Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "toluene" wg kryterium: Temat


Wyświetlanie 1-11 z 11
Tytuł:
Toluen
Toluene
Autorzy:
Jakubowski, M.
Powiązania:
https://bibliotekanauki.pl/articles/137571.pdf
Data publikacji:
2007
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
toluen
narażenie przemysłowe
NDS
toluene
occupational exposure
OEL
Opis:
Toluen ma wszechstronne zastosowanie jako surowiec w procesie produkcji gumy, żywic, detergentów, barwników, leków, trinitrotoluenu, kwasu benzoesowego i diizocyanianu toluenu. Toluen jest składnikiem wielu takich produktów rynkowych, jak: farby, szelak, inhibitory korozji, rozcieńczalniki oraz środki czyszczące i sanitarne zawierające rozpuszczalniki organiczne. Narażenie zawodowe na toluen może występować na etapie produkcji, wytwarzania, konfekcjonowania i przechowywania półproduktów i produktów zawierających toluen, jak również ich stosowania, np. w trakcie malowania farbami i lakierami czy oczyszczania powierzchni. Toluen może wchłaniać się do organizmu przez płuca, z przewodu pokarmowego i przez skórę. Retencja par toluenu w płucach u ludzi wynosi około 60 ÷ 80%. Szybkość wchłaniania toluenu przez skórę wynosi w przypadku kontaktu 0,69 mg/cm2/h. Główną drogą przemiany toluenu u ludzi jest utlenianie reszty metylowej do grupy karboksylowej z utworzeniem kwasu benzoesowego, który następnie ulega sprzęganiu z glutationem z utworzeniem kwasu hipurowego. Półokres wydalania kwasu hipurowego z moczem po narażeniu inhalacyjnym wynosi około 3,5 h. Efekty krytyczne działania toluenu obejmują działanie drażniące na oczy, wpływ na reprodukcję, działanie oto toksyczne i neurotoksyczne. Wartość NOAEL dla działania neurotoksycznego toluenu (wykonywanie testów psychometrycznych) ustalono na poziomie około 375 mg/m3. Spontaniczne poronienia występowały u kobiet narażonych zawodowo na toluen o stężeniach rzędu 170 ÷ 550 mg/m3 (średnio 300 mg/m3). Narażenie na toluen powoduje podrażnienie układu oddechowego, oczu i ból głowy. Stężenie 150 mg/m3 toluenu przyjęto za wartość NOAEL dla tego typu skutków działania, a stężenie 375 mg/m3 za wartość LOAEL. Przyjmując za skutek krytyczny działanie drażniące, zaproponowano wartość NDS toluenu równą 100 mg/m3. Pozostawiono również oznakowanie normatywu literami „Sk” (substancja wchłania się przez skórę) i literami „Ft” (substancja działa toksycznie na płód). Ze względu na działanie drażniące związku ustalono wartość NDSCh toluenu równą 200 mg/m3. Oznaczanie stężenia kwasu hipurowego w moczu zastąpiono oznaczaniem stężenia o-krezolu. Wartość DSB (dopuszczalne stężenie w materiale biologicznym) ustalono na poziomie 0,5 mg o-krezolu/g kreatyniny w próbkach moczu pobranych po zakończeniu zmiany roboczej.
Toluene is a clear, colorless liquid with a distinctive smell. The largest source of toluene release is during the production, transport and use of gasoline, which contains 5 ÷ 7% toluene by weight. Toluene is used in making paints, paint thinners, lacquers and adhesives. Absorption of toluene results mainly from inhalation of its vapor. In human studies retention of toluene in the lungs has been estimated by different authors to be 60 ÷ 80%. Significant amounts may also be absorbed through the skin if there is contact with the liquid form. The rate of absorption through the skin amounts to about 0.69 mg/cm2/h. Following absorption, toluene is rapidly distributed, with the highest levels observed in adipose tissue followed by bone marrow, adrenals, kidneys, liver, brain and blood. A mean toluene half-life of toluene in blood amount to 4.5 h and to 3.8 h in alveolar air. Approximately 20% of the absorbed toluene is excreted unchanged in the expired air. A minute amount is excreted in urine. The reminder is oxidized by transformation of the methyl radical into the carboxyl radical, which is mainly conjugated with glycine to produce hippuric acis. Less than 1% of the dose is hydroxylated to cresols. Hippuric acid is excreted in urine with a biological half-life of 3.5 h. Adverse effects on the nervous system and respiratory tract irritation are the critical effects from inhalation exposure to toluene. Experimental exposure of human volunteers to toluene at about 375 mg/m3 did not produce statistically significant differences in the results of tests measuring psychometric performance and subjective evaluations of well-being when compared to controls (NOAEL). Spontaneous abortions were observed as result of occupational exposure to toluene in concentrations of 170 ÷ 550 mg/m3. Irritation of the nose and throat was reported in printers exposed to 375 mg/m3 of toluene for 6.5 h and in volunteers exposed to the same concentration of toluene for 6 h (LOAEL). The proposed occupational exposure limits OEL-TWA of 100 mg/m3 and OEL-STEL of 200 mg/m3 are based on the LOAEL of 375 mg/m3 for irritative properties of toluene. As toluene is absorbed through the skin and is potentially fetotoxic the “Sk” and “Ft” symbols should denote this compound. A BEI value of 0.5 mg of o-cresol in urine samples collected at the end of the workshift has been proposed.
Źródło:
Podstawy i Metody Oceny Środowiska Pracy; 2007, 3 (53); 131-158
1231-868X
Pojawia się w:
Podstawy i Metody Oceny Środowiska Pracy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Degradation of toluene using UV/hydrogen peroxide process
Autorzy:
Cai, Shaokang
Sun, Yue
Gao, Canzhu
Li, Pengfei
Cheng, Zhongfa
Powiązania:
https://bibliotekanauki.pl/articles/2032937.pdf
Data publikacji:
2021
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
AOP
toluene
hydrogen peroxide
spectrofotometer
toluen
nadtlenek wodoru
spektrofotometria
Opis:
Toluene in wastewater is volatile and difficult to degrade, and the longer it stays in the water, the higher is the risk. An advanced oxidation process (AOPs) has been used to degrade toluene rapidly and efficiently in wastewater by using ultraviolet light and hydrogen peroxide. Toluene in solution (initial concentration – 180 mg/dm3) with hydrogen peroxide (H2O2 dose – 2022 mg/dm3) was almost decomposed within 150 min. pH as well as the presence of various ions in waste water did not affect the degradation process. However, under strongly acidic conditions (pH less than 3), the chloride ions reduced the degradation efficiency of toluene. Based on the UV spectrophotometer and GC-MS analyses, the degradation pathways were observed: first, the methyl group was oxidized leading to the generation of benzoic acid, the benzene ring was subsequently opened by the action of hydroxyl radical, followed by the gradual decomposition of the intermediate products into small molecules such as water and carbon dioxide.
Źródło:
Environment Protection Engineering; 2021, 47, 1; 5-15
0324-8828
Pojawia się w:
Environment Protection Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Model of aromatic hydrocarbons transport in porous ground media
Model transportu węglowodorów ropopochodnych w gruncie porowatym
Autorzy:
Gawdzik, J.
Powiązania:
https://bibliotekanauki.pl/articles/127374.pdf
Data publikacji:
2010
Wydawca:
Towarzystwo Chemii i Inżynierii Ekologicznej
Tematy:
hydrocarbons
benzene
toluene
ethylbenzene
transport in soil
węglowodory ropopochodne
benzen
toluen
etylobenzen
transport w glebie
Opis:
Dispersion model of NAPL hydrocarbons’ transport in porous media has been presented. Mathematical model allows to estimate whether the menace of ground water can occur as a result of hydrocarbons’ transport through the soil. The convection in mass transport is considered in the general equation due to the higher velocity of propagation in vertical direction. The introduction of the equation of biosorption link allows to take into account microorganisms’ influence on impurities concentration, especially on heavy oils derived compounds. The research conducted on a filter model was the first step to verify the dispersion model of petroleum derived substances. Dispersion coefficient was assessed for benzene, toluene and ethylbenzene.
W pracy wprowadzono dyspersyjno-konwekcyjny model migracji węglowodorów ropopochodnych w gruntach. Proponowany model jest próbą znalezienia mechanizmu propagacji węglowodorów przez ośrodek porowaty i pozwala przewidzieć, na ile migracja benzenu, toluenu i etylobenzenu jest w stanie zagrozić zwierciadłu wód podziemnych. Uwzględnienie konwekcji w równaniu transportu masy podyktowane jest zwiększoną szybkością migracji węglowodorów w kierunku pionowym. Wprowadzenie równania biosorpcji pozwala uwzględnić wpływ mikroorganizmów na zmianę stężenia, głównie ciężkich węglowodorów ropopochodnych w gruncie. Poprawność modelu zweryfikowano doświadczalnie na modelu filtra gruntowego poprzez wyznaczenie współczynnika dyspersji wzdłużnej dla benzenu, toluenu i etylobenzenu.
Źródło:
Proceedings of ECOpole; 2010, 4, 1; 29-35
1898-617X
2084-4557
Pojawia się w:
Proceedings of ECOpole
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Laboratoryjny biofiltr strużkowy do oczyszczania powietrza z lotnych związków organicznych o charakterze odorowym
Laboratory biotrickling filter for the removal of odorous volatile compounds from air
Autorzy:
Rybarczyk, Piotr
Gospodarek, Milena
Szulczyński, Bartosz
Gębicki, Jacek
Namieśnik, Jacek
Powiązania:
https://bibliotekanauki.pl/articles/1366418.pdf
Data publikacji:
2019
Wydawca:
Centralny Ośrodek Badawczo-Rozwojowy Aparatury Badawczej i Dydaktycznej, COBRABiD
Tematy:
biofiltracja
biofiltr strużkowy
złoże zraszane
toluen
stopień usunięcia
biofiltration
biotrickling filter
trickled bed
toluene
removal ratio
Opis:
W pracy przedstawiono wyniki badań doświadczalnych procesu dezodoryzacji powietrza zanieczyszczonego parami toluenu w biofiltrze ze złożem zraszanym (tj. w biofiltrze strużkowym). Zaproponowano układ badawczy do procesu biofiltracji, oparty na bioreaktorze dwusekcyjnym, wypełnionym ceramicznymi pierścieniami Raschiga. Złoże biofiltra zaszczepiono drobnoustrojami z rodzaju Candida. Jako ciecz zraszającą stosowano wodny roztwór soli mineralnych. Zbadano i porównano skuteczność usuwania toluenu z mieszaniny z powietrzem, stosując ciecz zraszającą bez dodatku i z dodatkiem dodecylosiarczanu sodowego. Stwierdzono, że dodatek związku powierzchniowo czynnego powoduje wzrost stopnia usunięcia toluenu w procesie biofiltracji. Wskazano, że proponowane stanowisko może być z powodzeniem stosowane podczas laboratoryjnych badań procesu biofiltracji, zapewniając stabilność pracy układu oraz ograniczenie problemów technicznych związanych z nadmiernym wzrostem biomasy w złożu biofiltra.
The paper presents the results of experimental investigations of the deodorization process of air contaminated with toluene vapors in a trickled-bed biofilter (i.e. biotrickling filter). A laboratory set-up for biofiltration process was proposed, based on a two-section bioreactor filled with Raschig ceramic rings. The biofilter bed was inoculated with microorganisms from the Candida species. Aqueous solution of mineral salts was used as the trickling liquid. The effectiveness of toluene removal from its mixture with air was investigated and compared using a trickling liquid without addition and with the addition of sodium dodecyl sulphate. It has been found that the addition of a surfactant increases the degree of toluene removal in the biofiltration process. It was pointed out that the proposed set-up can be successfully applied during laboratory investigations of the biofiltration process, ensuring system stability and reducing technical problems related to excessive biomass growth in the biofilter bed.
Źródło:
Aparatura Badawcza i Dydaktyczna; 2019, 24, 1; 24-30
2392-1765
Pojawia się w:
Aparatura Badawcza i Dydaktyczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Activated carbon adsorption behaviour of toluene at various temperatures and relative humidity
Autorzy:
Görgülü, Adnan
Yağli, Hüseyin
Koç, Yildiz
Koç, Ali
Baltacioğlu, Ertuğrul
Powiązania:
https://bibliotekanauki.pl/articles/207947.pdf
Data publikacji:
2019
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
activated carbon
toluene
diffusion
relative humidity
temperature
environmental pollution
węgiel aktywny
toluen
dyfuzja
wilgotność względna
temperatura
zanieczyszczenie środowiska
Opis:
Filtration plays a major role in managing the rapid increase of environmental pollution and deterioration of atmospheric air quality. One of the most damaging noxious gases in the atmosphere is toluene, which is a common gas that appears in crude oil and is used in various production processes. The adsorption behaviour of activated carbon was examined in dependence of the concentration, temperature and relative humidity. The results showed that increasing air temperature decreased the time to reach the maximum saturation ratio, which occurred due to the increasing pore diffusion coefficient and pore diffusion rate.
Źródło:
Environment Protection Engineering; 2019, 45, 1; 111-126
0324-8828
Pojawia się w:
Environment Protection Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Destrukcyjne utlenianie domieszki toluenu w powietrzu w reaktorze koronowym i reaktorze hybrydowym, koronowo-katalitycznym
Destructive oxidation of toluene admixture in air in a corona and hybrid corona-catalytic reactors
Autorzy:
Parus, W.
Paterkowski, W.
Straszko, J.
Powiązania:
https://bibliotekanauki.pl/articles/2072399.pdf
Data publikacji:
2013
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
reaktor hybrydowy koronowo-katalityczny
spalanie
toluen
katalizator tlenkowy
hybrid corona-catalytic reactor combustion
toluene
metal oxides catalyst
Opis:
Przedstawiono wyniki badań destrukcyjnego utleniania domieszki toluenu w powietrzu w reaktorze koronowym i reaktorze hybrydowym, koronowo - katalitycznym. Stosowano zasilacz i reaktory własnej konstrukcji oraz katalizator (4 g) o składzie 45% mas. Mn02 + 30% mas. Fe203 +25 % mas. CuO, otrzymany w laboratorium autorów. Pomiary wykonano przy różnych parametrach pracy zasilacza. Napięcie zasilania zmieniano w zakresie 13,2÷13,6 kV a częstotliwość prądu w przedziale 0 ÷ 1,8 kHz. Stężenia toluenu zmieniano w zakresie 0,78+7,20 g/m3, a przepływ gazu w granicach 520÷1475 dm3/h. Ustalono, że zależnie od parametrów zasilania, objętościowego przepływu gazów i temperatury gazów uzyskuje się w reaktorze koronowym stopnie destrukcji toluenu do produktów nietoksycznych (C02 i H2O) w zakresie 0,178÷0,755, a w reaktorze hybrydowym koronowo-katalitycznym w granicach 0,29÷0,958. Stwierdzono, że wzrost częstotliwości pracy generatora powoduje zwiększenie stopnia przemiany w obu typach reaktorów. Natomiast zwiększenie objętościowego przepływu gazów skutkuje obniżeniem stopnia przemiany tej domieszki.
Research results dealing with the destructive oxidation of toluene admixture in air using a corona and hybrid corona - catalytic reactors are presented. A generator and reactors of authors’ own design and catalyst (4 g) of composition 45 wt. % Mn02, 30 wt. % Fe203 and 25 wt. % CuO obtained in authors own laboratory were used. The measurements were performed for different parameters of generator operation. A generator voltage varied in a range from 13.2 to 13.6 kV, whereas current frequency in a range of 0.4÷1.8 kHz. The toluene concentration was changed in a range 0.78÷7.20 g/m3 and gas flow rate within a range 520÷1475 Ndm3/ h. It was established that depending on generator parameters, volume gas flow rate and gas temperature, the destruction degree of toluene to non-toxic products (C02 i H2O) achieved for the corona and hybrid corona - catalytic reactors were in a range of 0.178÷0.755 and 0.29÷0.958, respectively. It was found that the increase of generator operational frequency caused the enhancement of toluene conversion degree for both types of reactors. On the other hand, the increase of volume gas flow rate resulted in the decrease of toluene conversion degree.
Źródło:
Inżynieria i Aparatura Chemiczna; 2013, 4; 361--363
0368-0827
Pojawia się w:
Inżynieria i Aparatura Chemiczna
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Aktywność katalizatorów perowskitowych z dodatkiem platyny w utlenianiu organicznych zanieczyszczeń powietrza
Activity of perovskite-based platinum doped catalysts in oxidation of organic air pollutants
Autorzy:
Musialik-Piotrowska, A.
Powiązania:
https://bibliotekanauki.pl/articles/237099.pdf
Data publikacji:
2011
Wydawca:
Polskie Zrzeszenie Inżynierów i Techników Sanitarnych
Tematy:
organiczne zanieczyszczenia powietrza
toluen
aceton
octan etylu
katalizator
perowskit
platyna
organic air pollutants
toluene
acetone
ethyl acetate
catalyst
perovskite
platinum
Opis:
Katalizatory tlenkowe oparte na tlenkach złożonych o strukturze perowskitu zazwyczaj wykazują wysoką aktywność w utlenianiu związków tlenopochodnych, natomiast zwykle są mało aktywne w utlenianiu węglowodorów, szczególnie aromatycznych. Do badań wykonano katalizatory na bazie perowskitu (LaMnO3), z dodatkiem platyny wprowadzonej do fazy aktywnej, na monolitycznym nośniku metalowym z warstwą pośrednią gamma-Al2O3. Przebadano je w utlenianiu toluenu oraz acetonu i octanu etylu, spalanych indywidualnie i w mieszaninach dwuskładnikowych - węglowodór i pochodna tlenowa. Wykazano, że utlenianie samego toluenu zachodziło do produktów końcowych - CO2 i H2O, natomiast związki tlenowe utleniały się poprzez produkty pośrednie - aldehyd octowy - w spalaniu obu związków oraz etanol - podczas spalania octanu etylu. W przypadku wszystkich katalizatorów niewielki wzajemny wpływ na spalanie każdego ze związków zaobserwowano spalając mieszaninę toluen-aceton, wyraźnie większy w przypadku mieszaniny toluen-octan etylu. Spalanie toluenu w mieszaninach na mniej aktywnych katalizatorach przebiegało poprzez benzen. W obecności obu katalizatorów dotowanych platyną, podczas spalania mieszanin stężenie aldehydu octowego zmalało, prawdopodobnie wskutek lokalnego wzrostu temperatury na platynie w wyniku spalenia toluenu. Najwyższą aktywność wykazał katalizator z dodatkiem platyny wstępnie naniesionej na gamma-Al2O3, o ogólnej zawartości czynnika aktywnego 20% mas. Stwierdzono, że minimalna zawartość czynnika aktywnego w przypadku katalizatorów tlenkowych nie powinna być mniejsza niż 15% mas.
Metal oxide perovskite-type catalysts usually show high activity for oxidizing oxy-derivative compounds, but they are much less active in the oxidation of hydrocarbons, particularly aromatics. For the purpose of the study, LaMnO3-based catalysts, with platinum incorporated into the active phase, were prepared on monolithic metallic supports washcoated with gamma-Al2O3. The catalysts were tested in the oxidation of toluene, as well as acetone and ethyl acetate, which were combusted separately or in two-component mixtures - hydrocarbon and oxy-derivative. It has been demonstrated that when toluene alone was oxidized, the reaction ran to final products - CO2 and H2O, while oxygen compounds were oxidized via intermediate products - acetaldehyde during combustion of both compounds, and ethanol during combustion of ethyl acetate. With all the catalysts tested, the "mixture effect" of each component was insignificant during oxidation of the toluene-acetone mixture, and noticeably stronger during combustion of the toluene-ethyl acetate mixture. The combustion of toluene in mixtures over catalysts of lower activity occurred via benzene. In the presence of Pt-doped catalysts, the concentration of acetaldehyde during combustion of mixtures decreased, which was probably due to a local rise in temperature on the Pt active sites as a result of toluene oxidation. The highest activity was that of the catalyst where platinum was deposited onto gamma-Al2O3, and the total content of the active phase amounted to 20 wt. %. It has been found that in the case of metal oxide catalysts the minimal content of the active phase can not be lower than 15 wt. %.
Źródło:
Ochrona Środowiska; 2011, 33, 1; 19-24
1230-6169
Pojawia się w:
Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Benzen, cykloheksan, etylobenzen, n-heksan, metylocykloheksan, toluen – metoda oznaczania
Benzene cyclohexane, ethylbenzene, n-hexane, methylcyclohexane, toluene -a determination method
Autorzy:
Domański, W.
Powiązania:
https://bibliotekanauki.pl/articles/137771.pdf
Data publikacji:
2011
Wydawca:
Centralny Instytut Ochrony Pracy
Tematy:
benzen
cykloheksan
etylobenzen
n-heksan
metylocykloheksan
toluen
metoda chromatografii gazowej
benzene
cyclohexane
ethylbenzene
n-hexane
methylcyclohexane
toluene
gas chromatography metod
workplace air
Opis:
Metoda polega na adsorpcji na węglu aktywnym zawartych w powietrzu par: benzenu, cykloheksanu, etylobenzenu, n-heksanu, metylocykloheksanu i toluenu, a następnie desorpcji disiarczkiem węgla oraz analizie chromatograficznej roztworu uzyskanego w wyniku desorpcji.Metodę stosuje się do oznaczania wymienionych węglowodorów w powietrzu na stanowiskach pracy podczas przeprowadzania kontroli warunków sanitarnych. Oznaczalność metody wynosi: 0,15 mg benzenu, 7,5 mg cykloheksanu, 5 mg etylobenzenu, 3,75 mg n-heksanu, 25 mg metylocykloheksanu i 5 mg toluen w 1 m3 powietrza.
This method is based on the adsorption of benzene cyclohexane, ethylbenzene, n-hexane, methy-locyclohexane and toluene vapors on active charcoal, desorption with carbon disulphide and determination with gas chromatography with an FID detector. The determination limit of this method in the air sample is 0.15 mg/m3 for benzene, 7.5 mg/m3 for cyclohexane, 5 mg/m3 for ethylbenzene, 3.75 mg/m3 for n-hexane, 25 mg/m3 for methylcyclohexane and 5 mg/m3 for toluene.
Źródło:
Podstawy i Metody Oceny Środowiska Pracy; 2011, 1 (67); 35-44
1231-868X
Pojawia się w:
Podstawy i Metody Oceny Środowiska Pracy
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Catalytic decomposition of toluene over La1-xSr xMnO3/palygorskite synthesized catalysts
Autorzy:
Song, L.
Chen, T.
Chen, D.
Chen, Y.
Xie, J.
Liu, H.
Powiązania:
https://bibliotekanauki.pl/articles/207996.pdf
Data publikacji:
2013
Wydawca:
Politechnika Wrocławska. Oficyna Wydawnicza Politechniki Wrocławskiej
Tematy:
catalysts
manganese
manganese oxide
toluene
transmission electron microscopy
X ray diffraction
Palygorskite
katalizatory
mangan
tlenek manganu
toluen
transmisyjna mikroskopia elektronowa
dyfrakcja promieniowania rentgenowskiego
Opis:
Palygorskite (PG) supported La1-xSrxMnO3 catalysts were fabricated by copreripitation. The catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area (SSA) and H2 temperature programmed reduction (H 2-TPR). Catalytic activity for VOCs was examined by using toluene as a model compound. The results show that the surface area as well as mechanical strength of catalysts increase substantially after catalysts loaded in PG. XRD patterns show that after calcination at 700 0C, PG as a support in 9% LaMn03/PG and 9% La0.7Sr0.3MnO3/PG was transformed into amorphous phase and the morphology was not destroyed. It was well established that the main reductive components are factually Mn(III) or Mn(IV) oxides in catalysts based on the results of TPR. It was also found that Mn(IV) increases while Mn(III) reduces responding with the increasing amount of Sr. Toluene conversion rate of as-preparedμ% La1-xSr xMnO3/PG increases with the increasing values of x and μ when x=0-0.3 and μ = 3-9%. Toluene can be converted completely at 285 0C by 9% La0.7Sr0.3MnO3/PG catalyst while no significant change was observed after addition on the doping and loading amount of Sr. During a 100 h stability experiment of 9% La 0.7Sr0.3MnO3/PG catalyst, toluene removal was found to be above 95%.
Źródło:
Environment Protection Engineering; 2013, 39, 3; 31-42
0324-8828
Pojawia się w:
Environment Protection Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the efficiency of the three-way catalytic converter of a spark ignition engine of the chosen aromatic hydrocarbons removing
Autorzy:
Skrętowicz, M.
Woźniak, J.
Wróbel, R.
Powiązania:
https://bibliotekanauki.pl/articles/133224.pdf
Data publikacji:
2017
Wydawca:
Polskie Towarzystwo Naukowe Silników Spalinowych
Tematy:
hydrocarbons
three-way catalytic converter
TWC
exhaust
benzene
toluene
xylenes
BTX
spark ignition engines
węglowodory
reaktor katalityczny trójfunkcyjny
spaliny
benzen
toluen
ksylen
silnik z zapłonem iskrowym
Opis:
In the paper the results of measurement of the most popular aromatic hydrocarbons (benzene, toluene and xylenes) in the exhaust of spark ignition engine before and after three-way catalytic reactor were presented. The investigations have been conducted at fixed rotational speed, 2500 rpm and at a few different values of torque in range 0 – 80 Nm, every 10 Nm. Based on obtained results, the calculations of catalytic reactor efficiency in removing analysed components have been made. The measurements showed high efficiency of the catalytic converter in reduction of that pollutants in exhaust gases.
Źródło:
Combustion Engines; 2017, 56, 2; 83-86
2300-9896
2658-1442
Pojawia się w:
Combustion Engines
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Ocena możliwości zastosowania procesu zestalania chemicznego do unieszkodliwiania gleby zanieczyszczonej toluenem
Assessment of applicability of chemical solidification process to treat soils contaminated with toluene
Autorzy:
Banaszkiewicz, K. P.
Pasiecznik, I.
Powiązania:
https://bibliotekanauki.pl/articles/236872.pdf
Data publikacji:
2017
Wydawca:
Polskie Zrzeszenie Inżynierów i Techników Sanitarnych
Tematy:
volatile organic compounds (VOCs)
toluene
cement
diatomaceous earth
textile fibers
rubber granulate
solidification
adsorption
immobilization
compressive strength
capillary water absorption
lotne związki organiczne
toluen
ziemia okrzemkowa
kord tekstylny
granulat gumy
zestalanie
adsorpcja
kapsułacja
wytrzymałość mechaniczna
nasiąkliwość wodą
Opis:
Chemical solidification is an established technology used in treatment of inorganic wastes contaminated mainly with trace metals (Cd, Cu, Zn, Ni, Pb). During this process, metal ions are chemically bound to hydration products of cement. In case of organic compounds, particularly volatile organic compounds (VOCs), the solidification technology has some limitations. Volatilization of VOCs during mechanical mixing of individual components of the binding mixture is a major problem. With this in mind, applicability of the technology for treatment of sandy soil contaminated with toluene was assessed in laboratory tests. Three binding (solidifying) Portland cementbased (CEM I 42.5 R) formulations, additionally supplemented with diatomaceous earth and textile fibers of high waste-rubber content were tested for soil solidification. These additional components acted as adsorbents to reduce the toluene evaporation. In the course of treatment, emission of all the gaseous contaminants was monitored. Influence of the binding (solidifying) mixture composition on toluene emission was evaluated based on the momentary toluene concentrations monitored above the surface of the reactive mixture using flame-ionization detector. The research results confirmed beneficial effect of hermetization of the contaminated soil using Portland cement. Introduction of cement equivalent to 50% of the soil weight resulted in the reduction of total toluene emission by over 26%. The cement-based mixtures containing diatomaceous earth or textile fibers gave higher results (27–45%).
Stabilizacja/zestalanie jest powszechnie stosowanym procesem do unieszkodliwiania odpadów mineralnych, głównie zanieczyszczonych metalami śladowymi. W procesie tym jony metali są chemicznie wiązane z produktami hydratacji cementu. W przypadku zanieczyszczeń organicznych, w szczególności lotnych związków organicznych, technologia stabilizacji/zestalania ma pewne ograniczenia. Największy problem stanowi uwalnianie lotnych związków organicznych w trakcie mechanicznego mieszania poszczególnych składników mieszaniny wiążącej. Mając to na uwadze, w testach laboratoryjnych oceniono możliwość zastosowania tej technologii do unieszkodliwiania gleby piaszczystej zanieczyszczonej toluenem. Do stabilizacji/zestalania takiej gleby zastosowano trzy mieszaniny wiążące (zestalające) na bazie cementu portlandzkiego (CEM I 42,5 R), zawierające ponadto ziemię okrzemkową lub kord tekstylny z dużą ilości odpadowej gumy z opon. Te dodatkowe składniki pełniły rolę adsorbentów ograniczających emisję toluenu. W trakcie procesu prowadzono monitoring emitowanych zanieczyszczeń gazowych. Ocenę wpływu składu mieszaniny wiążącej (zestalającej) na emisję toluenu przeprowadzono na podstawie analizy stężeń chwilowych C7H8 zarejestrowanych detektorem płomieniowo-jonizacyjnym nad powierzchnią mieszaniny reakcyjnej. Wyniki badań potwierdziły korzystny wpływ hermetyzacji zanieczyszczonej gleby z użyciem cementu portlandzkiego. Zastosowanie cementu w ilości 50% masy gleby zmniejszyło całkowitą emisję toluenu o ponad 26%. Podobne efekty uzyskano stosując cement z dodatkiem ziemi okrzemkowej lub kordu tekstylnego.
Źródło:
Ochrona Środowiska; 2017, 39, 3; 41-46
1230-6169
Pojawia się w:
Ochrona Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-11 z 11

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies