Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Zydroń, A." wg kryterium: Autor


Wyświetlanie 1-11 z 11
Tytuł:
Właściwości geotechniczne mieszaniny popiołowo-żużlowej ze spalania węgla kamiennego w aspekcie jej przydatności do celów budownictwa ziemnego
Geotechnical Parameters of the Ash-slag Mixture from Hard Coal Burning Concerning Its Usability for Earthworks
Autorzy:
Gruchot, A.
Zydroń, T.
Powiązania:
https://bibliotekanauki.pl/articles/1819047.pdf
Data publikacji:
2013
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
właściwości geotechniczne
budownictwo ziemne
waste
soils
Opis:
In Poland, the production of electricity and thermal energy is based mainly on hard and brown coal burning. It causes great amount of furnace waste, including ash-slag mixtures from wet deposition of waste. According to GUS data in 2010 9 million tons of waste were produced and 253.7 million tons are still on landfills being a burden to the environment. One of possible ways of their usage is earthworks, where ash-slag mixtures are allowed to use in low layers of road embankments, under the condition that they will be built in places that are dry or isolated from water. This restriction is a result of high sensitivity of furnace waste for changes in moisture content as well as their high susceptibility to filtration deformations. There fore it is crucial to determine strength characteristics of this type of materials depending on their moisture content. The purpose of the paper was to determine the influence of moisture content of ash-slag mixture from “Skawina” Power Plant on its shear strength parameters as well as to determine stability of embankments formed from this type of material. Within the scope of laboratory tests, basic geotechnical parameters as well as shear strength parameters and permeability of ash-slag mixture were determined. Shear strength tests were carried out in the standard direct shear box apparatus at the compaction indexes IS = 0.90, 0.95 and 1.00. The moisture content was close to optimal and 5% lower or higher than the optimal moisture content. Permeability tests were carried out with the constant hydraulic gradient on samples at the compaction indexes Is = 0.90 and 1.00. Based on obtained results it was stated that ash-slag mixture from “Skawina” Power Plant has high shear strength parameters and relatively high values of permeability coefficient, although values of these parameters greatly depend on mixture compaction. Additionally shear strength tests showed that the moisture content has a great influence on shear strength parameters. Depending on these tests results and using proposal of calculative model by Matsushi-Matsukury effective strength parameters of the mixture were estimated. Comparing calculations results with parameters obtained from the triaxial shear tests it was stated that the proposed model gives safe values of effective strength parameters so they were used for stability calculations for a model road embankment, which was exposed to heavy rainfall. Infiltration calculations were carried out assuming daily intensity of rainfall on 100 mm/day, which corresponds with 1% probability of rainfall for the Kraków area. These calculations showed, that high permeability of the mixture has a significant influence on the range of changes in the slopes moisture content and the accepted rainfall density was insufficient to saturate this material when there is a free water flow in the embankment’s body. This process can occur only in case of the embankment formed from the mixture on the ground that has lower permeability than the mixture. Calculation results showed that embankment formed from the mixture at high compaction had a high value of safety factor, which indicates that the ash-slag mixture can be a valuable substitute for natural soils.
Źródło:
Rocznik Ochrona Środowiska; 2013, Tom 15, cz. 2; 1719-1737
1506-218X
Pojawia się w:
Rocznik Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Determination of frictional resistance at the contact between chosen furnace waste and geosynthetics
Określenie oporów tarcia na kontakcie wybranych odpadów paleniskowych z geosyntetykami
Autorzy:
Gruchot, A.
Zydron, T.
Powiązania:
https://bibliotekanauki.pl/articles/40542.pdf
Data publikacji:
2015
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
ash-slag mixture
shear strength
determination
frictional resistance
furnace waste
geosynthetic
Opis:
Determination of direct slide coeffi cient and interfacial frictional resistance at the contact between the fill material and geosynthetic was the purpose of the paper. The fill material was an ash-slag mixture from Skawina Power Plant and from the settler of Arcelor-Mittal Poland Steel Plant in Kraków Płaszów. The shear strength and interfacial frictional resistance tests were carried out in the direct shear box apparatus at the moisture content close to optimal at the compaction indexes 0.90, 0.95 and 1.00. Test results revealed that the shear strength parameters of the analyzed ash-slag were high. The parameters describing the frictional resistance at the contact: ash-slag - geosynthetics were also high, which allowed obtaining high values of the direct slide coeffi cient as well as the coefficient of interfacial friction.
Celem badań było określenie wartości współczynnika bezpośredniego poślizgu i oporu tarcia międzyfazowego na kontakcie mieszaniny popiołowo-żużlowej pobranej ze składowiska Elektrowni „Skawina" oraz z osadnika Huty ArcelorMittal Poland w Krakowie Pleszowie a geosynetykiem. Wyniki badań wykazały, że parametry wytrzymałości na ścinanie popioło-żużli były duże. Parametry charakteryzujące opory tarcia na kontakcie mieszanina popiołowo-żużlowa - geosyntetyk były również duże, co pozwoliło uzyskać duże wartości współczynnika bezpośredniego poślizgu, jak również współczynnika tarcia międzyfazowego. W związku z tym wzmacnianie podłoża budowli z wykorzystaniem geo-syntetyków i stosowanie mieszanin popiołowo-żużlowych do celów budownictwa ziemnego jest ważnym i istotnym zagadnieniem w aspekcie ochrony kruszyw naturalnych.
Źródło:
Acta Scientiarum Polonorum. Architectura; 2015, 14, 4
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ opadu deszczu i erozji bocznej na stateczność na przykładzie osuwiska w Bieśniku (Beskid Niski)
Impact of rainfall and lateral erosion on slope stability – case study of shallow landslide in Biesnik (Beskid Niski Mountains)
Autorzy:
Zydron, T.
Gruchot, A.
Powiązania:
https://bibliotekanauki.pl/articles/40548.pdf
Data publikacji:
2016
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
Beskid Niski
wies Biesnik
zbocza
statecznosc zboczy
osuwiska
opady atmosferyczne
deszcze
erozja boczna
Beskid Niski Mountains
Biesnik village
slope
slope stability
landslide
atmospheric precipitation
rain
lateral erosion
Opis:
Celem pracy było określenie wpływu opadu deszczu i erozji bocznej na warunki stateczności zbocza położonego w pobliżu potoku Szalówka. Obszar badań to jedno z osuwisk Karpat fliszowych w miejscowości Bieśnik k. Gorlic (Beskid Niski), które powstało w 2010 roku. Badania obejmowały terenowe i laboratoryjne określenie właściwości geotechnicznych gruntów, a także obliczenia stateczności z uwzględnieniem infiltracji opadu oraz podcięcia jego podstawy. Wykazały one, że analizowane osuwisko powstało w terenie o niekorzystnych warunkach geotechnicznych z przewagą słabo przepuszczalnych utworów ilastych oraz łupków ilastych w stanie plastycznym i miękkoplastycznym. Z kolei obliczenia stateczności wykazały istotny wpływ opadu deszczu i procesów fluwialnych (erozji bocznej) na warunki równowagi zbocza.
The analysis of influence of rainfall infiltration and lateral erosion of riverbank on slope stability is presented in the paper. Studied landslide is situated at the Flysch Carpathians (Bieśnik near Gorlice, Beskid Niski Mts.) and it was activated in 2010. Field and laboratory tests included land surveying measurements and determination of geotechnical parameters of soils. In the further part of work were done slope stability calculations, which included influence of infiltration process and erosion range at the toe of slope on stress state change within the slope. Tests revealed, that analyzed landslide originated in the area of the unfavorable geological conditions, where subsoil is composed of poorly permeable clays and schists of medium and high plasticity. In turn, the slope stability calculations have shown a significant and of a similar scope of the impact of rainfall and fluvial processes (lateral erosion) on stability of the analyzed slope.
Źródło:
Acta Scientiarum Polonorum. Architectura; 2016, 15, 3
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impact of a Test Method on the Undrained Shear Strength of a Chosen Fly Ash
Autorzy:
Gruchot, A.
Zydroń, T.
Powiązania:
https://bibliotekanauki.pl/articles/125295.pdf
Data publikacji:
2016
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
fly ash
shear strength
ultimate resistance of the subsoil
Opis:
The paper presents an assessment of the suitability of a laboratory vane apparatus, a cone penetrometer as well as a shear vane tester and a pocket penetrometer for determination of the parameters of the undrained shear strength of fly ash from the Power Plant “Skawina”. The suitability of the cone penetrometer and the laboratory vane apparatus for the determination of the undrained shear strength of the fly ash has been shown. On the bases of the obtained test results, , drained and undrained shear strengths of the subsoil made of the fly ash under the square pad foundation were calculated according to Eurocode 7. The calculations of the ultimate resistance of the drained subsoil showed that it was several times bigger than its value in undrained conditions. This confirms the need for the proper determination of the angle of internal friction and cohesion as well as the undrained shear strength of fly ashes.
Źródło:
Journal of Ecological Engineering; 2016, 17, 4; 41-49
2299-8993
Pojawia się w:
Journal of Ecological Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zastosowanie funkcji Weibulla do oceny wytrzymałości na rozciąganie korzeni wybranych gatunków drzew
Application of the Weibull survival function for estimation of the root tensile strength of selected tree species
Autorzy:
Zydron, T.
Gruchot, A.
Czesak, K.
Powiązania:
https://bibliotekanauki.pl/articles/40503.pdf
Data publikacji:
2018
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
drzewa
brzoza brodawkowata
grab pospolity
sosna zwyczajna
korzenie
wytrzymalosc na rozciaganie
wzmocnienia gruntu
model wiazkowy
funkcja Weibulla
tree
common birch
Betula pendula
European hornbeam
Carpinus betulus
Scotch pine
Pinus sylvestris
root
tensile strength
Weibull distribution
Źródło:
Acta Scientiarum Polonorum. Architectura; 2018, 17, 4
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of randomly oriented fibres on shear strength of mineral soils
Autorzy:
Zydroń, T.
Gruchot, A.
Konat, P.
Powiązania:
https://bibliotekanauki.pl/articles/971477.pdf
Data publikacji:
2019
Wydawca:
Uniwersytet Marii Curie-Skłodowskiej. Wydawnictwo Uniwersytetu Marii Curie-Skłodowskiej
Tematy:
shear strength
fibre reinforcement
reinforced sand
reinforced clayey silt
Opis:
The purpose of the paper was to determine two things: the influence of type and amount of reinforcement on shear strength of soil and the relation between the efficiency of reinforcement and soil moisture content. Shear strength was determined in a direct shear apparatus in a box with a square section of 80x80 mm. The range of normal stress was from 25 to 150 kPa and the shear velocity was 1.0 mm×min⁻¹. The tests were carried out on medium sand and clayey coarse silt at two moisture contents and with two types of reinforcement - polyolefine fibres and 40x3 mm foil stripes. The addition of reinforcement was 0.5 and 1.0% in relation to the dry mass of soil. Test results indicated that using polyolefine fibres as dispersed reinforcement in a sandy soil increased its shear strength. Whereas the influence of using foil stripes on shear strength was little. However, using both types of reinforcement in a cohesive soil increased its shear strength and this influence was particularly clear at higher moisture content.
Źródło:
Polish Journal of Soil Science; 2019, 52, 2; 235-246
0079-2985
Pojawia się w:
Polish Journal of Soil Science
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ prędkości ścinania na kształtowanie się parametrów wytrzymałościowych gruntów z obszaru karpackiego
Influence of shear speed on the shear-strength of soils from the Carpatians region
Autorzy:
Zydroń, T.
Kogut, M.
Gruchot, A.
Powiązania:
https://bibliotekanauki.pl/articles/349976.pdf
Data publikacji:
2011
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
wytrzymałość na ścinanie
prędkość ścinania
osuwiska
shear strength
shear speed
landslides
Opis:
W artykule przedstawiono wyniki badań wytrzymałości na ścinanie gruntów spoistych pochodzących z sąsiedztwa obszarów osuwiskowych w Chalakówce (Pogórze Wielickie), Krynicy (Beskid Sądecki), Ropicy Polskiej (Beskid Mały) i Targanic (Beskid Mały). Celem pracy było określenie wpływu prędkości ścinania na wartości maksymalnych i minimalnych parametrów wytrzymałościowych badanych gruntów. Badania przeprowadzono w aparacie bezpośredniego ścinania produkcji o wymiarach skrzynki 60x60 mm na materiale pozbawionym ziaren grubszych od 2 mm. Próbki formowano bezpośrednio w skrzynce aparatu przy wilgotności naturalnej i ścinano przy trzech prędkościach 0,1; 1,0 i 10 mm/min. Każda próbka była ścinana 3-krotnie do uzyskania odkształceń względnych 20%, a w trakcie badań woda miała możliwość penetracji w obręb płaszczyzny ścięcia. Wykazano, że zawodnienie wytworzonej w trakcie ścinania gruntów powierzchni poślizgu prowadzi do zmniejszenia ich początkowej wytrzymałości na ścinanie w skrajnych przypadkach nawet o 80%. Istotnym czynnikiem wpływającym na kształtowanie się oporu na ścinanie gruntów jest prędkość odkształceń. Większe wartości maksymalnego oporu na ścinaniu badanych gruntów otrzymano przy większych prędkościach ścinania. Z kolei w zakresie dużych odkształceń mniejsze wartości wytrzymałości na ścinanie odnotowano przy większych prędkościach ścinania.
The results of shear-strength tests performed on cohesive soils taken from landslide prone's areas from Chalakówka (Pogórze Wielickie), Krynica (Beskid Sądecki Mts.), Ropica Polska (Beskid Mały Mts.) and Targanice (Beskid Mały Mts.) are presented in the paper. The aim of the tests was determination of influence of shearing speed on maximum and minimum shear strength of tested soils. The tests were carried out in a standard direct shear apparatus of dimensions of the box 60x60 mm on soils on materials without grains coarser than 2 mm. The samples were formed directly in the box of the apparatus at the natural moisture content. Shear speed were equal to 0.1; 1.0 and 10 mm/min. Each sample were sheared three times up to obtain the relative horizontal displacement of 20%. During shearing the sliding surface was watering. On the basis of the obtained results, one can state that the watering of shearing surface cause decrease of initial (maximum) shear strength of soils up to 80%. The another important factor controlling shear resistance of soils is shearing speed. Increase of shearing speed caused increase maximum shear strength of tested soils. On the other hand, increase of shearing speed caused decrease of minimum shear strength (obtained during third shearing at large horizontal displacement).
Źródło:
Górnictwo i Geoinżynieria; 2011, 35, 2; 619-626
1732-6702
Pojawia się w:
Górnictwo i Geoinżynieria
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Parametry wytrzymałościowe fluidalnego popiołu lotnego z Elektrowni „Połaniec”
Mechanical Properties of Fluidized Fly Ash from Power Station “Połaniec
Autorzy:
Gruchot, A.
Zydroń, T.
Gałowicz, E.
Powiązania:
https://bibliotekanauki.pl/articles/1818638.pdf
Data publikacji:
2015
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
fluidalny popiół lotny
wytrzymałość na ścinanie
wskaźnik nośności CBR
wytrzymałość na ściskanie
budownictwo drogowe
fluidized fly ash
shear strength
CBR ratio
compressive strength
road construction
Opis:
Production of electricity and heat energy in Poland is largely based on the combustion of coal and lignite in power plants. Combustion of coal is associated with the production of significant quantities of wastes. Given the possibilities of their using, the most important product of combustion is fly ash and recently – fluidized fly ash. Tests on properties of fluidized fly ash are mainly focused on determining the impact of its addition on the mechanical properties of concrete or the setting time of self-hardening slurries, while little is known about its mechanical parameters. The aim of the study was to determine the impact of density, moisture content and maintenance duration on shear strength, CBR ratio and compressive strength of fluidized fly ash from Power Plant "Połaniec". The study was performed in terms of assessing their possibility of use for the purpose of road construction. CBR ratio was determined at three various values of moisture content determined from compaction curve of the fly-ash. CBR ratio tests were done for samples directly after compaction and after 4 days of the soaking in water. Shear strength was determined in a direct shear apparatus on samples compacted at a moisture content close to the optimum and three values of the compaction index IS = 0.90, 0.95 and 1.00. Determination of compressive strength was carried out on samples immediately after preparation and after 7, 14, 28 and 42 days of air, air-water and air-water maintenance process including 3, 7, and 14 cycles of freezing and de-freezing. The results revealed that in accordance with the geotechnical nomenclature the tested fluidized fly-ash's grain-size distribution corresponds to sandy silts. The fly-ash has high value of maximum dry density. CBR ratio of fly-ash samples after 4 days of soaking in water were very high and ranged from 199 to 277%. It can be underline that in case of both tests series, the obtained CBR indexes were positively correlated with increasing initial moisture content of tested samples. The parameters of the shear strength were high. It was stated that the higher values of compaction indexes, the higher values of the angle of internal friction and cohesion were obtained. The compressive strength of samples was high, ranging from over 2.2 MPa to approximately 6.0 MPa. The largest increase in strength was obtained after 7 days of maintenance. The maximum values of compressive strength after 42 days of maintenance, were obtained for samples which were subjected to air and air-water maintenance process. Freeze-thaw resistance index value obtained for a short 3 cycles of freezing and de-freezing process was greater than 1.0, which means that tested fly-ash was not prone to freezing process. Increasing number of freezing and de-freezing cycles affected the freeze-thaw resistance index value, which was well below 1.0, indicating a significant loss of compressive strength. To sum up, the test results on the fluidized fly ash from Power Plant "Połaniec" revealed that the fly-ash has good compaction properties, bearing capacity and shear strength. In contrast, the particle size of the fly-ash is unfavorable from the viewpoint of its use in road embankments. In turn, the results of the CBR and compressive strength tests confirmed the presence of hydration properties of fluidized fly ash thus indicating the possibility of its use in road hydraulic binders.
Źródło:
Rocznik Ochrona Środowiska; 2015, Tom 17, cz. 2; 1622-1641
1506-218X
Pojawia się w:
Rocznik Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badania właściwości geotechnicznych pokryw stokowych dolin potoków Jamne i Jaszcze w Gorcach
Research of geotechnical properties of slope covers from Jamne and Jaszcze stream valleys in Gorce Mts
Autorzy:
Zydroń, T.
Gruchot, A.
Demczuk, P.
Bucała-Hrabia, A.
Powiązania:
https://bibliotekanauki.pl/articles/400669.pdf
Data publikacji:
2018
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
Gorce
wytrzymałość na ścinanie
stateczność zboczy
probabilistyczna ocena stateczności
shear strength
slope stability
probabilistic slope stability analysis
Opis:
W pracy przedstawione zostały wyniki badań parametrów geotechnicznych gruntów stanowiących pokrywy stokowe dwóch dolin potoków górskich w Gorcach w aspekcie oceny ich podatności osuwiskowej. Badania terenowe obejmowały określenie podstawowych właściwości fizycznych gruntów na kilku stanowiskach zlokalizowanych na zboczach obydwu dolin. Natomiast badania laboratoryjne obejmowały oznaczenie składu uziarnienia, granic konsystencji, współczynnika filtracji oraz wytrzymałości na ścinanie w aparacie bezpośredniego ścinania próbek zawodnionych oraz w aparacie trójosiowego ściskania metodą CIU. Wyniki badań wykazały, że badane grunty można określić jako utwory gruboziarniste z nieznaczną zawartością frakcji ilastej, charakteryzujące się niską plastycznością. Wartości kąta tarcia wewnętrznego większości badanych gruntów były wysokie i wahały się w zakresie od 28 do 38° , a spójności od 0 do 7 kPa. Generalnie większe wartości kąta tarcia wewnętrznego, a mniejsze spójności uzyskano z badań w aparacie trójosiowego ściskania. Współczynniki infiltracji z badań terenowych pozwalają scharakteryzować badane utwory jako średnio-przepuszczalne. Obliczenia stateczności wykonane z wykorzystaniem modelu SINMAP wykazały, że znaczna część analizowanego obszaru jest narażona na ruchy masowe, co daje bardziej konserwatywną oceną podatności osuwiskowej niż podają wyniki opracowane w programie SOPO. Z kolei probabilistyczna ocena stateczności wskazuje, że prawdopodobieństwo utraty stateczności wzrasta na zboczach o nachyleniu przekraczającym 20°, a uzyskane wyniki obliczeń pozwalają uzyskać bardziej szczegółowy obraz podatności rozpatrywanego obszaru na ruchy masowe niż uzyskano stosując model SINMAP.
Test results of geotechnical parameters of slope covers from valleys of two mountainous streams from Gorce Mts. are presented in the paper. The tests were carried out in the context of estimation of slope stability of analyzed watersheds. Field studies included determination of basic soil physical properties at several sites within studied area, laboratory tests involved determination of particle size distribution, consistency limits, permeability coefficients and shear strengths, which were carried out at direct shear box and CIU tests in triaxial apparatus. Test results revealed that tested slope covers can be described as coarse-grained soils with low content clay fraction, characterized by low plasticity. The values of the internal friction angle of the average bad land were high and ranged from 28 to 38 degrees, whereas cohesion varied from 0 to 7 kPa. Generally higher values of angle of internal friction and lower cohesion were obtained from triaxial tests. Values of permeability coefficients determined using infiltration method allow to characterize tested soils as a semi-permeable medium. Stability calculations using the SINMAP model have shown that a significant part of the analyzed area is prone to mass movements, giving a more conservative assessment of landslide vulnerability than results of the SOPO report. The likelihood of slope failure increases significantly on slopes of inclination exceeding 20 degrees, and the results of the calculations obtained the method provide a more detailed information of the mass movements susceptibility of the area than were obtained using the SINMAP model.
Źródło:
Inżynieria Ekologiczna; 2018, 19, 1; 44-52
2081-139X
2392-0629
Pojawia się w:
Inżynieria Ekologiczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ wskaźnika pokrycia liściowego (LAI) na stateczność zboczy
Influence of leaf area index (LAI) on slope stability
Autorzy:
Zydroń, T.
Demczuk, P.
Gruchot, A.
Siłuch, M.
Klimek, M.
Powiązania:
https://bibliotekanauki.pl/articles/949864.pdf
Data publikacji:
2016
Wydawca:
Polskie Towarzystwo Inżynierii Ekologicznej
Tematy:
stateczność zboczy
wskaźnik pokrycia liściowego LAI
opad progowy
slope stability
Leaf Area Index (LAI)
threshold rainfall
Opis:
Celem pracy było określenie wpływu wartości wskaźnika pokrycia liściowego (LAI) na wyniki obliczeń stateczności stoku osuwiskowego położonego we wschodniej części Pogórza Wiśnickiego w miejscowości Gwoździec. Obliczenia zostały przeprowadzone w modułach VADOSE/W i SLOPE/W programu GeoStudio 2012 i polegały na integracji obliczeń infiltracji wody opadowej z obliczeniami stateczności. W efekcie obliczeń określono warunki opadowe (długość trwania i sumę opadu) powodujące naruszenie stateczności zbocza (tzw. opad progowy). Wyniki obliczeń wykazały, że wartości LAI z zakresu 1–3, odpowiadające roślinności trawiastej, sprzyjają w dłuższej perspektywie czasu gromadzeniu się wody gruncie, co ogranicza jego zdolność retencji w momencie wystąpienia intensywnych opadów. Z kolei pokrycie terenu, tożsame z wartością LAI=5 odpowiadającymi drzewom, powoduje zwiększenie zdolności retencyjnej gruntów, co wpływa na opóźnienie reakcji gruntu na opady (utratę stateczności zboczy) w stosunku do terenu pokrytego roślinnością trawiastą. Stwierdzono również, że warunki wilgotnościowe panujące w zboczu przed rozpoczęciem intensywnych opadów mają znaczący wpływ na wielkość opadu progowego i w przypadku analizowanego zbocza wyniosły one od 90 mm dla okresu mokrego do ponad 700 mm dla okresu suchego.
Determination of effect of the leaf area ratio on the results of slope stability calculation of one of the landslide prone slope located in the Pogórze Wiśnickie was presented in the paper. The calculations were carried out in modules Vadose/W and SLOPE/W of package GeoStudio 2012. The calculations involved the integration of rainfall infiltration process and slope stability calculations. As a result, the calculations allow to determinate precipitation conditions (time and accumulated precipitation height) causing slope failure (i.e. rainfall threshold). The calculation results showed significant impact of LAI on the results of modeling. It was revealed, that LAI values in range 1–3, corresponding to the grass vegetation, contribute in long-term to accumulation of precipitation within slope, which limits its retention ability when intense rainfalls occur. In turn, the leaf are index LAI = 5, corresponding to the coverage of trees, increase the retentive capacity of the soil, which resulting in delayed response of slope on rainfall with in comparison to an area covered with grass plants. It was also found significant impact of moisture content conditions on rainfall threshold. It was revealed that in case of analyzed slope threshold rainfall can be comprised from 90 mm to over 700 mm.
Źródło:
Inżynieria Ekologiczna; 2016, 49; 81-90
2081-139X
2392-0629
Pojawia się w:
Inżynieria Ekologiczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wykorzystanie spektrometrii impedancyjnej do monitorowania przepływu filtracyjnego przez nasypy hydrotechniczne
Use of impedance spectrometry for monitoring filtration flow through hydrotechnical embankments
Autorzy:
Gruchot, A.
Zydron, T.
Parilkova, J.
Zachoval, Z.
Cholewa, M.
Kos, K.
Powiązania:
https://bibliotekanauki.pl/articles/40887.pdf
Data publikacji:
2018
Wydawca:
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie. Wydawnictwo Szkoły Głównej Gospodarstwa Wiejskiego w Warszawie
Tematy:
budowle ziemne
budowle hydrotechniczne
stan techniczny
nasypy hydrotechniczne
przeplyw filtracyjny
monitoring
spektrometria impedancyjna
earthen structure
hydraulic structure
technical state
filtration flow
impedance spectroscopy
Źródło:
Acta Scientiarum Polonorum. Architectura; 2018, 17, 1
1644-0633
Pojawia się w:
Acta Scientiarum Polonorum. Architectura
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-11 z 11

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies