Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "plane" wg kryterium: Temat


Wyświetlanie 1-5 z 5
Tytuł:
A Study on Modelling the Plane Strain Behaviour of Sand and its Stability
Autorzy:
Sawicki, A.
Sławińska, J.
Powiązania:
https://bibliotekanauki.pl/articles/241244.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Instytut Budownictwa Wodnego PAN
Tematy:
sand deformations
liquefaction
instability
plane strain
Opis:
The plane strain behaviour of sand is studied using, previously proposed, incremental model describing its pre-failure deformations. Original model has been formulated for the tri-axial configuration, and then generalized for 3D conditions. This 3D model was subsequently adapted to study deformations of sand in the plane strain conditions, in the x1, x3 plane. There are three unknowns in such a configuration, namely the principal strains ε1 , ε3 and the principal stress σ2. Respective equations were derived, and then applied to study deformations of sand for chosen stress paths. The governing incremental equations were integrated numerically, and it was shown, for some loading paths, that σ2 depends linearly on the other principal stresses, so introduction of apparent Poisson's ratio is justified, as a kind of approximation. Subsequent analysis of deformations of sand was performed using this concept, as well as using full system of governing equations.
Źródło:
Archives of Hydro-Engineering and Environmental Mechanics; 2012, 59, 3-4; 85-100
1231-3726
Pojawia się w:
Archives of Hydro-Engineering and Environmental Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A generalized upper bound solution for extrusion of bi-metallic rectangular cross-section bars through dies of any shape
Uogólnione rozwiązanie ograniczenia górnego problemu wytłaczania bimetalowych belek o przekroju prostokątnym za pomocą tłoczników o dowolnym kształcie
Autorzy:
Haghighat, H.
Amjadian, P.
Powiązania:
https://bibliotekanauki.pl/articles/279195.pdf
Data publikacji:
2013
Wydawca:
Polskie Towarzystwo Mechaniki Teoretycznej i Stosowanej
Tematy:
extrusion
bimetal
plane strain
upper bound method
FEM
Opis:
In this paper, a generalized upper bound solution is developed for extrusion of bi-metallic rectangular cross-section bars through dies of any shape. The internal, shearing and frictional power terms are derived and they are used in the upper bound model. By using the developed upper bound model, the extrusion pressures for two types of die shapes, an optimum wedge shaped die as a linear die profile and an optimum streamlined die shape as a curved die profile, are determined. The corresponding results for those two die shapes are also determined by using the finite element code and compared with the upper bound results. These comparisons show a good agreement.
W pracy wyprowadzono uogólnione rozwiązanie ograniczenia górnego problemu wytłaczania bimetalowych belek o przekroju prostokątnym za pomocą tłoczników o dowolnym kształcie. Wyznaczono wyrażenia potęgowe opisujące wewnętrzne, ścinające oraz tarciowe obciążenia i zastosowano je w modelu matematycznym omawianego zagadnienia. Zaproponowana metoda badań pozwoliła na określenie nacisku podczas wytłaczania elementów przy użyciu dwóch typów tłocznika – optymalnego klinowego o profilu liniowym oraz tłocznika o zarysie krzywoliniowym, opływowym. W obydwu przypadkach obliczenia porównano z wynikami uzyskanymi z metody elementów skończonych. Porównanie to wykazało dobrą zgodność rozwiązania ograniczenia górnego z rezultatami MES.
Źródło:
Journal of Theoretical and Applied Mechanics; 2013, 51, 1; 105-116
1429-2955
Pojawia się w:
Journal of Theoretical and Applied Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The characteristics of selected triaxiality measures of the stresses for a C(T) specimen dominated by the plane strain state
Autorzy:
Graba, M.
Powiązania:
https://bibliotekanauki.pl/articles/266219.pdf
Data publikacji:
2020
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
mechanika pękania
odkształcenie płaskie
parametry naprężeń
fracture mechanics
C(T)
FEM
stress triaxiality parameter
Lode parameter
constraints
plane strain
Opis:
The paper presents a comprehensive analysis of the stress field and selected triaxiality parameters near the crack tip for C(T) specimen dominated by the plane strain state using the finite element method. It includes some theoretical information about elastic-plastic fracture mechanics, the basics of the FEM modeling and presentation of the numerical results. The FEM analysis includes calculations with large strain assumptions. The influence of the external load and crack length is discussed. Additional elements of the paper are a qualitative assessment of the size of plastic zones and the crack tip opening displacement.
Źródło:
International Journal of Applied Mechanics and Engineering; 2020, 25, 1; 52-74
1734-4492
2353-9003
Pojawia się w:
International Journal of Applied Mechanics and Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The characterization of the stress fields near a crack tip for a compact specimen for elastic-plastic materials dominated by the plane strain state
Autorzy:
Graba, M.
Powiązania:
https://bibliotekanauki.pl/articles/265432.pdf
Data publikacji:
2019
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
mechanika pękania
pole naprężeń
ograniczenia
odkształcenie
strefa plastyczna
pęknięcie
fracture mechanics
stress field
FEM
constraints
plane strain
plastic zone
crack
Opis:
The paper presents a comprehensive analysis of the stress field near a crack tip for a compact specimen dominated by the plane strain state using the finite element method. The analysis also includes the calculation of some parameters of in-plane constraints, both for small and large strain assumptions. It discusses the influence of the material characteristic, relative crack length and external load for the stress field, and the in-plane constraint parameter. The approximation formulas for some in-plane constraint parameters are presented.
Źródło:
International Journal of Applied Mechanics and Engineering; 2019, 24, 3; 549-576
1734-4492
2353-9003
Pojawia się w:
International Journal of Applied Mechanics and Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A comparative study of various models of equivalent plastic strain to fracture
Badanie porównawcze różnych modeli równoważnego odkształcenia plastycznego do pękania
Autorzy:
Mykhalevych, Volodymyr
Dobraniuk, Yurii
Matviichuk, Victor
Kraievskyi, Volodymyr
Тiutiunnyk, Oksana
Smailova, Saule
Kozbakova, Ainur
Powiązania:
https://bibliotekanauki.pl/articles/27315384.pdf
Data publikacji:
2023
Wydawca:
Politechnika Lubelska. Wydawnictwo Politechniki Lubelskiej
Tematy:
ductile fracture criteria
fracture graph
equivalent plastic strain to fracture
stress triaxiality
plane strain
kryteria powstawania pęknięć ciągliwych
wykres pękania
równoważne odkształcenie plastyczne do pękania
trójosiowość naprężeń
naprężenie płaskie
Opis:
For more then half a centre just the same approach to the simulation of the ductile crack formation wasdeveloped independently by the scientific communities of foreign and native researchers. The importance at these studies drastically increased. A set of the characteristics, according to whichit is recommendly to perform thedetail comparison of the existing fracture models is developed. The examples of the analysis of a number of the most popular models by means of obtaining and study their analytical expressions regarding the conditions of the plane state are given. The generalized relations of the know models and a number of separate relations are obtained.
Od ponad pół wieku to samo podejście do modelowania uszkodzeń podczas odkształceńplastycznych jest opracowywane niezależnie przez zespoły naukowe złożone znaukowców zagranicznych i krajowych. W ostatnich dziesięcioleciach znaczenie tych badań dramatycznie wzrosło. Opracowano zestaw cech, zgodnie z którymi proponuje się przeprowadzenie szczegółowego porównania istniejących modeli zniszczenia. Podano przykłady analizy szeregu najpopularniejszych modeli poprzez uzyskanie i badanie ich wyrażeń analitycznych dla warunków płaskiego stanunaprężenia. Otrzymano uogólnione wskaźniki znanych modeli oraz szereg wskaźników indywidualnych.
Źródło:
Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska; 2023, 13, 1; 64--70
2083-0157
2391-6761
Pojawia się w:
Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-5 z 5

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies