Autor: Lee, C. H. - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Synthesis, Structure, Photoluminescence, and Raman Spectrum of Indium Oxide Nanowires
Autorzy:: Kim, H.
Na, H.
Yang, J.
Lee,, C.
Powiązania:: https://bibliotekanauki.pl/articles/1505485.pdf
Data publikacji:: 2011-02
Wydawca:: Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:: 81.07.-b
78.55.-m
Opis:: Production of indium oxide $(In_2O_3)$ whiskers at a very low temperature of 650°C was reported. The synthetic route was comprised of a thermal heating process of a mixture of In and Mg powders. We have investigated the structural properties of the as-synthesized nanowires by using X-ray diffraction and scanning electron microscopy. The product consisted of one-dimensional nanowires, with a crystalline cubic structure of $In_2O_3$. The photoluminescence measurement with the Gaussian fitting exhibited visible light emission bands centered at 2.1 eV and 2.8 eV. The peaks of the Raman spectrum were indexed to the modes being associated with cubic $In_2O_3$.
Źródło:: Acta Physica Polonica A; 2011, 119, 2; 143-145
0587-4246
1898-794X
Pojawia się w:: Acta Physica Polonica A
Dostawca treści:: Biblioteka Nauki

Artykuł

Skocz do pozycji: 2.

Tytuł:: A study on the development of a new grinding processes for high-lead ball screw nuts
Autorzy:: Choi, Ch.
Ha, Y.
Kim, H.
Lee, C.
Powiązania:: https://bibliotekanauki.pl/articles/99599.pdf
Data publikacji:: 2010
Wydawca:: Wrocławska Rada Federacji Stowarzyszeń Naukowo-Technicznych
Tematy:: high-lead ball screw nuts
new grinding process
surface roughness
Opis:: This paper proposes a method that machines the race of high-lead ball screw nuts, which is difficult to machine using the existing geometrical machining method, without any interferences and changes in its load rating in order to perform the high-speed in ball screws. This study calculates the inclination angle of the axis of the grinding stone for avoiding the contact of the axis to the inner diamete of the nut and determines the shape of the grinding stone through changing the inclination angle and dressing curvature determined in a dressing device Then, the grinding condition will be determined by measuring the shape meter of the screw race for solving the problem. Also, the surface roughness of the grinded surface was measured using a surface roughness tester, and check with applying a grinding process of product not being high-lead ball screw.
Źródło:: Journal of Machine Engineering; 2010, 10, 1; 50-57
1895-7595
2391-8071
Pojawia się w:: Journal of Machine Engineering
Dostawca treści:: Biblioteka Nauki

Artykuł

Skocz do pozycji: 3.

Tytuł:: Photoluminescence Studies of Aluminum Nitride Nanowires
Autorzy:: Yang, J.
Na, H.
Kim, H.
Kebede, M.
Choi, R.
Jeong, J.
Lee, C.
Powiązania:: https://bibliotekanauki.pl/articles/1505466.pdf
Data publikacji:: 2011-02
Wydawca:: Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:: 81.07.-b
78.55.-m
Opis:: We report the production of AlN nanowires by the thermal heating method, for exploring their photoluminescence properties. The room-temperature photoluminescence properties were investigated with different annealing environment. While broad emissions with peaks at around 2.45 and 2.95 eV were obtained from both unannealed and annealed samples, the additional 2.1 eV peak was found from the annealed samples. We have suggested the possible emission mechanisms based on the assumption that both 2.45 eV peak and 2.1 eV peak are ascribed to the nitrogen vacancies. Annealing in N_2 environment exhibited lower intensities of 2.45 eV peak and 2.1 eV peak in comparison to those in Ar environment, presumably due to the suppression of nitrogen vacancies.
Źródło:: Acta Physica Polonica A; 2011, 119, 2; 125-127
0587-4246
1898-794X
Pojawia się w:: Acta Physica Polonica A
Dostawca treści:: Biblioteka Nauki

Artykuł

Informacja