Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Xu, M." wg kryterium: Autor


Wyświetlanie 1-3 z 3
Tytuł:
Automatic calibration system for digital-display vibrometers based on machine vision
Autorzy:
He, W.
Xu, G.
Rong, Z.
Li, G.
Liu, M.
Powiązania:
https://bibliotekanauki.pl/articles/221163.pdf
Data publikacji:
2014
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
image recognition
calibration
vibration measurement
machine vision
automatic testing
digital-display vibrometer
Opis:
Considering the low efficiency during the process of traditional calibration for digital-display vibrometers, an automatic calibration system for vibrometers based on machine vision is developed. First, an automatic vibration control system is established on the basis of a personal computer, and the output of a vibration exciter on which a digital-display vibrometer to be calibrated is installed, is automatically adjusted to vibrate at a preset vibration level and a preset frequency. Then the display of the vibrometer is captured by a digital camera and identified by means of image recognition. According to the vibration level of the exciter measured by a laser interferometer and the recognized display of the vibrometer, the properties of the vibrometer are calculated and output by the computer. Image recognition algorithms for the display of the vibrometer with a high recognition rate are presented, and the recognition for vibrating digits and alternating digits is especially analyzed in detail. Experimental results on the built-up system show that the prposed image recognition methods are very effective and the system could liberate operators from boring and intense calibration work for digital-display vibrometers.
Źródło:
Metrology and Measurement Systems; 2014, 21, 2; 317-328
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Combined Influence of Silicon Content and Oxygen Concentration on the Oxidation Process of Silicon-Containing Steels
Autorzy:
Yuan, Q.
Xu, G.
Zhou, M.
He, B.
Hu, H.
Powiązania:
https://bibliotekanauki.pl/articles/352126.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
silicone content
oxygen concentration
mass gain
isothermal holding time
Opis:
The combined influence of silicon content and oxygen concentration on silicon-containing steels was investigated, via a heating route similar to that applied in the industrial reheating process, using a Simultaneous Thermal Analyzer (STA). Four different oxygen concentrations and three different isothermal holding times were designed. The results show that the effect of silicon on the mass gain depends on the oxygen concentration and the oxidation time. The mass gain of low-silicon steel is greater than that of high-silicon steel at 1260°C in the oxygen concentrations of 1.0 vol.% and 2.0 vol.%, even when the isothermal holding time is 90 minutes. However, there is a critical time point for mass gain in oxygen concentrations ≥3.0 vol.%. The mass gain of lowsilicon steel is greater before and smaller after this critical point. The critical time is deferred with decreasing oxygen concentration.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 445-450
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Strain Rate on the Microstructure of Warm-Deformed Ultrafined Medium-Carbon Steel
Autorzy:
Yuan, Q.
Xu, G.
Liu, S.
Liu, M.
Hu, H.
Powiązania:
https://bibliotekanauki.pl/articles/355659.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
warm deformation
medium-carbon steel
ultrafine grain
strain rate
Fe3C
Opis:
In this study, medium-carbon steel was subjected to warm deformation experiments on a Gleeble 3500 thermosimulator machine at temperatures of 550°C and 650°C and strain rates of 0.001 s-1 to 1 s-1. The warm deformation behavior of martensite and the effects of strain rate on the microstructure of ultrafine grained medium-carbon steel were investigated. The precipitation behavior of Fe3C during deformation was analyzed and the results showed that recrystallization occurred at a low strain rate. The average ultrafine ferrite grains of 500 ± 58 nm were fabricated at 550°C and a strain rate of 0.001 s-1. In addition, the size of Fe3C particles in the ferrite grains did not show any apparent change, while that of the Fe3C particles at the grain boundaries was mainly affected by the deformation temperature. The size of Fe3C particles increased with the increasing deformation temperature, while the strain rate had no significant effect on Fe3C particles. Moreover, the grain size of recrystallized ferrite decreased with an increase in the strain rate. The effects of the strain rate on the grain size of recrystallized ferrite depended on the deformation temperature and the strain rate had a prominent effect on the grain size at 550°C deformation temperature. Finally, the deformation resistance apparently decreased at 550°C and strain rate of 1 s-1 due to the maximum adiabatic heating in the material.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 4; 1805-1813
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies