Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "load engine" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
The influence of the engine load on the value and temperature distribution in dry cylinder sleeve
Autorzy:
Gustof, P.
Powiązania:
https://bibliotekanauki.pl/articles/247576.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
numerical techniques
engine load
cylinder sleeve
FEM
Opis:
In this work the influence of the engine load on the value and temperature distribution in dry cylinder sleeve in turbocharged Diesel engine was definition. The computations were performed by means of the original two-zone combustion model, the boundary conditions of III kind and thefinite elements method (FEM) by using of COSMOS/M program. The characteristic surfaces of the cylinder sleeve were analyzed. The registered results of the computations get appointed on experimental measured parameters of the state of the engine work for the excess air number gamma = 1.66 and gamma = 3.08 and for the same engine speed n=2000 rpm. The computations were conductedfor initial 60 seconds of the engine work. On basis of received calculations it was determined that the increase of the engine load at the same engine speed causes the growth of the temperature of cylinder sleeve. Maximum temperature of the dry cylinder sleeve during 60 second of engine work carry out about 420 K for gamma, = 1.66 and 380 K for gamma = 3.08. Moreover the calculations show that top parts of the cylinder sleeve near of the mount flange heat up the most quickly and the temperature below the 3rd ring in outer dead centre of the piston is the lowest. The speed of increase temperature of dry cylinder sleeve is the largest in initial phase of warming up engine. After 10 seconds the average speed of increase temperature carries out about 8 K per second for larger load and about 5 K per second for lower load of the engine. Between 10 and 20 second the speed of increase temperature falls down and it starts stabilizing slowly.
Źródło:
Journal of KONES; 2010, 17, 4; 177-183
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling of the heat load in the piston of turbo diesel engine - continuation
Modelowanie obciążeń cieplnych tłoka doładowanego silnika ZS - kontynuacja
Autorzy:
Gustof, P.
Hornik, A.
Jędrusik, D.
Powiązania:
https://bibliotekanauki.pl/articles/374585.pdf
Data publikacji:
2007
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
silnik z zapłonem samoczynnym
obciążenie cieplne silnika
COSMOS/M
metoda warunków brzegowych
metoda elementów skończonych
turbo diesel engine
heat load in engine
boundary conditions method
finite elements method
Opis:
In this study the mathematical description of characteristic surfaces of the heat exchange of the piston and temperature distribution of the turbo diesel engine at the beginning phase its work was presented. The computations were performed by means of the two-zone combustion model, the boundary conditions of III kind and the finite elements method (MES) by using of COSMOS/M program.
W niniejszym artykule przedstawiono matematyczny opis charakterystycznych powierzchni wymiany ciepła tłoka oraz rozkład ich temperatury dla doładowanego silnika, z zapłonem samoczynnym w początkowej fazie jego pracy. Obliczenia numeryczne zostały przeprowadzone przy zastosowaniu dwustrefowego modelu procesu spalania [1], warunków brzegowych III rodzaju oraz metody elementów skończonych (MES), za pomocą programu COSMOS/M.
Źródło:
Transport Problems; 2007, 2, 4; 81-86
1896-0596
2300-861X
Pojawia się w:
Transport Problems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Koncepcja weryfikacji doświadczalnej zamodelowanych obciążeń cieplnych wybranych elementów komory spalania doładowanego silnika z zapłonem samoczynnym
Conception of the experimental verification the modeling of the heat lodas of the chosen elements of a combustion chamber of the turbocharged diesel engine
Autorzy:
Hornik, A.
Gustof, P.
Powiązania:
https://bibliotekanauki.pl/articles/197835.pdf
Data publikacji:
2012
Wydawca:
Politechnika Śląska. Wydawnictwo Politechniki Śląskiej
Tematy:
weryfikacja doświadczalna
obciążenie cieplne
komora spalania
silnik z zapłonem samoczynnym
experimental verification
thermal load
combustion chamber
compression-ignition engine
Opis:
W niniejszym artykule przedstawiono wyniki matematycznego modelowania obciążeń cieplnych tłoka, tulei cylindrowej, zaworów i gniazd zaworowych, które uzyskano za pomocą dwustrefowego modelu procesu spalania [1], warunków brzegowych III rodzaju oraz metody elementów skończonych (MES). Ponadto w artykule opisano poszczególne etapy przygotowań obiektu badań do weryfikacji doświadczalnej otrzymanych wyników numerycznych wraz z koncepcją stanowiska pomiarowego.
In this paper was presented result of the mathematical modeling of the heat loads in the piston, cylinder sleeve, valves and valves-seats. In calculations used the two-zone combustion model [1] and finite elements method (FEM). Modeling was conducted by use of III kind of the boundary conditions. Moreover in the article were described individual preparation stages of the research object for the experimental verification of received the numerical results along with the concept of the measurements station.
Źródło:
Zeszyty Naukowe. Transport / Politechnika Śląska; 2012, 77; 43-48
0209-3324
2450-1549
Pojawia się w:
Zeszyty Naukowe. Transport / Politechnika Śląska
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies