Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "spectroscopy" wg kryterium: Temat


Tytuł:
Badanie olejów napędowych metodą dielektrometrii opartą na spektroskopii impedancyjnej
Evaluation of diesel fuels using dielectric spectroscopy
Autorzy:
Macioszek, Ł.
Powiązania:
https://bibliotekanauki.pl/articles/155862.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
dielektrometria
spektroskopia impedancyjna
olej napędowy
dielectric spectroscopy
impedance spectroscopy
diesel fuel
Opis:
W pracy podjęto próbę oceny przydatności dielektrometrii w badaniu właściwości olejów napędowych typu premium. Przy użyciu systemu pomiarowego do spektroskopii impedancyjnej wykonano wstępne badania, na podstawie których wyznaczono względną przenikalność elektryczną badanych próbek. Wyniki badań pozwalają stwierdzić, że przy uwzględnieniu pewnych ograniczeń, dielektrometria oparta o spektroskopię impedancyjną może pozwolić na analizę olejów napędowych.
In the paper an attempt was made to evaluate the diesel fuels using dielectric spectroscopy to verify experimentally that it can be used to characterize these fuels. Five samples of winter premium diesels from different vendors were examined. Impedance of diesel fuels was measured in the frequency range of 0.01 Hz – 5 kHz with the use of EG&G/Princeton Applied Research laboratory system for impedance spectroscopy. Measurement results are presented in the form of Bode plot in Fig. 1. Complex resistivity of the samples was calculated on the basis of measured impedance and is presented on fig. 2. The simplest electrical equivalent circuit of the measuring cell (parallel R-C circuit) was used to calculate the capacitance and thus dielectric constant of diesel fuels (expression 5) from the collected measurements of impedance. Dielectric constant of diesel fuels’ samples is presented in Fig. 3. In the Fig. 1 and 2 one can notice a diversity in the obtained results that depend on the supplier and hence the exact chemical composition of the tested diesel. This diversity is not so noticeable in Fig. 3 what may be very important in cases when dielectric spectroscopy is used to detect some substances that can be harmful for the engine. The tests’ findings show that dielectric spectroscopy can be used to determine some of the properties of diesel fuels. Ability to detect additional substances in diesel would however depend on the difference in values of dielectric constant of the matters.
Źródło:
Pomiary Automatyka Kontrola; 2014, R. 60, nr 11, 11; 942-944
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Influence of Lanthanum Dopant on the Structure and Electric Properties of BaBi2Nb2O9 Ceramics
Autorzy:
Adamczyk-Habrajska, M.
Goryczka, T.
Szalbot, D.
Dzik, J.
Rerak, M.
Bochenek, D.
Powiązania:
https://bibliotekanauki.pl/articles/353535.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
ferroelectric relaxor
ceramics
impedance spectroscopy
Opis:
The paper reports the consequences of lanthanum modifications of barium bismuth niobiate (BaBi2 Nb2 O9) ceramics. The discussed materials were prepared by solid state synthesis and a one-step sintering process. The investigations are focused on dielectric aspects of the modification. The presented results reveal that the trivalent lanthanum ions incorporate twovalent barium ions, which is connected with the creation of A-site cationic vacancies as well as oxygen vacancies. Such a scenario results in significant decreasing in grain boundaries resistivity. The activation energy of grain boundaries conductivity is significantly reduced in the case of lanthanum admixture.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 1; 207-214
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ naprężeń rozciągających na korozję stopu AlMg5 wyznaczoną metodą elektrochemicznej spektroskopii impedancyjnej
Effect of tensile stress corrosion alloy AlMg5 determined by electrochemical impedance spectroscopy
Autorzy:
Jurczak, W.
Powiązania:
https://bibliotekanauki.pl/articles/222482.pdf
Data publikacji:
2005
Wydawca:
Akademia Marynarki Wojennej. Wydział Dowodzenia i Operacji Morskich
Tematy:
korozje
spektroskopia impedancyjna
corrosion
impedance spectroscopy
Opis:
W artykule zamieszczono wyniki badań odporności na korozję w wodzie morskiej stopu poddanego naprężeniu rozciągającemu. W badaniach zastosowano krótkotrwałą metodę pomiarową (t = 200 s), dzięki której oceniono odporność na korozję przez wyznaczenie parametrów warstewki tlenkowej tego stopu, wykorzystując stosowaną obecnie w wielu ośrodkach naukowych zajmujących się problemami korozji metodę dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS) [9, 28]. Inicjacja korozji następuje w wyniku mikropęknięcia warstewki tlenkowej (utrata jej własności ochronnych) i przejścia badanego stopu ze stanu pasywnego w stan aktywny. Stosunkowo niski poziom naprężeń rozciągających, z zakresu granicy odkształceń sprężysto-plastycznych, inicjuje proces korozyjny badanego stopu AlMg5. Szybka repasywacja warstewki tlenkowej Al2O3 występująca przy niskim poziomie naprężeń staje się niemożliwa przy kształtowaniu się przewężenia (szyjki) na rozciąganej próbce.
The paper includes the results of investigations into corrosion resistance of alloy subject to negative stress in sea water. To carry out the investigations a short-term measurement method (t=200s) was used, which allowed for estimating corrosion resistance by means of determining oxygen layer parameters of the alloy. At present the method of dynamic electro-chemical impedance (DEIS) [9, 28] is used in many research centers dealing with the problems of corrosion. Corrosion initiation occurs as a result of microbreaking of oxygen layer (loss of its protective properties) and transfer of the alloy under investigation from the passive state into the active state. Relatively low level of negative stresses, nearing the limits of elastic and plastic strain, initiates the corrosion process of the AlMg5 alloy under investigation. Fast re-passivation of Al2O3oxygen layer occurring at low level of strain becomes impossible at fast shaping of the necking on the strained sample.
Źródło:
Zeszyty Naukowe Akademii Marynarki Wojennej; 2005, R. 46 nr 2 (161), 2 (161); 29-41
0860-889X
Pojawia się w:
Zeszyty Naukowe Akademii Marynarki Wojennej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Komputerowe wspomaganie metody spektroskopii impedancji. Cz. 2 - diagnozowanie stanu technicznego metali
Computer-aided impedance spectroscopy. Part 2. – diagnosis condition of metal
Autorzy:
Żurek, Z.H.
Witoś, M.
Baron, D.
Powiązania:
https://bibliotekanauki.pl/articles/249727.pdf
Data publikacji:
2015
Wydawca:
Instytut Naukowo-Wydawniczy TTS
Tematy:
spektroskopia impedancji
transport
metal
impedance spectroscopy
Opis:
Przedstawiono aspekt metrologiczny niskoczęstotliwościowej spektroskopii impedancji, przykładową aparaturę pomiarową oraz wybrane wyniki badań paramagnetycznych i ferromagnetycznych stopów używanych w transporcie. Główną uwagę zwrócono na identyfikację wiarygodnych symptomów diagnostycznych postępującej degradacji struktury i oceny jakości struktury (elementów nowych i z eksploatacji).
The article presents the aspect of metrological low-frequency impedance spectroscopy, a sample measuring equipment and selected results of paramagnetic and ferromagnetic alloys used in transport. The main attention was paid to the identification of reliable diagnostic symptoms of progressive degradation of the structure and assess the quality of the structure (of new elements and exploitation).
Źródło:
TTS Technika Transportu Szynowego; 2015, 12; 1755-1762, CD
1232-3829
2543-5728
Pojawia się w:
TTS Technika Transportu Szynowego
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A family of new generation miniaturized impedance analyzers for technical object diagnostics
Autorzy:
Hoja, J.
Lentka, G.
Powiązania:
https://bibliotekanauki.pl/articles/220894.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
technical object diagnostics
impedance spectroscopy
impedance analyzer
Opis:
The paper presents the family of three analyzers allowing to measure impedance in the range of 10 Ω<|Zx|<10 GΩ in a wide frequency range from 10 mHz up to 100 kHz. The most important features of the analyzer family are: miniaturization, low power consumption, low production cost, telemetric controlling and the use of an impedance measurement method based on digital signal processing (DSP). The miniaturization and other above-mentioned features of the analyzers were obtained thanks to the use of the newest generation of large-scale integration chips: e.g. "system on a chip" microsystems (AD5933), 32-bit AVR32-family microcontrollers and specialized modules for wireless communication using the ZigBee standard. When comparing metrological parameters, the developed instrumentation can equal portable analyzers offered by top worldwide manufacturers (Gamry, Ivium) but outperforms them on smaller dimensions, weight, a few times lower price and the possibility to work in a distributed telemetric network. All analyzer versions are able to be put into medium-volume production.
Źródło:
Metrology and Measurement Systems; 2013, 20, 1; 43-52
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Impedance Sensors Made in PCB and LTCC Technologies for Monitoring Growth and Degradation of Pseudomonal Biofilm
Autorzy:
Chabowski, K.
Junka, A. F.
Piasecki, T.
Nowak, D.
Nitsch, K.
Smutnicka, D.
Bartoszewicz, M.
Moczała, M.
Szymczyk, P.
Powiązania:
https://bibliotekanauki.pl/articles/221326.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Pseudomonas aeruginosa
biofilm
interdigitated sensor
impedance spectroscopy
Opis:
The suitability of low-cost impedance sensors for microbiological purposes and biofilm growth monitoring was evaluated. The sensors with interdigitated electrodes were fabricated in PCB and LTCC technologies. The electrodes were golden (LTCC) or gold-plated (PCB) to provide surface stability. The sensors were used for monitoring growth and degradation of the reference ATCC 15442 Pseudomonas aeruginosa strain biofilm in invitro setting. During the experiment, the impedance spectra of the sensors were measured and analysed using electrical equivalent circuit (EEC) modelling. Additionally, the process of adhesion and growth of bacteria on a sensor’s surface was assessed by means of the optical and SEM microscopy. EEC and SEM microscopic analysis revealed that the gold layer on copper electrodes was not tight, making the PCB sensors susceptible to corrosion while the LTCC sensors had good surface stability. It turned out that the LTCC sensors are suitable for monitoring pseudomonal biofilm and the PCB sensors are good detectors of ongoing stages of biofilm formation.
Źródło:
Metrology and Measurement Systems; 2017, 24, 2; 369-380
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zastosowanie elektrochemicznej spektroskopii impedancji w badaniach korozji klamer NiTi użytych w osteosyntezie złamań kości twarzy
Application of electrochemical impedance spectroscopy for corrosion investigations of the NiTi staples used in osteosynthesis of the facial bone fractures
Autorzy:
Łosiewicz, B.
Lekston, Z.
Prusik, K.
Winiarski, A.
Jędrusik-Pawłowska, M.
Powiązania:
https://bibliotekanauki.pl/articles/285892.pdf
Data publikacji:
2011
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Polskie Towarzystwo Biominerałów
Tematy:
osteoporoza
spektroskopia impedancji
biomateriały
osteoporosis
impedance spectroscopy
biomaterials
Źródło:
Engineering of Biomaterials; 2011, 14, no. 106-108; 44-49
1429-7248
Pojawia się w:
Engineering of Biomaterials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Woltomierz wektorowy z wykorzystaniem DFT na bazie układu FPGA dla analizatora spektroskopii impedancyjnej
A vector voltmeter using DFT based on the FPGA chip for the impedance spectroscopy analyzer
Autorzy:
Lentka, G.
Kościński, P. A.
Smużyński, K. D.
Powiązania:
https://bibliotekanauki.pl/articles/154373.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
spektroskopia impedancyjna
pomiary impedancji
impedance spectroscopy
impedance measurement
Opis:
W pracy zaproponowano i przetestowano nową koncepcję woltomierza wektorowego z wykorzystaniem cyfrowego przetwarzania sygnałów. Obliczenia prowadzone są sukcesywnie z akwizycją próbek sygnałów pomiarowych, bez gromadzenia ich w pamięci, przy zachowaniu wysokiej częstotliwości próbkowania. Wymaganej mocy obliczeniowej dostarcza układ FPGA. Do obliczania transformaty użyto pamięci wzorca sinusa umieszczonej w układzie FPGA oraz 4 identycznych bloków pracujących równolegle: mnożnika i akumulatora.
In the paper, a new concept of a vector voltmeter for the impedance spectroscopy analyzer is proposed. The voltmeter uses the digital signals processing method for determination of orthogonal parts of measurement signals. The Discrete Fourier Transform calculations are performed “on-the-fly”, successively with acquisition of measurement signals samples, without the need of storing samples in a memory, while assuring the high sampling frequency. The required processing power was supplied by a Spartan 3 FPGA chip. For Fourier transform calculation, the sine pattern stored in the FPGA and 4 identical block sets, a multiplier and an accumulator, were created by Core Generator and used. The previously used vector voltmeter solution was based on a DSP processor with additional circuits (CPLD chip, memories, buffers) and was replaced by a single FPGA chip solution. The selected FPGA offers enough resources and allows reducing the number of additional external components. The prototype of the proposed solution was realized using the FPGA evaluation board with an added module of A/D and D/A converters (Fig. 3). The analyzer was realized in a form of a virtual instrument, the control panel was created by software. The tests were performed on the reference resistors (Figs. 8 and 9). The prototype proved the concept. However, it requires further works. It is necessary to look for a more energy-efficient FPGA chip as well as to optimize the project in terms of powerconsumption minimization.
Źródło:
Pomiary Automatyka Kontrola; 2014, R. 60, nr 9, 9; 694-697
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fast high-impedance spectroscopy method using sinc signal excitation
Autorzy:
Kowalewski, M.
Lentka, G.
Powiązania:
https://bibliotekanauki.pl/articles/220740.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
impedance spectroscopy
sinc signal
Fourier transform
impedance analyzer
Opis:
In this paper the method of fast impedance spectroscopy of technical objects with high impedance (|Zx| ≥ 1 GΩ) is evaluated by means of simulation and a practical experiment. The method is based on excitation of an object with a sinc signal and sampling the response signals proportional to current flowing through and voltage across the measured impedance. The object’s impedance spectrum is obtained with the use of continuous Fourier transform on the basis of linear approximations between samples in two acquisition sections, connected with the duration of the sinc signal. The method is first evaluated in MATLAB by means of simulation. An influence of the sinc signal duration and the number of samples on impedance modulus and argument measurement errors is explored. The method is then practically verified in a constructed laboratory impedance spectroscopy measurement system. The obtained acceleration of impedance spectroscopy in the low frequency range (below 1 Hz) and the decrease of the number of acquired samples enable to recommend the worked out method for implementation in portable impedance analyzers destined for operation in the field.
Źródło:
Metrology and Measurement Systems; 2013, 20, 4; 645-654
0860-8229
Pojawia się w:
Metrology and Measurement Systems
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical analysis and experimental verification of the electrical impedance tomography method for monitoring of the packed-bed drying process
Autorzy:
Porzuczek, J.
Powiązania:
https://bibliotekanauki.pl/articles/175586.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
drying
ectrical impedance tomography
impedance spectroscopy
chokeberry
EIDORS
Opis:
This paper presents a method for online determination the spatial distribution of the moisture content in material being dried. It might be essential for monitoring and optimal control of the drying processes. The proposed method utilizes electrical impedance tomography. As the exemplary material for experimental research the black chokeberry (Aronia melanocarpa) was used. The relationship between electrical impedance of chokeberry and its moisture content was determined for wide range of frequency (0.02200 kHz). Experimental studies of the spatial distribution of the moisture content was performed in the cylindrical vessel equipped with 8-electrode circumferentially arranged. Voltage signal from the electrodes was acquired simultaneously using high-speed data acquisition module. Due to high impedance of the chokeberries, exceeding 109 Ω for dried matter, extraordinary instrumentation for stimulus sourcing and current measurement was necessary to be applied. On the other hand, raw chokeberries are characterized by several orders of magnitude lower impedance (103104 Ω), especially for high frequency. Wide range of observed impedance was able to be measured owing to use of the voltage stimulation instead of the current stimulation. The image reconstruction problem was solved using iterative Gauss-Newton algorithm in the electrical impedance and diuse optical tomography software package. The obtained results has shown satisfactory ability to localize insuciently dried part of the material. It was proved, that strong dependence between moisture content in chokeberries and its impedance in whole frequency range provides more meaningful information than simple resistance or capacitance measurement. Prospect for the improvement of the spatial resolution of humidity imaging was also discussed.
Źródło:
Transactions of the Institute of Fluid-Flow Machinery; 2017, 136; 23-33
0079-3205
Pojawia się w:
Transactions of the Institute of Fluid-Flow Machinery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Hydrogen evolution reaction at Ru-modified nickel-coated carbon fibre in 0.1 M NaOH
Autorzy:
Pierożyński, B.
Mikołajczyk, T.
Powiązania:
https://bibliotekanauki.pl/articles/778010.pdf
Data publikacji:
2015
Wydawca:
Zachodniopomorski Uniwersytet Technologiczny w Szczecinie. Wydawnictwo Uczelniane ZUT w Szczecinie
Tematy:
NiCCF
Ru-modification
hydrogen evolution reaction
HER
impedance spectroscopy
Opis:
The electrochemical activity towards hydrogen evolution reaction (HER) was studied on commercially available (Toho-Tenax) and Ru-modified nickel-coated carbon fibre (NiCCF) materials. Quality and extent of Ru electrodeposition on NiCCF tows were examined by means of scanning electron microscopy (SEM). Kinetics of the hydrogen evolution reaction were investigated at room temperature, as well as over the temperature range: 20-50°C in 0.1 M NaOH solution for the cathodic overpotential range: -100 to -300 mV vs. RHE. Corresponding values of charge-transfer resistance, exchange current-density for the HER and other electrochemical parameters for the examined fibre tow composites were recorded.
Źródło:
Polish Journal of Chemical Technology; 2015, 17, 1; 18-22
1509-8117
1899-4741
Pojawia się w:
Polish Journal of Chemical Technology
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Badanie elektrod o zwiększonej pojemności elektrycznej w spektroskopii impedancyjnej cieczy słaboprzewodzących
The study of electrodes with enhanced capacitance in impedance spectroscopy of poorly conductive liquids
Autorzy:
Macioszek, Ł.
Powiązania:
https://bibliotekanauki.pl/articles/154172.pdf
Data publikacji:
2014
Wydawca:
Stowarzyszenie Inżynierów i Techników Mechaników Polskich
Tematy:
spektroskopia impedancyjna
elektroda pojemnościowa
impedancja
impedance spectroscopy
capacitive electrode
impedance
Opis:
W pracy podjęto próbę oceny elektrod o zwiększonej pojemności elektrycznej, które użyte w spektroskopii impedancyjnej cieczy słaboprzewodzących pozwoliłyby na uzyskanie mniejszych wartości mierzonego modułu impedancji. Wyniki przeprowadzonych badań wskazują, że zarówno poprzez użycie elektrod o gęstszym układzie ścieżek, jak i kształtach ścieżek opartych na fraktalach, możliwe jest osiągnięcie większej pojemności elektrycznej układu elektroda-badana ciecz, a co za tym idzie mniejszych wartości modułu mierzonej impedancji.
In the paper an attempt is made to evaluate the electrodes with enhanced capacitance which used in the impedance spectroscopy of poorly conductive liquids would ensure lower values of impedance modulus. Three capacitive electrodes with different trace shapes are evaluated: basic comb electrode (denoted by I, shown in Fig. 1), comb electrode with denser traces (II, Fig. 2) and electrode III (Fig. 3) with traces of fractal based shapes. The measurements were taken with the use of the Princeton Applied Research laboratory system for electrochemical impedance spectros-copy. The results of impedance modulus measurement of the fresh engine oil are illustrated in Fig. 4, while those of the used engine oil are shown in Fig. 5. The results of impedance modulus meas-urement of the diesel fuel (Fig. 6) and cooking oil (Fig. 7) are also presented in the text. It is visible that the value of the measured impedance modulus is lower for comb electrode II and fractal electrode III than that obtained with electrode I. Table 1 contains the summary of the measured impedance modulus percentage using electrodes comb II and fractal III related to the results of the meas-urements with electrode I (as 100%). The test findings show that both comb electrode with denser traces and the one based on fractal shaped traces can provide greater electrical capacity of the electrode - poorly conductive liquid system and this, as a result, leads to lower values of the measured impedance modulus.
Źródło:
Pomiary Automatyka Kontrola; 2014, R. 60, nr 3, 3; 176-178
0032-4140
Pojawia się w:
Pomiary Automatyka Kontrola
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Fabrication, structural and AC impedance studies of layer-structured Bi4Ti3O12 ceramics
Wytwarzanie, struktura oraz badania impedancyjne warstwowej ceramiki Bi4Ti3O12
Autorzy:
Bernard, H.
Lisińska-Czekaj, A.
Dzik, J.
Osińska, K.
Czekaj, D.
Powiązania:
https://bibliotekanauki.pl/articles/352884.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
tytanian bizmutu
spektroskopia impedancyjna
bismuth titanate
Aurivillius phase
impedance spectroscopy
Opis:
In the present research bismuth titanate Bi4Ti3O12 (BiT) ceramics was synthesized by the standard solid-state reaction method from the mixture of oxides, followed by free sintering at temperature T=1000°C. BiT ceramics was studied in terms of its chemical composition (EDS), crystalline structure (X-ray), microstructure (SEM) and dielectric properties (ac technique of complex impedance spectroscopy) over a range of frequency (f=100Hz to f=1MHz) and temperature (T=200-500°C). Experimental results confirmed the phase formation. It was found that BiT ceramics crystallized in orthorhombic symmetry, best described with Fmmm space group and the following elementary cell parameters: a=5.409(6)°A, b=5.449(2)°A and c=32.816(2)°A. It was also found that BiT ceramics exhibited the plate-like microstructure and stoichiometric chemical composition. Impedance spectroscopy measurements showed contribution of three overlapping relaxation processes (three semicircles in the complex impedance diagrams were observed) ascribed to bulk, grain boundary and electrode/interface polarization phenomena. Impedance data were fitted to the corresponding equivalent circuit using the complex nonlinear least squares (CNLS) method. The ac conductivity for grains, grain boundaries and electrode processes was calculated from CNLS fit of the impedance data and thus the activation energy of ac conductivity (δAC) and relaxation (τ) was calculated for the three revealed components of the impedance spectra from the slopes of δAC and τ versus 1000/T plots (semi log scale) in the range of ΔT=200-500°C.
W prezentowanej pracy ceramikę tytanianu bizmutu Bi4Ti3O12 (BiT) syntezowano metodą reakcji w fazie stałej z mieszaniny prostych tlenków w T=1000 °C. Zbadano skład chemiczny (EDS), strukturę krystaliczna (X-ray), mikrostrukturę (SEM) oraz właściwosci dielektryczne metodą spektroskopii impedancyjnej w zakresie częstotliwości od f =100Hz do f =1MHz w temperaturze T=200-500°C. Analizując obraz SEM można zauważyc, że płytkopodobne ziarna tworza liczne, rozgałęzione prety. Wyniki eksperymentalne potwierdziły wytworzenie się fazy krystalicznej BiT. Ceramika BiT krystalizuje w symetrii rombowej, opisywana jest grupa przestrzenna Fmmm, charakteryzuje się parametrami komórki: a=5.409(6)°A, b=5.449(2)°A, c=32.816(2)°A. Pomiary spektroskopii impendancyjnej wykazały udział trzech nakładających się procesów relaksacyjnych (zaobserwowano trzy półkola przedstawione w diagramach impedancji) przypisanych wnętrzu ziaren, granicy ziaren oraz zjawisk polaryzacji na granicy powierzchni elektroda/próbka. Dane impedancyjne przybliżono odpowiednimi schematami zastępczymi przy użyciu metody złożonych, nieliniowych, najmniejszych kwadratów (CNLS). Wyznaczono przewodnictwo zmiennoprądowe dla ziaren, granic ziaren i procesów elektrodowych oraz energię aktywacji przewodnictwa Eca i relaksacji Eta w zakresie temperatur ΔT=200–500°C.
Źródło:
Archives of Metallurgy and Materials; 2011, 56, 4; 1137-1148
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Zastosowanie elektrochemicznej spektroskopii impedancyjnej do oceny pasywowanych powierzchni drutów stalowych wykorzystywanych na prowadniki kardiologiczne
Application of electrochemical impedance spectroscopy in analysis of surface passivation of steel wires used for cardiological leaders
Autorzy:
Walke, W.
Przondziono, J.
Powiązania:
https://bibliotekanauki.pl/articles/285720.pdf
Data publikacji:
2011
Wydawca:
Akademia Górniczo-Hutnicza im. Stanisława Staszica w Krakowie. Polskie Towarzystwo Biominerałów
Tematy:
spektroskopia impedacyjna
druty stalowe
prowadniki kardiologiczne
impedance spectroscopy
steel wires
cardiological leaders
Źródło:
Engineering of Biomaterials; 2011, 14, no. 106-108; 145-148
1429-7248
Pojawia się w:
Engineering of Biomaterials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling of Dielectric Properties of BiNbO4-Based Microwave Ceramics
Autorzy:
Czekaj, D.
Lisińska-Czekaj, A.
Garbarz-Glos, B.
Bąk, W.
Powiązania:
https://bibliotekanauki.pl/articles/356034.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
BiNbO4 ceramics
impedance spectroscopy
simulation and modelling
quivalent electric circuit method
Opis:
In the present paper results of the studies devoted to computer simulations of dielectric response of electroceramics in a frequency domain as well as analysis of the experimental data are given. As an object of investigations BiNbO4-based microwave ceramics was taken. Simulations of the hypothetical impedance response of the ceramic system were performed under assumption of the brick-layer model. A strategy for analysis and modelling of the impedance data for microwave electroceramics was discussed. On the base of the discussed strategy modelling of the dielectric response of BiNbO4 ceramics was performed with the electric equivalent circuit method. The Voigt’s and Maxwell’s circuits were taken as electric models. Parameters of the electric components of the circuits were determined and related to parameters of the ceramic object under study. It was found that fitting quality was good and changed within the range χ2 = 6.78 × 10-4 – 6.77 × 10-5 depending on the model.
Źródło:
Archives of Metallurgy and Materials; 2020, 65, 3; 1177-1181
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies