Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Al/Al" wg kryterium: Temat


Tytuł:
TEM investigation of phases formed during aluminium wetting of MgO at [100], [110] and [111] orientations
Analiza fazowa metodą TEM produktów reakcji powstałych w czasie zwilżania przez aluminium podłoży MgO o orientacji [100], [100] i [111]
Autorzy:
Morgiel, J.
Sobczak, N.
Pomorska, M.
Nowak, R.
Wojewoda-Budka, J.
Powiązania:
https://bibliotekanauki.pl/articles/354574.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al/MgO reaction
α-Al2O3
MgAl2O4
microstructure
TEM
EDS
reakcja Al/MgO
Al2O3
Opis:
The interaction of liquid aluminium (5N) with single crystal MgO substrates of [100], [110] and [111] orientations (surface roughness <1 nm) were studied using sessile drop wettability test performed at 1000ºC for 1 hour in vacuum (5 x 10-6 mbar). The observations performed using scanning electron microscopy (SEM) showed that the interaction of liquid metal with MgO crystals in all cases resulted in the formation of reaction products region (RPR) of thickness varying from 40 up to 80 microns in depth. In each case the RPR consisted mainly of coarse dendrite-like crystallites of few microns thick surrounded by net of much thinner channels. Occasionally away from the RPR centre the areas built of much finner but also dendrite- or filament-like crystallites were noted. The thin foils for transmission electron microscopy (TEM) investigations were cut using focused ion beam system (FIB) both from drop/RPR as well as RPR/MgO interfacial regions. The electron diffractions proved that the dominating coarse dendrite-like crystallites are of the same α-Al2O3 type throughout the whole RPR for all substrates orientations. Similarly, the colonies of finer crystallites always showed diffraction patterns characteristic for MgAl2O4 spinel. Therefore, the performed investigation indicated, that both the reaction layer depth and the reaction path represented by the sequence and type of phases present in Al/MgO RPR remain roughly similar for all examined orientations, i.e. that the substrate orientation control neither reaction kinetics, nor affects final phase composition of RPR.
Oddziaływanie ciekłego aluminium (5N) z mono-krystalicznymi podłożami o orientacji [100], [110] i [111] (chropowatość <1nm) badano metodą kropli leżącej w 1000ºC przez 1 godzine w dynamicznej próżni rzędu 10-4 Pa. Obserwacje z wykorzystaniem mikroskopii skaningowej (SEM) wykazały, że oddziaływanie ciekłego metalu z kryształami MgO we wszystkich przypadkach prowadziło do wytworzenia strefy produktów reakcji (tzw. reaction produkt region - RPR) o grubości od 40 do 80 mum. W strefach tych wystepowały wydzielenia o kształcie dendrytycznym rozdzielone waskimi kanałami aluminium. Na krawędziach strefy reakcji stwierdzono obecność kolejnej strefy o grubości kilku- kilkunastu-mikrometrów wypełnionej materiałem o jeszcze drobniejszej włóknistej strukturze. Obserwacje mikrostruktury prowadzono z wykorzystaniem mikroskopii transmisyjnej na cienkich foliach wycietych technika FIB zarówno z granic obu stref, oraz z granicy RPR/MgO. Obserwacje te, w powiązaniu z analizą dyfrakcji elektronowych wykazały, że dla MgO wszystkich orientacji dominujace w RPR duże wydzielenia o kształcie dendrytycznym odpowiadaja fazie α- Al2O3. Równoczesnie, analiza dyfrakcji drobniejszych krystalitów zlokalizowanych w pod-strefie ulokowanej na granicach poza centrum RPR wykazała, że mają one budowe charakterystyczna dla spinelu MgAl2O4. Przeprowadzone badania wykazały, że zarówno grubość RPR, a w tym jej pod-strefy drobniejszych wydzieleń na jej obrzeżach, jak też drogą reakcji reprezentowana przez sekwencje i typ wydzielających się faz w czasie oddziaływania ciekłego aluminium jest identyczna dla wszystkich analizowanych monokrystalicznych podłoży MgO, tj. orientacja tych podłoży nie ma wpływu ani na skład fazowy produktów reakcji ani też na kinetykę tego procesu.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 2; 497-500
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Effect of Modifier on the Microstructure of the AlSi10CuNiMn Alloy
Autorzy:
Cais, Jaromir
Heinrich, Jiri
Jirounkova, Klara
Powiązania:
https://bibliotekanauki.pl/articles/103309.pdf
Data publikacji:
2020
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
Al-Si alloy
microstructure
modification
microscopy
stop Al-Si
mikrostruktura
modyfikacja
mikroskopia
Opis:
This paper deals with different types of modifiers and their effect on the microstructure of the Al-Si alloy. For the purposes of this research, strontium, antimony and calcium were used as the modifiers of the AlSi10CuNiMn alloy. Unmodified alloy was cast in order to be compared with the alloy modified by different modifiers in various concentrations. The results of this research were analysed via light and electron microscopy.
Źródło:
Advances in Science and Technology. Research Journal; 2020, 14, 2; 13-18
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A Comparative Study on Ex-Situ & In-Situ Formed Metal Matrix Composites
Autorzy:
Gobalakrishnan, B.
Rajaravi, C.
Udhayakumar, Gobikrishnan
Lakshminarayanan, P. R.
Powiązania:
https://bibliotekanauki.pl/articles/2203734.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
MMCs
Al-SiC
Al-TiB2
extrusion
heat treatment
mechanical properties
microstructure
Opis:
An attempt has been made to synthesize the aluminium based ex-situ (Al-SiC) and in-situ (Al-TiB2) formed metal matrix composites with varying weight percentage of reinforcement contents such as 4wt.%, 6wt.% and 8wt.%. Synthesized composites were subjected to a cold extrusion process followed by heat treatment according to the ASTM B 918-01 standards. The mechanical properties of in-situ composites were evaluated as per the ASTM guidelines and compared with ex-situ formed composites and base metal properties. Superior properties were noticed in the in-situ formed composites and the mechanical properties such as yield strength, Ultimate tensile strength (UTS) and Hardness for both ex-situ and in-situ composites were found to increase with increasing the reinforcement addition. Cold extruded Al-8 wt.% SiC composite properties such as hardness, yield strength and UTS are 87 RB, 152 MPa, 216 MPa respectively. Whereas, for Al-8 wt.% TiB2 composite, the corresponding properties are 94 RB, 192 MPa, 293 MPa. The morphology of the composites is analysed by Optical and Scanning Electron Microscopic (SEM) whereas presence of reinforcement particles such SiC and TiB2 along with intermetallic phases Mg2Si and Al5FeSi are confirmed by EDX, XRD and Element Mapping analyses.
Źródło:
Archives of Metallurgy and Materials; 2023, 68, 1; 171--185
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modifications ALSI7MG0.3 alloys trough CA, SR and SB
Autorzy:
Cais, Jaromír
Lysoňková, Irena
Kraus, Pavel
Powiązania:
https://bibliotekanauki.pl/articles/102369.pdf
Data publikacji:
2018
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
Al-Si alloy
modifier
microstructure
EDX analysis
stop Al-Si
modyfikator
mikrostruktura
analiza EDX
Opis:
This article deals with examing the effect of modifier on changes in microstructure of the alloy AlSi7Mg0.3. The content of the experiment was to examine the effect of addition of calcium, stroncium, and antimony to change the morphology of the eutectic silicon in the alloy type of Al-Si (namely AlSi7Mg0.3). Besides changes in the morphology of eutectic silicon was explored focused on character exlusion modifiers within microstructure of the modified alloy. Examination of the microstructure was realized by scanning electron microscopy and complemented by EDX analysis of the examined samples.
Źródło:
Advances in Science and Technology. Research Journal; 2018, 12, 2; 180-187
2299-8624
Pojawia się w:
Advances in Science and Technology. Research Journal
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Role of Si on machined surfaces of Al-based automotive alloys under varying machining parameters
Autorzy:
Razin, Ahmed Asif
Ahammed, Dewan Salsabil
Nur, Maglub Al
Kaiser, Mohammad Salim
Powiązania:
https://bibliotekanauki.pl/articles/2106430.pdf
Data publikacji:
2022
Wydawca:
Politechnika Koszalińska. Wydawnictwo Uczelniane
Tematy:
Al-Si alloys
roughness
temperature
chips
microstructure
stopy Al-Si
chropowatość
temperatura
wióry
mikrostruktura
Opis:
A morphological change due to Si contend into Al-based automotive alloys has been conducted on the characterization of machined surfaces in terms of roughness, temperature, chips formation as well as microstructure evaluation under different machining conditions. For this experiment, a shaper machine with HSS single point V-shaped cutting tool is used at different cutting speeds and depths of cut. The experimental results show that the surface roughness of the alloys decreases with the cutting speed and depth of cut but it is more prominent in the case of the cutting speed. This is because of a high cutting speed, which is more associated with the higher temperature and softening the work material leading to better surface finish. Higher Si added alloys also exhibit a better surface finish because the sample content is different fine and hard intermetallic due to ageing treatment, which also makes the alloys more brittle. For brittle and higher hardness, it produces a higher temperature during machining. During machining, relatively curly and short chips are formed by the high Si added alloy because of its low elongation properties. The fracture surfaces of higher Si added alloy display more crack propagation obtained by plate-like Si rich intermetallic.
Źródło:
Journal of Mechanical and Energy Engineering; 2022, 6, 1; 43--52
2544-0780
2544-1671
Pojawia się w:
Journal of Mechanical and Energy Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Solution Heat Treatment on Phase Composition and Structure of ZnAl40Cu(1-2)Ti(1-2) Alloys
Autorzy:
Michalik, R.
Powiązania:
https://bibliotekanauki.pl/articles/352321.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Zn-Al alloy
microstructure
phase composition
Opis:
Zn-Al-Cu alloys are characterised by very good tribological properties: high resistances to abrasive wear and adhesive wear, resistance to dry friction, low friction coefficient. Important disadvantages of Zn-Al alloys include, among others low structural and dimensional instability in as-cast stage and during long-period after pouring into moulds. Studies carried out in recent years confirm the problem of dimensional instability of Zn-Al-Cu alloys may be reduced by replace copper partially with titanium. The goal of the studies carried out was to define the influence of heat treatment on the microstructure and phase composition of ZnAl40Cu(1-2)Ti(1-2) alloys. The scope of the investigations included analysis of the phase composition, tests using a scanning electron microscope and a scanning transmission electron microscope, and X-ray microanalysis. The studies carried out indicate a presence of the e-CuZn5 and Ti2ZnAl5, AlxCuyTiz phases in the ZnAl40Cu(1-2)Ti(1-2) alloys.
Źródło:
Archives of Metallurgy and Materials; 2018, 63, 1; 461-466
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The effect of sintering temperature on microstructure and properties of Al - SiC composites
Wpływ temperatury spiekania na mikrostrukturę i własności kompozytów Al - SiC
Autorzy:
Leszczyńska-Madej, B.
Powiązania:
https://bibliotekanauki.pl/articles/350920.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
kompozyty Al-Si
spiekanie
mikrostruktura
metalurgia proszków
Al-SiC composites
sintering
microstructure
cold pressing
tribological properties
Opis:
Attempts have been made to describe the influence of sintering temperature on the microstructure and properties of Al - SiC composites. Mixtures of 100%Al and Al - 5% SiC, Al - 10% SiC were produced by tumbling for 30 minutes in the Turbula T2F mixer. The powders were subsequently cold pressed at pressure 300MPa in a rigid die on a single action press. The green compacts were sintered in nitrogen at 580°C and 620°C for one hour. The main objective of this work was to determine influence of chemical composition and the manufacturing parameters on microstructure and properties of Al - SiC composites produced by powder metallurgy technology.
W pracy przedstawiono wyniki badań kompozytów aluminiowych umacnianych cząstkami węglika krzemu SiC. Wytworzono spiekane kompozyty o zawartości 5% i 10% SiC. Jako materiał referencyjny stosowano Al99,7 wytworzone w takich samych warunkach, jak kompozyty Al - SiC. Materiały wytworzono na drodze jednostronnego prasowania przy zastosowaniu ciśnienia prasowania 300MPa. Kolejno kształtki poddano spiekaniu w atmosferze azotu w temperaturze 580 C oraz 620 C. Na tak wytworzonych spiekach przeprowadzono obserwacje mikrostruktury, pomiar twardości metoda Brinella, próbę zginania oraz przy zastosowaniu testera T05 badanie odporności na zużycie ścierne. Celem pracy jest określenie wpływu składu chemicznego oraz parametrów procesu wytwarzania na mikrostrukturę i właściwości kompozytów Al - SiC wytwarzanych technologia metalurgii proszków.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 1; 43-48
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Plasticity of low aluminum alloys from Fe-Al system
Plastyczność niskoaluminiowych stopów z układu Fe-Al
Autorzy:
Bednarczyk, I.
Jabłońska, M.
Powiązania:
https://bibliotekanauki.pl/articles/354642.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
stopy Fe-Al
próba ściskania na gorąco
mikrostruktura
substruktura
Fe-Al alloys
hot compression test
microstructure
substructure
Opis:
Alloys based on intermetallic phases from the Fe-Al system they belong to a group of high-temperature creep resisting materials of advantageous physicochemical and mechanical properties at an elevated and high temperature. In general, limitation on the capacity for a broad application of intermetals from the Fe-Al system, e.g. as an alternative to expensive alloy steels of specific properties, is their insufficient plasticity, which is a factor inhibiting further their development as constructional materials. The aim of this work is study about the analysis of the influence of hot deformation parameters like a temperature and strain rate on the plasticity and structure changes in alloys on the base Fe-Al system. These alloys are competitive for their cost and properties in comparison with stainless and acid resistance steels. Were analyzed the properties determined in hot compression test of cast alloys Fe-28Al, Fe-28Al-5Cr, contain microelements Mo, Zr, C, B. The tests were carried out on the range of temperature 700°C - 1100°C with strain rate 0,1 s-1. The results indicated that the Cr addition had an positively effect on the plasticity properties. Moreover exhibited that the Cr addition had an influence on the mechanism of the rebuilding the structure changes.
Stopy na osnowie faz międzymetalicznych z układu Fe-Al, zaliczane są do grupy tworzyw żarowytrzymałych, posiadających korzystne właściwości fizykochemiczne i mechaniczne. Zasadniczym problemem ograniczającym ich powszechne stosowanie jest niska plastyczność i skłonność do kruchego pękania co powoduje zahamowanie w dalszym rozwoju jako materiałów konstrukcyjnych. Celem tej pracy jest ocean wpływu parametrów takich jak temperatura, prędkość odkształcenia na plastyczność i zmiany struktury stopów z układu Fe-Al. Ze względu na niski koszt oraz właściwości są konkurencyjne w porównaniu do stali nierdzewnych i kwasoodpornych. Analizowano właściwości w próbie ściskania na gorąco dla odlewniczych stopów Fe-28Al, Fe-28Al-5Cr, zawierających mikrododatki Mo, Zr, C, B. Próby były prowadzone w zakresie temperatury 700 ÷ 1100°C z prędkością odkształcenia 0,1 s-1. Wyniki wskazują, że mikrododatek Cr ma zdecydowany wpływ na właściwości plastyczne. Dodatkowo mikrododatek Cr ma wpływ na zmianę mechanizmu odbudowy struktury.
Źródło:
Archives of Metallurgy and Materials; 2012, 57, 1; 271-276
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modification of Aluminium-Silicon Near-Eutectic Alloy with Use of Electrolysis of Sodium Salt
Autorzy:
Białobrzeski, A.
Pezda, J.
Jarco, A.
Powiązania:
https://bibliotekanauki.pl/articles/351019.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al-Si alloys
electrolysis
tensile strength
microstructure
Opis:
The present work discusses results of preliminary tests concerning the technology of continuous dosage of sodium to a metallic bath from the aspect of modification of EN AC-44200 alloy, through the use of a multiple compound (salt) of sodium. The technology consists in continuous electrolysis of sodium salts occurring directly in a crucible with liquid alloy. As a measure of the degree of alloy modification over the course of testing, the ultimate tensile strength (UTS or Rm) and analysis of microstructure are taken, which confirm the obtained effects of the modification on the investigated alloy. Assurance of stable parameters during the process of continuous modification with sodium, taking into consideration the fact of complex physical-chemical phenomena, requires additional tests aimed at their optimization and determination of a possibility of implementation of such technology in metallurgical processes.
Źródło:
Archives of Metallurgy and Materials; 2017, 62, 4; 2371-2374
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Variable Manganese Content on Microstructure of Al-Cu Alloys
Autorzy:
Stąpór, S.
Górny, M.
Kawalec, M.
Gracz, B.
Powiązania:
https://bibliotekanauki.pl/articles/355992.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Al-Cu-Mn alloys
microstructure
macrostructure
DSC
Opis:
The presented access the influence of Mn content (0-0.94 wt.%) on the course of the cooling curves, phase transformation, macrostructure, and microstructure of Al-Cu alloys for three series: initial (Series I), with the addition of an AlTi master (Series II), and modified with AlTi5B1 (Series III). The maximum degree of undercooling ΔT was determined based on the cooling curves. The surface density of the grains (NA ) was determined and associated with the inverse of solidification interval 1/ΔTk . Titanium (contained in the charge materials as well as the modifier) has a significant effect on the grinding of the primary grains in the tested alloys. A DSC thermal analysis allowed for the determination of phase transition temperatures under conditions close to equilibrium. For series II and III, the number of grains decreases above 0.2 wt.% Mn with a simultaneous increase in solidification interval 1/ΔT2 . The presence of Al2 Cu eutectics as well as the Cu-, Fe-, and Mn-containing phases in the examined samples was demonstrated using scanning electron microscopy.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 4; 1377-1383
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Mikrostruktura i właściwości mechaniczne eutektycznego stopu Al-33%Cu po zastosowaniu odkształcania metodą KoBo
Microstructure and mechanical properties of Al-33%Cu eutectic alloy after KoBo deformation
Autorzy:
Brzezińska, A.
Mikuszewski, T.
Sobota, J.
Rodak, K.
Powiązania:
https://bibliotekanauki.pl/articles/211754.pdf
Data publikacji:
2018
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Obróbki Plastycznej
Tematy:
stopy Al-Cu
mikrostruktura
właściwości mechaniczne
SPD
metoda KoBo
Al-Cu alloy
microstructure
mechanical properties
KoBo method
Opis:
Przedmiotem badań mikrostruktury i właściwości mechanicznych był eutektyczny stop Al-33%Cu poddany odkształcaniu metodą KoBo. Stop bezpośrednio po odlaniu został przetoczony do średnicy 49 mm, a następnie wyciskany metodą KoBo do średnicy 9 mm. Proces prowadzono przy kącie obrotu matrycy 8°. Badania mikrostruktury wykonano na mikroskopie świetlnym Olympus GX71. Obserwacji mikrostruktury cienkich folii dokonano na skaningowo-transmisyjnym mikroskopie elektronowym (STEM) Hitachi HD-2300A z działem typu FEG, który jest wyposażony w detektor EDS, umożliwiający analizę składu chemicznego. Analizy przełomów dokonano na skaningowym mikroskopie elektronowym (SEM) Hitachi S-340N. Próbę ściskania przeprowadzono na maszynie Zwick/Roell Z100. Próba została wykonana w temperaturze otoczenia na próbkach w kształcie walców o średnicy 6 mm i wysokości 9 mm, zastosowano siłę nacisku 100 kN. Do wykonania pomiarów twardości użyto mikrotwardościomierza Future-Tech FM-700. Badano twardość stopów pod obciążeniem 0,1 kg. Pomiary przewodności elektrycznej właściwej przeprowadzono na urządzeniu SIGMATEST 2.096 firmy FOERSTER. Udowodniono, że zastosowana metoda KoBo pozwala na fragmentację mikrostruktury badanego stopu, w wyniku czego otrzymuje się fazy o globularnej morfologii. Mimo zastosowanego procesu SPD nie dochodzi do całkowitego ujednorodnienia struktury: obserwuje się zróżnicowaną wielkość faz jako pozostałość po procesie odlewania, a także obserwuje się mikroobszary nieodkształcone. Odkształcenie stopu metodą KoBo przyczynia się do wzrostu właściwości wytrzymałościowych i plastycznych. Proces KoBo może być zastosowany do rozdrabniania struktury stopu o składzie eutektycznym.
Recent investigations are focused on microstructure and mechanical properties characterization of Al-33%Cu eutectic alloy after application KoBo method. Samples after casting and turning to 49 mm in diameter were extruded to 9 mm in diameter. Process was performed at torsion angle 8°. Microstructural investigations were performed by using light microscopy Olympus GX71, and scaning electron microscopy (SEM) Hitachi S-340N, and scaning transmission electron microscopy (STEM) Hitachi HD-2300A equipped with FEG gun, allowing analysis of chemical composition. Compression tensile strength were performed on the machine Zwick/Roell Z100. The test was carried out at ambient temperature on the Samales in the shape of cylinders with a diameter of 6 mm and a height of 9 mm, a pressure force of 100 kN was applied. The Future-Tech FM-700 machine was used to perform hardness measurements. The hardness of alloys under a load of 0.1 kg was tested. The electrical conductivity measurements were carried out on the SIGMATEST 2.096 FOERSTER device. The results shows that the KoBo method allows to grain fragmentation and improve plastic properties and mechanical properties of alloy. It was observed differentiation in the size of the phases obtained during casting process and additionally, after KoBo deformation were observed non-deformed microareas. After KoBo deformation increase the strength and plastic properties of alloy. KoBo method can be used to fragmentation eutectic alloys Al-33Cu.
Źródło:
Obróbka Plastyczna Metali; 2018, 29, 2; 139-150
0867-2628
Pojawia się w:
Obróbka Plastyczna Metali
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Advantages of colour etching in quality control of recycled Al-Si cast alloys
Autorzy:
Tillová, Eva
Kuchariková, Lenka
Chalupová, Mária
Belan, Juraj
Vaško, Alan
Herčko, Adrián
Powiązania:
https://bibliotekanauki.pl/articles/104005.pdf
Data publikacji:
2019
Wydawca:
Stowarzyszenie Menedżerów Jakości i Produkcji
Tematy:
Al-Si cast alloys
colour metallography
microstructure
quality control
stopy odlewane Al-Si
mikrostruktura
kontrola jakości
metalografia kolorowa
Opis:
Colour Metallography is a set of light metallographic microscopy methodologies that utilize phase colour contrast as a source of new structure information compared to conventional techniques. In many cases, colour contrast can be induced where no identifiable phase contrast is obtained by conventional techniques. With the help of colour contrast, we gain new information on the structure of Al-Si alloys, especially intermetallic phases, in which the benefits of its use in casting quality control are of benefit. Blue-yellow contrast is definitely more pronounced than dark grey or light grey contrast. There is no substantial reproducible colour reproduction, since it is irrelevant whether the two phases are distinguished by blue-yellow or green-ocher contrast. When using the colour contrast, the structural components differ not only according to their microscopic appearance, but also based on the knowledge of the chemical composition of alloys, interactions between structural components, knowledge of the possible influence of Al-alloys structure (e.g. refining, modifications, heat treatment). Colour contrast in quality control of Al-Si alloys was applied to AlSiMg cast alloy (AlSi7Mg0.3; AlSi7MgTi; AlSi10MgMn; etc.).
Źródło:
Quality Production Improvement - QPI; 2019, 1, 1; 296-303
2657-8603
Pojawia się w:
Quality Production Improvement - QPI
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza wpływu mikrostruktury na odporność korozyjną stopu tytanu Ti6Al7Nb
The analysis of the effect of microstructure on the corrosion resistance of titanium alloy Ti6Al7Nb
Autorzy:
Zięty, A.
Lachowicz, A.
Powiązania:
https://bibliotekanauki.pl/articles/99013.pdf
Data publikacji:
2014
Wydawca:
Politechnika Śląska. Katedra Biomechatroniki
Tematy:
Ti6Al7Nb
biomateriał
mikrostruktura
obróbka cieplna
Ti-6Al-7Nb
biomaterial
microstructure
thermal treatment
Opis:
Stopy tytanu, takie jak Ti6Al4V, czy analizowany Ti6Al7Nb należą do stopów o strukturze dwufazowej α+β. Kształtowanie ich mikrostruktury wynika ze specyficznych cech fizycznych tytanu, ale i z warunków odkształcania na gorąco oraz obróbki cieplnej. Procesy te powinny uwzględniać związek między mikrostrukturą a wytrzymałością implantu, jego twardością, plastycznością, odpornością na zmęczenie, zużycie ścierne i co najważniejsze – odpornością na korozję. Przeanalizowano istniejącą literaturę pod kątem wpływu mikrostruktury stopu tytanu Ti6Al7Nb na jego odporność korozyjną w symulowanych płynach ustrojowych. Jej różnorodność związana jest ze sposobem przetwarzania stopu, co również było obiektem analizy i obserwacji.
Titanium alloys, such as Ti6Al4V, or analyzed in this paper Ti6Al7Nb alloys are two-phase structure of α + β. Shaping their microstructure due to the specific physical characteristics of the titanium, its hot deformation and heat treatment. These processes should take into account the relation between the microstructure and strength of the implant, its hardness, ductility, resistance to fatigue, wear and what is the most important - corrosion resistance. Existing literature was analyzed for effects of titanium alloy microstructure Ti6Al7Nb its corrosion resistance in simulated body fluids. It is associated with a variety of melt processing method, which also has been the subject of analysis and observation.
Źródło:
Aktualne Problemy Biomechaniki; 2014, 8; 187-192
1898-763X
Pojawia się w:
Aktualne Problemy Biomechaniki
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Mikrostruktura i właściwości stopu Ti-6Al-7Nb po dyfuzyjnej obróbce utwardzającej tlenem
Microstructure and properties of oxygen diffusion strengthened Ti-6Al-7Nb alloy
Autorzy:
Moskalewicz, T.
Wendler, B.
Zimowski, S.
Milc, S.
Czyrska-Filemonowicz, A.
Powiązania:
https://bibliotekanauki.pl/articles/283843.pdf
Data publikacji:
2009
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Polskie Towarzystwo Biominerałów
Tematy:
stop Ti-6Al-7Nb
mikrostruktura
obróbka tlenem
Ti-6Al-7Nb alloy
microstructure
oxygen diffusion
Opis:
W pracy przedstawiono charakteryzację mikrostruktury, właściwości mikro-mechanicznych i tribologicznych stopu Ti-6Al-7Nb w stanie dostawy oraz po obróbce utwardzającej tlenem. Badania mikrostruktury przeprowadzono za pomocą skaningowej i transmisyjnej mikroskopii elektronowej na próbkach z przekroju poprzecznego. Stwierdzono, że strefa przypowierzchniowa utwardzonego stopu zbudowana była głównie z roztworu stałego tlenu w tytanie α(O). Zastosowana obróbka powierzchniowa istotnie poprawiła twardość oraz właściwości tribologiczne stopu (wzrost odporności na zużycie przez tarcie, zmniejszenie współczynnika tarcia).
The microstructure as well as micro-mechanical and tribological properties of the as received and glow discharge plasma thermal oxidized Ti-6Al-7Nb alloy were examined. Scanning and transmission electron microscopy investigations on cross-section specimens were used for microstructure investigations. The α (O) solid solution enriched by oxygen up to 22at % was mainly present in the near-surface region. Applied sur-face treatment significantly improved microhardness and tribological properties (wear resistance, friction coefficient) of the alloy.
Źródło:
Engineering of Biomaterials; 2009, 12, no. 89-91; 126-129
1429-7248
Pojawia się w:
Engineering of Biomaterials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Characteristics of Al-Fe sinters made by the powder metallurgy route
Charakterystyka spieków Al-Fe wytworzonych metodą metalurgii proszków
Autorzy:
Majchrowska, M.
Lasek, K.
Nowak, M.
Pałka, P.
Sułkowski, B.
Powiązania:
https://bibliotekanauki.pl/articles/264175.pdf
Data publikacji:
2018
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Wydawnictwo AGH
Tematy:
Al/Fe sinters
powder metallurgy
interface
intermetallic compounds
microstructure
spieki Al/Fe
metalurgia proszków
interfejs
związki międzymetaliczne
mikrostruktura
Opis:
The Al/Fe material was prepared by the powder metallurgy route with an additional intermediate stage which was a centrifuge of powder mixture. The application of the centrifuge stage was applied to obtain circular phase distribution of Al-rich phases in a sintered material. Iron powder with a particle size under 100 μm and aluminum powder with a particle size of about 25 μm, were used as starting materials. To determine the effect of centrifuging time on the distribution of Fe-Al particles, scanning electron microscopy (SEM, EDS) and XRD techniques were used. Microstructure observations show the influence of the centrifuging time on the distribution of Fe particles. It was observed that a longer centrifuging time caused changes in the ratio concentration of elements and allowed the growth of the intermetallic phase at the interface between solid Al and Fe particles.
Spiekane materiały Al/Fe wytwarzano metodą metalurgii proszków z wprowadzeniem etapu pośredniego w postaci odwirowania mieszaniny proszku. Etap wirowania miał na celu uzyskanie kulistego rozkładu faz bogatych w Al w spiekanym materiale. Proszek żelaza o wielkości cząstek poniżej 100 μm i proszek aluminium o wielkości cząstek około 25 μm zastosowano jako materiały wyjściowe. W celu określenia wpływu czasu wirowania mieszanki na rozkład faz w wytworzonym materiale zastosowano techniki skaningowej mikroskopii elektronowej (SEM, EDS) i dyfraktometrii rentgenowskiej (XRD). Obserwacje mikrostruktury wykazały istotny wpływ czasu wirowania na mikrostrukturę uzyskanych spieków. Zaobserwowano, że dłuższy czas wirowania spowodował zmianę stosunku stężenia pierwiastków i pozwolił na wzrost fazy międzymetalicznej na granicy faz między stałymi cząstkami Al i Fe. Badania mikrotwardości obszarów spiekanego materiału świadczą o zwiększeniu twardości w obszarach nowo utworzonych faz międzymetalicznych.
Źródło:
Metallurgy and Foundry Engineering; 2018, 44, 4; 195-203
1230-2325
2300-8377
Pojawia się w:
Metallurgy and Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies