Autor: Kaiser, Mohammad Salim - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Role of magnesium and minor zirconium on the wear behavior of 5XXX series aluminum alloys under different environments
Autorzy:: Kaiser, Mohammad Salim
Matin, Mohammad Abdul
Shorowordi, Kazi Mohammad
Powiązania:: https://bibliotekanauki.pl/articles/1819178.pdf
Data publikacji:: 2020
Wydawca:: Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:: aluminum alloys
environment
wear
corrosion
friction
microstructure
stopy aluminium
środowisko
zużycie
korozja
tarcie
mikrostruktura
Opis:: The tribological performance of 5xxx series aluminum alloys with ternary zirconium is evaluated at ambient conditions under dry, wet and saline environment. The experiment has been done using a Pin-on-Disk apparatus under an applied load of 20N. The sliding distances varies ranging from 116m-2772m at a sliding velocity of 0.385 ms-1. The results show that presence of Mg and Zr into this alloy helps to increase their strength and wear resistance under dry sliding condition. But they significantly suffer under wet and corrosive environment due to formation of β-phase Al3Mg2, to slip bands and grain boundaries which may lead to and stress-corrosion cracking. The variation of friction coefficient is observed in wet and corrosive environment due to the formation of oxidation film, lubrication, and corrosion action in solution. The SEM analysis shows that brittle Al3Mg2phase initiate the fracture surface for Al-Mg alloy and Zr addition accelerate the brittleness of the alloy owing the fine precipitates of Al3Zr.
Źródło:: Journal of Mechanical and Energy Engineering; 2020, 4, 3; 209--220
2544-0780
2544-1671
Pojawia się w:: Journal of Mechanical and Energy Engineering
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Role of Si on machined surfaces of Al-based automotive alloys under varying machining parameters
Autorzy:: Razin, Ahmed Asif
Ahammed, Dewan Salsabil
Nur, Maglub Al
Kaiser, Mohammad Salim
Powiązania:: https://bibliotekanauki.pl/articles/2106430.pdf
Data publikacji:: 2022
Wydawca:: Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:: Al-Si alloys
roughness
temperature
chips
microstructure
stopy Al-Si
chropowatość
temperatura
wióry
mikrostruktura
Opis:: A morphological change due to Si contend into Al-based automotive alloys has been conducted on the characterization of machined surfaces in terms of roughness, temperature, chips formation as well as microstructure evaluation under different machining conditions. For this experiment, a shaper machine with HSS single point V-shaped cutting tool is used at different cutting speeds and depths of cut. The experimental results show that the surface roughness of the alloys decreases with the cutting speed and depth of cut but it is more prominent in the case of the cutting speed. This is because of a high cutting speed, which is more associated with the higher temperature and softening the work material leading to better surface finish. Higher Si added alloys also exhibit a better surface finish because the sample content is different fine and hard intermetallic due to ageing treatment, which also makes the alloys more brittle. For brittle and higher hardness, it produces a higher temperature during machining. During machining, relatively curly and short chips are formed by the high Si added alloy because of its low elongation properties. The fracture surfaces of higher Si added alloy display more crack propagation obtained by plate-like Si rich intermetallic.
Źródło:: Journal of Mechanical and Energy Engineering; 2022, 6, 1; 43--52
2544-0780
2544-1671
Pojawia się w:: Journal of Mechanical and Energy Engineering
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "Kaiser, Mohammad Salim" wg kryterium: Autor

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język