Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "81.15.Aa" wg kryterium: Temat


Wyświetlanie 1-10 z 10
Tytuł:
Preparation and Electrochemical Performance of ZnO Films as Anode Materials for Li-Ion Batteries
Autorzy:
Cevher, O.
Cetinkaya, T.
Tocoglu, U.
Guler, M.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1399886.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.05.Dz
81.15.Cd
82.47.Aa
Opis:
In this work, the effect of rf power on the structural, electrical and electrochemical properties of ZnO thin films was investigated. ZnO thin films were deposited on glass and Cr coated stainless steel substrates by rf magnetron sputtering in pure Ar gas environment. ZnO thin films for different rf powers (75, 100, and 125 W) were deposited keeping all other deposition parameters fixed. ZnO thin films were used as negative electrode materials for lithium-ion batteries, whose charge-discharge properties, cyclic voltammetry and cycle performance were examined. A high initial discharge capacity about 908 mAh g^{-1} was observed at a 0.5 C rate between 0.05 and 2.5 V. The crystallographic structure of the sample was determined by X-ray diffraction. The electrical resistivity of the deposited films was measured by the four-point-probe method. The thickness of the ZnO thin films was measured using a profilometer.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 355-357
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cr and V Substitution in the LiMn₂O₄Spinel Positive Electrode Li-Ion Batteries
Autorzy:
Akbulut, A.
Cetinkaya, T.
Guler, M.
Uysal, M.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1401245.pdf
Data publikacji:
2015-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
82.47.Aa
81.20.Fw
81.15.-z
Opis:
In this study, $LiCr_{0.2}V_{0.4}Mn_{1.4}O_4$ cathode active electrode materials were produced via a facile sol-gel method at 800°C. The surfaces of the $LiCr_{0.2}V_{0.4}Mn_{1.4}O_4$ cathode active electrode materials were then coated with Cu in order to increase the conductivity and suppress the manganese ion dissolution into the electrolyte. The structure and electrochemical properties of the obtained Cr and V substituted LiMn₂O₄ powders were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), galvanostatic charge- discharge test and electrochemical impedance spectroscopy (EIS). The improvement in the cycling performances attributed to stabilization of spinel structure by bication ion substation and Cu coating on the spinel particles. EIS analysis confirmed that bication doping and conductive Cu coating contributed stability of the spinel electrodes and provided stable electrolyte/electrode interface due to the suppression of electrolyte decomposition
Źródło:
Acta Physica Polonica A; 2015, 127, 4; 1019-1022
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Electrochemical Performance of Pulse Electrodeposited Sn-Ni/MWCNT Composite Anode for Lithium-Ion Batteries
Autorzy:
Uysal, M.
Görmüş, H.
Karslıoğlu, R.
Alp, A.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1218848.pdf
Data publikacji:
2014-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
81.15.Pq
82.47.Aa
81.05.Mh
Opis:
Grain size, and MWCNT content in the electrolyte of nanocrystalline Sn-Ni/MWCNT composite deposits produced from a solution containing nickel chloride and tin chloride at constant electrodeposition conditions (pulse on-time $T_{on}$ at 2.5 ms and pulse off-time $T_{off}$ at 7.5 ms) but with different peak current densities were investigated. The structure of the electroplated thin film Sn-Ni/MWCNTs composite electrode is investigated by X-ray diffraction, scanning electron microscopy. Galvanostatic charge/discharge measurements were performed in the assembled CR2016 cells designed by using anode composite material produced by pulse electro co-deposition. These cells discharge capacities were cyclically tested by a battery tester at a constant current in voltage range between 0.02 and 1.5 V. The electrochemical results showed that the increase in the discharge capacity of the assembled cell was produced when compared with conventionally used graphite lithium-ion batteries.
Źródło:
Acta Physica Polonica A; 2014, 125, 2; 353-356
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Nanostructured Silicon Thin Film Electrodes for Li-Ion Batteries
Autorzy:
Tocoglu, U.
Cetinkaya, T.
Cevher, O.
Oguz Guler, M.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1399941.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
61.72.uf
81.15.Cd
82.47.Aa
Opis:
In this study we produced nanostructured silicon thin films as lithium ion battery electrodes. Films were sputtered onto stainless steel substrates from high purity silicon target via dc magnetron sputtering technique with using different powers. Morphology and crystal structure of films were characterized with the use of scanning electron microscopy, X-ray diffraction and energy dispersive spectroscopy analysis, respectively. The thickness of films was measured by using surface profiler. Coin type test cells were assembled in argon filled glove box. Electrochemical performance of cells was tested on an electrochemical analyzer using constant current densities over a voltage range of 0.2-2 V.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 380-382
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Electrochemical Performance of SnO₂ and SnO₂/MWCNT/Graphene Composite Anodes for Li-Ion Batteries
Autorzy:
Cevher, O.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1032560.pdf
Data publikacji:
2017-01
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
61.72.uj
81.15.Cd
82.47.Aa
Opis:
In this study, tin oxide (SnO₂) coatings on Cr coated stainless steel and multi-walled carbon nanotube (MWCNT)/graphene substrates were prepared using a radio frequency magnetron sputtering process as anode materials in lithium-ion batteries. SnO₂ thin film and SnO₂/MWCNT/graphene composite were characterized with field-emission scanning electron microscopy, X-ray diffraction, and electrochemical tests (cyclic voltammetry and galvanostatic cycling). The electrochemical properties of SnO₂ and SnO₂/MWCNT/graphene composite anodes were studied using 2016-type coin cells assembled in an argon-filled glove box. The cells were cyclically tested on a MTI BST8-MA battery analyzer. The cyclic voltammograms of SnO₂ anode and SnO₂/MWCNT/graphene composite anode were obtained over the potential range of 0.05-3.0 V and 0.05-2.5 V at a scan rate of 0.05 mV s¯¹, respectively.
Źródło:
Acta Physica Polonica A; 2017, 131, 1; 204-206
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Electrochemical Properties of Cu Coated $LiCr_{0.2}V_{0.2}Mn_{0.6}O_2$ Nanocomposites for High Rate Li-Ion Batteries
Autorzy:
Algul, H.
Erdas, A.
Tokur, M.
Guler, M.
Akbulut, H.
Alp, A.
Powiązania:
https://bibliotekanauki.pl/articles/1401278.pdf
Data publikacji:
2015-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
82.47.Aa
81.15.-z
88.80.ff
Opis:
Several reported problems of commercial LiCoO₂ electrode materials such as high cost, toxicity, limited rate capability and safety concerns are still remain to be problematic to develop the lithium ion consumer electronics such as mobile phones, tablets and notebook computers. In this study, an alternative nanocomposite electrode material based on $LiCr_{0.2}V_{0.2}Mn_{0.6}O_2$ and copper coated one were produced via a facile sol-gel method and electroless Cu deposition techniques. The resulting samples were characterized by X-ray diffraction (Rigaku DMax 2200 diffractometer) using a monochromatized Cu-Kα source (λ=1.5406 Å) and 2θ scan range from 10° to 80° with a speed of 1° $\text{min}^{-1}$. The scanning electron microscope (SEM) was used in order to characterize the morphology of the active materials. The as-synthesized $Cu//LiCr_{0.2}V_{0.2}Mn_{0.6}O_2$ composite cathode exhibits a stable capacity on cycling and good rate capability after 50 cycles and total capacity retention of 93% is obtained. The unique 2D structure of the composite cathode material, its good electrochemical performances and its relatively low cost comparing to LiCoO₂, make this material very promising for applications.
Źródło:
Acta Physica Polonica A; 2015, 127, 4; 1038-1041
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Nanostructured ATO Anodes Produced by RF Magnetron Sputtering for Li-Ion Batteries
Autorzy:
Cevher, O.
Tocoglu, U.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1401282.pdf
Data publikacji:
2015-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
61.72.uj
81.15.Cd
82.47.Aa
Opis:
In this study, the reversible capacities, as well as the cycling behavior, of crystalline antimony-doped tin oxide (ATO) films have been investigated. ATO films were deposited on Cr-coated stainless steel substrates by the RF magnetron sputtering technique, with antimony-doped tin oxide (SnO₂:Sb) target in a mixed oxygen/argon gas environment. The ATO films were deposited for 1.0 h in a mixture of Ar and O₂ environment with O₂/Ar ratio of 10/90, at sputtering power of 75 W, 100 W and 125 W RF. ATO films were examined by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM). The electrochemical properties of ATO anodes were studied using 2016-type coin cells assembled in an argon-filled glove box.
Źródło:
Acta Physica Polonica A; 2015, 127, 4; 1065-1067
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Preparation and Characterization of Copper Powders with Sn Coating by the Electroless Plating
Autorzy:
Uysal, M.
Cetinkaya, T.
Gul, H.
Kartal, M.
Algul, H.
Tokur, M.
Alp, A.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1401294.pdf
Data publikacji:
2015-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
82.47.Aa
81.15.-z
73.61.At
Opis:
In this work, Sn-Cu composite powders were produced using an electroless process. The tin content on the surface of copper powders was varied by using different concentrations of SnSO₄ in the plating bath. The surface morphology of the produced Sn-Cu composite powders was characterized using scanning electron microscopy (SEM). Energy dispersive spectroscopy (EDS) was used to determine the elemental surface composition of the composites. X-ray diffraction (XRD) analysis was performed to investigate the structure of the Sn-Cu composite powders. The electrochemical performance of Sn-Cu nanocomposites was studied by charge/discharge tests.
Źródło:
Acta Physica Polonica A; 2015, 127, 4; 1106-1108
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigation of Tin Oxide Based Nanocomposites for Li-Ion Batteries
Autorzy:
Cevher, O.
Cetinkaya, T.
Tocoglu, U.
Guler, M.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1399889.pdf
Data publikacji:
2013-02
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
88.30.rh
81.05.Dz
81.15.Cd
82.47.Aa
Opis:
In this work, tin oxide ($SnO_2$) films were deposited on multiwall carbon nanotube buckypaper using a rf magnetron sputter process in a mixed oxygen/argon (1/9) gas environment. Conditions for the growth of $SnO_2$ thin films on multiwall carbon nanotube buckypaper by rf sputtering are: target composition $SnO_2$ (99.999 wt%); total system pressure 1 Pa; sputtering power (rf) 75, 100 and 125 W, respectively; $O_2//Ar$ (1/9) gas mixture. The surface morphology of the $SnO_2$ multiwall carbon nanotube composite films was investigated by scanning electron microscopy. The crystallographic structure of the sample was determined by X-ray diffraction. The electrochemical properties of $SnO_2$ multiwall carbon nanotube composite anodes were investigated by galvanostatic charge-discharge experiments.
Źródło:
Acta Physica Polonica A; 2013, 123, 2; 358-360
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Cyclic Performance Tests of Si/MWCNT Composite Lithium Ion Battery Anodes at Different Temperatures
Autorzy:
Tocoglu, U.
Cevher, O.
Akbulut, H.
Powiązania:
https://bibliotekanauki.pl/articles/1192560.pdf
Data publikacji:
2015-04
Wydawca:
Polska Akademia Nauk. Instytut Fizyki PAN
Tematy:
77.55.df
81.15.Cd
82.47.Aa
78.67.Sc
61.48.De
Opis:
In this study silicon-multi walled carbon nanotube (Si-MWCNT) lithium ion battery anodes were produced and their electrochemical galvanostatic charge/discharge tests were conducted at various (25°C, 35°C, 50°C) temperatures to determine the cyclic behaviors of anode at different temperatures. Anodes were produced via vacuum filtration and DC magnetron sputtering technique. Silicon was sputtered onto buckypapers to form composite structure of anodes. SEM analysis was conducted to determine morphology of buckypapers and Si-MWCNT composite anodes. Structural and phase analyses were conducted via X-ray diffraction and Raman Spectroscopy technique. CR2016 coin cells were assembled for electrochemical tests. Cyclic voltammetry test were carried out to determine the reversibility of reactions between anodes and reference electrode between 0.01-2.0 V potential window. Galvanostatic charge/discharge tests were performed to determine cycle performance of anodes at different temperatures.
Źródło:
Acta Physica Polonica A; 2015, 127, 4; 1059-1061
0587-4246
1898-794X
Pojawia się w:
Acta Physica Polonica A
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-10 z 10

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies