of upper extremity position on EMG signal measures calculated in time, frequency and time-frequency domains
Autorzy:
Wang, J.
Bartuzi, P.
Roman-Liu, D.
Powiązania:
https://bibliotekanauki.pl/articles/306619.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
upper extremity
EMG
position
time-frequency domain
postawa ciała
biomechanika
Opis:
The aim of this study was to investigate the relationship between time-frequency, time and frequency measures when considering various upper extremity positions below the level of the shoulder and in trapezius as well as deltoideus muscles. During the experiment, 15 subjects performed a task that involved screwing and unscrewing a screw cap on a board in six different locations, i.e., there were six upper extremity positions. Variables were calculated in the time, frequency and time-frequency domains on a recorded EMG signal. The results showed that parameters analyzed in the time-frequency domain were more sensitive to changes in position than parameters analyzed in the frequency domain.
Źródło:
Acta of Bioengineering and Biomechanics; 2013, 15, 4; 83-91
1509-409X
2450-6303
Pojawia się w:
Acta of Bioengineering and Biomechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Theoretical analytical solution of deformation and stress distribution of underground gas storage cavern in bedded salt rock
Autorzy:
Xie, P.
Wen, H. J.
Wang, G. J.
Hu, J.
Powiązania:
https://bibliotekanauki.pl/articles/230968.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
złoża soli kamiennej
analiza teoretyczna
funkcja wypierania Love'a
zasada zgodności sprężysto-lepkosprężystej
różnica skończona trójwymiarowa wyraźna
bedded salt rock
theoretical analysis
Love displacement function
elastic-viscoelastic correspondence principle
three-dimensional explicit finite-difference
Opis:
The main purpose of the study is to investigate the mechanical properties around an underground gas storage cavern in bedded salt rock. Firstly, considering the characteristics of the salt rock formation in China, the mechanical model was simplified into a hollow cylinder, which containing non-salt interlayer. In terms of elastic theory, Love displacement function was developed, and the elastic general solution of stress and deformation components were obtained after determining the undetermined coefficients. Under the same condition, numerical simulation was carried out. The validity of the elastic general solution is verified by comparing to numerical simulation results. Furthermore, Based on the feasible general elastic solution, viscoelastic solution was obtained through Laplace transformation and inverse Laplace transform, which could provide reference for the study on the stability and tightness of underground gas storage carven during operation to some extent.
Źródło:
Archives of Civil Engineering; 2018, 64, 4/I; 37-53
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Renewable warranty policy for multiple-failure-mode product considering different maintenance options
Polityka odnawiania gwarancji dla produktówo mnogich przyczynach uszkodzeń uwzględniająca różne opcje obsługi
Autorzy:
Li, X.
Jia, Y.
Wang, P.
Zhao, J.
Powiązania:
https://bibliotekanauki.pl/articles/301949.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
multiple failure modes
renewing warranty
preventive maintenance
warranty cost
product availability
upgrading maintenance
mnogie przyczyny uszkodzeń
odnowienie gwarancji
obsługa profilaktyczna
koszty gwarancji
gotowość produktu
konserwacja modernizacyjna
Opis:
Along with the advancement of manufacturing techniques, the quality of the spares for product is likely to be improved during the warranty period. There can be two types of spares, i.e. low-quality spares and high-quality spares for replacement maintenance. And the manufacturers (customers) may have to decide whether or not to provide (buy) the warranty considering upgrading maintenance. This paper presents a renewing warranty policy considering three maintenance options for products with multiple failure modes. The cost and availability models of these maintenance options are proposed. Of these options, upgrading maintenance is taken into account with the assumption that the warrantied item will be upgraded one time during the warranty cycle. After upgrading maintenance, the high-quality spares are used to replace the failed item. By minimizing the ratio between cost and availability of the product, the optimal upgrading opportunity is obtained. In the numerical example, the results of these options are presented. Monte Carlo simulation results are compared with the analytical results to demonstrate the correctness and efficiency of the proposed models considering upgrading maintenance. The renewing warranty policy considering upgrading maintenance policy is compared with the one without considering upgrading maintenance. The results show that the former is better than the latter in some cases. The sensitivity of the cost model and availability model to different parameters is analyzed at last.
Wraz z postępem techniki produkcji, wzrasta prawdopodobieństwo, że jakość części zamiennych do produktu ulegnie poprawie w przeciągu okresu gwarancyjnego. Istnieją dwa rodzaje części zamiennych: części zamienne niskiej i wysokiej jakości. Producenci (klienci) mogą być zmuszeni podjąć decyzję czy objąć produkt gwarancją (wykupić gwarancję) zapewniającą konserwację modernizacyjną. W artykule przedstawiono politykę odnawiania gwarancji z uwzględnieniem trzech różnych opcji obsługi produktów narażonych na mnogie przyczyny uszkodzeń. Zaproponowano modele kosztów i gotowości dla omawianych opcji obsługi. Spośród badanych opcji, do dalszej analizy wybrano konserwację modernizacyjną zakładającą, że element podlegający gwarancji zostanie poddany jednokrotnej modernizacji podczas cyklu gwarancyjnego. Po wykonaniu konserwacji modernizacyjnej, uszkodzony element zastępuje się częściami zamiennymi wysokiej jakości. Minimalizując stosunek kosztów do gotowości produktu, uzyskuje się optymalną możliwość modernizacji Przykład numeryczny przedstawia wyniki uzyskane dla omawianych opcji. Wyniki symulacji Monte Carlo porównano z wynikami analitycznymi w celu wykazania prawidłowości i efektywności proponowanych modeli uwzględniających konserwację modernizacyjną. Politykę odnawiania gwarancji uwzględniającą konserwację modernizacyjną porównano z polityką, która takiej konserwacji nie uwzględnia. Wyniki pokazują, że pierwsza z tych opcji jest w niektórych przypadkach korzystniejsza od drugiej. Badania wieńczy analiza czułości modelu kosztów i modelu gotowości na różne parametry.
Źródło:
Eksploatacja i Niezawodność; 2015, 17, 4; 551-560
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Structural and Optical Properties of ZnO Nanowires Doped with Magnesium
Autorzy:
Zhuang, H.
Wang, J.
Liu, H.
Li, J.
Xu, P.
Powiązania:
https://bibliotekanauki.pl/articles/1505046.pdf
Data publikacji:
2011-06
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
61.46.Km
61.72.uj
81.15.Gh
78.67.-n
Opis:
ZnO nanowires doped with Mg have been successfully prepared on Au-coated Si (111) substrates using chemical vapor deposition method with a mixture of ZnO, Mg, and activated carbon powders as reactants at 850°C. The structural, compositional, morphological and optical properties of the samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscopy, and photoluminescence spectroscopy. The nanowires are single crystalline in nature and preferentially grow up along [0001] direction with the average diameter and length of about 60 nm and several hundred micrometers, respectively, thinner and longer than the results of literature using the similar method. Room temperature photoluminescence spectroscopy shows a blueshift from the bulk band gap emission, which can be attributed to Mg doping that were detected by energy dispersive X-ray analysis EDX in the nanowires. Finally, the possible growth mechanism of crystalline ZnO nanowires is discussed briefly.
Źródło:
Acta Physica Polonica A; 2011, 119, 6; 819-823
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Parameter calibration for the discrete element simulation model of commercial organic fertilizer
Autorzy:
Xie, C.
Yang, J.
Wang, B.
Zhuo, P.
Li, C.
Wang, L.
Powiązania:
https://bibliotekanauki.pl/articles/2082983.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
commercial organic fertilizer
discrete element
repose angle
parameter calibration
parameters for the particle
model
Opis:
The parameters of a discrete element simulation model for commercial organic fertilizer particles were obtained both quickly and accurately, so that the uniformity and stability of the fertilizer discharged from the feeder may be studied using the discrete element simulation method. This study screened out the parameters which significantly influenced the repose angle of the commercial organic fertilizer using the Plackett-Burman test. Then, a model for the quadratic regression response surface of the repose angle vs the parameters was established through a Box-Behnken experiment with the measured repose angle of the fertilizer particles as the optimization index. The optimization results showed that the rolling friction coefficient and static friction coefficient between the fertilizer particles, as well as the optimal simulation parameter for the Johnson-Kendall-Roberts surface energy were 0.056, 0.355 and 0.011 J m-2, respectively. A discrete element simulation test was carried out with the optimal simulation parameters, and the repose angle error of the simulation test was found to be 0.40% relative to that of the physical test, which proved the accuracy and validity of the simulation parameters for the discrete element model of the organic fertilizer. The simulation results may provide the basic parameters for establishing a discrete element model of commercial organic fertilizer particles and investigating the performance of organic fertilizer feeders using the simulation method.
Źródło:
International Agrophysics; 2021, 35, 1; 107-117
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Seismic damage behaviour of aeolian sand reinforced concrete columns with I-shaped structural steel
Autorzy:
Wang, Y. H.
Wang, H. Y.
Wang, Y. P.
Zhao, M.
Qi, J.
Huo, G. Z.
Liu, P. Q.
Powiązania:
https://bibliotekanauki.pl/articles/1849772.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
piasek eoliczny
słup żelbetowy
stal konstrukcyjna
przekrój I
zachowanie
uszkodzenie sejsmiczne
model uszkodzenia
aeolian sand
column
I-shaped steel
structural steel
seismic damage
behaviour
damage model
Opis:
To promote the application of aeolian sand resources for steel-concrete composite structures, an aeolian sand reinforced concrete column with I-shaped structural steel is proposed in this study. Four specimens are designed and manufactured with different replacement rates of aeolian sand. The seismic behaviour and damage evolution process of the specimens are studied by low-cycle repeated loading tests. Based on the test results, the mechanical characteristics, failure modes, hysteresis curves, skeleton curves, energy dissipation capacity, displacement ductility, and stiffness degradation of the specimens with different replacement rates of aeolian sand are analysed. In addition, the effects of the design parameters on the seismic behaviour of the specimens are also studied. The results show that the indexes of the seismic behaviour can be significantly improved by adding steel. Moreover, a revised damage model is proposed, to better reflect the evolution law of seismic damage of aeolian sand reinforced concrete columns with steel. The proposed model can provide an important reference for seismic damage assessment of the columns.
Źródło:
Archives of Civil Engineering; 2020, 66, 4; 633-650
1230-2945
Pojawia się w:
Archives of Civil Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A polarization filter at 1550 nm based on photonic crystal fiber with symmetry around gold-coated holes
Autorzy:
Zha, F.
Li, J.
Sun, P.
Wang, X.
Powiązania:
https://bibliotekanauki.pl/articles/173897.pdf
Data publikacji:
2018
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
photonic crystal fiber
polarization filter
finite element method
surface plasmon resonance
Opis:
A polarization photonic crystal fiber based on surface plasmon resonance is proposed in this paper. The photonic crystal fiber with gold coated holes is studied through using the finite element method. The impacts of structural parameters on the resonance characteristics are discussed. Numerical simulations show that the resonance wavelength can be modulated by changing the parameters of the air holes and thickness of gold layer. At the resonance wavelength 1550 nm, the loss is 3.8045 dB/m in x-polarization and the loss is 28464 dB/m in y-polarization by adjusting the size of the gold-coated holes and the place of air holes. Results show that the loss of y-polarized mode is much larger than the loss of x-polarized mode. The y-polarized mode is suppressed, and only x-polarized mode can be guided at the resonance wavelength of y-polarized mode. The results indicate that the mode polarized in one direction can be filtered out selectively by adjusting the diameter of air holes, and the filtering effect in a communication band is achieved.
Źródło:
Optica Applicata; 2018, 48, 4; 609-620
0078-5466
1899-7015
Pojawia się w:
Optica Applicata
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High Pressure Far-Infrared Magnetooptical Studies of Sn and S Donors in GaAs
Autorzy:
Dmochowski, J. E.
Wang, P. D.
Stradling, R. A.
Powiązania:
https://bibliotekanauki.pl/articles/1888152.pdf
Data publikacji:
1991-08
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
71.55.Eq
78.50.Ge
Opis:
The diamond anvil cell technique is applied for magneto-optical far-infrared transmission experiments with LPE grown GaAs:Sn. The 1s-2p(+) intra-shallow-Γ-donor transition is investigated as a function of high hydrostatic pressure for Sn and residual S donors. Both donors are shallow up to 30 kbar. Above this pressure both donors become deep and shallow donor absorption is persistently bleached due to deep non-metastable (non DX-like) states of the donors entering the gap of GaAs.
Źródło:
Acta Physica Polonica A; 1991, 80, 2; 279-282
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of field tension infiltrometer data by parameter estimation
Autorzy:
Simunek, J.
Wang, Dong
Shouse, P.J.
Van Genuchten, M.T.
Powiązania:
https://bibliotekanauki.pl/articles/26040.pdf
Data publikacji:
1998
Wydawca:
Polska Akademia Nauk. Instytut Agrofizyki PAN
Tematy:
field tension
Wooding's analysis
tension disc infiltrometer
hydraulic property
soil property
parameter estimation
Źródło:
International Agrophysics; 1998, 12, 3
0236-8722
Pojawia się w:
International Agrophysics
Dostawca treści:
Biblioteka Nauki
Artykuł
Wyświetlanie 1-15 z 54

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies