Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Krenicky, Tibor" wg kryterium: Autor


Wyświetlanie 1-6 z 6
Tytuł:
Casting machines and properties of Al-Si castings alloys
Autorzy:
Ružbarský, Juraj
Krenický, Tibor
Maščeník, Jozef
Coranič, Tomáš
Powiązania:
https://bibliotekanauki.pl/articles/2175487.pdf
Data publikacji:
2022
Wydawca:
STE GROUP
Tematy:
die casting
technological parameters
machines
die casting pressure
pressing speed
odlewanie ciśnieniowe
parametry technologiczne
maszyny
Opis:
The paper focuses on the research of holding pressure inside the mould cavity and pressing speed as technological parameters of die casting. The experiments conducted within the frame of the practical part examined the plunger and the pressure or the holding pressure in the mould cavity influencing the mechanical properties of a casting which were represented by ultimate tensile strength and percentage share of porosity of Al-Si castings. The results of experiments and analysis of the measured values proved the relation between pressure, or holding pressure, in the mould cavity and the ultimate tensile strength and porosity of castings. Plunger pressing speed is closely related to mould cavity filling mode which affected the final porosity of casting. It can be assumed that die casting is positively influenced by the increase of ultimate tensile strength and reduction of porosity during the increase of pressure or of holding pressure in the mould cavity. Higher values of holding pressure caused the elimination of pores which resulted in a decrease in the percentage share of pores in the casting and an increase in values of ultimate tensile strength.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2022, 11, 2; 8--34
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Design of self-leveling table for FFF additive technology
Autorzy:
Coranič, Tomáš
Ružbarský, Juraj
Krenický, Tibor
Maščeník, Jozef
Powiązania:
https://bibliotekanauki.pl/articles/27323744.pdf
Data publikacji:
2023
Wydawca:
STE GROUP
Tematy:
additive technologies
calibration
Arduino
structural design
technologie addytywne
kalibrowanie
projekt konstrukcyjny
Opis:
The presented paper describes the conceptual design of a worktable intended mainly for use in combination with FFF additive technologies, calibrated using a gyroscope and accelerometer. The proposed system is based on a programmable Arduino platform that operates with three digital servomotors and a mechanical gyroscope. In the introduction, the theoretical assumptions, and definitions of basic concepts such as a gyroscope, electric motor, and RC servomotor are described. Subsequently, the contribution is devoted to the selection of suitable components, the schematic connection, and the design itself in the Autodesk Inventor program. In the conclusion, the anticipated benefits of using the technical solution when applied in FFF additive technologies are described.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2023, 12, 2; 109--117
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Options for solutions of the inlet system into the mold
Autorzy:
Ružbarský, Juraj
Krenický, Tibor
Maščeník, Jozef
Coranič, Tomáš
Powiązania:
https://bibliotekanauki.pl/articles/27323743.pdf
Data publikacji:
2023
Wydawca:
STE GROUP
Tematy:
pressure casting
mold construction
inlet system
pressure
odlewanie ciśnieniowe
konstrukcja formy
układ wlotowy
ciśnienie
Opis:
The presented contribution points out the possibilities of solving the inlet system, as one of the important factors influencing the final quality of the castings. Due to its design and function, the sprue system influences the process of filling the mold cavity. With the correct design of the sprue system, we achieve the continuity of filling the mold cavity and the elimination of qualitative and quantitative errors caused by non-observance of basic principles in the design of sprue systems. When conducting the experiments, we monitored the mold inlet system, modeling the process of filling the mold cavity and the speed of the liquid metal in the notch and the mold cavity. The results of the experiments show that the speed of the liquid metal when filling the mold is approximately half of the calculated theoretical value.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2023, 12, 2; 57--70
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Technical diagnostics of industrial double twist twinner machine for data cables
Autorzy:
Krenický, Tibor
Ružbarský, Juraj
Coranič, Tomáš
Maščeník, Jozef
Powiązania:
https://bibliotekanauki.pl/articles/2175488.pdf
Data publikacji:
2022
Wydawca:
STE GROUP
Tematy:
vibrodiagnostics
maintenance
twisted pair cables
return loss
cable fault
wibrodiagnostyka
konserwacja
kable typu skrętka
usterka kabla
Opis:
The presented article focuses on the diagnostic measurement and evaluation of vibrations of equipment used for data-cable twisted pairing manufacture. A short description of the process of the data cables manufacturing process to which the diagnosed device belongs is provided and the qualitative parameters of the data cables are mentioned. The experimental part is devoted to the experimental diagnostics of the given system in order to locate and identify the possible reason for the occurrence of the parameter´s critical value of the loss of the data cable. When deterioration of electric properties was detected, monitoring the basic oscillation characteristics has been deployed as the key tool to detecting damaged machine parts, and avoiding quality deterioration of the products in the manufacturing process. Finally, the quality of the paired cables after the repair has been confirmed by measurements verifying the efficiency of the measures performed.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2022, 11, 2; 35--46
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Measurement of dynamic characteristics of screw conveyor
Autorzy:
Coranič, Tomáš
Maščeník, Jozef
Ružbarský, Juraj
Krenický, Tibor
Powiązania:
https://bibliotekanauki.pl/articles/2175491.pdf
Data publikacji:
2022
Wydawca:
STE GROUP
Tematy:
software
modal analysis
screw conveyor
vibration
oprogramowanie
analiza modalna
przenośnik ślimakowy
wibracje
Opis:
A machine has always been, is and will be the technical progress. The basis of every economy is the progressiveness of manufacturing engineering since it manufactures components for all industries. Technical requirements in manufacturing engineering are constantly leading to an increase of the technical level of manufacturing equipment. Profound knowledge of scientific fields precedes a successful fulfilment of the technical requirements. Structural units of manufacturing machines are complex mechanisms that must work reliably and safely with an emphasis on their important function. These units create new objectives for their research and optimization.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2022, 11, 2; 66--76
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
New concept of software for calculation of chain gears
Autorzy:
Maščeník, Jozef
Coranič, Tomáš
Krenický, Tibor
Ružbarský, Juraj
Powiązania:
https://bibliotekanauki.pl/articles/2175493.pdf
Data publikacji:
2022
Wydawca:
STE GROUP
Tematy:
software
design
chain gear
calculation
strength
oprogramowanie
projektowanie
przekładnia łańcuchowa
obliczanie
wytrzymałość
Opis:
At present, practically all areas of design activities are supported by computer technology, which can be effectively used in the design of gears, belts and chain transmissions, especially in the field of calculations, as well as graphics solutions. However, their use requires mastering the basic principles of computational procedures contained in the programs in question and, on that basis, critically evaluating computer-generated solutions. The presented paper deals with the design proposal and application of program for calculation and check of chain gears. Although there are currently various programs on the market that can design chain transmissions and perform strength analysis, there is still space for improvement and the creation of these programs. The computing program has been created as a spreadsheet in the working environment of the Microsoft Office program by the Excel application through defined sequences of the individual commands. The program serves for design proposal of a chain drive by means of inserted databases, graphs and tables. In the process of designing and checking the input values are entered such as performance, rotations, and number of wheels. Through calculation the software generates speed of a chain, circumferential speed, tensile force, number of chain links, axial distance, etc. At the same time the paper compares generated parameters with manual calculation of the chain gear.
Źródło:
Systemy Wspomagania w Inżynierii Produkcji; 2022, 11, 2; 47--56
2391-9361
Pojawia się w:
Systemy Wspomagania w Inżynierii Produkcji
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-6 z 6

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies