Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "equivalent temperature" wg kryterium: Temat


Wyświetlanie 1-10 z 10
Tytuł:
Zróżnicowanie temperatury ekwiwalentnej w Lublinie w latach 2009–2010
Autorzy:
Dobek, Mateusz
Powiązania:
https://bibliotekanauki.pl/articles/763198.pdf
Data publikacji:
2013
Wydawca:
Uniwersytet Marii Curie-Skłodowskiej. Wydawnictwo Uniwersytetu Marii Curie-Skłodowskiej
Tematy:
biothermal conditions
equivalent temperature
Lublin
Opis:
In 2009–2010, in five points in Lublin, located in areas of different land use and built-up, measurements of air temperature and humidity were taken. Based on the data collected, the following elements were calculated: the difference in average monthly air temperature between the coldest point and the others, equivalent temperature (Tek) and Tek thermal sensations. Differencesin average monthly air temperature in relation to the outskirts of Lublin were the highest at the point Dominikanie, in the built-up area of the old town. Most frequently “sultry” sensation was reported for the estate houses, at the point Ofelii. Different biothermal conditions were observed in the center of the city – Litewski square. It is characterized by a high proportion of vegetation. Green areas influenced the reduction of the biothermal stress compared to other points. The highest frequency of thermal sensation “cold”, “cool” and “slightly cool” were recorded there. Measurements points located in two housing estates with high buildings close to each other were characterized by similar biothermal conditions. In these areas, comparing to other discussed areas of the city, at 12 UTC relatively often there were noticed the best biothermal conditions – “comfortable” according to equivalent temperature index.
Artykuł nie zawiera abstraktu w języku polskim
Źródło:
Annales Universitatis Mariae Curie-Sklodowska, sectio B – Geographia, Geologia, Mineralogia et Petrographia; 2013, 68, 2
0137-1983
Pojawia się w:
Annales Universitatis Mariae Curie-Sklodowska, sectio B – Geographia, Geologia, Mineralogia et Petrographia
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Temperatura ekwiwalentna i operatywna w ocenie środowiska wnętrz
Equivalent and operative temperature in the assessment of interior environment
Autorzy:
Lis, A.
Powiązania:
https://bibliotekanauki.pl/articles/2068351.pdf
Data publikacji:
2015
Wydawca:
Politechnika Częstochowska
Tematy:
temperatura ekwiwalentna
temperatura operatywna
komfort cieplny
budynek edukacyjny
equivalent temperature
operative temperature
thermal comfort
educational building
Opis:
W artykule przedstawiono wyniki analizy temperatury ekwiwalentnej i operatywnej, które są wskaźnikami komfortu cieplnego ludzi w pomieszczeniach. Analizę przeprowadzono w grupie budynków edukacyjnych. Pomiarów wskaźników dokonano przy użyciu miernika komfortu cieplnego. Pomierzono podstawowe termiczne elementy mikroklimatu wnętrz. Prześledzono zmiany wartości temperatury ekwiwalentnej i operatywnej związane ze zmianami wartości elementów mikroklimatu.
The paper presents the results of the research of equivalent and operative temperature which are the indicators of human thermal comfort in rooms. The analysis was made in educational buildings. Measurements of these indicators were made using the thermal comfort meter. Basic thermal parameters of microclimate were measured. There were investigated changes in the equivalent and operative temperature associated with changes of microclimate parameters.
Źródło:
Zeszyty Naukowe Politechniki Częstochowskiej. Budownictwo; 2015, 21 (171); 183--189
0860-7214
Pojawia się w:
Zeszyty Naukowe Politechniki Częstochowskiej. Budownictwo
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design and performance of dual-band MWIR/LWIR focal plane arrays based on a type-II superlattice nBn structure
Autorzy:
Lee, Hyun-Jin
Eom, Jun Ho
Jung, Hyun Chul
Kang, Ko-Ku
Ryu, Seong Min
Jang, Ahreum
Kim, Jong Gi
Kim, Young Ho
Jung, Han
Kim, Sun Ho
Choi, Jong Hwa
Powiązania:
https://bibliotekanauki.pl/articles/2204217.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Stowarzyszenie Elektryków Polskich
Tematy:
InAs/GaSb type-II superlattice
dualband detector
dark current
spectral quantum efficiency
noise equivalent temperature difference
Opis:
Dual-band infrared detector, which acquires more image information than single-band detectors, has excellent detection, recognition, and identification capabilities. The dual-band detector can have two bumps to connect with each absorber layer, but it is difficult to implement small pitch focal plane arrays and its fabrication process is complicated. Therefore, the most effective way for a dual-band detector is to acquire each band by biasselectable with one bump. To aim this, a dual-band MWIR/LWIR detector based on an InAs/GaSb type-II superlattice nBn structure was designed and its performance was evaluated in this work. Since two absorber layers were separated by the barrier layer, each band can be detected by bias-selectable with one bump. The fabricated dual-band device exhibited the dark current and spectral response characteristics of MWIR and LWIR bands under negative and positive bias, respectively. Spectral crosstalk that is a major issue in dualband detectors was also improved. Finally, a 20 µm pitch 640 x 512 dual-band detector was fabricated, and both MWIR and LWIR images exhibited an average noise equivalent temperature difference of 30 mK or less at 80 K.
Źródło:
Opto-Electronics Review; 2023, 31, Special Issue; art. no. e144560
1230-3402
Pojawia się w:
Opto-Electronics Review
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zarys bioklimatu Zamościa
The Bioclimate of Zamość
Autorzy:
Samborski, Andrzej
Powiązania:
https://bibliotekanauki.pl/articles/26850527.pdf
Data publikacji:
2023
Wydawca:
Akademia Zamojska
Tematy:
temperatura powietrza
wilgotność względna
prędkość wiatru
suma opadów atmosferycznych
wskaźnik wielkości ochładzającej
temperatura ekwiwalentna
temperatura efektywna
air temperature
relative humidity
wind speed
precipitation
cooling magnitude indicator
equivalent temperature
effective temperature
Opis:
W pracy wykorzystano dane ze stacji meteorologicznych funkcjonujących na terenie Zamościa w okresie od 1976 do 2020 roku. Opisano zmienność wartości wybranych elementów meteorologicznych i charakterystyk klimatycznych w skali czasowej, wykorzystując najczęściej stosowane statystyki rozkładu, tzn. wartości średnie oraz miary zmienności. Wyznaczono kierunek trendu zmian temperatury powietrza. W celu określenia warunków bioklimatycznych obliczono wartości wybranych wskaźników, takich jak: temperatura ekwiwalentna, temperatura efektywna i wielkość ochładzająca powietrza. Przeprowadzone badania wskazują, że w Zamościu optymalne warunki termiczne określane jako przyjemnie chłodno występują w okresie letnim (czerwiec, lipiec, sierpień), przy czym w lipcu są one łagodne. W kwietniu, maju i we wrześniu odczucie cieplne charakteryzowane jest jako chłodne. Generalnie w okresie od listopada do marca jest zimno, a w styczniu i w lutym bardzo zimno.
The paper uses data from meteorological stations operating in Zamość in the period from 1976 to 2020. The variability of the values of selected meteorological elements and climatic characteristics on a time scale was presented using the most commonly used distribution statistics, i.e. average values and variability measures. The direction of the trend of changes in air temperature was determined as well. In order to determine the bioclimatic conditions, the values of selected indicators were calculated, including equivalent temperature, effective temperature, and air cooling quantity. The conducted research indicates that in Zamość optimal thermal conditions described as pleasantly cool occur in the summer ( June, July, August), while in July they are mild. In April, May and September, the thermal sensation is characterized as cool. Generally, it is cold from November to March and very cold in January and February.
Źródło:
Facta Simonidis; 2023, 16, 1; 341-356
1899-3109
Pojawia się w:
Facta Simonidis
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A generalized equivalent temperature model in a time-varying environment
Uogólniony model temperatury równoważnej w zmiennym w czasie otoczeniu
Autorzy:
Sun, L.
Gu, X.-H.
Song, P.
Di, Y.
Powiązania:
https://bibliotekanauki.pl/articles/301556.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
przyspieszone badania starzenia
temperatura równoważna
przechowywanie w warunkach naturalnych
krzywa degradacji
oringi nitrylowe
accelerated degradation test
equivalent temperature
nature storage
degradation path
rubber Orings
Opis:
Accelerated degradation test at high temperature level is a common method to accelerate the degradation of products by elevating temperature, and the obtained degradation data are then used to obtain the estimate of the performance at normal temperature after extrapolating the degradation through accelerating model. However, the normal temperature is ever-changing rather than constant. Therefore, a generalized equivalent temperature model based on power law degradation path is proposed to establish a connection between accelerated degradation data and degradation data at normal temperature. The model takes the equal degradation measure as a principle and the conclusion is demonstrated that the increments of the degradation under the same magnitude, same time and different orders of temperature stresses are same. The result shows that the empirical equivalent temperature model is a special case of the proposed model. The accuracy of the proposed model is finally demonstrated by a case study of nitrile rubber O-rings.
Przyspieszone badania degradacji (badania starzeniowe) prowadzone w warunkach wysokiej temperatury stanowią powszechnie stosowaną metodę przyspieszania starzenia produktów poprzez podwyższanie temperatury. Otrzymane w takich badaniach dane degradacyjne wykorzystuje się do szacowania wydajności produktu w temperaturze normalnej na zasadzie ekstrapolacji. Głównym ograniczeniem tej metody jest fakt, że normalna temperatura nie jest stała lecz zmienia się w czasie. Dlatego też, aby skorelować dane z przyspieszonej degradacji z danymi dotyczącymi starzenia w normalnej temperaturze, zaproponowaliśmy uogólniony model temperatury równoważnej oparty na krzywej degradacji opisanej prawem potęgowym. W modelu przyjęto zasadę równego stopnia degradacji i wykazano, że przyrosty degradacji przy tej samej wartości i czasie działania naprężeń termicznych różnego rzędu są takie same. Wyniki pokazują, że empiryczny model temperatury równoważnej jest szczególnym przypadkiem proponowanego przez nas modelu. Trafność opisanego w pracy modelu wykazano na podstawie studium przypadku dotyczącego uszczelek nitrylowych, tzw. oringów.
Źródło:
Eksploatacja i Niezawodność; 2017, 19, 3; 432-440
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Long wavelength type-II superlattice barrier infrared detector for CubeSat hyperspectral thermal imager
Autorzy:
Rafol, Sir B.
Gunapala, Sarath D.
Ting, David Z.
Soibel, Alexander
Khoshakhlagh, Arezou
Keo, Sam A.
Pepper, Brian J.
Hill, Cory J.
Maruyama, Yuki
Fisher, Anita M.
Sood, Ashok
Zeller, John
Wright, Robert
Lucey, Paul
Nunes, Miguel
Flynn, Luke
Babu, Sachidananda
Ghuman, Parminder
Powiązania:
https://bibliotekanauki.pl/articles/2204204.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Stowarzyszenie Elektryków Polskich
Tematy:
type-II superlattice
focal plane array
infrared detector
quantum efficiency
noise equivalent difference temperature
dark current density
anti-reflective coating
Opis:
The hyperspectral thermal imaging instrument for technology demonstration funded by NASA’s Earth Science Technology Office under the In-Space Validation of Earth Science Technologies program requires focal plane array with reasonably good performance at a low cost. The instrument is designed to fit in a 6U CubeSat platform for a low-Earth orbit. It will collect data on hydrological parameters and Earth surface temperature for agricultural remote sensing. The long wavelength infrared type-II strain layer superlattices barrier infrared detector focal plane array is chosen for this mission. With the driving requirement dictated by the power consumption of the cryocooler and signal-noise-ratio, cut-off wavelengths and dark current are utilized to model instrument operating temperature. Many focal plane arrays are fabricated and characterised, and the best performing focal plane array that fulfils the requirements is selected. The spectral band, dark current and 8-9.4 μm pass band quantum efficiency of the candidate focal plane array are: 8-10.7 μm, 2.1∙10ˉ⁵ A/cm², and 47%, respectively. The corresponding noise equivalent difference temperature and operability are 30 mK and 99.7%, respectively. Anti-reflective coating is deposited on the focal plane array surface to enhance the quantum efficiency and to reduce the interference pattern due to an absorption layer parallel surfaces cladding material.
Źródło:
Opto-Electronics Review; 2023, 31, Special Issue; art. no. e144569
1230-3402
Pojawia się w:
Opto-Electronics Review
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Equivalent climate temperature analysis as a criterion of climate hazard evaluation in Polish underground mines
Analiza temperatury zastępczej klimatu jako kryterium oceny zagrożenia klimatycznego w polskich kopalniach podziemnych
Autorzy:
Głuch, B.
Powiązania:
https://bibliotekanauki.pl/articles/219054.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ocena warunków mikroklimatu
zagrożenie klimatyczne
kopalnie podziemne
temperatura zastępcza klimatu
model przewidywanego strumienia cieplnego
model PHS
evaluation of microclimate conditions
climate hazard
underground mines
equivalent climate temperature
predicted heat strain model
PHS model
Opis:
The article discusses changes in Polish regulations concerning assessment of the climate hazard in underground mines. Currently, the main empirical index representing the heat strain, used in qualification of the workplace to one of the climate hazard levels in Poland is the equivalent climate temperature. This simple heat index allows easy and quick assessment of the climate hazard. To a major extent, simple heat indices have simplifications and are developed for a specific working environments. Currently, the best methods used in evaluation of microclimate conditions in the workplace are those based on the theory of human thermal balance, where the physiological parameters characterising heat strain are body water loss and internal core temperature of the human body. The article describes the results of research on usage of equivalent climate temperature to heat strain evaluation in underground mining excavations. For this purpose, the numerical model of heat exchange between man and his environment was used, taken from PN-EN ISO 7933:2005. The research discussed in this paper has been carried out considering working conditions and clothing insulation in use in underground mines. The analyses performed in the study allowed formulation of conclusions concerning application of the equivalent climate temperature as a criterion of assessment of climate hazards in underground mines.
W artykule omówiono zmiany w polskich przepisach dotyczących oceny zagrożenia klimatycznego w kopalniach podziemnych. Obecnie głównym wskaźnikiem zaliczenia stanowiska pracy do jednego ze stopni zagrożenia klimatycznego jest temperatura zastępcza klimatu. Ten prosty wskaźnik mikroklimatu umożliwia wykonanie, w łatwy i szybki sposób, oceny zagrożenia klimatycznego. Proste wskaźniki mikroklimatu w dużej mierze posiadają uproszczenia i są opracowane do konkretnego środowiska pracy. Najlepszymi obecnie metodami oceny warunków cieplnych pracy są metody oparte na teorii bilansu cieplnego człowieka, gdzie parametrami fizjologicznymi charakteryzującymi obciążenie cieplne jest ubytek wody z organizmu oraz temperatura wewnętrzna ciała. W artykule opisano wyniki badań nad zasadnością zastosowania temperatury zastępczej klimatu do oceny obciążenia cieplnego w wyrobiskach podziemnych. W tym celu wykorzystano model numeryczny wymiany ciepła między organizmem człowieka a otoczeniem, zaczerpnięty z normy PN-EN ISO 7933:2005. Omawiane badania zostały przeprowadzone przy uwzględnieniu ciężkości pracy oraz izolacyjności termicznej odzieży stosowanej w zakładach górniczych. Zrealizowane badania pozwoliły na sformułowanie wniosków dotyczących zastosowania temperatury zastępczej klimatu jako kryterium oceny zagrożenia klimatycznego w kopalniach podziemnych.
Źródło:
Archives of Mining Sciences; 2018, 63, 4; 975-988
0860-7001
Pojawia się w:
Archives of Mining Sciences
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Importance of snow as component of surface mass balance of Arctic glacier (Hansbreen, southern Spitsbergen)
Autorzy:
Uszczyk, Aleksander
Grabiec, Mariusz
Laska, Michał
Kuhn, Michael
Ignatiuk, Dariusz
Powiązania:
https://bibliotekanauki.pl/articles/2041844.pdf
Data publikacji:
2019
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Arctic
Svalbard
snowpack
snow accumulation and ablation
snow water equivalent
temperature index model
Źródło:
Polish Polar Research; 2019, 40, 4; 311-338
0138-0338
2081-8262
Pojawia się w:
Polish Polar Research
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wykorzystanie ekwiwalentnej stałej czasowej w pomiarach szybkozmiennych temperatur w regeneratorze zintegrowanym z palnikiem gazowym
Use of equivalent time-constant for measurement of rapidly changing temperatures in the regenerator integrated with gas burner
Autorzy:
Wnęk, M.
Powiązania:
https://bibliotekanauki.pl/articles/151941.pdf
Data publikacji:
2012
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
pomiar szybkozmiennej temperatury
czujniki termometryczne
regenerator
ekwiwalentna stała czasowa
palnik gazowy
rapidly changing temperature measurement
thermometric sensors
equivalent time-constant
gas burner
Opis:
Przedstawiono wyniki badań modelowania matematycznego dynamiki termoelektrycznych czujników płaszczowych. Omówiono wpływ parametrów konstrukcyjnych termoelementu na pomiar temperatury oraz dogodny model - łatwy do wykorzystania podczas pomiaru szybkozmiennej temperatury czynnika w celu korekty dynamicznego błędu przetwarzania. Zaprezentowano wykorzystanie ekwiwalentnej stałej czasowej przy doborze średnicy czujnika termoelektrycznego do pomiaru szybkozmiennej temperatury.
Temperature is the one of the most important parameters which has to be controlled in industrial processes because of technology. The measurement problem of rapidly changing temperature of hot and cold fluids flowing alternately through the regenerator at short intervals is presented in the paper. The metallurgical, high temperature heating furnace with regenerative burners [1, 2, 4, 5, 6, 7] has been used as an example of the measurement problem appearance (Fig. 1). Periodicity of the system operation (Fig. 2) characterized by the interval shorter than 30 s is quite significant due to the dynamical converting error of sensors. The measurement and mathematical modelling results of dynamics of thermoelectric sensors are presented (Fig. 3). The influence of thermocouple construction parameters on temperature measurement is discussed. A convenient model for correcting the error of dynamic processing is described. This model is easy to use for rapidly changing medium temperature. The method presented for approximation of dynamic properties of thermometric sensors by inertia of the first order with the equivalent time-constant ?E is of great practical importance (Fig. 5). This method provides an easy way to assess the impact of construction and thermophysical parameters of the sensor materials and the heat transfer coefficient, from fluid to a thermocouple, on the thermocouple dynamic prop-erties. The use of the equivalent time-constant during the thermocouple diameter selection for measurement of rapidly changing temperature is presented. When minimizing the error of dynamic sensor processing.
Źródło:
Pomiary Automatyka Kontrola; 2012, R. 58, nr 5, 5; 435-438
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Vliania konstruktivnyh elementov ustrojstv na dispersnost kapel vody dla osaždeniâ produktov gorenia i sniżenia temperatury v obemah pomescenij vo vrema pożara
Investigation of the influence of structural elements devices on dispersed water droplets to precipitate the product of combustion and reduce the tempeature in the volume of the room during a firer
Wpływ elementów konstrukcyjnych urządzeń do wytwarzania rozproszonych strumieni wody na zmniejszenie produktów spalania i redukcje temperatury podczas pożaru
Autorzy:
Luŝ, V.
Loik, V.
Štangret, N.
Matuškevič, R.
Powiązania:
https://bibliotekanauki.pl/articles/136452.pdf
Data publikacji:
2017
Wydawca:
Szkoła Główna Służby Pożarniczej
Tematy:
hazardous fire factors
smoke and combustion products
temperature decrease
combustion products precipitation
water droplet dispersion
visibility increase
classification of water spraying methods
pneumo-hydraulic spraying
centrifugal nozzles
equivalent droplet diameter
produkty spalania
spadek temperatury
redukcja produktów spalania
dyspersja kropel wody
zwiększenie widoczności
klasyfikacja metod rozpylenia wody
rozpylanie pneumo-hydrauliczne
dysze odśrodkowe
równoważna średnica kropelek
Opis:
В статье рассмотрены устройства для осаждения продуктов горения, снижение температуры в объеме помещения и увеличение видимости. Основное внимание уделялось выбору способа распыления воды на мелкодисперсные частицы, влияния скорости потока воздуха на дисперсность капель, которые выходят из центробежной форсунки. Целью исследования является развитие метода расчета одного из главных параметров модели – эквивалентного диаметра капель струи распыленной воды. Ранее определение этого параметра было возможно лишь с помощью сложных экспериментальных измерений. В данной работе для его расчета применены ранее опубликованные литературные данные. Формула, полученная в работе, позволяет выполнять расчет эквивалентного диаметра капель на основе конструктивных параметров. Графические зависимости, полученные с помощью формулы, позволили определить зависимость эквивалентного диаметра капель от технических параметров. Применение формулы к математической модели теплозащиты позволило расширить ее возможности для практического применения. Также предлагается методика расчёта теплопоглощения порции воды в зависимости от диаметра монодиспергированых водяных капель и влияние дисперсности на интенсивность подачи воды для обеспечения тушения очага пожара.
In the article, are considered devices for depositing combustion products, reducing the temperature in the room volume and increasing visibility. The main attention was paid to the choice of the method for atomizing water into fine particles, the effect of air flow velocity on the dispersion of droplets that leave the centrifugal nozzle. The purpose of the study is to develop a method for calculating one of the main parameters of the model – the equivalent diameter of the droplets of a spray of water. Earlier, the definition of this parameter was possible only with the help of complex experimental measurements. In this paper, previously published literature data are used to calculate it. The formula obtained in the work makes it possible to calculate the equivalent droplet diameter on the basis of design parameters. Graphic dependencies obtained with the help of the formula made it possible to determine the dependence of the equivalent droplet diameter on technical parameters. Application of the formula to the mathematical model of heat protection has allowed expanding its possibilities for practical application. Also, a method is proposed for calculating the heat absorption of a portion of water as a function of the diameter of monodispersed water droplets and the effect of dispersion on the intensity of the water supply in order to extinguish the fire.
W artykule opisano wpływ dysz wodnych na redukcje produktów spalania, obniżenie temperatury w pomieszczeniu, a także poprawę widoczność w pożarze. Główną uwagę zwrócono na wybór metody rozpylania wody na drobne cząstki oraz wpływ prędkości przepływu powietrza na dyspersję kropel powstających w dyszach. Celem badania było opracowanie metody obliczania jednego z głównych parametrów modelu – równoważnej średnicy kropel rozpylanej wody. Dotychczas definicja tego parametru była możliwa do określenia tylko przy pomocy złożonych pomiarów doświadczalnych. W niniejszym artykule do określenia pożądanego parametru wykorzystano dane literaturowe. Wzór uzyskany w pracy pozwala obliczyć równoważną średnicę kropel na podstawie parametrów projektowych. Krzywe uzyskane przy pomocy wzoru określają zależność średnicy kropel względem parametrów technicznych urządzeń. W artykule proponuje się ponadto metodę obliczania absorpcji ciepła w zależności od średnicy kropel oraz wpływu dyspersji na intensywność podawania wody w trakcie pożaru.
Źródło:
Zeszyty Naukowe SGSP / Szkoła Główna Służby Pożarniczej; 2017, 4, 64; 125-149
0239-5223
Pojawia się w:
Zeszyty Naukowe SGSP / Szkoła Główna Służby Pożarniczej
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-10 z 10

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies