Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "Mgła wodna" wg kryterium: Temat


Tytuł:
NOWE MOŻLIWOŚCI OCHRONY DREWNIANYCH ZABYTKÓW PRZED POŻAREM. SYSTEM GASZENIA MGŁĄ WODNĄ
NEW POSSIBILITIES OF FIRE PREVENTION IN WOODEN HISTORICAL MONUMENTS. THE WATER MIST EXTINGUISHING SYSTEM
Autorzy:
Ogrodzki, Piotr
Powiązania:
https://bibliotekanauki.pl/articles/538089.pdf
Data publikacji:
2003
Wydawca:
Narodowy Instytut Dziedzictwa
Tematy:
zagrożenie pożarowe
pożary zabytków
ochrona przeciwpożarowa
środki ogniochronne
mgła wodna
CERBER
Opis:
Fire poses a constant threat to historical monuments, especially wooden sacral objects. Each year statistics prepared by the State Fire Brigade services list new destroyed objects. The diminished entries in the register and inventory encompass both categories of historical monuments – mobile and immobile. For many years now, the number of fires of historical objects has maintained a steady level of about 150. The future retention of such a threat will signify that in the coming ten years some 1500 monuments will simply disappear from the map of Poland. In 2003 the Polish market has noted the appearance of new, extremely noteworthy technological solutions specially devised for the protection of historical wooden architecture, including a permanent fire extinguishing installation. The first installation of this sort was applied in the church of St. Sebastian in Wieliczka. The extinguishing system control was installed next to the side entrance. The water supply and pneumatic set was placed in a concrete subterranean receptacle built in the church plot, thus resolving the localisation of the hydrophores, gas cylinders, valves and other elements of water supply. The reinforced concrete chamber required an area of only 10 sq. m. The hydrophore chamber adjoins an additional hydrant attachment. Depending on the local sources supplying the system with water its utilization may assume assorted forms. On the one hand, it makes it possible to fill the receptacles (in case of a water shortage in the course of extinguishing a fire) and, on the other hand, it can be used by special units which, upon arrival, can pump water into the whole extinguishing system. The pipe installation is built partially of oxidized steel pipes and copper. Vertical pipes were introduced into the attic by means of a passage through the sacristy. The pipes were concealed with the battens and thus rendered them totally invisible. The church elevation contains only slightly discernible small mist nozzles. Owing to the height of the outer walls the nozzles are placed on two levels: halfway up the walls and underneath the eaves, together with heat detectors. The aesthetic execution of whole installation made it possible to avoid impairing the historical monument. The first extremely important step towards an active protection of wooden architecture against fire has been made. The owners of historical monuments, conservators and designers have been provided with a new instrument – the water mist extinguishing system. An additional source of satisfaction is the fact that this is a Polish solution, to be taken into consideration in all plans dealing with the complex tasks of an anti-fire protection of historical monuments.
Źródło:
Ochrona Zabytków; 2003, 1-2; 210-218
0029-8247
Pojawia się w:
Ochrona Zabytków
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modern Trends of Fire Protection in Rolling Stock 2013
Systemy wykrywania pożaru do zastosowań w taborze szynowym 2013
Autorzy:
Klinger, M.
Powiązania:
https://bibliotekanauki.pl/articles/214899.pdf
Data publikacji:
2013
Wydawca:
Instytut Kolejnictwa
Tematy:
fire protection
fire fighting
water mist
rolling stock
ochrona przeciwpożarowa
straż pożarna
mgła wodna
tabor kolejowy
Opis:
The author at first emphasizes that a key role in the protection of human life and protection against damage to equipment in the event of a fire plays proper and early detection. Then discuss the physical phenomena used in different detection techniques used in rail vehicles also providing concrete practical solutions. In the article author also takes into account the impact of the proper placement of detectors in the efficiency of the system, and presents the results of their effectiveness.
Autor na wstępie podkreśla, że kluczową rolę w ochronie życia ludzkiego oraz zabezpieczeniu przed stratami materialnymi w przypadku ewentualnego pożaru odgrywa sprawne i wczesne jego wykrywanie. Następnie omawia zjawiska fizyczne wykorzystane w różnych technikach detekcji stosowanych w pojazdach szynowych, przedstawiając również konkretne praktyczne rozwiązania. W artykule Autor uwzględnia również wpływ właściwego rozmieszczenia czujek na efektywność działania instalacji, a także prezentuje wyniki badań ich skuteczności.
Źródło:
Problemy Kolejnictwa; 2013, 160; 77-98
0552-2145
2544-9451
Pojawia się w:
Problemy Kolejnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Aktywne metody tłumienia detonacji w mieszaninach gazowych
Active methods of detonation suppression in gaseous mixtures
Autorzy:
Porowski, R.
Zieziula, D.
Powiązania:
https://bibliotekanauki.pl/articles/136715.pdf
Data publikacji:
2017
Wydawca:
Szkoła Główna Służby Pożarniczej
Tematy:
detonacja
tłumienie
mgła wodna
proszek gaśniczy
gaz obojętny
detonation
suppression
water mist
dry powder
inert gas
Opis:
W artykule przedstawiono przegląd aktywnych metod tłumienia detonacji w mieszaninach gazowych. Opisane w nim zostały metody tłumienia detonacji za pomocą gazu, proszków gaśniczych oraz mgły wodnej. Pomimo znacznej poprawy w zakresie zarządzania i eksploatacji urządzeń, które przetwarzają substancje palne, wciąż istnieje potrzeba stworzenia innowacyjnych metod i środków ochrony przeciwwybuchowej. Podstawowym celem tych urządzeń jest ograniczanie potencjalnych skutków występowania zdarzeń, które mogą wywołać eksplozję. Czynnikami, które mogą się przyczyniać do zmniejszenia skutków wybuchu, są między innymi minimalizacja wystąpienia uszkodzeń i wycieków, ulepszona konstrukcja oraz poprawa procedur operacyjnych i zarządzania bezpieczeństwem w warunkach przemysłowych.
Paper presents the overview of the active methods of detonation suppression processes in reactive gaseous mixtures. In this paper the influence of the inert gas zone, dry powder and water mist on explosion processes was investigated. It was based on the literature review. Despite the significant improvements in the management and service of installations which process the materials of an explosive nature, there is still a need to create the innovative methods and measures to ensure the proper level of explosion safety. The primary purpose of such devices is to minimize the incidence of events that could potentially cause an explosion. The elements, that may contribute to reduce the effect of explosion are among others, the mitigation of explosions damages and flammable substance leaks as well as operating procedures and safety management in industrial applications.
Źródło:
Zeszyty Naukowe SGSP / Szkoła Główna Służby Pożarniczej; 2017, 2, 62; 83-97
0239-5223
Pojawia się w:
Zeszyty Naukowe SGSP / Szkoła Główna Służby Pożarniczej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ wielkości średnic kropli mgły wodnej na efektywność tłumienia pożarów i chłodzenie
Influence of water mist drop size on efficiency of fire suppression and cooling
Autorzy:
Zbrożek, P.
Prasuła, J.
Powiązania:
https://bibliotekanauki.pl/articles/373131.pdf
Data publikacji:
2009
Wydawca:
Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej im. Józefa Tuliszkowskiego
Tematy:
mgła wodna
rozpylanie cieczy
tlumienie pożarów
urządzenia gaśnicze
atomization of liquids
extinguishing equipment
fire suppression
water mist
Opis:
W artykule przedstawiono ogólne informacje dotyczące właściwości i parametrów mgły wodnej istotne z uwagi na zastosowania gaśnicze. Wyjaśniono mechanizmy gaśnicze mgły wodnej i czynniki sprzyjające efektywności gaśniczej. Poddano analizie wpływ wielkości średnic kropel w mgle wodnej z uwagi na tłumienie pożarów i chłodzenie gazów w gaszonej przestrzeni. Podano optymalne wartości średnic kropel w mgle wodnej w odniesieniu do celów gaśniczych, w szczególności w obiektach zabytkowych.
This article describes general information concerning characteristics and parameters of water mist important for extinguishing applies. Extinguishing mechanisms and factors favourable for the efficiency of extinguishing process were explained. Influence of water mist drop size on the efficiency of fire suppression and cooling of gases in extinguishing space was analyzed. Optimal values of water mist drop diameters in relation to extinguishing purposes were given, particularly in heritage buildings.
Źródło:
Bezpieczeństwo i Technika Pożarnicza; 2009, 3; 113-148
1895-8443
Pojawia się w:
Bezpieczeństwo i Technika Pożarnicza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza porównawcza stałych urządzeń gaśniczych - część I
The analysis of fire extinguish systems - part I
Autorzy:
Sowa, T.
Powiązania:
https://bibliotekanauki.pl/articles/372703.pdf
Data publikacji:
2010
Wydawca:
Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej im. Józefa Tuliszkowskiego
Tematy:
gaszenie
instalacje przeciwpożarowe
klasyfikacja SUG
mgła wodna
tryskacze
fire extinguish systems classification
fire protection installations
sprinklers
suppression
water mist
Opis:
Artykuł zawiera podstawowe informacje o stałych urządzeniach gaśniczych: wodnych, gazowych, i alternatywnych dla nich. Podstawowe informacje obejmują opis ogólny systemu, jego wady i zalety oraz typowe miejsca instalacji. Podstawą dla artykułu były informacje zebrane z pozycji literaturowych, doświadczeń projektantów, instalatorów, użytkowników i informacje uzyskanych od firm projektujących i wykonujących stałe urządzenia poszczególnych typów. Przeanalizowano elementy wpływające bezpośrednio i pośrednio na niezawodność, praktyczność i kosztowność poszczególnych systemów gaśniczych, takie jak m.in. koszt l m3 chronionej powierzchni, bezpieczeństwo ludzi, skuteczność działania. W ten sposób dokonana analiza pozwala wskazać, jakie elementy wpływają na optymalne wykorzystanie stałych urządzeń gaśniczych i jak wybrać odpowiedni środek gaśniczy w zależności od cech charakterystycznych powierzchni chronionej i priorytetów inwestora.
This article contains a basic information about fire extinguishing systems, especially: sprinklers and other systems based on water, gaseous and alternative systems. It includes introduction and overview of the systems, their advantages and disadvantages as well as application areas. Specialist literature, experience of the designers, fitters and users as well as information from producers of these systems were used by the author in order to write this paper. Elements which have the indirect influence on reliability, practical sense and cost of individual fire suppression systems (e.g. l m[^3] cost of a protected area), people security and effectiveness were discussed. This type of analysis leads to the conclusions, which can give the answer for the following problems: what elements are important for effectiveness of fire suppression and what suppression agents should be used in the case of various types of buildings and facilities such as manufactured homes, high-rise buildings, warehouse facilities and manufacturing facilities.
Źródło:
Bezpieczeństwo i Technika Pożarnicza; 2010, 1; 113-132
1895-8443
Pojawia się w:
Bezpieczeństwo i Technika Pożarnicza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Low Pressure Water Mist Fire Protection System
Niskociśnieniowy system mgły wodnej do ochrony przeciwpożarowej
Autorzy:
Pikulski, K.
Powiązania:
https://bibliotekanauki.pl/articles/215050.pdf
Data publikacji:
2013
Wydawca:
Instytut Kolejnictwa
Tematy:
fire protection
water
water mist
low pressure water mist system
ochrona przeciwpożarowa
woda
mgła wodna
system niskociśnieniowej mgły wodnej
Opis:
The article describes the problem of seeking new and low cost extinguishing agents that are still current problem. Author shows that the most common, cheapest and neutral to the environment, and at the same time an effective extinguishing agent is water. Using the water as a mist strongly reduces the formation of post-fire losses. The paper was discussed Polish low-pressure spray solution and areas of its possible application.
W artykule opisano poszukiwania nowych i jednocześnie tanich środków gaśniczych. Autor udowadnia, ze najpowszechniejszym, najtańszym i obojętnym dla środowiska naturalnego, a równocześnie skutecznym środkiem gaśniczym jest woda, której stosowanie w postaci mgły wodnej zdecydowanie ogranicza powstawanie strat popożarowych. W artykule omówiono polską technologię generowania mgły niskociśnieniowej oraz możliwe obszary zastosowania mgły wodnej w systemach ochrony pożarowej.
Źródło:
Problemy Kolejnictwa; 2013, 160; 99-108
0552-2145
2544-9451
Pojawia się w:
Problemy Kolejnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analiza porównawcza stałych urządzeń gaśniczych - część II
The analysis of fire extinguish systems - part II
Autorzy:
Sowa, T.
Powiązania:
https://bibliotekanauki.pl/articles/373264.pdf
Data publikacji:
2010
Wydawca:
Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej im. Józefa Tuliszkowskiego
Tematy:
gaszenie
instalacje przeciwpożarowe
klasyfikacja SUG
mgła wodna
tryskacze
fire extinguish systems classification
fire protection installations
sprinklers
suppression
water mist
Opis:
Artykuł jest kontynuacją pierwszej części artykułu zamieszczonego w kwartalniku "Bezpieczeństwo i technika pożarnicza" i zawiera w głównej mierze kontynuacje rozpoczętego procesu myślowego oraz najważniejsze wnioski będące jego efektem. Po przeanalizowaniu głównych elementów wpływających bezpośrednio i pośrednio na poziom funkcjonalności i skuteczności poszczególnych systemów gaśniczych przedstawiono wnioski pozwalające wskazać, jakie elementy wpływają na optymalne wykorzystanie stałych urządzeń gaśniczych.
The article is a continuation of first part, which has featured in the quarterly "Safety and fire" and contains mainly continuation of the started train of thought and the most important conclusions of it. After the analysis of main elements influencing direct and indirect on a functionality and effectiveness level of each fire extinguish system, there are started conclusions which help to show, which parts influencing optimally on use of fire extinguish systems.
Źródło:
Bezpieczeństwo i Technika Pożarnicza; 2010, 3; 141-146
1895-8443
Pojawia się w:
Bezpieczeństwo i Technika Pożarnicza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Shaping the Structure and Properties of High Quality Silumin Castings in Metal Molds Cooled with Water Mist
Autorzy:
Władysiak, R.
Powiązania:
https://bibliotekanauki.pl/articles/381548.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative material
casting technology
cooling
water mist
permanent mould casting
materiał innowacyjny
technologia odlewnicza
chłodzenie
mgła wodna
forma odlewnicza
Opis:
The paper presents some aspects of the theory and technology of high quality silumin castings in metal molds cooled pointed with water mist stream. The results of the work relate to improvement of the properties of silumin casts by affecting the cooling of the liquid silumin in gravity cast in metal mold and the possibility of controlling the solidification and crystallization of the casting. The high efficiency required from the cooling system is a consequence of an optimal selection of parameters of the generated mist and the maximum use of the phenomenon of water droplets evaporation on the surface of the cooled mold. The study showed that sequential spot cooling with use of water mist, characterized by a wide range of control means and a high maximum heat transfer efficiency, enables to control the flow of heat between the casting and the mold and it allows for a layered solidification leading to the realization of the entire cast solidification in the expected way: directional or simultaneous. Consequently, the results are: improvement of the quality of the castings as a result of the elimination of defects and significant reduction in shrinkage porosity in the casting, an increase of the homogeneity and fineness of the microstructure, about 25% increase in the mechanical properties.
Źródło:
Archives of Foundry Engineering; 2013, 13, 2 spec.; 98-105
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Computer control the cooling process in permanent mold casting of Al-Si alloy
Sterowanie komputerowe procesem chłodzenia formy w odlewaniu kokilowym siluminów
Autorzy:
Władysiak, R.
Powiązania:
https://bibliotekanauki.pl/articles/353901.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative materials & casting technologies
cooling
water mist
Al-Si alloy
innowacyjne materiały i technologie odlewnicze
chłodzenie
mgła wodna
stop Al-Si
Opis:
The paper presents the test results of a computerized control system the sequential cooling process of permanent mold with use of water mist in the gravity die casting process. It describes the process for preparing high-quality casts made of AlSi7Mg alloy that achieves enhanced mechanical properties. A scheme of developed device and drivers for selected methods of sequence cooling for manufacturing of castings made in permanent steel mold was presented here. Also the microstructure and mechanical properties of received aluminium casts were described. It was shown that the use of a computer system to control the water mist cooling point of the mold not only accelerates the cooling of the cast and the gravity die casting cycle shortens, but also it has a positive effect on the microstructure and mechanical properties of castings made of unmodified AlSi7Mg alloy in a raw state.
W pracy przedstawiono wyniki badań komputerowego systemu sterowania sekwencyjnym chłodzeniem kokili mgła wodna w odlewaniu grawitacyjnym. Opisano proces otrzymywania wysokojakościowych odlewów z siluminu AlSi7Mg o podwyższonych właściwościach mechanicznych. Przedstawiono opracowane urządzenie, programy sterujące dla zadanych metod wytwarzania odlewów kokilowych i sekwencji chłodzenia. Przedstawiono mikrostrukturę i własności mechaniczne otrzymanych odlewów siluminowych. W pracy wykazano, że zastosowanie systemu komputerowego do sterowania chłodzeniem punktowego mgła wodna nie tylko przyspiesza stygnięcie odlewu i skraca cykl odlewania kokilowego, ale również korzystnie wpływa na mikrostrukturę i własności mechaniczne odlewów z niemodyfikowanego siluminu AlSi7Mg w stanie surowym.
Źródło:
Archives of Metallurgy and Materials; 2013, 58, 3; 977-980
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Analysis of Crystallization Process of Intensive Cooled AlSi20CuNiCoMg Alloy
Autorzy:
Władysiak, R.
Kozuń, A.
Dębowska, K.
Pacyniak, T.
Powiązania:
https://bibliotekanauki.pl/articles/379541.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technologies
innovative foundry materials
casting die cooling
water mist
silumin
innowacyjne technologie odlewnicze
innowacyjne materiały odlewnicze
odlewanie kokilowe
mgła wodna
Opis:
The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system. The paper presents results of investigation of crystallization process and microstructure of multicomponent synthetic hypereutectic alloy AlSi20CuNiCoMg. The study was conducted for unmodified silumin on the research station allowing the cooling of the special permanent sampler using a program of computer control. Furthermore the study used a thermal imaging camera to analyze the solidification process of multicomponent alloy. The study demonstrated that the use of mold cooled with water mist stream allows in wide range to form the microstructure of hypereutectic multicomponent silumin. It leads to higher homogeneity of microstructure and refinement of crystallizing phases of casting.
Źródło:
Archives of Foundry Engineering; 2017, 17, 2; 137-144
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Evaluation of the Parameters of the Dispersed Stream Generated by Various Types of Water Nozzles
Ocena parametrów strumieni rozpylonych wytwarzanych przez dysze wodne różnego typu
Autorzy:
Wąsik, Wiktor
Powiązania:
https://bibliotekanauki.pl/articles/35052791.pdf
Data publikacji:
2023
Wydawca:
Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej im. Józefa Tuliszkowskiego
Tematy:
water nozzles
water spray
spray spectrum
mass spray density
water mist
dysze wodne
rozpylanie wody
widmo rozpylenia
masowa gęstość zraszania
mgła wodna
Opis:
Purpose: The purpose of the research was to determine the parameters of the micro- and macro-structure of the streams generated by nozzles of different types, and to identify potential applications of the tested water nozzles, including firefighting and air pollution removal. Project and methods: TF6 FCN, TF6 V, NF 15 and CW 50 water nozzles were tested. At supply pressures of 0.2 MPa, 0.4 MPa and 0.6 MPa, the basic parameters of micro- and macrostructure of the streams were measured and determined: flow rate, spray angle, mass distribution of liquid on the surface (spray intensity), non-uniformity of spray density distribution, and average droplet diameters and spray spectrum. A sputter spectrum analyser, using the photoelectric method, was used to determine the microstructural parameters of the stream. Results: The tested nozzles generated dispersed streams with different parameters. Among the analysed nozzles, the highest degree of dispersion was obtained for the TF 6 FCN sample, whose average Sauter mean diameter (SMD) reached a value of 217.3 µm. In comparison, for the NF15 nozzle, this parameter was 945 µm. The spray spectra indicate a high homogeneity of water dispersion in the stream produced by the nozzles TF 6 FCN and CW 50. From the distribution of mass sprinkling density, the CW 50 nozzle shows the greatest uniformity of spraying. At the same time, however, it reports a small amount of water, since the value of the spray density for this product did not exceed 100 g/( m2 · s), while for the NF 15 nozzle it was more than 2,700 g/( m2 · s). The obtained spray angles were close to those declared by the nozzle manufacturer. In the tests of all samples, a slight effect of supply pressure on the values of this parameter was observed. Conclusions: Among other things, the tests made it possible to conclude that in the range of supply pressures of 0.2÷0.6 MPa, the values of disperse angle and spray area of the analysed nozzles were constant or the recorded differences were insignificant. In addition, it was determined that in the case of nozzles with full spray cones, an increase in supply pressure (within the range of declared operating values) has little effect on changing the parameters of the micro- and macro-structure of the stream. The conducted tests showed the potential use of two nozzles (TF6 FCN, CW 50) in low-pressure fog extinguishing systems producing fog with SMD droplet diameters > 200 µm. For the absorption of hazardous substances, it is recommended.
Cel: Celem badań było określenie parametrów mikro- i makrostruktury strumieni wytwarzanych przez dysze różnego typu oraz wskazanie potencjalnych zastosowań badanych dysz wodnych, w tym do gaszenia pożarów i usuwania zanieczyszczeń z powietrza. Projekt i metody: Badaniom poddano dysze wodne TF6 FCN, TF6 V, NF 15 oraz CW 50. Przy ciśnieniu zasilania równym 0,2 MPa, 0,4 MPa oraz 0,6 MPa zmierzono i wyznaczono podstawowe parametry mikro- i makrostruktury strumieni: natężenie przepływu, kąt rozpylenia, rozkład masowy cieczy na powierzchni (intensywność zraszania), nierównomierność rozkładu gęstości zraszania oraz średnie średnice kropel i widmo rozpylenia. Do określenia paramentów mikrostrukturalnych strumienia zastosowano analizator widma rozpylenia, wykorzystujący metodę fotoelektryczną. Wyniki: Badane dysze generowały strumienie rozpylone o różnych parametrach. Wśród analizowanych dysz największy stopień dyspersji uzyskano dla próbki TF 6 FCN, której średnia średnica Sautera (SMD) dochodziła do wartości 217.3 µm. Dla porównania w przypadku dyszy NF15 parametr ten wynosił 945 µm. Widma rozpylenia wskazują na dużą jednorodność dyspersji wody w strumieniu wytworzonym przez dysze: TF 6 FCN i CW 50. Z rozkładu masowej gęstości zraszania wynika, że dysza CW 50 wykazuje największą równomierność zraszania. Jednocześnie podaje ona jednak małą ilość wody, ponieważ wartość gęstości zraszania dla tego wyrobu nie przekroczyła 100 g/(m2 · s), podczas gdy dla dyszy NF 15 wynosiła ona ponad 2700 g/(m2 · s). Uzyskane kąty rozpylenia były zbliżone do deklarowanych przez producenta dysz. W badaniach wszystkich próbek zaobserwowano niewielki wpływ ciśnienia zasilania na wartości tego parametru. Wnioski: Przeprowadzone badania pozwoliły stwierdzić m.in., że w przedziale ciśnień zasilania 0,2÷0,6 MPa wartości kąta rozpylenia oraz powierzchni zraszania analizowanych dysz były stałe lub zarejestrowane różnice była nieznaczne. Dodatkowo ustalono, że w przypadku dysz o pełnych stożkach zraszania wzrost ciśnienia zasilania (w zakresie deklarowanych wartości pracy) ma mały wpływ na zmianę parametrów mikro- i makrostruktury strumienia. Przeprowadzone badania wykazały możliwości potencjalnego zastosowania dwóch dysz (TF6 FCN, CW 50) w niskociśnieniowych mgłowych systemach gaśniczych wytwarzających mgłę o średnicy kropel SMD > 200 µm. Do celów absorpcji substancji niebezpiecznych rekomenduje się zastosowanie dysz o dużym kącie rozpylenia i pełnym stożku zraszania, które – jak pokazały testy – wytwarzają jednorodne strumienie o małej średnicy kropel.
Źródło:
Safety and Fire Technology; 2023, 61, 1; 32-52
2657-8808
2658-0810
Pojawia się w:
Safety and Fire Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Podstawowe aspekty ochrony przeciwpożarowej elektrowni wiatrowych
The basic aspects of fire protection of wind turbines
Autorzy:
Sowa, T.
Powiązania:
https://bibliotekanauki.pl/articles/373720.pdf
Data publikacji:
2011
Wydawca:
Centrum Naukowo-Badawcze Ochrony Przeciwpożarowej im. Józefa Tuliszkowskiego
Tematy:
elektrownia wiatrowa
mgła wodna
ochrona przeciwpożarowa
systemy gaszenia gazem
zasysające systemy detekcji
aspirating smoke systems
fire protection
gaseous extinguishing systems water mist
wind turbine
Opis:
Artykuł zawiera podstawowe informacje na temat ochrony przeciwpożarowej elektrowni wiatrowych lądowych jak również morskich, główne czynniki stwarzające zagrożenie pożarem, rozwiązania techniczne w zakresie detekcji pożaru i jego gaszenia. Opisano również działania prewencyjne, których podjęcie wpłynie pozytywnie na poziom bezpieczeństwa pożarowego.
The article contains Basic information about fire protection of onshore and offshore wind turbines, main possible ignition sources, technical solutions in fire detection and suppression. There are also described prevention actions, that help to improve fire safety level in wind turbines.
Źródło:
Bezpieczeństwo i Technika Pożarnicza; 2011, 2; 103-108
1895-8443
Pojawia się w:
Bezpieczeństwo i Technika Pożarnicza
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Effect of Casting Die Cooling on Solidification Process and Microstructure of Hypereutectic Al-Si Alloy
Autorzy:
Władysiak, R.
Kozuń, A.
Pacyniak, T.
Powiązania:
https://bibliotekanauki.pl/articles/380676.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innovative foundry technology
innovative foundry material
casting die cooling
water mist
hypereutectic silumin
innowacyjna technologia odlewnicza
innowacyjny materiał odlewniczy
odlewanie kokilowe
mgła wodna
silumin nadeutektyczny
Opis:
The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system. The paper presents results of investigation of crystallization process and microstructure of synthetic hypereutectic alloys: AlSi15 and AlSi19. Casts were made in permanent mold cooled with water mist stream. The study was conducted for unmodified silumins on the research station allowing the cooling of the special permanent probe using a program of computer control. Furthermore the study used a thermal imaging camera to analyze the solidification process of hypereutectic silumins. The study demonstrated that the use of mold cooled with water mist stream allows in wide range the formation of the microstructure of hypereutectic silumins. It leads to higher homogeneity of microstructure and refinement of crystallizing phases and also it increases subsequently the mechanical properties of casting.
Źródło:
Archives of Foundry Engineering; 2016, 16, 4; 175-180
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
High-pressure Water Mist Active Firefighting Systems: First Testing Experiences According to Italian Standard UNI 11565
Aktywne systemy gaśnicze z użyciem mgły wodnej pod wysokim ciśnieniem: pierwsze doświadczenia z testów zgodnych z włoską normą UNI 11565
Autorzy:
Barbagli, M.
Powiązania:
https://bibliotekanauki.pl/articles/214818.pdf
Data publikacji:
2016
Wydawca:
Instytut Kolejnictwa
Tematy:
UNI 11565:2014
UNI 11565:2016
fire protection
firefighting
water mist
testing
safety
standard
rolling stock
ochrona przeciwpożarowa
gaszenie pożarów
mgła wodna
badania
bezpieczeństwo
norma
tabor
Opis:
The paper presents the preliminary testing experience of Fogtec in testing and assessing on-board high pressure water mists systems for firefighting in passenger areas of rolling stock according to the new Italian standard UNI 11565:2014. The testing has been conducted in EN 17025 certified laboratories in Italy and Germany. The outcomes collected in this preliminary campaign – as well as similar ones by other manufacturers – constituted the base of the UNI 11565:2014 review process started in September 2015 and finalized in May 2016 with the publication of the UNI 11565:2016.
W artykule opisano wstępne badania firmy FOGTEC, prowadzone według nowej włoskiej normy UNI 11565:2014 nad zastosowaniem mgły wodnej pod wysokim ciśnieniem do gaszenia pożarów w taborze pasażerskim. Badania wykonano we Włoszech i Niemczech w laboratoriach certyfikowanych do prowadzenia badań zgodnie z normą EN 17025. Wyniki badań wstępnych oraz badań przeprowadzonych przez producentów były podstawą przeglądu normy UNI 11565:2014 rozpoczętego we wrześniu 2015 roku i zakończonego w maju 2016 roku publikacją normy UNI 11565:2016.
Źródło:
Problemy Kolejnictwa; 2016, 171; 7-15
0552-2145
2544-9451
Pojawia się w:
Problemy Kolejnictwa
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Structure of water mist stream and its impact on cooling efficiency of casting die
Autorzy:
Władysiak, R.
Budzyński, P.
Powiązania:
https://bibliotekanauki.pl/articles/382910.pdf
Data publikacji:
2012
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
innowacyjne technologie odlewnicze
innowacyjne materiały odlewnicze
odlewanie kokilowe
mgła wodna
mikrostruktura
strumień ciepła
innovative foundry technologies
innovative foundry material
casting die cooling
water mist
microstructure
heat flux
Opis:
The work is a continuation of research on the use water mist cooling in order to increase efficiency of die-casting aluminum alloys. The paper presents results of research and analysis process, spraying water and generated a stream of water mist, the effect of the type of nozzle, the nozzle size and shape of the emitting of the water mist on the wall surface of casting die on the microstructure and geometry of water mist stream and cooling efficiency. Tests were used to perform high-speed camera to record video in the visible and infrared camera. Results were used to develop a computerized image analysis and statistical analysis. The study showed that there are statistical relationships between water and air flow and geometry of the nozzle and nozzle emitting a stream of microstructure parameters of water mist and heat the incoming stream. These relationships are described mathematical models that allow you to control the generating of adequate stream of water mist and a further consequence, the cooling efficiency of casting die.
Źródło:
Archives of Foundry Engineering; 2012, 12, 2; 251-260
1897-3310
2299-2944
Pojawia się w:
Archives of Foundry Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies