Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "heat power" wg kryterium: Temat


Wyświetlanie 1-11 z 11
Tytuł:
An analysis of coal and coal mine methane co-combustion in an 140 t/h pulverized coal boiler
Autorzy:
Jagodzińska, K.
Hernik, B.
Pronobis, M.
Powiązania:
https://bibliotekanauki.pl/articles/175356.pdf
Data publikacji:
2017
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
Co-combustion
methane
heat transfer
power boiler
Opis:
The paper presents an attempt to evaluate the impact of coal and coal mine methane cocombustion on the physics of the heat exchange in an 140 t/h pulverized-coal boiler through an analysis of 21 combinations of the boiler operating parameters – three different boiler loads (50, 75, and 100%) and seven values of the fired gas thermal contribution (0–60%). The obtained results are the temperature distribution of flue gas and steam in the boiler characteristic points, the heat transfer coefficient values for the boiler individual elements expressing the nature of changes in the heat transfer and the change in the boiler efficiency depending on how much gas is actually fired. An increase in the amount of co-fired gas involves a temperature increase along the flue gas path. This is the effect of the reduction in the amount of heat collected by the evaporator in the furnace. For these reason, the flue gas temperature at the furnace outlet rises by 9 K on average per a 0.1 increment in the fired gas thermal contribution. The temperature rise improves the heat transfer in the boiler heat exchangers – for the first- and the secondstage superheater the improvement totals 2.8% at a 10 pp. increase in the fired gas thermal contribution. However, the rise in the flue gas temperature at the boiler outlet involves a drop in the boiler efficiency (by 0.13 pp. for a rise in the fired gas thermal contribution by 0.1).
Źródło:
Transactions of the Institute of Fluid-Flow Machinery; 2017, 137; 3-18
0079-3205
Pojawia się w:
Transactions of the Institute of Fluid-Flow Machinery
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
A qualitative study of mixing a fluid inside a mechanical mixer with the effect of thermal buoyancy
Autorzy:
Hassouni, Souad
Laidoudi, Houssem
Makinde, Oluwole Daniel
Bouzit, Mohamed
Boumediene, Haddou
Powiązania:
https://bibliotekanauki.pl/articles/2204073.pdf
Data publikacji:
2023
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
mechanical agitation
mixing process
heat transfer
thermal buoyancy
power number
Opis:
This paper is concerned with the rotational motion of the impeller and the thermal buoyancy within a mechanical mixer. The task was investigated numerically using the ANSYS-CFX simulator. The programmer is based on the finite volume method to solve the differential equations of fluid motion and heat transfer. The impeller has hot surfaces while the vessel has cold walls. The rotational movement of the impeller was controlled by the Reynolds number, while the intensity of the thermal buoyancy effect was controlled by the Richardson number. The equations were solved for a steady flow. After analyzing the results of this research, we were able to conclude that there is no effect of the values of Richardson number on the power number. Also, with the presence of the thermal buoyancy effect, the quality of the fluid mixing becomes more important. The increasing Richardson number increases the value of the Nusselt number of the impeller.
Źródło:
Archives of Thermodynamics; 2023, 44, 1; 105--119
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical study of car radiator using dimple roughness and nanofluid
Autorzy:
Thapa, Robin Kumar
Bisht, Vijay Singh
Bhandari, Prabhakar
Rawat, Kamal Singh
Powiązania:
https://bibliotekanauki.pl/articles/2134933.pdf
Data publikacji:
2022
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
heat transfer
augmentation
nanofluid
pumping power
car radiator
artificial roughness
Opis:
Thermal augmentation in flat tube of car radiator using different nanofluids has been performed more often, but use of artificial roughness has been seldom done. Artificial roughness in the form of dimple is used in the present research work. Present study shows the impact of dimple shaped roughness and nanofluid (Al2O3/pure water) on the performance of car radiator. The pitch of dimples is kept at 15 mm (constant) for all the studies performed. The Reynolds number of the flow is selected in the turbulent regime ranging from 9350 to 23 000 and the concentration of the nanofluid is taken in the range of 0.1–1%. It has been found that the heat transfer rate has improved significantly in dimpled radiator tube on the expense of pumping power. Furthermore, the heat transfer rate also increases with increase in nanoparticle concentration from 0.1% to 1.0%. The highest heat transfer enhancement of 79% is observed at Reynolds number 9350, while least enhancement of 18% is observed for Reynolds number of 23 000.
Źródło:
Archives of Thermodynamics; 2022, 43, 3; 125--140
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Formula for temperature distribution in multi-layer optical fibres for high-power fibre lasers
Autorzy:
Grábner, Martin
Peterka, Pavel
Honzátko, Pavel
Powiązania:
https://bibliotekanauki.pl/articles/2063890.pdf
Data publikacji:
2021
Wydawca:
Polska Akademia Nauk. Stowarzyszenie Elektryków Polskich
Tematy:
high-power fibre lasers
active optical fibres
temperature distribution
heat transfer
Opis:
High power fibre lasers need to be cooled efficiently to avoid their thermal damage. Temperature distribution in fibre should be estimated during the fibre laser design process. The steady-state heat equation in a cylindrical geometry is solved to derive a practical formula for temperature radial distribution in multi-layered optical fibres with arbitrary number of the layers. The heat source is located in one or more cylindrical domains. The validity of the analytical formula is tested by comparison with static heat transfer simulations of typical application examples including octagonal double clad fibre, air-clad fibre, fibre with nonuniform, microstructured core. The accuracy sufficient for practical use is reported even for cases with not exactly cylindrical domains.
Źródło:
Opto-Electronics Review; 2021, 29, 4; 126--132
1230-3402
Pojawia się w:
Opto-Electronics Review
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Numerical method for determining the allowable medium temperature during transient operation of a thick-walled boiler element in power plant
Autorzy:
Rząsa, D.
Duda, P.
Powiązania:
https://bibliotekanauki.pl/articles/240222.pdf
Data publikacji:
2011
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
elektrownia
naprężenie cieplne
optymalizacja
wymiana ciepła
heat transfer
optimization
power plant
thermal stresses
Opis:
Secure and cost-effective power generation has become very important nowdays. Care must be taken while designing and operating modern steam power plants. There are regulations such as German boiler regulations (Technische Regeln fur Dampfkessel 301) or European Standards that guide the user how to operate the steam power plants. However, those regulations are based on the quasi-steady state assumption and one dimensional temperature distribution in the entire element. This simplifications may not guarantee that the heating and cooling operations are conducted in the most efficient way. Thus, it was important to find an improved method that can allow to establish optimum parameters for heating and cooling operations. The optimum parameters should guarantee that the maximum total stresses in the construction element are in the allowable limits and the entire process is conducted in the shortest time. This paper summarizes mathematical descriptions how to optimize shut down process of power block devices. The optimization formulation is based on the assumption that the maximum total stresses in the whole construction element should be kept within allowable limits during cooling operation. Additionally, the operation should be processed in the shortest time possible.
Źródło:
Archives of Thermodynamics; 2011, 32, 4; 91-99
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ warunków otoczenia na obciążalność prądową długotrwałą kabli elektroenergetycznych
The impact of the ambient conditions on current-carrying capacity of power cables
Autorzy:
Czapp, S.
Szultka, S.
Dzionk, A.
Borowski, K.
Powiązania:
https://bibliotekanauki.pl/articles/267411.pdf
Data publikacji:
2016
Wydawca:
Politechnika Gdańska. Wydział Elektrotechniki i Automatyki
Tematy:
kable elektroenergetyczne
obciążalność prądowa
wymiana ciepła
power cables
current-carrying capacity
heat transfer
Opis:
Obciążalność prądowa długotrwała przewodów i kabli elektroenergetycznych zależy m.in. od sposobu ich ułożenia i warunków otoczenia. Kabel elektroenergetyczny ułożony w zmiennych warunkach, np. ziemia – woda – powietrze ma obciążalność prądową długotrwałą wynikającą z najgorszych warunków otoczenia pod względem oddawania ciepła. W artykule zaprezentowano wyniki badań symulacyjnych dla linii kablowej niskiego napięcia umieszczonej w zmiennych warunkach gruntowych oraz w zmiennych warunkach w powietrzu, z uwzględnieniem polskich warunków klimatycznych. Opracowane modele i wyniki mogą być wykorzystane do analizy i poprawy obciążalności prądowej długotrwałej linii kablowych oraz stanowić uzupełnienie aktualnych norm.
This paper presents results of analysis of the current-carrying capacity of power cables installed in the ground and in the air. Parameters of ground and air arę variable. The results show that reducing the depth of laying of the power cable and increasing the distance between cables have an effect on increasing the current-carrying capacity. Additionally, in this work the impact of wind speed on the heat transfer in the overhead cable linę is shown. Increase in wind speed may cause an increase in current-carrying capacity of cables.
Źródło:
Zeszyty Naukowe Wydziału Elektrotechniki i Automatyki Politechniki Gdańskiej; 2016, 51; 31-34
1425-5766
2353-1290
Pojawia się w:
Zeszyty Naukowe Wydziału Elektrotechniki i Automatyki Politechniki Gdańskiej
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Maximization of generated electric power in the TEG module at various heat exchange conditions
Autorzy:
Poświata, Artur
Gierycz, Paweł
Powiązania:
https://bibliotekanauki.pl/articles/2034053.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
optimization
thermoelectric
TEG
heat transfer
electric power
optymalizacja
termoelektryczny
wymiana ciepła
energia elektryczna
Opis:
Thermoelectric generators using the Seebeck effect to generate electricity are increasingly used in various areas of human activity, especially in cases where a cheap high-temperature heat source is available. Despite many advantages, TEG generators have one major disadvantage: very low efficiency of heat conversion into electrical power which strongly depends on the applied load resistance. There is a maximum of generated power between the short and the open circuit in which it is zero. That is why optimization of TEG modules is particularly important. In this paper a method of maximization of generated power in a single TEG module is presented for two cases. The first case concerns a problem with fixed heat flux flow into the hot side of the module whereas the second one concerns a problem with fixed heat transfer parameters in hot heat exchanger i.e. supply gas temperature and heat transfer coefficient. A number of optimization results performed for various values of these parameters are presented and discussed.
Źródło:
Chemical and Process Engineering; 2020, 41, 4; 277-291
0208-6425
2300-1925
Pojawia się w:
Chemical and Process Engineering
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Steam condensation analysis in a power plant condenser
Autorzy:
Drożyński, Z.
Powiązania:
https://bibliotekanauki.pl/articles/240848.pdf
Data publikacji:
2018
Wydawca:
Polska Akademia Nauk. Czytelnia Czasopism PAN
Tematy:
condensation
heat transfer
inert gases
power plant condenser
kondensacja
transport ciepła
gazy obojętne
skraplacz energetyczny
Opis:
Proposed is the analysis of steam condensation in the presence of inert gases in a power plant condenser. The presence of inert, noncondensable gases in a condenser is highly undesirable due to its negative effect on the efficiency of the entire cycle. In general, thermodynamics has not provided an explicit criterion for assessing the irreversible heat transfer process. The method presented here enables to evaluate precisely processes occurring in power plant condensers. This real process is of particular interest as it involves a number of thermal layers through which heat transfer is observed. The analysis was performed using a simple, known in the literature and well verified Berman’s model of steam condensation in the presence of non-condensable gases. Adapted to the geometry of the condenser, the model enables, for instance, to recognise places where non-condensable gases are concentrated. By describing with sufficient precision thermodynamic processes taking place in the vicinity of the heat transfer area segment, it is possible to determine the distributions of thermodynamic parameters on the boundaries between successive layers. The obtained results allow for the recognition of processes which contribute in varying degrees to irreversible energy degradation during steam condensation in various parts of the examined device.
Źródło:
Archives of Thermodynamics; 2018, 39, 4; 3-32
1231-0956
2083-6023
Pojawia się w:
Archives of Thermodynamics
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Wpływ ożebrowania rury na warunki wymiany ciepła przy konwekcji swobodnej w powietrzu
The influence of fins on heat transfer performance under free convection in air
Autorzy:
Tychanicz-Kwiecień, Maria
Mazur, Aleksandra
Gil, Paweł
Gałek, Rafał
Powiązania:
https://bibliotekanauki.pl/articles/195178.pdf
Data publikacji:
2019
Wydawca:
Politechnika Rzeszowska im. Ignacego Łukasiewicza. Oficyna Wydawnicza
Tematy:
powierzchnie ożebrowane
przenikanie ciepła
konwekcja swobodna
moc cieplna
fins
heat transfer
free convection
thermal power
Opis:
Artykuł przedstawia wstępne wyniki pomiarów cieplnych rurowego wymiennika ciepła typu woda–powietrze, wykonanego z odcinków rur gładkich oraz ożebrowanych z żebrami śrubowymi. Stanowisko pomiarowe znajduje się na wyposażeniu Zakładu Termodynamiki Wydziału Budowy Maszyn i Lotnictwa Politechniki Rzeszowskiej. Dokonano pomiarów mocy cieplnej traconej przez przenikanie na rurze gładkiej oraz ożebrowanej w funkcji różnicy temperatury wody wlotowej i temperatury otoczenia oraz współczynników przenikania ciepła: rury gładkiej – odniesionego do powierzchni zewnętrznej oraz dla rury ożebrowanej – odniesionego do powierzchni całkowitej ożebrowania. Wyniki pomiarów wskazują, że moc cieplna rozpraszana do otoczenia wzrasta niemal trzykrotnie w wyniku zastosowania ożebrowania w stosunku do powierzchni gładkiej. Z kolei współczynnik przenikania ciepła określony dla rury gładkiej osiągnął wartość wielokrotnie większą niż dla rury ożebrowanej.
The article presents preliminary results of thermal parameter measurements of an air-water tubular heat exchanger made of smooth- and finned pipes. The experimental set-up is the equipment of The Department of Thermodynamics at Rzeszow University of Technology. The following parameters have been measured as a function of temperature difference between inlet water temperature and ambient temperature: dissipated thermal power for smooth- and finned pipes and the heat transfer coefficient for a smooth pipe related to the external surface and heat transfer coefficient for a finned pipe related to the overall finned surface. The results indicate that dissipated thermal power increased almost three times for the finned pipe with regard to the smooth pipe. The heat transfer coefficient obtained for a smooth pipe was considerably greater than for a finned pipe.
Źródło:
Zeszyty Naukowe Politechniki Rzeszowskiej. Mechanika; 2019, z. 91 [299], 1-2; 93-107
0209-2689
2300-5211
Pojawia się w:
Zeszyty Naukowe Politechniki Rzeszowskiej. Mechanika
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Risk of power cables insulation failure due to the thermal effect of solar radiation
Ryzyko uszkodzenia cieplnego izolacji kabli elektroenergetycznych z powodu oddziaływania promieniowania słonecznego
Autorzy:
Czapp, Stanisław
Szultka, Seweryn
Ratkowski, Filip
Tomaszewski, Adam
Powiązania:
https://bibliotekanauki.pl/articles/301538.pdf
Data publikacji:
2020
Wydawca:
Polska Akademia Nauk. Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne PAN
Tematy:
failure risk
heat transfer
numerical modelling
power cables
solar radiation
ryzyko uszkodzenia
wymiana ciepła
modelowanie numeryczne
kable elektroenergetyczne
promieniowanie słoneczne
Opis:
Low-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In some cases, the ampacity of power cables placed in free air is lower than in the ground. Differences in ampacities can be very high if thermal resistivity of the soil is very low, and simultaneously solar irradiation of cables in air occurs. This paper presents the risk of power cables overheating and in consequence the risk of their failure, when part of the underground power cable line is placed in free air. Temperature distribution of cables in the air (with and without solar radiation) for various load currents is presented. Thermal endurance of power cables insulation, operating with the overheating, is estimated.
Linie kablowe zarówno niskiego, jak i wysokiego napięcia zwykle buduje się jako podziemne. Obciążalność kabli układanych w ziemi w znacznym stopniu zależy od rezystywności cieplej gruntu, a może się ona zmieniać w bardzo szerokim zakresie. Obecnie powszechną praktyką jest zasilanie linii kablowych z linii napowietrznych, co sprawia, że pewien odcinek linii kablowej znajduje się w powietrzu i może być poddany bezpośredniemu oddziaływaniu promieniowania słonecznego. W pewnych przypadkach obciążalność prądowa długotrwała kabli w powietrzu jest niższa niż w ziemi – różnice w tej obciążalności mogą być bardzo duże, jeżeli grunt ma niską rezystywność cieplną, a na odcinek linii w powietrzu oddziałuje promieniowanie słoneczne. W artykule przedstawiono problem przegrzania kabli elektroenergetycznych, gdy przyjęta obciążalność linii kablowej wynika z warunków dla ułożenia w ziemi, a na pewnym odcinku linia jest umieszczona w powietrzu. Przedstawiono rozkłady temperatury kabli w powietrzu (z uwzględnieniem i bez uwzględnienia promieniowania słonecznego) dla różnych prądów obciążenia kabli. Oszacowano trwałość termiczną izolacji kabli, mających przez znaczny przedział czasu temperaturę wyższą niż dopuszczalna długotrwale.
Źródło:
Eksploatacja i Niezawodność; 2020, 22, 2; 232-240
1507-2711
Pojawia się w:
Eksploatacja i Niezawodność
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Symulator szybkich procesów dynamiki reaktora jądrowego wodnego ciśnieniowego
Point kinetic and heat transfer basic principles simulator of PWR
Autorzy:
Duzinkiewicz, K.
Cimiński, A.
Michalczyk, Ł.
Powiązania:
https://bibliotekanauki.pl/articles/275769.pdf
Data publikacji:
2013
Wydawca:
Sieć Badawcza Łukasiewicz - Przemysłowy Instytut Automatyki i Pomiarów
Tematy:
symulator
modelowanie matematyczne
reaktor jądrowy
energetyka jądrowa
kinetyka neutronów
wymiana ciepła
simulator
mathematical modelling
nuclear reactor
nuclear power
neutron kinetics
heat transfer
Opis:
W artykule przedstawiono symulator dynamiki reaktora jądrowego (RJ) zbudowany z wykorzystaniem punktowych modeli matematycznych procesów reaktora typu wodnego ciśnieniowego PWR (ang. Pressurized Water Reactor) i zaimplementowany w środowisku MATLAB/Simulink. Symulator stosowany jest obecnie jako narzędzie pomocne w dydaktyce i wstępnych badaniach w zakresie energetyki jądrowej na Politechnice Gdańskiej. W pierwszej części artykułu autorzy skupili się na szybkich procesach i szybkich oddziaływaniach regulacyjnych, czyli kinetyce neutronów, wymianie ciepła w obszarze rdzenia reaktora oraz regulacji kasetami sterującymi. Model obejmuje efekty reaktywnościowe wpływające na procesy kinetyki neutronów wynikające ze zmiany stanu termicznego rdzenia oraz położenia kaset regulacyjnych. W drugiej części artykułu przedstawiono cechy funkcjonalne symulatora.
In the paper point kinetics and heat transfer basic principles simulator of light water nuclear power reactor has been presented. The simulator is used as an educational tool and for a preliminary research. In the first part of the paper point models of the fast processes of the light water nuclear power reactor are presented. The neutron point kinetics and heat transfer, as well as the reactivity effect models are described. In the second part of the paper functionalities of the simulator are demonstrated.
Źródło:
Pomiary Automatyka Robotyka; 2013, 17, 9; 97-101
1427-9126
Pojawia się w:
Pomiary Automatyka Robotyka
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-11 z 11

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies