Temat: welding MIG - Katalog OPAC zbiorów

Skocz do pozycji: 1.

Tytuł:: Influence of joining method for hardness distribution in joints of AlZnSMg1 alloy
Autorzy:: Dudzik, K.
Powiązania:: https://bibliotekanauki.pl/articles/247544.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: friction stir welding (FSW)
welding MIG
aluminium alloys
hardness distribution
Opis:: The article presents the research results of hardness values distribution of friction s tir welded joint (FSW) alloy AW 7020 (AlZn5Mg1). The joints welded by traditional MIG method of the same aluminium alloy were chosen as reference points. Friction stir welding (FSW) - a new technology can be successfully used for butt welding of sheet metal with different types of aluminium alloys. The parameters of friction stir welding (FSW) and MIG welding used to join metal alloy AlZn5Mg1 (7020) were presented. Metallographic analysis showed the correct structured both MIG welded joints and FSW welded aluminum alloy 7020. The study was carried out using Vickers hardness HV5 accordance with the requirements of the Polish Standard PN-EN 1043-1:2000. The study was conducted in three rows, and the indenter load was 50 N. In order to determine the structural changes in the bonded joints, the samples were polished and then micro-etched KELLER reagent. Metallographic examination was carried out using optical microscope Axiovert ZAISS 25. Metallographic examination revealed the existence of an explicit heat affected zone of HAZ in case of MIG welded joints and virtually lack there of, in case of FSW welded joints. In case of FSW welded joint, maximum hardness was observed in the middle of joint, but at a distance of approximately 25 mm from the middle of the weld there is a hardness decrease of about 10% relative to the base material. In the MIG weldedjoint lowest hardness of the weld occurred in the middle of the joint.
Źródło:: Journal of KONES; 2010, 17, 4; 137-141
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 2.

Tytuł:: Influence of friction stir welding on impact resistance of AlZn5Mg1 alloy joints
Wpływ zgrzewania tarciowego FSW na udarność złączy spajanych stopu AlZnSMgl
Autorzy:: Dudzik, K.
Czechowski, M.
Powiązania:: https://bibliotekanauki.pl/articles/242212.pdf
Data publikacji:: 2009
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: zgrzewanie tarciowe FSW
spawanie MIG
stopy aluminium
udarność
friction stir welding (FSW)
aluminium alloys
impact resistance
welding MIG
Opis:: The paper presents the research results on impact resistance of friction s tir welded aluminum alloy A W 7020 [AlZn5MglJ. The joints welded by traditional MIG method of the same aluminium alloy were chosen as reference points. Friction Stir Welding (FSW) - a new technology can be successfully used for butt welding of different types of aluminum alloy sheets. The parameters for friction stir welding of sheets made of AlZn5Mgl [7020] alloy were introduced in the article. Metallographic analysis of bonds showed proper structural construction of the friction stir welded 7020 aluminum alloys. The impact resistance was examined via the Charpy test according to PN-EN 10045-1. During test the hammer angle of deflection beta after hitting was noted and next the brake work "L " and impact resistance "U" were determined. The tests were carried out on typical specimens of cuboids shape (55x10x10 mm), with "V" notch. The research was conducted at the temperature of + 20°C. After impact resistance test the failure surface of specimens was analyzed by scanning with electron microscope SEM Philips XL30. The research of impact resistance showed that the values of 7020 alloy welded by FSW method were higher compared to the properties of 7020 alloy joints welded by traditional MIG method — the average impact resistance was about 18% higher in case ofFSW then in MG.
W artykule przedstawiono wyniki badań udarności złączy zgrzewanych tarciowo (FSW) stopu AW 7020 (AlZn5Mgl). Jako punkt odniesienia wybrano zlącza tego samego stopu spawane tradycyjną metodą MIG. Nową technologię zgrzewania tarciowego z przemieszaniem materiału zgrzeiny FSW (Friction Stir Welding) można z powodzeniem stosować do zgrzewania doczołowego blach z różnego rodzaju stopów aluminium. Przedstawiono parametry zgrzewania tarciowego (FSW) zastosowane do połączenia blach ze stopu AlZn5Mgl (7020). Analiza metalograficzna wykazała poprawną budowę strukturalną złączy zgrzewanych stopu aluminium 7020. Badania udarności przeprowadzono metodą Charpy'ego zgodnie z wymaganiami Polskiej Normy PN-EN 10045-1. Podczas badań odczytano kąt wychylenia młota po uderzeniu beta a następnie wyznaczono pracę łamania L oraz udarność U. Próbki do badań udarności wykonano jako standardowe, w kształcie prostopadłościanu o wymiarach 55x10x10 mm z zalecaną przez normę dokładnością š0,1 mm, w których wycięto karb w kształcie litery V. Próbę przeprowadzono w temperaturze + 20°C. Po badaniach udarności przeprowadzono analizę powierzchni przełomów próbek za pomocą mikroskopu elektronowego (SEM) Philips XL3O. Badania udarności złączy stopu 7020 wykazały wyższą wartość udarności w przypadku zastosowania zgrzewania tarciowego FSW w porównaniu do tradycyjnej metody spawalniczej MIG - średnio udarność była wyższa o ok. 18%.
Źródło:: Journal of KONES; 2009, 16, 3; 93-98
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 3.

Tytuł:: The influence of joining method of AW-7020 aluminium alloy on corrosion properties
Autorzy:: Dudzik, K.
Powiązania:: https://bibliotekanauki.pl/articles/247476.pdf
Data publikacji:: 2011
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: aluminium alloys
friction stir welding (FSW)
MIG welding
corrosion
Opis:: The results of corrosion properties research of aluminum alloy AW 7020 (AlZn5Mg1) welded by friction stir welding FSW and MIG were presented. Friction Stir Welding (FSW) - a new technology can be successfully used for butt welding of different types of aluminum alloy sheets. In the article the parameters for friction stir welding of sheets made of AlZn5Mg1 [7020] alloy was presented as well as parameters for MIG. Metallographic analysis of bonds showed a proper structural construction of both, the FSW and MIG welded 7020 aluminum alloys. The polarization was carried out at changes in the potential speed of 12 mV/min in the range of š 50 mV with the stationary potential. Atlas 0531EU & IA potentiostat was used for studies. The corrosion resistance research was carried out using three electrode potentiodynamic method. The following parameters were measured: electrode potential Ec [mV] and the corrosion current density Jc [mi A/cm2]. The tests were carried out on specimens in 3.5% water solution NaCl. Good resistance to electrochemical corrosion was found of the native material, friction stir welded and MIG welded 7020 aluminum alloys. Original value are received results of the corrosion properties of new method friction stir welded AlZn5Mg1 alloy compared with traditional MIG method and the native material.
Źródło:: Journal of KONES; 2011, 18, 4; 587-581
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 4.

Tytuł:: Microscopic examination of AlZn5Mg1 alloy joints welded by FSW and MIG
Autorzy:: Dudzik, K.
Charchalis, A.
Jurczak, W.
Powiązania:: https://bibliotekanauki.pl/articles/247908.pdf
Data publikacji:: 2012
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: microscopic examination
aluminium alloys
friction stir welding (FSW)
MIG welding
grain size
Opis:: The article presents the research results of microscopic examination of friction stir welded joint (FSW) alloy AW 7020 (AlZn5Mg1). The joints welded by traditional MIG method of the same aluminium alloy were chosen as reference points. Friction stir welding (FSW) - a new technology can be successfully used for butt welding of sheet metal with different types of aluminium alloys. The parameters of friction stir welding (FSW) and MIG welding used to join metal alloy AlZn5Mg1 (7020) were presented. Welds made using both the FSW and MIG method were checked using X-ray flaw detection and showed no welding defects. In order to determine the structural changes in the bonded joints, the samples were polished and then microetched KELLER reagent. Metallographic examination was carried out using optical microscope Axiovert ZAISS 25. To determine the grain size in the different zones of joints welded by FSW and MIG methods AxioVision 4.8.2 software was used. Metallographic examination revealed the existence of an explicit heat affected zone of HAZ in case of MIG welded joints and virtually lack thereof, in case of FSW welded joints. Microscopic examination of AlZn5Mg1 alloy joints showed that the structure of the FSW welded joint is more homogeneous than the MIG welded joint. The analysis of the grain size of the characteristic zones of joints shows that in the case of joints welded by FSW the weld nugget has smaller grains than the native material. In case of the joint welded by traditional MIG method the biggest grains are in HAZ and the smallest in the native material.
Źródło:: Journal of KONES; 2012, 19, 2; 129-135
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Skocz do pozycji: 5.

Tytuł:: Stress corrosion cracking of 7020 aluminium alloy jointed by different welding methods
Autorzy:: Dudzik, K.
Powiązania:: https://bibliotekanauki.pl/articles/247592.pdf
Data publikacji:: 2010
Wydawca:: Instytut Techniczny Wojsk Lotniczych
Tematy:: aluminium alloys
friction stir welding (FSW)
MIG welding
stress corrosion cracking
mechanical properties
slow-strain-rate-testing
Opis:: The results of stress corrosion cracking (SCC) of aluminum alloy AW 7020 [AlZn5Mg1] welded by friction stir welding FSW and MIG were presented. Friction Stir Welding (FSW) - a new technology can be successfully used for butt welding of different types of aluminum alloy sheets. In the article the parameters for friction stir welding ofsheets made of AlZn5Mg1 [7020] alloy was presented as well as parameters for MIG. Metallographic analysis of bonds showed a proper structural construction of both, the FSW and MIG welded 7020 aluminum alloys. Stress corrosion cracking was examined via the slow-strain-rate-testing (SSRT) according to EN ISO 7539-7. The following parameters were measured: time-to-failure - T [h], obtained max. load - F [N]; strain energy (the diagram surface under the stress-elongation curve) - E [MJ/m3]; relative elongation of the specimen — a10 [%]; max. tensile stress — R [MPa] and contraction — Z [%]. The tests were carried out on cylindrical notch-free specimens in the air and 3.5% water solution NaCl. Good resistance to stress corrosion was found of friction stir welded 7020 aluminum alloys. The tested samples cracked during SSRT test in the native material in case of FSW and in the joint in case of MIG. Original value are received results of the stress corrosion resistance of new method friction stir welded AlZn5Mg1 alloy compared with traditional MIG method.
Źródło:: Journal of KONES; 2010, 17, 4; 143-147
1231-4005
2354-0133
Pojawia się w:: Journal of KONES
Dostawca treści:: Biblioteka Nauki

Artykuł

Zmień widok

na półce

Informacja

Wyszukujesz frazę "welding MIG" wg kryterium: Temat

Źródło danych

Dostawca treści

Kolekcja

Rok wydania

Wydawca

Temat

Autor

Typ dokumentu

Język