Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "przenikanie" wg kryterium: Temat


Tytuł:
The effect of regulating elements on convective heat transfer along shaped heat exchange surfaces
Autorzy:
Cernecky, J.
Koniar, J.
Brodnianska, Z.
Powiązania:
https://bibliotekanauki.pl/articles/185818.pdf
Data publikacji:
2013
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
convection
holographic interferometry
przenikanie ciepła
konwekcja
interferometria holograficzna
Opis:
The paper deals with a study of the effect of regulating elements on local values of heat transfer coefficients along shaped heat exchange surfaces with forced air convection. The use of combined methods of heat transfer intensification, i.e. a combination of regulating elements with appropriately shaped heat exchange areas seems to be highly effective. The study focused on the analysis of local values of heat transfer coefficients in indicated cuts, in distances expressed as a ratio x/s for 0; 0.33; 0.66 and 1. As can be seen from our findings, in given conditions the regulating elements can increase the values of local heat transfer coefficients along shaped heat exchange surfaces. An optical method of holographic interferometry was used for the experimental research into temperature fields in the vicinity of heat exchange surfaces. The obtained values correspond very well with those of local heat transfer coefficients [alfa]x, recorded in a CFD simulation.
Źródło:
Chemical and Process Engineering; 2013, 34, 1; 5-16
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Investigations on heat and momentum transfer in CuO-water nanofluid
Autorzy:
Dzido, G.
Drzazga, M.
Lemanowicz, M.
Gierczycki, A. T.
Powiązania:
https://bibliotekanauki.pl/articles/240561.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
nanofluids
fluid mechanics
heat transfer
nanopłyny
mechanika płynów
przenikanie ciepła
Opis:
This paper presents results of investigations on the application of CuO-water nanofluids for intensification of convective heat transfer. Performance of nanofluids with 2.2 and 4.0 vol.% CuO NPs (nanoparticles) content were examined with regard to heat transfer coefficient and pressure losses in case of turbulent flow in a tube. Negligible impact of examined nanofluid on heat transfer improvement was found. Moreover, measured pressure losses significantly exceeded those determined for primary base liquid. The observations showed that application of nanofluid for heat transfer intensification with a relatively high solid load in the examined flow range is rather controversial.
Źródło:
Archives of Thermodynamics; 2015, 36, 2; 49-59
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Magneto-polar fluid flow through a porous medium of variable permeability in slip flow regime
Autorzy:
Gaur, P. K.
Jha, A. K.
Sharma, R.
Powiązania:
https://bibliotekanauki.pl/articles/266273.pdf
Data publikacji:
2016
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
magnetohydrodynamika
przepuszczalność
przenikanie ciepła
polar fluid
MHD
permeability
slip-flow
heat transfer
Opis:
A theoretical study is carried out to obtain an analytical solution of free convective heat transfer for the flow of a polar fluid through a porous medium with variable permeability bounded by a semi-infinite vertical plate in a slip flow regime. A uniform magnetic field acts perpendicular to the porous surface. The free stream velocity follows an exponentially decreasing small perturbation law. Using the approximate method the expressions for the velocity, microrotation, and temperature are obtained. Further, the results of the skin friction coefficient, the couple stress coefficient and the rate of heat transfer at the wall are presented with various values of fluid properties and flow conditions.
Źródło:
International Journal of Applied Mechanics and Engineering; 2016, 21, 2; 323-339
1734-4492
2353-9003
Pojawia się w:
International Journal of Applied Mechanics and Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
The Influence of Burner Locations in the Heating Furnace on the Charge Temperature Field
Wpływ usytuowania palników w piecu grzewczym na pole temperatury nagrzewanego wsadu do przeróbki plastycznej
Autorzy:
Rywotycki, M.
Szajding, A.
Malinowski, Z.
Telejko, T.
Gołdasz, A.
Beneš, M.
Powiązania:
https://bibliotekanauki.pl/articles/351620.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
industrial furnaces
heat transfer
numerical modelling
piece przemysłowe
przenikanie ciepła
modelowanie numeryczne
Opis:
Charge heating in industrial furnaces is a difficult and complex process. There are many physical phenomena which influence heat transfer. At the charge surface heat transfer takes place by radiation and convection. In order to ensure correct operation of the technological system, it is necessary to achieve the required charge temperature in the whole volume and ensure its uniformity. The influence of selected burner locations inside the furnace on the charge temperature has been analysed. The temperature field and its uniformity in the round charge made of steel for hot open die forging have been analysed. The model and numerical calculations were performed with the ANSYS-Fluent 14.5 package.
Nagrzewanie wsadu w piecach przemysłowych jest trudnym i złożonym procesem. Celem zapewnienia prawidłowej pracy ciągu technologicznego konieczne jest osiągnięcie przez wsad wymaganej temperatury w całej objętości, oraz zapewnienie odpowiedniej równomierności nagrzewania. W pracy określono wpływ sposobu nagrzewania wsadu w piecu komorowym dla wybranych wariantów usytuowania palników grzewczych. Analizie poddano pole temperatury i jego jednorodność w nagrzewanym wsadzie stalowym przeznaczonym do przeróbki plastycznej. Model i obliczenia wykonano pakietem numerycznym ANSYS-Fluent 14.5.
Źródło:
Archives of Metallurgy and Materials; 2015, 60, 3A; 1981-1985
1733-3490
Pojawia się w:
Archives of Metallurgy and Materials
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Modelling of the Temperature Field within Textile Inlayers of Clothing Laminates
Modelowanie pola temperatury we wkładach włókienniczych laminatów odzieżowych
Autorzy:
Korycki, R.
Szafrańska, H.
Powiązania:
https://bibliotekanauki.pl/articles/232203.pdf
Data publikacji:
2013
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
heat transfer
modelling
inlayer
clothing laminates
przenikanie ciepła
modelowanie
wkłady włókiennicze
laminaty odzieżowe
Opis:
Inlayers are introduced to improve the aesthetic qualities and stiffness against the creasing of clothing laminates. The laminate is created by the thermoplastic polymer glue between the inlayer and clothing material, softened by the heat. The connection is secured by the adhesive properties of the polymer and the pressure applied. The state variable is temperature. The heat transfer is described by the heat transport equation as well as by the set of boundary and intial conditions. The temperature distributions within the inlayers are determined by the numerical simulation for different temperatures of the heating plates. The temperature maps are shown by means of the graphical modulus of the program ADINA. The mean temperature of the polymer layer is next calculated.
Wkłady włókiennicze są stosowane w celu poprawy właściwości estetycznych i wzrostu sztywności zgniatania laminatów odzieżowych. Laminat odzieżowy jest tworzony z wykorzystaniem termoplastycznego kleju polimerowego, umieszczonego między wkładem i materiałem odzieżowym, rozrzedzonego za pomocą ciepła. Połączenie jest utrwalane dzięki właściwościom adhezyjnym polimeru oraz przyłożonemu naciskowi. Zmienna stanu to temperatura. Przepływ ciepła jest opisywany za pomocą równania transportu ciepła oraz układu warunków brzegowych i początkowych. Rozkład temperatury we wkładzie można określić za pomocą symulacji numerycznej dla różnych temperatur płyt grzejnych. Mapy temperatury można poddać wizualizacji za pomocą modułu graficznego programu ADINA. Następnie można określić temperaturę warstwy polimeru.
Źródło:
Fibres & Textiles in Eastern Europe; 2013, 4 (100); 118-122
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ ożebrowania rury na warunki wymiany ciepła przy konwekcji swobodnej w powietrzu
The influence of fins on heat transfer performance under free convection in air
Autorzy:
Tychanicz-Kwiecień, Maria
Mazur, Aleksandra
Gil, Paweł
Gałek, Rafał
Powiązania:
https://bibliotekanauki.pl/articles/195178.pdf
Data publikacji:
2019
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
powierzchnie ożebrowane
przenikanie ciepła
konwekcja swobodna
moc cieplna
fins
heat transfer
free convection
thermal power
Opis:
Artykuł przedstawia wstępne wyniki pomiarów cieplnych rurowego wymiennika ciepła typu woda–powietrze, wykonanego z odcinków rur gładkich oraz ożebrowanych z żebrami śrubowymi. Stanowisko pomiarowe znajduje się na wyposażeniu Zakładu Termodynamiki Wydziału Budowy Maszyn i Lotnictwa Politechniki Rzeszowskiej. Dokonano pomiarów mocy cieplnej traconej przez przenikanie na rurze gładkiej oraz ożebrowanej w funkcji różnicy temperatury wody wlotowej i temperatury otoczenia oraz współczynników przenikania ciepła: rury gładkiej – odniesionego do powierzchni zewnętrznej oraz dla rury ożebrowanej – odniesionego do powierzchni całkowitej ożebrowania. Wyniki pomiarów wskazują, że moc cieplna rozpraszana do otoczenia wzrasta niemal trzykrotnie w wyniku zastosowania ożebrowania w stosunku do powierzchni gładkiej. Z kolei współczynnik przenikania ciepła określony dla rury gładkiej osiągnął wartość wielokrotnie większą niż dla rury ożebrowanej.
The article presents preliminary results of thermal parameter measurements of an air-water tubular heat exchanger made of smooth- and finned pipes. The experimental set-up is the equipment of The Department of Thermodynamics at Rzeszow University of Technology. The following parameters have been measured as a function of temperature difference between inlet water temperature and ambient temperature: dissipated thermal power for smooth- and finned pipes and the heat transfer coefficient for a smooth pipe related to the external surface and heat transfer coefficient for a finned pipe related to the overall finned surface. The results indicate that dissipated thermal power increased almost three times for the finned pipe with regard to the smooth pipe. The heat transfer coefficient obtained for a smooth pipe was considerably greater than for a finned pipe.
Źródło:
Zeszyty Naukowe Politechniki Rzeszowskiej. Mechanika; 2019, z. 91 [299], 1-2; 93-107
0209-2689
2300-5211
Pojawia się w:
Zeszyty Naukowe Politechniki Rzeszowskiej. Mechanika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Intensification of heat transfer between heat exchange surfaces at low RE values
Autorzy:
Cernecky, J.
Brodnianska, Z.
Koniar, J.
Powiązania:
https://bibliotekanauki.pl/articles/184897.pdf
Data publikacji:
2015
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
heat exchange surface
Colburn j-factor
interferometry
przenikanie ciepła
powierzchnia wymiany ciepła
interferometria
Opis:
This contribution deals with the heat transfer parameters and pressure losses in heat exchange sets with six geometrical arrangements at low Re values (Re from 476 to 2926). Geometrical arrangements were characterised by the h/H ratio ranging from 0.2 to 1.0. The experiments used the holographic interferometry method in real time. This method enables visible and quantitative evaluations of images of temperature fields in the examined heat exchange. These images are used to determine the local and mean heat transfer parameters. The obtained data were used to determine the Colburn j-factor and the friction coefficient f. The measured values show that by using the profiled heat exchange surfaces and inserting regulating tubes, an intensification of heat transfer (increase of Num, and/or j) was achieved. However, pressure losses recorded a significant increase (increase of f).
Źródło:
Chemical and Process Engineering; 2015, 36, 3; 331-344
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ ramki dystansowej na rozkład temperatury na powierzchni szyby zespolonej w świetle badań termowizyjnych
Influence of the spacer frame on temperature distribution on surface of glazing in the light of thermovision tests
Autorzy:
Lichołai, L.
Starakiewicz, A.
Murias, P.
Szyszka, J.
Powiązania:
https://bibliotekanauki.pl/articles/362740.pdf
Data publikacji:
2015
Wydawca:
Instytut Fizyki Budowli Katarzyna i Piotr Klemm
Tematy:
przegrody przezroczyste
ramka dystansowa
przenikanie ciepła
badania termowizyjne
transparent barriers
spacer frame
heat transfer
thermovision research
Opis:
Przegrody przezroczyste są integralną częścią budynku. Ich rodzaj i jakość wpływa na wewnętrzny komfort użytkowy, a także na bilans cieplny całego obiektu. Poszczególne elementy zestawów szybowych mają znaczenie dla ogólnej charakterystyki termicznej konkretnego rozwiązania okiennego. W niniejszej pracy zamieszczono wyniki badań termowizyjnych różnorodnych zespoleń szybowych. Analizie poddano wpływ zastosowanych ramek dystansowych na rozkład temperatury powierzchni szyby w okolicach jej obrzeża, a w konsekwencji na wartość współczynnika przenikania ciepła szyby Ug.
Transparent barriers are an integral part of the building. Their kind and quality has impact on usable interior comfort, and also on the heat balance of the whole object. The individual elements of the glass sets are important for the general thermal characteristic of each window. The paper presents the results of thermovision tests of different kinds of windows. The influence of used distance frames on the temperature distribution on the glass surface near its periphery, and consequently the value of heat transfer coefficient Ug of the glazing was analyzed.
Źródło:
Fizyka Budowli w Teorii i Praktyce; 2015, T. 7, nr 1, 1; 45-48
1734-4891
Pojawia się w:
Fizyka Budowli w Teorii i Praktyce
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical analysis of the steam flow field in shell and tube heat exchanger
Autorzy:
Bartoszewicz, J.
Bogusławski, L.
Powiązania:
https://bibliotekanauki.pl/articles/240429.pdf
Data publikacji:
2016
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
heat exchanger
shell and tube heat exchanger
przenikanie ciepła
wymiennik ciepła
wymiennik płaszczowo-rurowy
Opis:
In the paper, the results of numerical simulations of the steam flow in a shell and tube heat exchanger are presented. The efficiency of different models of turbulence was tested. In numerical calculations the following turbulence models were used: k-ε, RNG k-ε, Wilcox k-ω, Chen-Kim k-ε, and Lam-Bremhorst k-ε. Numerical analysis of the steam flow was carried out assuming that the flow at the inlet section of the heat exchanger were divided into three parts. The angle of steam flow at inlet section was determined individually in order to obtain the best configuration of entry vanes and hence improve the heat exchanger construction. Results of numerical studies were verified experimentally for a real heat exchanger. The modification of the inlet flow direction according to theoretical considerations causes the increase of thermal power of a heat exchanger of about 14%.
Źródło:
Archives of Thermodynamics; 2016, 37, 2; 107-120
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Application of the interval Lattice Boltzmann method for a numerical modeling of 2D thin metal films irradiated by ultrashort laser pulses
Autorzy:
Piasecka-Belkhayat, Alicja
Korczak, Anna
Powiązania:
https://bibliotekanauki.pl/articles/122840.pdf
Data publikacji:
2019
Wydawca:
Politechnika Częstochowska. Wydawnictwo Politechniki Częstochowskiej
Tematy:
lattice Boltzmann method
interval arithmetic
laser irradiation
heat transfer
metoda kratowa Boltzmanna
arytmetyka przedziałowa
promieniowanie laserowe
przenikanie ciepła
Opis:
In the paper, the two-dimensional numerical modelling of heat transfer in thin metal films irradiated by ultrashort laser pulses using the D2Q9 scheme is considered. In the mathematical description, the relaxation times and the boundary conditions for phonons and electrons are given as interval numbers. The problem has been formulated using the interval coupled lattice Boltzmann equations for electrons and phonons. The solution has been obtained by means of the interval lattice Boltzmann method using the rules of directed interval arithmetic. Examples of numerical computations are presented in the final part of the paper.
Źródło:
Journal of Applied Mathematics and Computational Mechanics; 2019, 18, 4; 63-71
2299-9965
Pojawia się w:
Journal of Applied Mathematics and Computational Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
MHD heat transfer in two-layered flow of conducting fluids through a channel bounded by two parallel porous plates in a rotating system
Autorzy:
Linga Raju, T.
Neela Rao, B.
Powiązania:
https://bibliotekanauki.pl/articles/264768.pdf
Data publikacji:
2016
Wydawca:
Uniwersytet Zielonogórski. Oficyna Wydawnicza
Tematy:
magnetohydrodynamika
przenikanie ciepła
porowatość
MHD
two-layered fluids/immiscible fluids
unsteady flow
heat transfer
rigid rotation
porous boundaries
Opis:
The paper aims to analyze the heat transfer aspects of a two-layered fluid flow in a horizontal channel under the action of an applied magnetic and electric fields, when the whole system is rotated about an axis perpendicular to the flow. The flow is driven by a common constant pressure gradient in the channel bounded by two parallel porous insulating plates, one being stationary and the other one oscillatory. The fluids in the two regions are considered electrically conducting, and are assumed to be incompressible with variable properties, namely, different densities, viscosities, thermal and electrical conductivities. The transport properties of the two fluids are taken to be constant and the bounding plates are maintained at constant and equal temperature. The governing partial differential equations are then reduced to the ordinary linear differential equations by using a two-term series. The temperature distributions in both fluid regions of the channel are derived analytically. The results are presented graphically to discuss the effect on the heat transfer characteristics and their dependence on the governing parameters, i.e., the Hartmann number, Taylor number, porous parameter, and ratios of the viscosities, heights, electrical and thermal conductivities. It is observed that, as the Coriolis forces become stronger, i.e., as the Taylor number increases, the temperature decreases in the two fluid regions. It is also seen that an increase in porous parameter diminishes the temperature distribution in both the regions.
Źródło:
International Journal of Applied Mechanics and Engineering; 2016, 21, 3; 623-648
1734-4492
2353-9003
Pojawia się w:
International Journal of Applied Mechanics and Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Inwentaryzacja rzeczywistych strat ciepła przez przegrody budynków z wykorzystaniem termografii
Assessment of the actual heat loss through building walls by means of thermal imaging
Autorzy:
Kisilewicz, T.
Wróbel, A.
Powiązania:
https://bibliotekanauki.pl/articles/130546.pdf
Data publikacji:
2008
Wydawca:
Stowarzyszenie Geodetów Polskich
Tematy:
termografia
certyfikat energetyczny
budownictwo mieszkaniowe
straty cieplne
przenikanie ciepła
thermography
energy performance certificate
housing industry
heat losses
heat transfer
Opis:
Prawo budowlane nakłada od 1 stycznia 2009 roku obowiązek certyfikacji energetycznej budynków i mieszkań. Certyfikat winien opisywać aktualną efektywność energetyczną budynku. Do ilościowego określenia rzeczywistych własności cieplnych przegród budowlanych można zastosować termografię. Wykorzystanie badań termograficznych jest ograniczone jednak pewnymi warunkami, które muszą być spełnione, aby w wyniku badań można było wyznaczyć prawdziwą wartość izolacyjności cieplnej przegrody. Budynek musi być zamknięty i ogrzewany. Temperatura powietrza na zewnątrz budynku powinna być znacznie niższa od temperatury wewnątrz budynku. Warunki atmosferyczne przed i w czasie pomiaru powinny zapewniać z wystarczającą dokładnością przepływ ciepła zbliżony do ustalonego, a pomiar termograficzny musi być dokonywany od wnętrza budynku. Określenie strat ciepła poprzez przegrody wymaga nie tylko znajomości parametrów cieplnych ściany, ale i wielkości powierzchni odpowiadającej określonej wartości izolacyjności cieplnej. Wykonane termogramy powinny być, zatem zmontowane w jedną mapę rozkładu temperatury na powierzchni badanej przegrody. Do tego celu można wykorzystać stosowane w fotogrametrii programy do przetwarzania rzutowego. W artykule prezentowane są wyniki badań przeprowadzonych z wykorzystaniem kamery TermaCAM firmy FLIR. Na mapach termograficznych badanych ścian widoczne są zarówno mostki cieplne konstrukcyjne jak i spowodowane błędami wykonania. Straty ciepła obliczono jako sumę iloczynów elementarnych powierzchni izotermicznych i przyporządkowanych do nich strumieni ciepła. Stwierdzono, że rzeczywiste straty ciepła przez zewnętrzne ściany budynków są nawet prawie dwukrotnie większe niż wynikałoby to z projektu
According to the new Polish regulations in force as of 1 January 2009, the energy performance certificate will be required on the construction, sale or rent of buildings and dwellings. The certificate should describe the actual energy performance of the building and should provide information regarding, i.a., thermal resistance of the building shell and air exchange. Calculations based only on a building design - if it exists - may lead to unrealistic results due to changes introduced during construction process, a faulty construction or to insulation ageing. Thermography may be used for quantitative investigation of actual thermal features of a building. To assess the real thermal resistance of the wall, a few vital conditions have to be met. The building examined has to be closed and heated. The indoor air temperature should be significantly higher than the temperature outside. Weather conditions before and during the examination should be stable enough to approximate stationary heat flow through the building shell. Thermal inspection must be done inside the building. It is possible To calculate the total heat loss, it is necessary to know both the wall thermal characteristics (surface temperature distribution or heat transfer coefficient) and the wall area. Thermal images have to be set up into a single temperature distribution map. Computer programmes applied in photogrammetry for projective transformation may be used to draw up the temperature distribution maps. The examples of the actual heat loss assessment for walls of different building systems by means of thermal imaging are presented. The analysis was performed with the ThermaCAM S60 camera and FLIR software. Thermal images of the walls examined revealed not only the presence of structural thermal bridges, but also showed defects due to poor workmanship. Total heat losses were calculated as the sum of the products of the elementary isothermal areas and assigned heat flows. It was shown that the real heat losses through the building outer shell may be even two times higher than the values put forth in the designs.
Źródło:
Archiwum Fotogrametrii, Kartografii i Teledetekcji; 2008, 18a; 231-240
2083-2214
2391-9477
Pojawia się w:
Archiwum Fotogrametrii, Kartografii i Teledetekcji
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Study on the Solar Radiation and Heat Transfer of Cabin Fabric Using the Finite Volume Method
Badanie promieniowania słonecznego i przenoszenia ciepła przez tkaniny kabinowe przy użyciu metody objętości skończonych
Autorzy:
Zhang, Yijie
Jia, Juhong
Powiązania:
https://bibliotekanauki.pl/articles/1419824.pdf
Data publikacji:
2021
Wydawca:
Sieć Badawcza Łukasiewicz - Instytut Biopolimerów i Włókien Chemicznych
Tematy:
cabin textile
heat transfer
solar radiation
thermal comfort
numerical simulation
tekstylia kabinowe
przenikanie ciepła
promieniowanie słoneczne
komfort cieplny
symulacja numeryczna
Opis:
The heat transfer of different fabrics was investigated numerically in the cabin of an aircraft. The discrete ordinate (DO) radiation model was adopted to describe the solar radiation through the cabin window and the fabric’s reflection. The conjugate heat transfer between the air flow and the seat fabric was included to study the influence of the textile type and fabric thickness. Some important parameters such as the temperature, radiative heat flux, and heat transfer coefficient on the fabric surface were evaluated. The results showed that both altering of the textile type and thickness will bring about the variation of temperature on the cushion surface. The carbon fibre yarn seat and thinner padding fabric provide a much more enjoyable environment than others. The air circulation in the cabin can improves the thermal environment to some degree.
W pracy zbadano przenikanie ciepła różnych tkanin stosowanych w kabinie samolotu. Do opisu promieniowania słonecznego wpadającego przez okno kabiny i odbicia tkaniny został przyjęty model promieniowania na osi rzędnych dyskretnych (DO). Zbadano wpływ rodzaju tkaniny i grubości tkaniny uwzględniając przenoszenie ciepła koniugatu między przepływem powietrza a tkaniną siedziska. Oceniono niektóre ważne parametry, takie jak: temperatura, strumień ciepła promieniowania i współczynnik przenikania ciepła na powierzchni tkaniny. Wyniki pokazały, że zarówno zmiana rodzaju, jak i grubości tkaniny powoduje zmianę temperatury na powierzchni poduszki. Stwierdzono, że siedzisko z włókna węglowego i cieńsza tkanina wyściełająca zapewniają znacznie przyjemniejsze środowisko, a cyrkulacja powietrza w kabinie może w pewnym stopniu poprawić warunki termiczne.
Źródło:
Fibres & Textiles in Eastern Europe; 2021, 2 (146); 41-47
1230-3666
2300-7354
Pojawia się w:
Fibres & Textiles in Eastern Europe
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical modelling of humid air flow around a porous body
Autorzy:
Bohojło-Wiśniewska, A.
Powiązania:
https://bibliotekanauki.pl/articles/386546.pdf
Data publikacji:
2015
Wydawca:
Politechnika Białostocka. Oficyna Wydawnicza Politechniki Białostockiej
Tematy:
numerical modelling
heat transfer
air flow
mass transfer
chinese cabbage
kapusta pekińska
modelowanie numeryczne
powietrze wilgotne
przepływ powietrza
przenikanie ciepła
warzywa
Opis:
This paper presents an example of humid air flow around a single head of Chinese cabbage under conditions of complex heat transfer. This kind of numerical simulation allows us to create a heat and humidity transfer model between the Chinese cabbage and the flowing humid air. The calculations utilize the heat transfer model in porous medium, which includes the temperature difference between the solid (vegetable tissue) and fluid (air) phases of the porous medium. Modelling and calculations were performed in ANSYS Fluent 14.5 software.
Źródło:
Acta Mechanica et Automatica; 2015, 9, 3; 161-166
1898-4088
2300-5319
Pojawia się w:
Acta Mechanica et Automatica
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical investigation on the effects of obstruction and side ratio on non-Newtonian fluid flow behavior around a rectangular barrier
Autorzy:
Noferesti, Sara
Ghassemi, Hassan
Nowruzi, Hashem
Powiązania:
https://bibliotekanauki.pl/articles/122461.pdf
Data publikacji:
2019
Wydawca:
Politechnika Częstochowska. Wydawnictwo Politechniki Częstochowskiej
Tematy:
non-Newtonian fluids
heat transfer
finite volume method
laminar flow
płyn nieniutonowski
przenikanie ciepła
wymiana ciepła
metoda objętości skończonej
przepływ laminarny
Opis:
In this paper, the characteristics of the flow and forced heat transfer of power law non-Newtonian fluids that flow around a quadrilateral and rectangular cylinder that are located in a 2D channel are investigated by use of the finite volume method (FVM) in a steady state flow regime. To this accomplishment, in the constant temperature, the effects of a different obstruction ratio, aspect ratio and Reynolds number are investigated. The Reynolds number in the range 5 ≤ Re ≤ 40, the power index in the range 0.5 ≤ n ≤ 1.4, the aspect ratio in the range 0.5 ≤ a ≤ 2, and the obstruction ratio in the range 0.125 ≤ b ≤ 0.5 were selected. By surveying the drag coefficient profiles, it’s concluded that as the obstruction ratio increases, the drag coefficient is increased, while an increase in the Reynolds number causes the lower drag coefficient. In addition, the drag coefficient is strongly increased by aspect ratio enhancements.
Źródło:
Journal of Applied Mathematics and Computational Mechanics; 2019, 18, 1; 53-67
2299-9965
Pojawia się w:
Journal of Applied Mathematics and Computational Mechanics
Dostawca treści:
Biblioteka Nauki
Artykuł

Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies