Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "prąd łożyskowy" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
Prądy łożyskowe i prąd uziomu w układach napędowych zasilanych z falowników PWM
Bearing currents and leakage current in PWM inverter drives
Autorzy:
Zientek, P.
Powiązania:
https://bibliotekanauki.pl/articles/1374757.pdf
Data publikacji:
2006
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
prąd łożyskowy
układ napędowy
falownik PWM
silniki elektryczne
Opis:
The paper presents analysis of forming of the induction motor bearing currents and leakage currents. In chapter 2 the causes at common-mode voltage and shaft voltage formation are described. That voltages are both the cause of EDM bearing currents forming. In chapter 3 are presented different types of parasitic phenomena caused by common-mode voltage. Internal capacitances of the induction motor is shown in Fig.5. Figure 8 shows EDM bearing currents formation. Leakage currents in induction motors supplied from PWM Inverter are presented in chapter 4. Chapter 5 describes methodes for limiting bearing currents in PWM drives.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2006, 74; 69-74
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Prady łożyskowe w układach napędowych z falownikami PWM
Bearing currents in PWM inverter-fed drives
Autorzy:
Kempski, A.
Smoleński, R.
Powiązania:
https://bibliotekanauki.pl/articles/1374764.pdf
Data publikacji:
2006
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
prąd łożyskowy
układ napędowy
falownik PWM
silniki elektryczne
Opis:
The application of high switching techniques improves the economic and technical parameters of induction motor drives. However, it has been discovered recently an adverse effect on a bearing assembly which is caused by destructive bearing currents EDM (Electrical Discharge Machining). Since the introduction of the IGBT technology there has been a documented increase in electrically induced bearing failures and shortening electrical life of bearings. In the paper it has been presented the statistical approach related to the distributions of EDM currents in drives with different filter configurations. Commonly used solutions for CM currents reducing are the line reactors and CM chokes. However, they increase risk of the appearance of EDM currents of higher amplitudes in shorter awaiting times. The CM transformer is a good choice for a simultaneous decreasing of the CM current and the risk of EDM currents. However, the best method of an elimination of bearing currents is a cancellation of its source - common mode voltage - at the output of the inverter. In a paper it has been presented so-called sinusoidal filter that assures nearly zero common voltage at the filter output, strongly damps common and differential EMI and eliminate bearing currents.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2006, 74; 75-80
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Metody eliminacji prądów łośyskowych i prądu uziomu w układach napędowych zasilanych z falowników PWM
The method of elimination bearing currents and leakage current in PWM inverter drives
Autorzy:
Zientek, P.
Niestrój, R.
Powiązania:
https://bibliotekanauki.pl/articles/1373847.pdf
Data publikacji:
2009
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Napędów i Maszyn Elektrycznych Komel
Tematy:
prąd łożyskowy
układ napędowy
falownik PWM
silnik elektryczny
zjawiska pasożytnicze
Opis:
In the paper are discussed different kinds of parasitic phenomena occurring in PWM inverter driven induction motors. In the article describes methodes for limiting bearing currents and common-mode current in PWM drives. The paper also presents results of experimental researches. Conclusions drawn from laboratory researches are presented in chapter 7.
Źródło:
Maszyny Elektryczne: zeszyty problemowe; 2009, 82; 193-202
0239-3646
2084-5618
Pojawia się w:
Maszyny Elektryczne: zeszyty problemowe
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies