Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Rudawska, Anna Rudawska" wg kryterium: Autor


Wyświetlanie 1-3 z 3
Tytuł:
Influence of Adhesive Compound Viscosity on the Strength Properties of 1.0503 Steel Sheets Adhesive Joints
Autorzy:
Miturska-Barańska, Izabela
Rudawska, Anna
Powiązania:
https://bibliotekanauki.pl/articles/2180221.pdf
Data publikacji:
2022
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
adhesive joints
carbon steel
shear strength
epoxy adhesives
viscosity
Opis:
The presented study concerned the comparison of the adhesive joints strengths of 1.0503 carbon steel sheets of higher quality, which were made using adhesive compounds characterized by different viscosity index of the components. Three types of commercial epoxy resins were used: Epidian 5, Epidian 53 and Epidian 57, as well as two types of curing agents: polyamide (PAC) and amine (Z-1). The surfaces of the test specimens were subjected to a pre-treatment operation in the process of a mechanical machining with an abrasive coated tool of P320 gradation. The surface roughness measurements were carried out as a control. The single-lap adhesive joints were the subject of the strength testing. The strength tests carried out on a Zwick/Roell Z150 testing machine concerned the comparison of the strength of the adhesive joints loaded in shear. Statistical analysis was performed on the results obtained. It was observed, among others, that the adhesive joints prepared with the epoxy adhesive compounds containing the polyamide curing agent showed much higher the shear strength than the adhesive joints made with the epoxy adhesive compounds containing the amine curing agent. Moreover, the use of the polyamide curing agent in the adhesive compounds with the epoxy resins resulted in formation of a more elastic adhesive layer, for which higher elongation was observed than in the case of the epoxy compound with the amine curing agent.
Źródło:
Advances in Science and Technology. Research Journal; 2022, 16, 2; 196-205
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Technological Factors on the Strength of Adhesive Joints of Steel Sheets
Autorzy:
Doluk, Elżbieta
Rudawska, Anna
Brunella, Valentina
Powiązania:
https://bibliotekanauki.pl/articles/102066.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
adhesive joint
shear strength
surface roughness
połączenie klejowe
wytrzymałość na ścinanie
chropowatość powierzchni
Opis:
The paper evaluates the effect of the surface treatment on the strength of the single‑lap adhesive joints made of the C45 steel. The samples were joined using an adhesive composition consisting of Epidian 57 epoxy resin and PAC curing agent. The study also used Greinplast mosaic plaster with a grain size of 1.0–1.6 mm as coating. The experiment was carried out for 3 variants of joints: sheet/sheet, sheet+plaster/sheet+plaster, sheet/sheet+plaster. Each variant was divided into 3 methods of surface treatment. The strength tests were carried out on the Zwick/Roell Z150 testing machine. The roughness parameters of the surface’s samples were measured using a HOMMEL TESTER T1000 profilometer.
Źródło:
Advances in Science and Technology. Research Journal; 2020, 14, 1; 107-115
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of overlap length on the strength of adhesive joints of steel sheets
Wpływ długości zakładki na wytrzymałość połączeń klejowych blach stalowych
Autorzy:
Doluk, Elżbieta
Rudawska, Anna
Miturska-Barańska, Izabela
Ogrodniczek, Jacek
Powiązania:
https://bibliotekanauki.pl/articles/31232904.pdf
Data publikacji:
2022
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
adhesive joint
shear strength
elongation
overlap length
połączenie klejowe
wytrzymałość na ścinanie
wydłużenie
długość zakładki
Opis:
The study evaluates the shear strength of the single-lap adhesive joints made of C45 carbon steel. The influence of the overlap length on the shear strength of the adhesive joint was tested. The elongation of the samples was also tested. Before the bonding process, the samples were treated with P180 abrasive paper and degreased. The adhesive joints were made using the Epidian 53/Z1/100:10 adhesive composition. The strength tests were carried out on a Zwick/Roell Z150 testing machine. The maximum value of the shear strength was obtained for the lap Lz1 = 13 mm and the minimum for Lz4 = 19 mm.
W pracy dokonano oceny wpływu długości zakładki na wytrzymałość na ścinanie jednozakładkowych połączeń klejonych wykonanych ze stali węglowej C45. Podczas eksperymentu zbadano także wydłużenie próbek. Przed rozpoczęciem procesu klejenia próbki zostały obrobione papierem ściernym P180 i odtłuszczone. Połączenia klejowe wykonano przy użyciu kompozycji klejowej Epidian 53/Z1/100:10. Badania wytrzymałościowe przeprowadzono na maszynie wytrzymałościowej Zwick/Roell Z150. Maksymalną wartość wytrzymałości na ścinanie uzyskano dla długości zakładki Lz1 = 13 mm, a minimalną dla Lz4 = 19 mm.
Źródło:
Technologia i Automatyzacja Montażu; 2022, 4; 3-6
2450-8217
Pojawia się w:
Technologia i Automatyzacja Montażu
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies