Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Konczakowska, A." wg kryterium: Autor


Wyświetlanie 1-2 z 2
Tytuł:
Application of infrared thermography to non-contact testing of varistors
Autorzy:
Galla, S.
Konczakowska, A.
Powiązania:
https://bibliotekanauki.pl/articles/220473.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
thermography
testing
varistors
Opis:
Testing of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors working in electronic devices as protective elements, on the basis of estimating temperature increments on varistor surfaces, registered by an infrared camera during surge resistance tests with standard voltage levels. To determine acceptable temperature increments on a tested varistor, preliminary testing was performed of P22Z1 (Littelfuse) and S07K14 (EPCOS) type varistors, working first at a constant load and presently during surge tests,. The thermographic test results were compared with measured varistor capacity values before and after tests. It was found that recording with thermography temperature increments greater than 6°C for both P22Z1 and S07K14 varistor types detects total or partial loss of varistor protective properties. The test results were confirmed by assessment of protective properties of varistors working in output circuits of low nominal voltage devices.
Źródło:
Metrology and Measurement Systems; 2013, 20, 4; 677-688
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena jakości wodorostów na podstawie pomiarów termowizyjnych
Application of infrared thermography to varistors quality evaluation
Autorzy:
Bobcow, M.
Galla, S.
Konczakowska, A.
Powiązania:
https://bibliotekanauki.pl/articles/266990.pdf
Data publikacji:
2015
Wydawca:
Politechnika Gdańska. Wydział Elektrotechniki i Automatyki
Tematy:
termografia
warystory
ocena jakości
infrared thermography
varistors
quality evaluation
Opis:
Zaproponowano zastosować temperaturę, mierzoną metodą termowizyjną, do indywidualnej oceny jakości warystorów. Badania przeprowadzono dla 20 warystorów niskonapięciowych. Wykonano pomiary parametrów elektrycznych i temperatury warystorów przed testami narażeniowymi i po 2 kolejnych cyklach narażeń. Testy narażeniowe zastosowano w celu pogorszenia jakości warystorów. Zaproponowano zasady klasyfikacji badanych warystorów do grup o wysokiej i niskiej jakości na podstawie pomiarów parametrów elektrycznych przed testami. Na podstawie porównania wyników pomiarów parametrów elektrycznych i temperatury wykonanych, przed i po testach narażeniowych, wytypowano temperaturę T warystora, mierzoną po 5 minutach samo-podgrzania, jako wartość umożliwiającą klasyfikację badanego warystora do grup jakościowych. Wartość temperatury T większa niż 40 0C wskazuje, że badany warystor jest niskiej jakości.
The use of thermography displacement (NDT - non-destructive tests) is proposed to assess the quality of individual varistor. Twenty low-voltage varistors were studied where electrical and thermal performance measurements were taken before the stress-tests (part I) and after two subsequent cycles of two-tier stress tests (part III and V, respectively). Stress-tests were used to obtain degradation of the tested varistors (part II and IV, respectively). The following electrical parameters were measured: electric resistance Rp , quality Q, dissipation factor D and leakage current Iupł. The scope of the thermographic study included measurements of the varistors’ temperature within 5 minutes after turning on the power (self-heating) and 5 minutes after turning off the power (cooling). A comparison study was conducted of the classification rules, where varistors were assigned to groups depending on their quality based on either the electrical parameters measured before the stress tests, or their temperature measurements. Varistor’s temperature T, measured after self-heating it up for 5 minutes, was selected as the borderline value on basis of which the selection to the different quality groups was conducted. The temperature T higher than 40 0C indicates that the test specimen is of average or poor quality and should not be used.
Źródło:
Zeszyty Naukowe Wydziału Elektrotechniki i Automatyki Politechniki Gdańskiej; 2015, 46; 21-24
1425-5766
2353-1290
Pojawia się w:
Zeszyty Naukowe Wydziału Elektrotechniki i Automatyki Politechniki Gdańskiej
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-2 z 2

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies