Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "internal combustion" wg kryterium: Temat


Wyświetlanie 1-7 z 7
Tytuł:
Microemulsion as a means of NOx reduction in exhaust emission of diesel engines
Autorzy:
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/247510.pdf
Data publikacji:
2016
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engines
engine emissions
internal combustion engine fuels
microemulsions
Opis:
Currently produced internal combustion engines used in transportation, must meet very stringent legislative requirements EURO VI, for the limited emissions of exhaust gases: CO, HC, NOx, PM, PN. One of the most toxic components and the most difficult to eliminate are nitrogen oxides NOx, which currently permissible amount in the exhaust gases shall be 80 mg/km. This result must be achieved, moreover, with the fulfilment of the limits for other exhaust components, and above all, the contents of particulate matter (PM, PN). It should be pointed out, that the mechanisms of the NOx and PM formation are opposed to each other; reduction of the NOx amount is generally associated with an increase in PM and vice versa. Therefore, issues of lowering the amount of NOx in the exhaust gases devote a lot of scientific work and engine research. Currently the most effective method of reducing the NOx is the selective catalytic reduction (SCR), which requires the additional installation of sophisticated equipment in the vehicle. Therefore, methods easier to implement and to operate are sought. One such method is the use of a microemulsion to supply as fuel to diesel engines, consisting of an emulsion of diesel oil, water and surfactant (surface-active compound). The use of the microemulsion results in that already in combustion chamber forms less of NOx, and therefore reduction of NOx in the exhaust system is easier. The publication presents results of SB 3.1 engine research on the engine test bench. The research was comparative in nature and thus, in the first stage of research conducted, the engine was fuelled with diesel oil, then the area of engine load and engine speed characteristics, in which the NOx emissions are greatest, was determined, and next, when engine was fuelled with various microemulsions, the engine investigation was conducted in this area. The microemulsions of diesel fuel and water comprise 10%, 20% and 30% water, selectively. The results of investigations show that, when the engine is fuelled with microemulsions, both NOx and PM, as the main component of diesel engine exhaust - soot (smoke) can be reduced at the same time. The article also discusses the differences between emulsions and microemulsions, and how they influence the combustion in the engine combustion chambers.
Źródło:
Journal of KONES; 2016, 23, 3; 225-232
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Heat release characteristics in combustion chamber of CI engine
Autorzy:
Jankowski, A.
Lagowski, P.
Slezak, M.
Powiązania:
https://bibliotekanauki.pl/articles/244001.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engines
diesel engines
combustion processes
heat release
Opis:
On the basis of the internal heat balance of CI engine with direct fuel injection, the quantity of heat transported during the combustion process from the combustion zone was determined. The real indicator diagrams are the bases for determination of the heat release Characteristics during the combustion process and making up of the internal heat balance. These diagrams were worked out for the engine fuelled with diesel oil for three sets of the injection timing and for work of the engine according to the full load engine Characteristics, and the load Characteristics taken at the engine speedb for the maximum engine torque. Tests with the three different injection timing were carried out. Tests with the load characteristics of the compression-igniting engine for five values of the power were carried out. The pressure in the cylinder of the engine during combustion process was recorded by means of liąuid cooled a piezo-electric quartz sensor with a load amplifier. Characteristics of heat release depended on the composition, temperature and the mol quantity of the working charge in the cylinder during the combustion process. Characteristics of the heat release were determined with the use of the novel calculation program. The program was worked out by authors at the assumption that the process of complete combustion was finished at the moment of the opening of the engine exhaust valve. For purpose of simplification calculation of the quantity of heat lost into the cooling system, the radiation, dissociation and incomplete combustion, were assumed to change during the combustion process in a linear way.
Źródło:
Journal of KONES; 2010, 17, 3; 155-164
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Heat transfer in combustion chamber of piston engines
Autorzy:
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/950137.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engines
heat transfer
heat flux
combustion chamber
heat losses
Opis:
Measurements were made during downward propagation of a flat flame in a lean limit methane/air mixture. It was observed that the limit flames are very thick and that heat losses to the walls caused extensive cooling of the product gases within 0.05 m behind the propagating flame. Analysis of all data from well synchronized measurements as well as the results of following to them numerical calculations made possible to understand in detail physical picture of heat transfer from the hot gases to the cold walls. It is a unique way for explanation of heat transfer phenomenon. Measurements and calculations were used to prepare heat balance in a flammability tube. In the next step measurements were carried out in a rotating cylindrical combustion chamber. This chamber was treated as a model of piston engine combustion chamber with swirl. Temperature changes on a surface of the rotating combustion chamber were transmitted towards motionless data acquisition system. The temperature measurements were carried out with the use of special thermocouples located at the front wall of the chamber. Influence of rotation velocity on heat transfer was investigated in the range from 1000rpm to 5000 rpm. For a constant mixture concentration maximum temperature rise depended on the rotation velocity. Increased rotation velocity initially intensified heat transfer to the wall, with following to it increase of peak temperature, but further rise of rotation velocity resulted in local flame extinction near the s idę walls, decreased volume of combustion gases, and as a result of these, decreased value of peak temperature at the wall surface. Presented techniques make possible estimate heat losses to the walls in a combustion chamber of piston engines.
Źródło:
Journal of KONES; 2010, 17, 1; 187-197
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design of novel composite pistons for diesel engine
Autorzy:
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/247362.pdf
Data publikacji:
2014
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engine
diesel engine
piston engine
composite alloy
combustion engine performance
Opis:
The paper presents the requirements to be met by diesel engines and their components, in particular pistons for engines of military vehicles. These requirements are related to the mass of modern military vehicles, which has greatly increased. Materials for the piston should have a good strength properties and low hysteresis of thermal expansion coefficient α across the range of operating temperatures, good resistance to galling, low abrasion, low coefficient of friction and good functional properties. On the clearance of the piston in the cylinder, the coefficient of thermal expansion α and its hysteresis has a decisive influence. The paper includes information on the piston working clearances, the requirements for pistons materials, their chemical composition, standard materials for the forged pistons, for the cast pistons (silumin alloys) and for the composite pistons. The paper presents the changes in coefficient of thermal expansion for the alloy in the raw state and after heat treatment and pistons made of new composite material prior to motor testing and after these tests. The completed new pistons have a lower coefficient of thermal expansion and lower hysteresis α, which allows reducing the running piston and cylinder clearances with the resulting effects.
Źródło:
Journal of KONES; 2014, 21, 4; 211-216
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Verification of the precise position of the aircraft in air navigation based on the solution of the RTK-OTF technique
Autorzy:
Kowalski, M.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/242780.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engine
Diesel engine
engine piston
composite alloy
thermal stability
Opis:
Certain results of the comparative studies of the high-speed Diesel engine V-12 of the “W” series were presented in the article. The engine was modernised in regard of possibilities to achieve better performances at specific fuel consumption, smaller exhaust emission, smaller scavenge, lower noise and better thermal stability. The subject of this work is the piston cast of novel composite silumin. The development of novel composite silumin (aluminium-silicon alloy), which contains a little more Copper and Nickel, and the introduction of novel alloyed elements, such as Chromium, Molybdenum, Tungsten, increases the strength of the alloy and its thermal stability during successive heating and cooling. The pistons made of this alloy may have a little bigger outside diameter than the pistons made of PA-12 standard alloy, and a smaller clearance between the piston and cylinder liner. The pistons made of standard and novel alloy were mounted successively in the "W" engine. The full load and part load curves were determined. The lubrication oil consumption, fuel consumption, exhaust emission, blow-by and noise were determined too. The article presents the results of the above-mentioned research. The novel composite alloy enables further engine modernization because the engine should operate at higher pressure and temperature in the combustion chamber.
Źródło:
Journal of KONES; 2017, 24, 4; 99-108
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research performance of novel design of diesel engine
Autorzy:
Kowalski, M.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/949487.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engine
Diesel engine
engine piston
composite alloy
thermal stability
Opis:
Certain results of the comparative studies of the high-speed Diesel engine V-12 of the “W” series were presented in the article. The engine was modernised in regard of possibilities to achieve better performances at specific fuel consumption, smaller exhaust emission, smaller scavenge, lower noise and better thermal stability. The subject of this work is the piston cast of novel composite silumin. The development of novel composite silumin (aluminium-silicon alloy), which contains a little more Copper and Nickel, and the introduction of novel alloyed elements, such as Chromium, Molybdenum, Tungsten, increases the strength of the alloy and its thermal stability during successive heating and cooling. The pistons made of this alloy may have a little bigger outside diameter than the pistons made of PA-12 standard alloy, and a smaller clearance between the piston and cylinder liner. The pistons made of standard and novel alloy were mounted successively in the "W" engine. The full load and part load curves were determined. The lubrication oil consumption, fuel consumption, exhaust emission, blow-by and noise were determined too. The article presents the results of the above-mentioned research. The novel composite alloy enables further engine modernization because the engine should operate at higher pressure and temperature in the combustion chamber.
Źródło:
Journal of KONES; 2017, 24, 4; 99-108
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Some effects of applying a new type of pistons for SU12-U diesel engine
Autorzy:
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/246313.pdf
Data publikacji:
2016
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engines
compression ignition engines
exhaust emissions
combustion engine piston
piston materials
testing of combustion engines
Opis:
In the task of research and development of internal combustion engines, the strong emphasis is placed on reducing emissions of harmful substances in exhaust gases, which include carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxides (NOx), particulate matter (PM, PN); while maintaining a high engine performance and, above all, adequate: power, fuel consumption, noise. One of the possibilities to reduce emissions of HC and engine working noise is to reduce the clearance between the piston and the cylinder liner. This is possible only, when the permanent deformations of the piston are reduced, which result from rapid piston temperature changes (thermal shocks). The newly developed composite aluminum alloy is characterized by high strength parameters and low dimensional hysteresis during repeated heating and cooling. The S12-U engine pistons are made of this material, and they had a slightly larger nominal diameter than the standard pistons. They were then mounted in the engine. The engine was tested on a test stand with the modern, accurate measuring equipment. Test results show, that the HC and CO content in the exhaust gas has been reduced, exhaust gas blowby to the crankcase declined, smoke emission was reduced and engine lubricating oil consumption was also reduced. Analysis of test results indicates that this has been achieved, mainly by reducing the clearances between the piston and the cylinder. The article provides detailed test results, mainly in the form of charts, on which one can compare the results, achieved by the engine with new material pistons with results of the same engine, but with the standard pistons.
Źródło:
Journal of KONES; 2016, 23, 4; 167-174
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-7 z 7

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies