Informacja

Drogi użytkowniku, aplikacja do prawidłowego działania wymaga obsługi JavaScript. Proszę włącz obsługę JavaScript w Twojej przeglądarce.

Wyszukujesz frazę "piston internal combustion engine" wg kryterium: Temat


Wyświetlanie 1-3 z 3
Tytuł:
Research results of novel composite materials with low hysteresis during heating and cooling for pistons of combustion engines
Autorzy:
Sieminska, B.
Powiązania:
https://bibliotekanauki.pl/articles/245037.pdf
Data publikacji:
2010
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engines
engine piston
thermal expansion
emissions
Opis:
Research results of novel silumins on pistons for combustion engines, which have high mechanical properties within the range of piston higher operating temperatures, 100-300°C, are presented in the paper. Silumins contain enlarging concentration of the nickel and copper alloy additives up to 4.0, and chrome and molybdenum alloy additives up to 1.0%. Occurrence of given microstructure in piston-silumins results in almost the same values of the coefficient thermal expansion during the heating up to the 300 °C temperature and during the next cooling into the ambient temperature. Small values of the coefficient of expansion of thermal and small differences between values of the coefficient of thermal expansion during heating and cooling enable on application of small values of working clearances between piston and the cylinder liner. As a consequence they make possible, the low exhaust emission level, and the low noise level. The pistons from alloys with small values ofthe coefficient of thermal expansion, small differences of this coefficient during heating and cooling are novel aspects presented in paper. Research results of strength and metallographic parameters, research results of the coefficient of thermal expansion, comparative engine research results are represented in the paper. In particular representative chemical components for a standard alloy and novel alloy, mechanical properties investigated alloys after solution heat treatment, wear resistance of novel alloy compared with two cast irons, ATD curves, fibrous construction, silicon construction, microstructure of novel alloy, courses of changes of the coefficient of thermal expansion in the function of the temperature during heating and cooling are presented in the paper.
Źródło:
Journal of KONES; 2010, 17, 1; 421-432
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Verification of the precise position of the aircraft in air navigation based on the solution of the RTK-OTF technique
Autorzy:
Kowalski, M.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/242780.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engine
Diesel engine
engine piston
composite alloy
thermal stability
Opis:
Certain results of the comparative studies of the high-speed Diesel engine V-12 of the “W” series were presented in the article. The engine was modernised in regard of possibilities to achieve better performances at specific fuel consumption, smaller exhaust emission, smaller scavenge, lower noise and better thermal stability. The subject of this work is the piston cast of novel composite silumin. The development of novel composite silumin (aluminium-silicon alloy), which contains a little more Copper and Nickel, and the introduction of novel alloyed elements, such as Chromium, Molybdenum, Tungsten, increases the strength of the alloy and its thermal stability during successive heating and cooling. The pistons made of this alloy may have a little bigger outside diameter than the pistons made of PA-12 standard alloy, and a smaller clearance between the piston and cylinder liner. The pistons made of standard and novel alloy were mounted successively in the "W" engine. The full load and part load curves were determined. The lubrication oil consumption, fuel consumption, exhaust emission, blow-by and noise were determined too. The article presents the results of the above-mentioned research. The novel composite alloy enables further engine modernization because the engine should operate at higher pressure and temperature in the combustion chamber.
Źródło:
Journal of KONES; 2017, 24, 4; 99-108
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
Tytuł:
Research performance of novel design of diesel engine
Autorzy:
Kowalski, M.
Jankowski, A.
Powiązania:
https://bibliotekanauki.pl/articles/949487.pdf
Data publikacji:
2017
Wydawca:
Instytut Techniczny Wojsk Lotniczych
Tematy:
internal combustion engine
Diesel engine
engine piston
composite alloy
thermal stability
Opis:
Certain results of the comparative studies of the high-speed Diesel engine V-12 of the “W” series were presented in the article. The engine was modernised in regard of possibilities to achieve better performances at specific fuel consumption, smaller exhaust emission, smaller scavenge, lower noise and better thermal stability. The subject of this work is the piston cast of novel composite silumin. The development of novel composite silumin (aluminium-silicon alloy), which contains a little more Copper and Nickel, and the introduction of novel alloyed elements, such as Chromium, Molybdenum, Tungsten, increases the strength of the alloy and its thermal stability during successive heating and cooling. The pistons made of this alloy may have a little bigger outside diameter than the pistons made of PA-12 standard alloy, and a smaller clearance between the piston and cylinder liner. The pistons made of standard and novel alloy were mounted successively in the "W" engine. The full load and part load curves were determined. The lubrication oil consumption, fuel consumption, exhaust emission, blow-by and noise were determined too. The article presents the results of the above-mentioned research. The novel composite alloy enables further engine modernization because the engine should operate at higher pressure and temperature in the combustion chamber.
Źródło:
Journal of KONES; 2017, 24, 4; 99-108
1231-4005
2354-0133
Pojawia się w:
Journal of KONES
Dostawca treści:
Biblioteka Nauki
Artykuł
    Wyświetlanie 1-3 z 3

    Ta witryna wykorzystuje pliki cookies do przechowywania informacji na Twoim komputerze. Pliki cookies stosujemy w celu świadczenia usług na najwyższym poziomie, w tym w sposób dostosowany do indywidualnych potrzeb. Korzystanie z witryny bez zmiany ustawień dotyczących cookies oznacza, że będą one zamieszczane w Twoim komputerze. W każdym momencie możesz dokonać zmiany ustawień dotyczących cookies